The SPI and NAND board variants never went into production. Drop those board variants.
Signed-off-by: Bernhard Messerklinger bernhard.messerklinger@br-automation.com ---
arch/arm/dts/Makefile | 2 - arch/arm/dts/am335x-brppt1-nand.dts | 374 --------------------------- arch/arm/dts/am335x-brppt1-spi.dts | 377 ---------------------------- board/BuR/brppt1/board.c | 4 +- board/BuR/brppt1/mux.c | 39 +-- configs/brppt1_nand_defconfig | 122 --------- configs/brppt1_spi_defconfig | 130 ---------- include/configs/brppt1.h | 64 +---- 8 files changed, 7 insertions(+), 1105 deletions(-) delete mode 100644 arch/arm/dts/am335x-brppt1-nand.dts delete mode 100644 arch/arm/dts/am335x-brppt1-spi.dts delete mode 100644 configs/brppt1_nand_defconfig delete mode 100644 configs/brppt1_spi_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 7330121dba..5bff2e65b7 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -388,8 +388,6 @@ dtb-$(CONFIG_AM33XX) += \ am335x-boneblack-wireless.dtb \ am335x-boneblue.dtb \ am335x-brppt1-mmc.dtb \ - am335x-brppt1-nand.dtb \ - am335x-brppt1-spi.dtb \ am335x-brxre1.dtb \ am335x-brsmarc1.dtb \ am335x-draco.dtb \ diff --git a/arch/arm/dts/am335x-brppt1-nand.dts b/arch/arm/dts/am335x-brppt1-nand.dts deleted file mode 100644 index 67c609739f..0000000000 --- a/arch/arm/dts/am335x-brppt1-nand.dts +++ /dev/null @@ -1,374 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2018 B&R Industrial Automation GmbH - * http://www.br-automation.com - * - */ -/dts-v1/; - -#include "am33xx.dtsi" - -/ { - model = "BRPPT1 (NAND) Panel"; - compatible = "ti,am33xx"; - - fset: factory-settings { - bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; - version = <0x0100>; - order-no = "6PPT30 (NAND)"; - hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; - serial-no = "0"; - device-id = <0x0>; - parent-id = <0x0>; - hw-variant = <0x1>; - }; - - aliases { - ds1bkl0 = &pwmbacklight; - ds1bkl1 = &tps_bl; - ds1timing = &timing0; - ds1ctrl = &lcdc; - gpmc = &gpmc; - mmc = &mmc2; - fset = &fset; - }; - - chosen { - bootargs = "console=ttyO0,115200 earlyprintk"; - stdout-path = &uart0; - }; - - memory { - device_type = "memory"; - reg = <0x80000000 0x10000000>; /* 256 MB */ - }; - - panel { - status = "disabled"; - - compatible = "ti,tilcdc,panel"; - enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; - - backlight = <&pwmbacklight>; - bkl-pwm = <&pwmbacklight>; - bkl-tps = <&tps_bl>; - - panel-info { - ac-bias = <255>; - ac-bias-intrpt = <0>; - dma-burst-sz = <16>; - bpp = <32>; - fdd = <0x80>; - sync-edge = <0>; - sync-ctrl = <1>; - raster-order = <0>; - fifo-th = <0>; - }; - - display-timings { - native-mode = <&timing0>; - timing0: lcd { - clock-frequency = <32000000>; - hactive = <800>; - vactive = <480>; - hfront-porch = <2>; - hback-porch = <192>; - hsync-len = <1>; - vfront-porch = <20>; - vback-porch = <2>; - vsync-len = <1>; - hsync-active = <1>; - vsync-active = <1>; - pupdelay = <10>; - pondelay = <10>; - }; - }; - }; - - vmmcsd_fixed: fixedregulator@0 { - compatible = "regulator-fixed"; - regulator-name = "vmmcsd_fixed"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - pwm0: omap-pwm@timer5 { - compatible = "ti,omap-dmtimer-pwm"; - ti,timers = <&timer5>; - #pwm-cells = <3>; - }; - - pwm1: omap-pwm@timer6 { - compatible = "ti,omap-dmtimer-pwm"; - ti,timers = <&timer6>; - #pwm-cells = <3>; - }; - - beeper: pwm-beep { - compatible = "pwm-beeper"; - pwms = <&pwm0 0 0 0>; - }; - - pwmbacklight: pwm-bkl { - compatible = "pwm-backlight"; - pwms = <&pwm1 0 