This adds basic support for the Tegra2 USB controller. Board files should call board_usb_init() to set things up.
Configuration through FDT and CONFIG is supported. For FDT, the device tree aliases set the order of the port, like this fragment:
aliases { /* This defines the order of our USB ports */ usb0 = "/usb@0xc5008000"; usb1 = "/usb@0xc5000000"; };
For CONFIG-based configuration, where CONFIG_OF_CONTROL is not defined, USB ports rely on CONFIG_TEGRA2_USBx macros to select the ordering. For example:
#define CONFIG_TEGRA_USB0 TEGRA_USB3_BASE #define CONFIG_TEGRA_USB1 TEGRA_USB1_BASE
We record the order that the ports are configured and use that to select ports by number.
Signed-off-by: Simon Glass sjg@chromium.org --- Changes in v2: - Rename params to timing - Store entire fdt config in port list, not just register pointer - Remove non-fdt operation of USB, since it is not needed - Decode USB VBUS GPIO from the fdt - Decode phy type differently (to match new kernel fdt) - Rename tegra20-usb to tegra20-ehcui (to match new kernel fdt) - Improve debug() printouts in case of failure to init USB
arch/arm/cpu/armv7/tegra2/Makefile | 4 +- arch/arm/cpu/armv7/tegra2/usb.c | 398 +++++++++++++++++++++++++++++ arch/arm/include/asm/arch-tegra2/tegra2.h | 2 + arch/arm/include/asm/arch-tegra2/usb.h | 255 ++++++++++++++++++ drivers/usb/host/Makefile | 1 + drivers/usb/host/ehci-tegra.c | 63 +++++ include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 8 files changed, 724 insertions(+), 1 deletions(-) create mode 100644 arch/arm/cpu/armv7/tegra2/usb.c create mode 100644 arch/arm/include/asm/arch-tegra2/usb.h create mode 100644 drivers/usb/host/ehci-tegra.c
diff --git a/arch/arm/cpu/armv7/tegra2/Makefile b/arch/arm/cpu/armv7/tegra2/Makefile index 955c3b6..70e7abd 100644 --- a/arch/arm/cpu/armv7/tegra2/Makefile +++ b/arch/arm/cpu/armv7/tegra2/Makefile @@ -33,8 +33,10 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(SOC).o
SOBJS := lowlevel_init.o -COBJS := ap20.o board.o clock.o pinmux.o sys_info.o timer.o +COBJS-y := ap20.o board.o clock.o pinmux.o sys_info.o timer.o +COBJS-$(CONFIG_USB_EHCI_TEGRA) += usb.o
+COBJS := $(COBJS-y) SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS) $(SOBJS))
diff --git a/arch/arm/cpu/armv7/tegra2/usb.c b/arch/arm/cpu/armv7/tegra2/usb.c new file mode 100644 index 0000000..f2173a7 --- /dev/null +++ b/arch/arm/cpu/armv7/tegra2/usb.c @@ -0,0 +1,398 @@ +/* + * Copyright (c) 2011 The Chromium OS Authors. + * (C) Copyright 2010,2011 NVIDIA Corporation <www.nvidia.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm-generic/gpio.h> +#include <asm/arch/tegra2.h> +#include <asm/arch/clk_rst.h> +#include <asm/arch/clock.h> +#include <asm/arch/gpio.h> +#include <asm/arch/pinmux.