This patch adds basic support for the Marvell Armada 7K DB-88F7040 development board. Supported are the following interfaces: - UART - SPI (incl. SPI NOR) - I2C - USB - SATA / AHCI
Support for other interfaces will follow.
Signed-off-by: Stefan Roese sr@denx.de Cc: Nadav Haklai nadavh@marvell.com Cc: Neta Zur Hershkovits neta@marvell.com Cc: Kostya Porotchkin kostap@marvell.com Cc: Omri Itach omrii@marvell.com Cc: Igal Liberman igall@marvell.com Cc: Haim Boot hayim@marvell.com Cc: Hanna Hawa hannah@marvell.com --- arch/arm/mach-mvebu/Kconfig | 7 ++ board/Marvell/mvebu_db-88f7040/MAINTAINERS | 6 ++ board/Marvell/mvebu_db-88f7040/Makefile | 7 ++ board/Marvell/mvebu_db-88f7040/board.c | 152 +++++++++++++++++++++++++++++ configs/mvebu_db-88f7040_defconfig | 47 +++++++++ include/configs/mvebu_db-88f7040.h | 133 +++++++++++++++++++++++++ 6 files changed, 352 insertions(+) create mode 100644 board/Marvell/mvebu_db-88f7040/MAINTAINERS create mode 100644 board/Marvell/mvebu_db-88f7040/Makefile create mode 100644 board/Marvell/mvebu_db-88f7040/board.c create mode 100644 configs/mvebu_db-88f7040_defconfig create mode 100644 include/configs/mvebu_db-88f7040.h
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 54b3b72..9bdcdc8 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -73,6 +73,10 @@ config TARGET_DB_88F6820_GP bool "Support DB-88F6820-GP" select DB_88F6820_GP
+config TARGET_MVEBU_DB_88F7040 + bool "Support DB-88F7040 Armada 7040" + select ARMADA_8K + config TARGET_DB_MV784MP_GP bool "Support db-mv784mp-gp" select MV78460 @@ -96,6 +100,7 @@ config SYS_BOARD default "mvebu_db-88f3720" if TARGET_MVEBU_DB_88F3720 default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP + default "mvebu_db-88f7040" if TARGET_MVEBU_DB_88F7040 default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP default "ds414" if TARGET_DS414 default "maxbcm" if TARGET_MAXBCM @@ -106,6 +111,7 @@ config SYS_CONFIG_NAME default "mvebu_db-88f3720" if TARGET_MVEBU_DB_88F3720 default "db-88f6720" if TARGET_DB_88F6720 default "db-88f6820-gp" if TARGET_DB_88F6820_GP + default "mvebu_db-88f7040" if TARGET_MVEBU_DB_88F7040 default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP default "ds414" if TARGET_DS414 default "maxbcm" if TARGET_MAXBCM @@ -116,6 +122,7 @@ config SYS_VENDOR default "Marvell" if TARGET_MVEBU_DB_88F3720 default "Marvell" if TARGET_DB_88F6720 default "Marvell" if TARGET_DB_88F6820_GP + default "Marvell" if TARGET_MVEBU_DB_88F7040 default "solidrun" if TARGET_CLEARFOG default "Synology" if TARGET_DS414
diff --git a/board/Marvell/mvebu_db-88f7040/MAINTAINERS b/board/Marvell/mvebu_db-88f7040/MAINTAINERS new file mode 100644 index 0000000..820461b --- /dev/null +++ b/board/Marvell/mvebu_db-88f7040/MAINTAINERS @@ -0,0 +1,6 @@ +MVEBU_DB_88F7040 BOARD +M: Stefan Roese sr@denx.de +S: Maintained +F: board/Marvell/mvebu_db-88f7040/ +F: include/configs/mvebu_db-88f7040.h +F: configs/mvebu_db-88f7040_defconfig diff --git a/board/Marvell/mvebu_db-88f7040/Makefile b/board/Marvell/mvebu_db-88f7040/Makefile new file mode 100644 index 0000000..ed39738 --- /dev/null +++ b/board/Marvell/mvebu_db-88f7040/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2016 Stefan Roese sr@denx.de +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := board.o diff --git a/board/Marvell/mvebu_db-88f7040/board.c b/board/Marvell/mvebu_db-88f7040/board.c new file mode 100644 index 0000000..48bd55c --- /dev/null +++ b/board/Marvell/mvebu_db-88f7040/board.c @@ -0,0 +1,152 @@ +/* + * Copyright (C) 2016 Stefan Roese sr@denx.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* IO expander I2C device */ +#define I2C_IO_EXP_ADDR 0x21 +#define I2C_IO_CFG_REG_0 0x6 +#define I2C_IO_DATA_OUT_REG_0 0x2 +/* VBus enable */ +#define I2C_IO_REG_0_USB_H0_OFF 0 +#define I2C_IO_REG_0_USB_H1_OFF 1 +#define I2C_IO_REG_VBUS ((1 << I2C_IO_REG_0_USB_H0_OFF) | \ + (1 << I2C_IO_REG_0_USB_H1_OFF)) +/* Current limit */ +#define I2C_IO_REG_0_USB_H0_CL 4 +#define I2C_IO_REG_0_USB_H1_CL 5 +#define I2C_IO_REG_CL ((1 << I2C_IO_REG_0_USB_H0_CL) | \ + (1 << I2C_IO_REG_0_USB_H1_CL)) + +static int usb_enabled = 0; + +/* Board specific xHCI dis-/enable code */ + +/* + * Set USB VBUS signals (via I2C IO expander/GPIO) as output and set + * output value as disabled + * + * Set USB Current Limit signals (via I2C IO expander/GPIO) as output + * and set output value as enabled + */ +int board_xhci_config(void) +{ + struct udevice *dev; + int ret; + u8 buf[8]; + + /* Configure IO exander PCA9555: 7bit address 0x21 */ + ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); + if (ret) { + printf("Cannot find PCA9555: %d\n", ret); + return 0; + } + + /* + * Read configuration (direction) and set VBUS pin as output + * (reset pin = output) + */ + ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1); + if (ret) { + printf("Failed to read IO expander value via I2C\n"); + return -EIO; + } + buf[0] &= ~I2C_IO_REG_VBUS; + buf[0] &= ~I2C_IO_REG_CL; + ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + /* Read output value and configure it */ + ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to read IO expander value via I2C\n"); + return -EIO; + } + buf[0] &= ~I2C_IO_REG_VBUS; + buf[0] |= I2C_IO_REG_CL; + ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + mdelay(500); /* required delay to let output value settle */ + + return 0; +} + +int board_xhci_enable(void) +{ + struct udevice *dev; + int ret; + u8 buf[8]; + + /* + * This function enables all USB ports simultaniously, + * it only needs to get called once + */ + if (usb_enabled) + return 0; + + /* Configure IO exander PCA9555: 7bit address 0x21 */ + ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev); + if (ret) { + printf("Cannot find PCA9555: %d\n", ret); + return 0; + } + + /* Read VBUS output value */ + ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to read IO expander value via I2C\n"); + return -EIO; + } + + /* Enable VBUS power: Set output value of VBUS pin as enabled */ + buf[0] |= I2C_IO_REG_VBUS; + ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1); + if (ret) { + printf("Failed to set IO expander via I2C\n"); + return -EIO; + } + + mdelay(500); /* required delay to let output value settle */ + usb_enabled = 1; + + return 0; +} + +int board_early_init_f(void) +{ + /* Nothing to do (yet), perhaps later some pin-muxing etc */ + + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; + + return 0; +} + +int board_late_init(void) +{ + /* Pre-configure the USB ports (overcurrent, VBus) */ + board_xhci_config(); + + return 0; +} diff --git a/configs/mvebu_db-88f7040_defconfig b/configs/mvebu_db-88f7040_defconfig new file mode 100644 index 0000000..4d68bdc --- /dev/null +++ b/configs/mvebu_db-88f7040_defconfig @@ -0,0 +1,47 @@ +CONFIG_ARM=y +CONFIG_ARCH_MVEBU=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_TARGET_MVEBU_DB_88F7040=y +CONFIG_DEFAULT_DEVICE_TREE="armada-7040-db" +CONFIG_AHCI=y +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +CONFIG_CMD_SF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_I2C=y +CONFIG_CMD_USB=y +# CONFIG_CMD_FPGA is not set +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_BLOCK_CACHE=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MVTWSI=y +CONFIG_MISC=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_SPANSION=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_PHYLIB=y +CONFIG_MVEBU_COMPHY_SUPPORT=y +# CONFIG_SPL_SERIAL_PRESENT is not set +CONFIG_DEBUG_UART=y +CONFIG_DEBUG_UART_BASE=0xf0512000 +CONFIG_DEBUG_UART_CLOCK=200000000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_SYS_NS16550=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y diff --git a/include/configs/mvebu_db-88f7040.h b/include/configs/mvebu_db-88f7040.h new file mode 100644 index 0000000..cfb0191 --- /dev/null +++ b/include/configs/mvebu_db-88f7040.h @@ -0,0 +1,133 @@ +/* + * Copyright (C) 2016 Stefan Roese sr@denx.de + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_MVEBU_DB_88F7040_H +#define _CONFIG_MVEBU_DB_88F7040_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +#define CONFIG_DISPLAY_BOARDINFO_LATE +#define CONFIG_ARCH_EARLY_INIT_R +#define CONFIG_BOARD_LATE_INIT + +#define CONFIG_SYS_TEXT_BASE 0x00000000 + +/* additions for new ARM relocation support */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 + +#define CONFIG_NR_DRAM_BANKS 1 + +/* auto boot */ +#define CONFIG_PREBOOT + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \ + 115200, 230400, 460800, 921600 } + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG /* enable INITRD tag */ +#define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */ + +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */ + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* 4MiB for malloc() */ + +/* + * Other required minimal configurations + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */ +#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ +#define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */ +#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ +#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */ +#define CONFIG_SYS_MEMTEST_END 0x00ffffff /*(_16M -1) */ +#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ +#define CONFIG_SYS_ALT_MEMTEST + +/* End of 16M scrubbed by training in bootrom */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE + 0xFF0000) + +/* + * SPI Flash configuration + */ +#define CONFIG_KIRKWOOD_SPI +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE + +/* Environment in SPI NOR flash */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x180000 /* as Marvell U-Boot version */ +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ +#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ + +/* USB 2.0 */ +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 + +/* USB 3.0 */ +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 3 + +#define CONFIG_USB_MAX_CONTROLLER_COUNT (CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS + \ + CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS) + +/* USB ethernet */ +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_MCS7830 +#define CONFIG_USB_ETHER_RTL8152 +#define CONFIG_USB_ETHER_SMSC95XX + +/* + * SATA/SCSI/AHCI configuration + */ +#define CONFIG_SCSI +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_LIBATA +#define CONFIG_LBA48 +#define CONFIG_SYS_64BIT_LBA + +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 2 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +#define CONFIG_SUPPORT_VFAT + +/* DISK Partition support */ +#define CONFIG_EFI_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_MAC_PARTITION +#define CONFIG_ISO_PARTITION /* Experimental */ + +#define CONFIG_CMD_PART +#define CONFIG_PARTITION_UUIDS + +#endif /* _CONFIG_MVEBU_DB_88F7040_H */