5000000 0>; - - default-brightness-level = <255>; - brightness-levels = <0 16 32 64 128 170 202 234 255>; - - power-supply = <&vmmcsd_fixed>; - enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - }; -}; - -&uart0 { /* console uart */ - u-boot,dm-spl; - status = "okay"; -}; - -&uart1 { - status = "okay"; -}; - -&i2c0 { - u-boot,dm-spl; - status = "okay"; - clock-frequency = <400000>; - - tps: tps@24 { /* PMIC controller */ - u-boot,dm-spl; - reg = <0x24>; - compatible = "ti,tps65217"; - - tps_bl: backlight { - compatible = "ti,tps65217-bl"; - isel = <1>; /* 1 - ISET1, 2 ISET2 */ - fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */ - default-brightness = <50>; - }; - }; -}; - -&i2c2 { - status = "okay"; - clock-frequency = <100000>; -}; - -&edma { - status = "okay"; -}; - -&cppi41dma { - status = "okay"; -}; - -&usb { - status = "okay"; -}; - -&usb_ctrl_mod { - status = "okay"; -}; - -&usb0_phy { - status = "okay"; -}; - -&usb1_phy { - status = "okay"; -}; - -&usb0 { - status = "okay"; - dr_mode = "host"; -}; - -&usb1 { - status = "okay"; - dr_mode = "host"; -}; - -&davinci_mdio { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <1>; - }; - - phy1: ethernet-phy@1 { - reg = <2>; - }; -}; - -&mac { - dual_emac; - status = "okay"; -}; - -&cpsw_emac0 { - phy-handle = <&phy0>; - dual_emac_res_vlan = <1>; - phy-mode = "mii"; -}; - -&cpsw_emac1 { - phy-handle = <&phy1>; - dual_emac_res_vlan = <2>; - phy-mode = "mii"; -}; - -&mmc2 { - vmmc-supply = <&vmmcsd_fixed>; - bus-width = <0x4>; - ti,non-removable; - ti,needs-special-hs-handling; - ti,vcc-aux-disable-is-sleep; - status = "disabled"; -}; - -&l4_per { - - segment@300000 { - - target-module@e000 { - u-boot,dm-pre-reloc; - - lcdc: lcdc@0 { - u-boot,dm-pre-reloc; - status = "disabled"; - }; - }; - }; -}; - -&elm { - status = "okay"; -}; - -&sham { - status = "okay"; -}; - -&aes { - status = "okay"; -}; - -&gpio0 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&gpio1 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&gpio2 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&gpio3 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&wdt2 { - ti,no-reset-on-init; - ti,no-idle-on-init; -}; - -&tscadc { - status = "okay"; - tsc { - ti,wires = <4>; - ti,x-plate-resistance = <200>; - ti,zx-cutoff-ratio = <40>; - ti,min_deviation = <60>; - ti,max_deviation = <600>; - ti,coordinate-readouts = <5>; - ti,wire-config = <0x00 0x11 0x22 0x33>; - - bnr-buttons { - Home-Button {}; - }; - }; - - adc { - ti,adc-channels = <5 6 7>; - }; -}; - -&gpmc { - u-boot,dm-spl; - status = "okay"; - pinctrl-names = "default"; - ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ - nand@0,0 { - compatible = "ti,omap2-nand"; - reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ - interrupt-parent = <&gpmc>; - rb-gpios = <&gpmc 1 GPIO_ACTIVE_HIGH>; /* gpmc_wait1 */ - ti,nand-ecc-opt = "bch8"; - ti,elm-id = <&elm>; - nand-bus-width = <8>; - gpmc,device-width = <1>; - gpmc,sync-clk-ps = <0>; - gpmc,cs-on-ns = <0>; - gpmc,cs-rd-off-ns = <44>; - gpmc,cs-wr-off-ns = <44>; - gpmc,adv-on-ns = <6>; - gpmc,adv-rd-off-ns = <34>; - gpmc,adv-wr-off-ns = <44>; - gpmc,we-on-ns = <0>; - gpmc,we-off-ns = <40>; - gpmc,oe-on-ns = <0>; - gpmc,oe-off-ns = <54>; - gpmc,access-ns = <64>; - gpmc,rd-cycle-ns = <82>; - gpmc,wr-cycle-ns = <82>; - gpmc,wait-on-read = "true"; - gpmc,wait-on-write = "true"; - gpmc,bus-turnaround-ns = <0>; - gpmc,cycle2cycle-delay-ns = <0>; - gpmc,clk-activation-ns = <0>; - gpmc,wait-monitoring-ns = <0>; - gpmc,wr-access-ns = <40>; - gpmc,wr-data-mux-bus-ns = <0>; - gpmc,wait-pin = <1>; - #address-cells = <1>; - #size-cells = <1>; - partition@0 { - label = "NAND.MLO"; - reg = <0x00000000 0x000020000>; - }; - partition@1 { - label = "NAND.cfgscr"; - reg = <0x00020000 0x00020000>; - }; - partition@2 { - label = "NAND.dtb"; - reg = <0x00040000 0x00020000>; - }; - partition@3 { - label = "NAND.u-boot-env"; - reg = <0x00060000 0x00020000>; - }; - partition@4 { - label = "NAND.u-boot"; - reg = <0x00080000 0x00080000>; - }; - partition@5 { - label = "NAND.kernel"; - reg = <0x00100000 0x00400000>; - }; - partition@6 { - label = "NAND.rootfs"; - reg = <0x00500000 0x08000000>; - }; - partition@7 { - label = "NAND.user"; - reg = <0x08500000 0x17b00000>; - }; - }; -}; diff --git a/arch/arm/dts/am335x-brppt1-spi.dts b/arch/arm/dts/am335x-brppt1-spi.dts deleted file mode 100644 index ce3dce204d..0000000000 --- a/arch/arm/dts/am335x-brppt1-spi.dts +++ /dev/null @@ -1,377 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2018 B&R Industrial Automation GmbH - * http://www.br-automation.com - * - */ -/dts-v1/; - -#include "am33xx.dtsi" - -/ { - model = "BRPPT1 (MMC) Panel"; - compatible = "ti,am33xx"; - - fset: factory-settings { - bl-version = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; - version = <0x0100>; - order-no = "6PPT30 (SPI)"; - hw-revision = "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890"; - serial-no = "0"; - device-id = <0x0>; - parent-id = <0x0>; - hw-variant = <0x1>; - }; - - aliases { - ds1bkl0 = &pwmbacklight; - ds1bkl1 = &tps_bl; - ds1timing = &timing0; - ds1ctrl = &lcdc; - gpmc = &gpmc; - mmc = &mmc2; - spi0 = &spi0; - fset = &fset; - }; - - chosen { - bootargs = "console=ttyO0,115200 earlyprintk"; - stdout-path = &uart0; - }; - - memory { - device_type = "memory"; - reg = <0x80000000 0x10000000>; /* 256 MB */ - }; - - panel { - status = "disabled"; - - compatible = "ti,tilcdc,panel"; - enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; - - backlight = <&pwmbacklight>; - bkl-pwm = <&pwmbacklight>; - bkl-tps = <&tps_bl>; - - panel-info { - ac-bias = <255>; - ac-bias-intrpt = <0>; - dma-burst-sz = <16>; - bpp = <32>; - fdd = <0x80>; - sync-edge = <0>; - sync-ctrl = <1>; - raster-order = <0>; - fifo-th = <0>; - }; - - display-timings { - native-mode = <&timing0>; - timing0: lcd { - clock-frequency = <32000000>; - hactive = <800>; - vactive = <480>; - hfront-porch = <2>; - hback-porch = <192>; - hsync-len = <1>; - vfront-porch = <20>; - vback-porch = <2>; - vsync-len = <1>; - hsync-active = <1>; - vsync-active = <1>; - pupdelay = <10>; - pondelay = <10>; - }; - }; - }; - - vmmcsd_fixed: fixedregulator@0 { - compatible = "regulator-fixed"; - regulator-name = "vmmcsd_fixed"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - pwm0: omap-pwm@timer5 { - compatible = "ti,omap-dmtimer-pwm"; - ti,timers = <&timer5>; - #pwm-cells = <3>; - }; - - pwm1: omap-pwm@timer6 { - compatible = "ti,omap-dmtimer-pwm"; - ti,timers = <&timer6>; - #pwm-cells = <3>; - }; - - beeper: pwm-beep { - compatible = "pwm-beeper"; - pwms = <&pwm0 0 0 0>; - }; - - pwmbacklight: pwm-bkl { - compatible = "pwm-backlight"; - pwms = <&pwm1 0 5000000 0>; - - default-brightness-level = <255>; - brightness-levels = <0 16 32 64 128 170 202 234 255>; - - power-supply = <&vmmcsd_fixed>; - enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - }; -}; - -&uart0 { /* console uart */ - u-boot,dm-spl; - status = "okay"; -}; - -&uart1 { - status = "okay"; -}; - -&i2c0 { - u-boot,dm-spl; - status = "okay"; - clock-frequency = <400000>; - - tps: tps@24 { /* PMIC controller */ - u-boot,dm-spl; - reg = <0x24>; - compatible = "ti,tps65217"; - - tps_bl: backlight { - compatible = "ti,tps65217-bl"; - isel = <1>; /* 1 - ISET1, 2 ISET2 */ - fdim = <1000>; /* TPS65217_BL_FDIM_1kHZ */ - default-brightness = <50>; - }; - }; -}; - -&i2c2 { - status = "okay"; - clock-frequency = <100000>; -}; - -&spi0 { - u-boot,dm-spl; - status = "okay"; - - cs-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>, - <&gpio0 6 GPIO_ACTIVE_HIGH>, - <0>, - <0>; - - spi-max-frequency = <24000000>; - - spi_flash: spiflash@0 { - u-boot,dm-spl; - u-boot,dm-pre-reloc; - compatible = "spidev", "jedec,spi-nor"; - spi-max-frequency = <24000000>; - reg = <0>; - }; -}; - -&edma { - status = "okay"; -}; - -&cppi41dma { - status = "okay"; -}; - -&usb { - status = "okay"; -}; - -&usb_ctrl_mod { - status = "okay"; -}; - -&usb0_phy { - status = "okay"; -}; - -&usb1_phy { - status = "okay"; -}; - -&usb0 { - status = "okay"; - dr_mode = "host"; -}; - -&usb1 { - status = "okay"; - dr_mode = "host"; -}; - -&davinci_mdio { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <1>; - }; - - phy1: ethernet-phy@1 { - reg = <2>; - }; -}; - -&mac { - status = "okay"; -}; - -&cpsw_emac0 { - phy-handle = <&phy0>; - dual_emac_res_vlan = <1>; - phy-mode = "mii"; -}; - -&cpsw_emac1 { - phy-handle = <&phy1>; - dual_emac_res_vlan = <2>; - phy-mode = "mii"; -}; - -&mmc1 { - u-boot,dm-spl; - vmmc-supply = <&vmmcsd_fixed>; - bus-width = <0x4>; - ti,non-removable; - ti,needs-special-hs-handling; - ti,vcc-aux-disable-is-sleep; - status = "okay"; -}; - -&mmc2 { - u-boot,dm-spl; - vmmc-supply = <&vmmcsd_fixed>; - bus-width = <0x8>; - ti,non-removable; - ti,needs-special-hs-handling; - ti,vcc-aux-disable-is-sleep; - status = "okay"; -}; - -&l4_per { - - segment@300000 { - - target-module@e000 { - u-boot,dm-pre-reloc; - - lcdc: lcdc@0 { - u-boot,dm-pre-reloc; - status = "disabled"; - }; - }; - }; -}; - -&elm { - status = "okay"; -}; - -&sham { - status = "okay"; -}; - -&aes { - status = "okay"; -}; - -&gpio0 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&gpio1 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&gpio2 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&gpio3 { - u-boot,dm-spl; - ti,no-reset-on-init; -}; - -&wdt2 { - ti,no-reset-on-init; - ti,no-idle-on-init; -}; - -&tscadc { - status = "okay"; - tsc { - ti,wires = <4>; - ti,x-plate-resistance = <200>; - ti,zx-cutoff-ratio = <40>; - ti,min_deviation = <60>; - ti,max_deviation = <600>; - ti,coordinate-readouts = <5>; - ti,wire-config = <0x00 0x11 0x22 0x33>; - - bnr-buttons { - Home-Button {}; - }; - }; - - adc { - ti,adc-channels = <5 6 7>; - }; -}; - -&timer6 { /* used for cpsw end device */ - status = "okay"; - ti,no-reset-on-init; - ti,no-idle-on-init; -}; - -&timer7 { /* used for cpsw end device */ - status = "okay"; - ti,no-reset-on-init; - ti,no-idle-on-init; -}; - -&wdt2 { - status = "okay"; - ti,no-reset-on-init; - ti,no-idle-on-init; -}; - -&epwmss0 { - status = "okay"; -}; - -&tscadc { - status = "okay"; -}; - -&dcan0 { - status = "okay"; -}; - -&dcan1 { - status = "okay"; -}; - -&sham { - status = "disabled"; -}; - -&aes { - status = "disabled"; -}; - -&rng { - status = "disabled"; -}; diff --git a/board/BuR/brppt1/board.c b/board/BuR/brppt1/board.c index 7df37e4e66..c8dc186cdd 100644 --- a/board/BuR/brppt1/board.c +++ b/board/BuR/brppt1/board.c @@ -151,9 +151,7 @@ int board_init(void) hw_watchdog_init(); #endif gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; -#ifdef CONFIG_MTD_RAW_NAND - gpmc_init(); -#endif + return 0; }