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/uart.h> +#include <asm/arch/usb.h> +#include <libfdt.h> +#include <fdtdec.h> + +enum { + USB_PORTS_MAX = 4, /* Maximum ports we allow */ +}; + +/* Parameters we need for USB */ +enum { + PARAM_DIVN, /* PLL FEEDBACK DIVIDer */ + PARAM_DIVM, /* PLL INPUT DIVIDER */ + PARAM_DIVP, /* POST DIVIDER (2^N) */ + PARAM_CPCON, /* BASE PLLC CHARGE Pump setup ctrl */ + PARAM_LFCON, /* BASE PLLC LOOP FILter setup ctrl */ + PARAM_ENABLE_DELAY_COUNT, /* PLL-U Enable Delay Count */ + PARAM_STABLE_COUNT, /* PLL-U STABLE count */ + PARAM_ACTIVE_DELAY_COUNT, /* PLL-U Active delay count */ + PARAM_XTAL_FREQ_COUNT, /* PLL-U XTAL frequency count */ + PARAM_DEBOUNCE_A_TIME, /* 10MS DELAY for BIAS_DEBOUNCE_A */ + PARAM_BIAS_TIME, /* 20US DELAY AFter bias cell op */ + + PARAM_COUNT +}; + +/* Information about a USB port */ +struct fdt_usb { + struct usb_ctlr *reg; /* address of registers in physical memory */ + u32 timing[PARAM_COUNT]; /* timing parameters */ + int host_mode; /* 1 if port has host mode, else 0 */ + int utmi; /* 1 if port has external tranceiver, else 0 */ + int enabled; /* 1 to enable, 0 to disable */ + enum periph_id periph_id;/* peripheral id */ + struct fdt_gpio_state vbus_gpio; /* GPIO for vbus enable */ +}; + +static struct fdt_usb port[USB_PORTS_MAX]; /* List of valid USB ports */ +static unsigned port_count; /* Number of available ports */ +static int port_current; /* Current port (-1 = none) */ + +/* Record which controller can switch from host to device mode */ +static struct fdt_usb *host_dev_ctlr; + +/* UTMIP Idle Wait Delay */ +static const u8 utmip_idle_wait_delay = 17; + +/* UTMIP Elastic limit */ +static const u8 utmip_elastic_limit = 16; + +/* UTMIP High Speed Sync Start Delay */ +static const u8 utmip_hs_sync_start_delay = 9; + +/* Put the port into host mode (this only works for USB1) */ +static void set_host_mode(struct fdt_usb *config) +{ + /* Check whether remote host from USB1 is driving VBus */ + if (readl(&config->reg->phy_vbus_sensors) & VBUS_VLD_STS) + return; + + /* + * If not driving, we set GPIO USB1_VBus_En. We assume that the + * pinmux is set up correctly for this. + */ + if (fdt_gpio_isvalid(&config->vbus_gpio)) { + fdtdec_setup_gpio(&config->vbus_gpio); + gpio_direction_output(config->vbus_gpio.gpio, 1); + } +} + +/* Put our ports into host mode */ +void usb_set_host_mode(void) +{ + if (host_dev_ctlr) + set_host_mode(host_dev_ctlr); +} + +void usbf_reset_controller(enum periph_id id, struct usb_ctlr *usbctlr) +{ + /* Reset the USB controller with 2us delay */ + reset_periph(id, 2); + + /* + * Set USB1_NO_LEGACY_MODE to 1, Registers are accessible under + * base address + */ + if (id == PERIPH_ID_USBD) + setbits_le32(&usbctlr->usb1_legacy_ctrl, USB1_NO_LEGACY_MODE); + + /* Put UTMIP1/3 in reset */ + setbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET); + + /* Set USB3 to use UTMIP PHY */ + if (id == PERIPH_ID_USB3) + setbits_le32(&usbctlr->susp_ctrl, UTMIP_PHY_ENB); + + /* + * TODO: where do we take the USB1 out of reset? The old code would + * take USB3 out of reset, but not USB1. This code doesn't do either. + */ +} + +/* set up the USB controller with the parameters provided */ +static void init_usb_controller(enum periph_id id, struct usb_ctlr *usbctlr, + const u32 *timing) +{ + u32 val; + int loop_count; + + clock_enable(id); + + /* Reset the usb controller */ + usbf_reset_controller(id, usbctlr); + + /* Stop crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN low */ + clrbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN); + + /* Follow the crystal clock disable by >100ns delay */ + udelay(1); + + /* + * To Use the A Session Valid for cable detection logic, VBUS_WAKEUP + * mux must be switched to actually use a_sess_vld threshold. + */ + if (id == PERIPH_ID_USBD) { + clrsetbits_le32(&usbctlr->usb1_legacy_ctrl, + VBUS_SENSE_CTL_MASK, VBUS_SENSE_CTL_A_SESS_VLD); + } + + /* + * PLL Delay CONFIGURATION settings. The following parameters control + * the bring up of the plls. + */ + val = readl(&usbctlr->utmip_misc_cfg1); + clrsetbits_le32(&val, UTMIP_PLLU_STABLE_COUNT_MASK, + timing[PARAM_STABLE_COUNT] << UTMIP_PLLU_STABLE_COUNT_SHIFT); + clrsetbits_le32(&val, UTMIP_PLL_ACTIVE_DLY_COUNT_MASK, + timing[PARAM_ACTIVE_DELAY_COUNT] << + UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT); + writel(val, &usbctlr->utmip_misc_cfg1); + + /* Set PLL enable delay count and crystal frequency count */ + val = readl(&usbctlr->utmip_pll_cfg1); + clrsetbits_le32(&val, UTMIP_PLLU_ENABLE_DLY_COUNT_MASK, + timing[PARAM_ENABLE_DELAY_COUNT] << + UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT); + clrsetbits_le32(&val, UTMIP_XTAL_FREQ_COUNT_MASK, + timing[PARAM_XTAL_FREQ_COUNT] << + UTMIP_XTAL_FREQ_COUNT_SHIFT); + writel(val, &usbctlr->utmip_pll_cfg1); + + /* Setting the tracking length time */ + clrsetbits_le32(&usbctlr->utmip_bias_cfg1, + UTMIP_BIAS_PDTRK_COUNT_MASK, + timing[PARAM_BIAS_TIME] << UTMIP_BIAS_PDTRK_COUNT_SHIFT); + + /* Program debounce time for VBUS to become valid */ + clrsetbits_le32(&usbctlr->utmip_debounce_cfg0, + UTMIP_DEBOUNCE_CFG0_MASK, + timing[PARAM_DEBOUNCE_A_TIME] << UTMIP_DEBOUNCE_CFG0_SHIFT); + + setbits_le32(&usbctlr->utmip_tx_cfg0, UTMIP_FS_PREAMBLE_J); + + /* Disable battery charge enabling bit */ + setbits_le32(&usbctlr->utmip_bat_chrg_cfg0, UTMIP_PD_CHRG); + + clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_XCVR_LSBIAS_SE); + setbits_le32(&usbctlr->utmip_spare_cfg0, FUSE_SETUP_SEL); + + /* + * Configure the UTMIP_IDLE_WAIT and UTMIP_ELASTIC_LIMIT + * Setting these fields, together with default values of the + * other fields, results in programming the registers below as + * follows: + * UTMIP_HSRX_CFG0 = 0x9168c000 + * UTMIP_HSRX_CFG1 = 0x13 + */ + + /* Set PLL enable delay count and Crystal frequency count */ + val = readl(&usbctlr->utmip_hsrx_cfg0); + clrsetbits_le32(&val, UTMIP_IDLE_WAIT_MASK, + utmip_idle_wait_delay << UTMIP_IDLE_WAIT_SHIFT); + clrsetbits_le32(&val, UTMIP_ELASTIC_LIMIT_MASK, + utmip_elastic_limit << UTMIP_ELASTIC_LIMIT_SHIFT); + writel(val, &usbctlr->utmip_hsrx_cfg0); + + /* Configure the UTMIP_HS_SYNC_START_DLY */ + clrsetbits_le32(&usbctlr->utmip_hsrx_cfg1, + UTMIP_HS_SYNC_START_DLY_MASK, + utmip_hs_sync_start_delay << UTMIP_HS_SYNC_START_DLY_SHIFT); + + /* Preceed the crystal clock disable by >100ns delay. */ + udelay(1); + + /* Resuscitate crystal clock by setting UTMIP_PHY_XTAL_CLOCKEN */ + setbits_le32(&usbctlr->utmip_misc_cfg1, UTMIP_PHY_XTAL_CLOCKEN); + + /* Finished the per-controller init. */ + + /* De-assert UTMIP_RESET to bring out of reset. */ + clrbits_le32(&usbctlr->susp_ctrl, UTMIP_RESET); + + /* Wait for the