diff --git a/board/BuR/brppt1/mux.c b/board/BuR/brppt1/mux.c index b863d37335..5d2c7a201e 100644 --- a/board/BuR/brppt1/mux.c +++ b/board/BuR/brppt1/mux.c @@ -26,6 +26,7 @@ static struct module_pin_mux uart0_pin_mux[] = { {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, {-1}, }; + static struct module_pin_mux uart1_pin_mux[] = { /* UART1_RTS as I2C2-SCL */ {OFFSET(uart1_rtsn), (MODE(3) | PULLUDEN | PULLUP_EN | RXACTIVE)}, @@ -37,7 +38,7 @@ static struct module_pin_mux uart1_pin_mux[] = { {OFFSET(uart1_txd), (MODE(0) | PULLUDEN)}, {-1}, }; -#ifdef CONFIG_MMC + static struct module_pin_mux mmc1_pin_mux[] = { {OFFSET(gpmc_ad7), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT7 */ {OFFSET(gpmc_ad6), (MODE(1) | RXACTIVE | PULLUP_EN)}, /* MMC1_DAT6 */ @@ -54,7 +55,7 @@ static struct module_pin_mux mmc1_pin_mux[] = { {OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},/* MMC1_CD */ {-1}, }; -#endif + static struct module_pin_mux i2c0_pin_mux[] = { /* I2C_DATA */ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)}, @@ -118,26 +119,7 @@ static struct module_pin_mux mii2_pin_mux[] = { {OFFSET(gpmc_be1n), (MODE(1) | RXACTIVE)},/* MII1_COL */ {-1}, }; -#ifdef CONFIG_MTD_RAW_NAND -static struct module_pin_mux nand_pin_mux[] = { - {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */ - {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */ - {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */ - {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */ - {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */ - {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */ - {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */ - {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */ - {OFFSET(gpmc_clk), (MODE(2) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */ - {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */ - {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */ - {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */ - {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */ - {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */ - {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */ - {-1}, -}; -#endif + static struct module_pin_mux gpIOs[] = { /* GPIO0_6 (SPI0_CS1) - 3v3_PWR_nEN (Display Power Supply) */ {OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)}, @@ -180,14 +162,6 @@ static struct module_pin_mux gpIOs[] = { {OFFSET(mcasp0_axr0), (MODE(7) | PULLUDDIS) }, /* GPIO3_17 (MCASP0_AHCLKR) - ETH2_LEDY */ {OFFSET(mcasp0_ahclkr), (MODE(7) | PULLUDDIS) }, -#ifndef CONFIG_MTD_RAW_NAND - /* GPIO2_3 - NAND_OE */ - {OFFSET(gpmc_oen_ren), (MODE(7) | PULLDOWN_EN | RXACTIVE)}, - /* GPIO2_4 - NAND_WEN */ - {OFFSET(gpmc_wen), (MODE(7) | PULLDOWN_EN | RXACTIVE)}, - /* GPIO2_5 - NAND_BE_CLE */ - {OFFSET(gpmc_be0n_cle), (MODE(7) | PULLDOWN_EN | RXACTIVE)}, -#endif {-1}, };
@@ -222,7 +196,6 @@ static struct module_pin_mux lcd_pin_mux[] = { {OFFSET(lcd_hsync), (MODE(0) | PULLUDDIS)}, /* LCD-HSync */ {OFFSET(lcd_ac_bias_en), (MODE(0) | PULLUDDIS)},/* LCD-DE */ {OFFSET(lcd_pclk), (MODE(0) | PULLUDDIS)}, /* LCD-CLK */ - {-1}, };