phy clock to become valid in 100 ms */ + for (loop_count = 100000; loop_count != 0; loop_count--) { + if (readl(&usbctlr->susp_ctrl) & USB_PHY_CLK_VALID) + break; + udelay(1); + } +} + +static void power_up_port(struct usb_ctlr *usbctlr) +{ + /* Deassert power down state */ + clrbits_le32(&usbctlr->utmip_xcvr_cfg0, UTMIP_FORCE_PD_POWERDOWN | + UTMIP_FORCE_PD2_POWERDOWN | UTMIP_FORCE_PDZI_POWERDOWN); + clrbits_le32(&usbctlr->utmip_xcvr_cfg1, UTMIP_FORCE_PDDISC_POWERDOWN | + UTMIP_FORCE_PDCHRP_POWERDOWN | UTMIP_FORCE_PDDR_POWERDOWN); +} + +static void config_clock(const u32 timing[]) +{ + clock_start_pll(CLOCK_ID_USB, + timing[PARAM_DIVM], timing[PARAM_DIVN], timing[PARAM_DIVP], + timing[PARAM_CPCON], timing[PARAM_LFCON]); +} + +/** + * Add a new USB port to the list of available ports. + * + * @param config USB port configuration + * @return 0 if ok, -1 if error (too many ports) + */ +static int add_port(struct fdt_usb *config) +{ + struct usb_ctlr *usbctlr = config->reg; + + if (port_count == USB_PORTS_MAX) { + debug("tegrausb: Cannot register more than %d ports\n", + USB_PORTS_MAX); + return -1; + } + init_usb_controller(config->periph_id, usbctlr, config->timing); + if (config->utmi) { + /* Disable ICUSB FS/LS transceiver */ + clrbits_le32(&usbctlr->icusb_ctrl, IC_ENB1); + + /* Select UTMI parallel interface */ + clrsetbits_le32(&usbctlr->port_sc1, PTS_MASK, + PTS_UTMI << PTS_SHIFT); + clrbits_le32(&usbctlr->port_sc1, STS); + power_up_port(usbctlr); + } + if (config->host_mode) { + /* Only one host-dev port is supported */ + if (host_dev_ctlr) + return -1; + host_dev_ctlr = &port[port_count]; + } + port[port_count++] = *config; + return 0; +} + +int tegrausb_start_port(unsigned portnum, u32 *hccr, u32 *hcor) +{ + struct usb_ctlr *usbctlr; + + if (portnum >= port_count) + return -1; + tegrausb_stop_port(); + + usbctlr = port[portnum].reg; + *hccr = (u32)&usbctlr->cap_length; + *hcor = (u32)&usbctlr->usb_cmd; + port_current = portnum; + return 0; +} + +int tegrausb_stop_port(void) +{ + struct usb_ctlr *usbctlr; + + if (port_current == -1) + return -1; + + usbctlr = port[port_current].reg; + + /* Stop controller */ + writel(0, &usbctlr->usb_cmd); + udelay(1000); + + /* Initiate controller reset */ + writel(2, &usbctlr->usb_cmd); + udelay(1000); + port_current = -1; + return 0; +} + +int fdt_decode_usb(const void *blob, int node, unsigned osc_frequency_mhz, + struct fdt_usb *config) +{ + int clk_node = 0, rate; + const char *phy; + + /* Find the parameters for our oscillator frequency */ + do { + clk_node = fdt_node_offset_by_compatible(blob, clk_node, + "nvidia,tegra20-usbtiming"); + if (clk_node < 0) { + debug("Cannot find USB timing for clock %u", + osc_frequency_mhz); + return -FDT_ERR_NOTFOUND; + } + rate = fdtdec_get_int(blob, clk_node, "osc-frequency", 0); + } while (rate != osc_frequency_mhz); + + config->reg = (struct usb_ctlr *)fdtdec_get_addr(blob, node, "reg"); + config->host_mode = fdtdec_get_bool(blob, node, "support-host-mode"); + phy = fdt_getprop(blob, node, "phy_type", NULL); + config->utmi = phy && 0 == strcmp("utmi", phy); + config->enabled = fdtdec_get_is_enabled(blob, node); + config->periph_id = fdtdec_get_int(blob, node, "periph-id", -1); + if (config->periph_id == -1) + return -FDT_ERR_NOTFOUND; + fdtdec_decode_gpio(blob, node, "nvidia,vbus-gpio", &config->vbus_gpio); + + return fdtdec_get_int_array(blob, clk_node, "timing", config->timing, + PARAM_COUNT); +} + +int board_usb_init(const void *blob) +{ + struct fdt_usb config; + int clk_done = 0; + int node, upto = 0; + unsigned osc_freq = clock_get_rate(CLOCK_ID_OSC); + + do { + node = fdtdec_next_alias(blob, "usb", + COMPAT_NVIDIA_TEGRA20_USB, &upto); + if (node < 0) { + debug("Cannot find usb%d alias in fdt\n", upto); + break; + } + if (fdt_decode_usb(blob, node, osc_freq, &config)) { + debug("Cannot decode USB node %s\n", + fdt_get_name(blob, node, NULL)); + return -1; + } + if (!config.enabled) { + debug("Skipping USB node %s since it is disabled\n", + fdt_get_name(blob, node, NULL)); + continue; + } + + /* The first port we find gets to set the clocks */ + if (!clk_done) { + config_clock(config.timing); + clk_done = 1; + } + if (add_port(&config)) + return -1; + } while (node); + usb_set_host_mode(); + port_current = -1; + return 0; +} diff --git a/arch/arm/include/asm/arch-tegra2/tegra2.h b/arch/arm/include/asm/arch-tegra2/tegra2.h index 8941443..baae2eb 100644 --- a/arch/arm/include/asm/arch-tegra2/tegra2.h +++ b/arch/arm/include/asm/arch-tegra2/tegra2.h @@ -41,6 +41,8 @@ #define TEGRA2_SPI_BASE (NV_PA_APB_MISC_BASE + 0xC380) #define NV_PA_PMC_BASE 0x7000E400 #define NV_PA_CSITE_BASE 0x70040000 +#define TEGRA_USB1_BASE 0xC5000000 +#define TEGRA_USB3_BASE 0xC5008000
#define TEGRA2_SDRC_CS0 NV_PA_SDRAM_BASE #define LOW_LEVEL_SRAM_STACK 0x4000FFFC diff --git a/arch/arm/include/asm/arch-tegra2/usb.h b/arch/arm/include/asm/arch-tegra2/usb.h new file mode 100644 index 0000000..0a3056d --- /dev/null +++ b/arch/arm/include/asm/arch-tegra2/usb.h @@ -0,0 +1,255 @@ +/* + * Copyright (c) 2011 The Chromium OS Authors. + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef _TEGRA_USB_H_ +#define _TEGRA_USB_H_ + + +/* USB Controller (USBx_CONTROLLER_) regs */ +struct usb_ctlr { + /* 0x000 */ + uint id; + uint reserved0; + uint host; + uint device; + + /* 0x010 */ + uint txbuf; + uint rxbuf; + uint reserved1[2]; + + /* 0x020 */ + uint reserved2[56]; + + /* 0x100 */ + u16 cap_length; + u16 hci_version; + uint hcs_params; + uint hcc_params; + uint reserved3[5]; + + /* 0x120 */ + uint dci_version; + uint dcc_params; + uint reserved4[6]; + + /* 0x140 */ + uint usb_cmd; + uint usb_sts; + uint usb_intr; + uint frindex; + + /* 0x150 */ + uint reserved5; + uint periodic_list_base; + uint async_list_addr; + uint async_tt_sts; + + /* 0x160 */ + uint burst_size; + uint tx_fill_tuning; + uint reserved6; /* is this port_sc1 on some controllers? */ + uint icusb_ctrl; + + /* 0x170 */ + uint ulpi_viewport; + uint reserved7; + uint endpt_nak; + uint endpt_nak_enable; + + /* 0x180 */ + uint reserved; + uint port_sc1; + uint reserved8[6]; + + /* 0x1a0 */ + uint reserved9; + uint otgsc; + uint usb_mode; + uint endpt_setup_stat; + + /* 0x1b0 */ + uint reserved10[20]; + + /* 0x200 */ + uint reserved11[0x80]; + + /* 0x400 */ + uint susp_ctrl; + uint phy_vbus_sensors; + uint phy_vbus_wakeup_id; + uint phy_alt_vbus_sys; + + /* 0x410 */ + uint usb1_legacy_ctrl; + uint reserved12[3]; + + /* 0x420 */ + uint reserved13[56]; + + /* 0x500 */ + uint reserved14[64 * 3]; + + /* 0x800 */ + uint utmip_pll_cfg0; + uint utmip_pll_cfg1; + uint utmip_xcvr_cfg0; + uint utmip_bias_cfg0; + + /* 0x810 */ + uint utmip_hsrx_cfg0; + uint utmip_hsrx_cfg1; + uint utmip_fslsrx_cfg0; + uint utmip_fslsrx_cfg1; + + /* 0x820 */ + uint utmip_tx_cfg0; + uint utmip_misc_cfg0; + uint utmip_misc_cfg1; + uint utmip_debounce_cfg0; + + /* 0x830 */ + uint utmip_bat_chrg_cfg0; + uint utmip_spare_cfg0; + uint utmip_xcvr_cfg1; + uint utmip_bias_cfg1; +}; + + +/* USB1_LEGACY_CTRL */ +#define USB1_NO_LEGACY_MODE 1 + +#define VBUS_SENSE_CTL_SHIFT 1 +#define VBUS_SENSE_CTL_MASK (3 << VBUS_SENSE_CTL_SHIFT) +#define VBUS_SENSE_CTL_VBUS_WAKEUP 0 +#define VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP 1 +#define VBUS_SENSE_CTL_AB_SESS_VLD 2 +#define VBUS_SENSE_CTL_A_SESS_VLD 3 + +/* USBx_IF_USB_SUSP_CTRL_0 */ +#define UTMIP_PHY_ENB (1 << 12) +#define UTMIP_RESET (1 << 11) +#define USB_PHY_CLK_VALID (1 << 7) + +/* USBx_UTMIP_MISC_CFG1 */ +#define UTMIP_PLLU_STABLE_COUNT_SHIFT 6 +#define UTMIP_PLLU_STABLE_COUNT_MASK \ + (0xfff << UTMIP_PLLU_STABLE_COUNT_SHIFT) +#define UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT 18 +#define UTMIP_PLL_ACTIVE_DLY_COUNT_MASK \ + (0x1f << UTMIP_PLL_ACTIVE_DLY_COUNT_SHIFT) +#define UTMIP_PHY_XTAL_CLOCKEN (1 << 30) + +/* USBx_UTMIP_PLL_CFG1_0 */ +#define UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT 27 +#define UTMIP_PLLU_ENABLE_DLY_COUNT_MASK \ + (0xf << UTMIP_PLLU_ENABLE_DLY_COUNT_SHIFT) +#define UTMIP_XTAL_FREQ_COUNT_SHIFT 0 +#define UTMIP_XTAL_FREQ_COUNT_MASK 0xfff + +/* USBx_UTMIP_BIAS_CFG1_0 */ +#define UTMIP_BIAS_PDTRK_COUNT_SHIFT 3 +#define UTMIP_BIAS_PDTRK_COUNT_MASK \ + (0x1f << UTMIP_BIAS_PDTRK_COUNT_SHIFT) +#define UTMIP_BIAS_PDTRK_COUNT_SHIFT 3 +#define UTMIP_BIAS_PDTRK_COUNT_MASK \ + (0x1f << UTMIP_BIAS_PDTRK_COUNT_SHIFT) + +#define UTMIP_DEBOUNCE_CFG0_SHIFT 0 +#define UTMIP_DEBOUNCE_CFG0_MASK 0xffff + +/* USBx_UTMIP_TX_CFG0_0 */ +#define UTMIP_FS_PREAMBLE_J (1 << 19) + +/* USBx_UTMIP_BAT_CHRG_CFG0_0 */ +#define UTMIP_PD_CHRG 1 + +/* USBx_UTMIP_XCVR_CFG0_0 */ +#define UTMIP_XCVR_LSBIAS_SE (1 << 21) + +/* USBx_UTMIP_SPARE_CFG0_0 */ +#define FUSE_SETUP_SEL (1 << 3) + +/* USBx_UTMIP_HSRX_CFG0_0 */ +#define UTMIP_IDLE_WAIT_SHIFT 15 +#define UTMIP_IDLE_WAIT_MASK (0x1f << UTMIP_IDLE_WAIT_SHIFT) +#define UTMIP_ELASTIC_LIMIT_SHIFT 10 +#define UTMIP_ELASTIC_LIMIT_MASK \ + (0x1f << UTMIP_ELASTIC_LIMIT_SHIFT) + +/* USBx_UTMIP_HSRX_CFG0_1 */ +#define UTMIP_HS_SYNC_START_DLY_SHIFT 1 +#define UTMIP_HS_SYNC_START_DLY_MASK \ + (0xf << UTMIP_HS_SYNC_START_DLY_SHIFT) + +/* USBx_CONTROLLER_2_USB2D_ICUSB_CTRL_0 */ +#define IC_ENB1 (1 << 3) + +/* SB2_CONTROLLER_2_USB2D_PORTSC1_0 */ +#define PTS_SHIFT 30 +#define PTS_MASK (3 << PTS_SHIFT) +#define PTS_UTMI 0 +#define PTS_RESERVED 1 +#define PTS_ULP 2 +#define PTS_ICUSB_SER 3 + +#define STS (1 << 29) + +/* USBx_UTMIP_XCVR_CFG0_0 */ +#define UTMIP_FORCE_PD_POWERDOWN (1 << 