@@ -241,11 +214,7 @@ void enable_board_pin_mux(void) configure_module_pin_mux(i2c0_pin_mux); configure_module_pin_mux(mii1_pin_mux); configure_module_pin_mux(mii2_pin_mux); -#ifdef CONFIG_MTD_RAW_NAND - configure_module_pin_mux(nand_pin_mux); -#elif defined(CONFIG_MMC) configure_module_pin_mux(mmc1_pin_mux); -#endif configure_module_pin_mux(spi0_pin_mux); configure_module_pin_mux(lcd_pin_mux); configure_module_pin_mux(uart1_pin_mux); diff --git a/configs/brppt1_nand_defconfig b/configs/brppt1_nand_defconfig deleted file mode 100644 index c5981bad49..0000000000 --- a/configs/brppt1_nand_defconfig +++ /dev/null @@ -1,122 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_OMAP2PLUS=y -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_SPL_GPIO=y -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x10000 -CONFIG_ENV_OFFSET=0x60000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-nand" -CONFIG_AM33XX=y -CONFIG_TARGET_BRPPT1=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL=y -CONFIG_SYS_LOAD_ADDR=0x80000000 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 -# CONFIG_EXPERT is not set -# CONFIG_FIT is not set -CONFIG_OF_BOARD_SETUP=y -CONFIG_BOOTDELAY=0 -CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="run b_default" -CONFIG_USE_PREBOOT=y -CONFIG_PREBOOT="run cfgscr; run brdefaultip" -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_CPUINFO is not set -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_SPL_SYS_MALLOC_SIMPLE=y -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_SPL_MALLOC_SIZE=0x500000 -# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set -CONFIG_SPL_I2C=y -CONFIG_SPL_NAND_DRIVERS=y -CONFIG_SPL_NAND_ECC=y -CONFIG_SPL_NAND_BASE=y -CONFIG_SPL_POWER=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SPL_YMODEM_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_CBSIZE=512 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_SYS_BOOTM_LEN=0x2000000 -# CONFIG_CMD_IMI is not set -# CONFIG_CMD_XIMG is not set -# CONFIG_CMD_EDITENV is not set -# CONFIG_CMD_CRC32 is not set -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_GPIO=y -CONFIG_CMD_I2C=y -# CONFIG_CMD_LOADS is not set -CONFIG_CMD_NAND=y -CONFIG_CMD_PART=y -CONFIG_CMD_USB=y -# CONFIG_CMD_ITEST is not set -CONFIG_CMD_DHCP=y -CONFIG_BOOTP_MAY_FAIL=y -# CONFIG_CMD_NFS is not set -CONFIG_SYS_DISABLE_AUTOLOAD=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BOOTCOUNT=y -CONFIG_CMD_CACHE=y -CONFIG_CMD_TIME=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y -CONFIG_CMD_MTDPARTS=y -CONFIG_MTDIDS_DEFAULT="nand0=omap2-nand.0" -CONFIG_MTDPARTS_DEFAULT="mtdparts=omap2-nand.0:128k(MLO),128k(cfgscr),128k(dtb),128k(u-boot-env),512k(u-boot),4m(kernel),128m(rootfs),-(user)" -# CONFIG_SPL_DOS_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_SPL_OF_CONTROL=y -CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas " -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_VERSION_VARIABLE=y -CONFIG_NET_RETRY_COUNT=10 -CONFIG_BOOTP_SEND_HOSTNAME=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_NETCONSOLE=y -CONFIG_DM=y -CONFIG_SPL_DM=y -CONFIG_SPL_DM_SEQ_ALIAS=y -# CONFIG_OF_TRANSLATE is not set -CONFIG_BOOTCOUNT_LIMIT=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_MISC=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_MTD_RAW_NAND=y -CONFIG_SYS_NAND_BLOCK_SIZE=0x20000 -CONFIG_SYS_NAND_PAGE_COUNT=0x40 -CONFIG_SYS_NAND_PAGE_SIZE=0x800 -CONFIG_SYS_NAND_OOBSIZE=0x40 -CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y -CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 -CONFIG_PHY_NATSEMI=y -CONFIG_DRIVER_TI_CPSW=y -CONFIG_DM_PMIC=y -# CONFIG_SPL_DM_PMIC is not set -CONFIG_PMIC_TPS65217=y -CONFIG_DM_SERIAL=y -CONFIG_USB=y -CONFIG_USB_MUSB_HOST=y -CONFIG_USB_MUSB_GADGET=y -CONFIG_USB_MUSB_TI=y -CONFIG_USB_STORAGE=y -CONFIG_USB_GADGET=y -CONFIG_FAT_WRITE=y -CONFIG_LZO=y -# CONFIG_OF_LIBFDT_OVERLAY is not set -# CONFIG_EFI_LOADER is not set diff --git a/configs/brppt1_spi_defconfig b/configs/brppt1_spi_defconfig deleted file mode 100644 index fa6b840d9e..0000000000 --- a/configs/brppt1_spi_defconfig +++ /dev/null @@ -1,130 +0,0 @@ -CONFIG_ARM=y -CONFIG_ARCH_OMAP2PLUS=y -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_SYS_MALLOC_F_LEN=0x4000 -CONFIG_SPL_GPIO=y -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=1 -CONFIG_ENV_SIZE=0x10000 -CONFIG_ENV_OFFSET=0x20000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DM_GPIO=y -CONFIG_SPL_DM_SPI=y -CONFIG_DEFAULT_DEVICE_TREE="am335x-brppt1-spi" -CONFIG_AM33XX=y -CONFIG_TARGET_BRPPT1=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL=y -CONFIG_ENV_OFFSET_REDUND=0x30000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI=y -CONFIG_SYS_LOAD_ADDR=0x80000000 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x4030ff00 -# CONFIG_EXPERT is not set -# CONFIG_FIT is not set -CONFIG_OF_BOARD_SETUP=y -CONFIG_SPI_BOOT=y -CONFIG_BOOTDELAY=0 -CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="run b_default" -CONFIG_USE_PREBOOT=y -CONFIG_PREBOOT="run cfgscr; run brdefaultip" -CONFIG_SYS_CONSOLE_IS_IN_ENV=y -CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y -CONFIG_SYS_CONSOLE_INFO_QUIET=y -# CONFIG_DISPLAY_CPUINFO is not set -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_SPL_SYS_MALLOC_SIMPLE=y -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_SPL_MALLOC_SIZE=0x500000 -# CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is not set -CONFIG_SPL_I2C=y -# CONFIG_SPL_NAND_SUPPORT is not set -CONFIG_SPL_DM_SPI_FLASH=y -CONFIG_SPL_POWER=y -CONFIG_SPL_SPI_LOAD=y -CONFIG_SYS_SPI_U_BOOT_OFFS=0x40000 -CONFIG_SPL_WATCHDOG=y -CONFIG_SPL_YMODEM_SUPPORT=y -CONFIG_HUSH_PARSER=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_CBSIZE=512 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_SYS_BOOTM_LEN=0x2000000 -# CONFIG_CMD_IMI is not set -# CONFIG_CMD_XIMG is not set -# CONFIG_CMD_EDITENV is not set -# CONFIG_CMD_CRC32 is not set -# CONFIG_CMD_FLASH is not set -CONFIG_CMD_GPIO=y -CONFIG_CMD_I2C=y -# CONFIG_CMD_LOADS is not set -CONFIG_CMD_MMC=y -CONFIG_CMD_BKOPS_ENABLE=y -CONFIG_CMD_PART=y -CONFIG_CMD_USB=y -# CONFIG_CMD_ITEST is not set -CONFIG_CMD_DHCP=y -CONFIG_BOOTP_MAY_FAIL=y -# CONFIG_CMD_NFS is not set -CONFIG_SYS_DISABLE_AUTOLOAD=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_BOOTCOUNT=y -CONFIG_CMD_CACHE=y -CONFIG_CMD_TIME=y -CONFIG_CMD_EXT4=y -CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y -# CONFIG_SPL_DOS_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_SPL_OF_CONTROL=y -CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupt-controller interrupt-cells dma-names dmas " -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_REDUNDAND_ENVIRONMENT=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_VERSION_VARIABLE=y -CONFIG_NET_RETRY_COUNT=10 -CONFIG_BOOTP_SEND_HOSTNAME=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_NETCONSOLE=y -CONFIG_DM=y -CONFIG_SPL_DM=y -CONFIG_SPL_DM_SEQ_ALIAS=y -# CONFIG_OF_TRANSLATE is not set -CONFIG_BOOTCOUNT_LIMIT=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_MISC=y -CONFIG_MMC_OMAP_HS=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -CONFIG_SF_DEFAULT_SPEED=24000000 -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_WINBOND=y -# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set -CONFIG_PHY_NATSEMI=y -CONFIG_DRIVER_TI_CPSW=y -CONFIG_DM_PMIC=y -# CONFIG_SPL_DM_PMIC is not set -CONFIG_PMIC_TPS65217=y -CONFIG_DM_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_OMAP3_SPI=y -CONFIG_USB=y -CONFIG_USB_MUSB_HOST=y -CONFIG_USB_MUSB_GADGET=y -CONFIG_USB_MUSB_TI=y -CONFIG_USB_STORAGE=y -CONFIG_USB_GADGET=y -CONFIG_FAT_WRITE=y -CONFIG_LZO=y -# CONFIG_OF_LIBFDT_OVERLAY is not set -# CONFIG_EFI_LOADER is not set diff --git a/include/configs/brppt1.h b/include/configs/brppt1.h index 6cb1a10600..481473ae2c 100644 --- a/include/configs/brppt1.h +++ b/include/configs/brppt1.h @@ -27,31 +27,7 @@ * the Linux kernel. */
-#ifdef CONFIG_SPL_OS_BOOT -/* RAW SD card / eMMC */ - -#endif /* CONFIG_SPL_OS_BOOT */ - -#ifdef CONFIG_MTD_RAW_NAND -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#endif /* CONFIG_MTD_RAW_NAND */ - -#ifdef CONFIG_MTD_RAW_NAND -#define NANDTGTS \ -"cfgscr=mw ${dtbaddr} 0; nand read ${cfgaddr} cfgscr && source ${cfgaddr};" \ -" fdt addr ${dtbaddr} || cp ${fdtcontroladdr} ${dtbaddr} 4000\0" \ -"nandargs=setenv bootargs console=${console} ${optargs} ${optargs_rot} " \ - "root=mtd6 rootfstype=jffs2 b_mode=${b_mode}\0" \ -"b_nand=nand read ${loadaddr} kernel; nand read ${dtbaddr} dtb; " \ - "run nandargs; run cfgscr; bootz ${loadaddr} - ${dtbaddr}\0" \ -"b_tgts_std=usb0 nand net\0" \ -"b_tgts_rcy=net usb0 nand\0" \ -"b_tgts_pme=usb0 nand net\0" -#else -#define NANDTGTS "" -#endif /* CONFIG_MTD_RAW_NAND */ - -#define MMCSPI_TGTS \ +#define MMC_TGTS \ "t30args#0=setenv bootargs ${optargs_rot} ${optargs} console=${console} " \ "b_mode=${b_mode} root=/dev/mmcblk0p2 rootfstype=ext4\0" \ "b_t30lgcy#0=" \ @@ -76,7 +52,7 @@
#ifdef CONFIG_ENV_IS_IN_MMC #define MMCTGTS \ -MMCSPI_TGTS \ +MMC_TGTS \ "cfgscr=mw ${dtbaddr} 0;" \ " mmc dev 1; mmc read ${cfgaddr} 200 80; source ${cfgaddr};" \ " fdt addr ${dtbaddr} || cp ${fdtcontroladdr} ${dtbaddr} 4000\0" @@ -84,16 +60,6 @@ MMCSPI_TGTS \ #define MMCTGTS "" #endif /* CONFIG_MMC */
-#ifdef CONFIG_SPI -#define SPITGTS \ -MMCSPI_TGTS \ -"cfgscr=mw ${dtbaddr} 0;" \ -" sf probe; sf read ${cfgaddr} 0xC0000 10000; source ${cfgaddr};" \ -" fdt addr ${dtbaddr} || cp ${fdtcontroladdr} ${dtbaddr} 4000\0" -#else -#define SPITGTS "" -#endif /* CONFIG_SPI */ - #define LOAD_OFFSET(x) 0x8##x
#define CONFIG_EXTRA_ENV_SETTINGS \ @@ -110,8 +76,6 @@ BUR_COMMON_ENV \ "b_usb0=usb start && load usb 0 ${scraddr} bootscr.img && source ${scraddr}\0" \ "b_net=tftp ${scraddr} netscript.img && source ${scraddr}\0" \ MMCTGTS \ -SPITGTS \ -NANDTGTS \ "b_deftgts=if test ${b_mode} = 12; then setenv b_tgts ${b_tgts_pme};" \ " elif test ${b_mode} = 0; then setenv b_tgts ${b_tgts_rcy};" \ " else setenv b_tgts ${b_tgts_std}; fi\0" \ @@ -119,28 +83,4 @@ NANDTGTS \ " do echo "### booting ${target} ###"; run b_${target};" \ " if test ${b_break} = 1; then; exit; fi; done\0"
-#ifdef CONFIG_MTD_RAW_NAND -/* - * GPMC block. We support 1 device and the physical address to - * access CS0 at is 0x8000000. - */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x8000000 -/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */ -#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \ - 10, 11, 12, 13, 14, 15, 16, 17, \ - 18, 19, 20, 21, 22, 23, 24, 25, \ - 26, 27, 28, 29, 30, 31, 32, 33, \ - 34, 35, 36, 37, 38, 39, 40, 41, \ - 42, 43, 44, 45, 46, 47, 48, 49, \ - 50, 51, 52, 53, 54, 55, 56, 57, } - -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 14 - -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE - -#define CONFIG_NAND_OMAP_GPMC_WSCFG 1 -#endif /* CONFIG_MTD_RAW_NAND */ - #endif /* ! __CONFIG_BRPPT1_H__ */