14) +#define UTMIP_FORCE_PD2_POWERDOWN (1 << 16) +#define UTMIP_FORCE_PDZI_POWERDOWN (1 << 18) + +/* USBx_UTMIP_XCVR_CFG1_0 */ +#define UTMIP_FORCE_PDDISC_POWERDOWN (1 << 0) +#define UTMIP_FORCE_PDCHRP_POWERDOWN (1 << 2) +#define UTMIP_FORCE_PDDR_POWERDOWN (1 << 4) + +/* USB3_IF_USB_PHY_VBUS_SENSORS_0 */ +#define VBUS_VLD_STS (1 << 26) + + +/* Change the USB host port into host mode */ +void usb_set_host_mode(void); + +/* Setup USB on the board */ +int board_usb_init(const void *blob); + +/** + * Start up the given port number (ports are numbered from 0 on each board). + * This returns values for the appropriate hccr and hcor addresses to use for + * USB EHCI operations. + * + * @param portnum port number to start + * @param hccr returns start address of EHCI HCCR registers + * @param hcor returns start address of EHCI HCOR registers + * @return 0 if ok, -1 on error (generally invalid port number) + */ +int tegrausb_start_port(unsigned portnum, u32 *hccr, u32 *hcor); + +/** + * Stop the current port + * + * @return 0 if ok, -1 if no port was active + */ +int tegrausb_stop_port(void); + +#endif /* _TEGRA_USB_H_ */ diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 09abb75..39134ff 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -46,6 +46,7 @@ COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o COBJS-$(CONFIG_USB_EHCI_KIRKWOOD) += ehci-kirkwood.o COBJS-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o +COBJS-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o COBJS-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
COBJS := $(COBJS-y) diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c new file mode 100644 index 0000000..3a48c26 --- /dev/null +++ b/drivers/usb/host/ehci-tegra.c @@ -0,0 +1,63 @@ +/* + * Copyright (c) 2009 NVIDIA Corporation + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <usb.h> + +#include "ehci.h" +#include "ehci-core.h" + +#include <asm/errno.h> +#include <asm/arch/usb.h> + + +/* + * Create the appropriate control structures to manage + * a new EHCI host controller. + */ +int ehci_hcd_init(void) +{ + u32 our_hccr, our_hcor; + + /* + * Select the first port, as we don't have a way of selecting others + * yet + */ + if (tegrausb_start_port(0, &our_hccr, &our_hcor)) + return -1; + + hccr = (struct ehci_hccr *)our_hccr; + hcor = (struct ehci_hcor *)our_hcor; + + return 0; +} + +/* + * Destroy the appropriate control structures corresponding + * the the EHCI host controller. + */ +int ehci_hcd_stop(void) +{ + usb_set_host_mode(); + tegrausb_stop_port(); + return 0; +} diff --git a/include/fdtdec.h b/include/fdtdec.h index 57db42b..9871b81 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -57,6 +57,7 @@ struct fdt_memory { */ enum fdt_compat_id { COMPAT_UNKNOWN, + COMPAT_NVIDIA_TEGRA20_USB, /* Tegra2 USB port */
COMPAT_COUNT, }; diff --git a/lib/fdtdec.c b/lib/fdtdec.c index 8eed752..509b81f 100644 --- a/lib/fdtdec.c +++ b/lib/fdtdec.c @@ -37,6 +37,7 @@ DECLARE_GLOBAL_DATA_PTR; #define COMPAT(id, name) name static const char * const compat_names[COMPAT_COUNT] = { COMPAT(UNKNOWN, "<none>"), + COMPAT(NVIDIA_TEGRA20_USB, "nvidia,tegra20-ehci"), };
/**