Radxa E25 is a network application carrier board for the Radxa CM3I SoM with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key, USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4: - SD-card boot - eMMC boot - USB host - PCIe/Ethernet adapters is detected - SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman jonas@kwiboo.se Reviewed-by: Kever Yang kever.yang@rock-chips.com --- Changes in v3: - Rebased on master and "board: rockchip: Add Pine64 Quartz64 and SOQuartz boards" v2 series - Sync device tree from linux next-20230728 to include sata1, combphy1 and regulator fixes merged into linux maintainer tree since v2 - Drop u-boot.dtsi pcie pinctrl change that caused pinmux issue in linux when using EFI boot flow - Collect r-b tag
Changes in v2: - Remove the unneeded always-on/boot-on prop of vcc3v3_pi6c_05 - Drop PCI_INIT_R=y and add MMC_HS200_SUPPORT=y to speed up boot - Enable sata1 node and set correct regulator to combphy1 node, can be dropped in a future DT sync once linux patch [1] lands
This patch depends on the series "board: rockchip: Add Pine64 Quartz64 and SOQuartz boards" v2 [2] and all its depends.
A copy of this patch and all its depends can be found at [3].
[1] https://lore.kernel.org/linux-rockchip/20230724145213.3833099-1-jonas@kwiboo... [2] https://patchwork.ozlabs.org/project/uboot/list/?series=366399 [3] https://github.com/Kwiboo/u-boot-rockchip/commits/rk3568-radxa-e25-v3
arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3568-radxa-cm3i.dtsi | 415 ++++++++++++++++++++++ arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi | 32 ++ arch/arm/dts/rk3568-radxa-e25.dts | 236 ++++++++++++ board/rockchip/evb_rk3568/MAINTAINERS | 8 + configs/radxa-e25-rk3568_defconfig | 94 +++++ doc/board/rockchip/rockchip.rst | 1 + 7 files changed, 787 insertions(+) create mode 100644 arch/arm/dts/rk3568-radxa-cm3i.dtsi create mode 100644 arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi create mode 100644 arch/arm/dts/rk3568-radxa-e25.dts create mode 100644 configs/radxa-e25-rk3568_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index bf8c568260a6..01aba388994e 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -180,6 +180,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3568-nanopi-r5c.dtb \ rk3568-nanopi-r5s.dtb \ rk3568-odroid-m1.dtb \ + rk3568-radxa-e25.dtb \ rk3568-rock-3a.dtb
dtb-$(CONFIG_ROCKCHIP_RK3588) += \ diff --git a/arch/arm/dts/rk3568-radxa-cm3i.dtsi b/arch/arm/dts/rk3568-radxa-cm3i.dtsi new file mode 100644 index 000000000000..c50fbdd48680 --- /dev/null +++ b/arch/arm/dts/rk3568-radxa-cm3i.dtsi @@ -0,0 +1,415 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include "rk3568.dtsi" + +/ { + compatible = "radxa,cm3i", "rockchip,rk3568"; + + aliases { + mmc0 = &sdhci; + }; + + chosen { + stdout-path = "serial2:115200n8"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_user: led-0 { + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; + function = LED_FUNCTION_HEARTBEAT; + color = <LED_COLOR_ID_GREEN>; + linux,default-trigger = "heartbeat"; + pinctrl-names = "default"; + pinctrl-0 = <&led_user_en>; + }; + }; + + pcie30_avdd0v9: pcie30-avdd0v9-regulator { + compatible = "regulator-fixed"; + regulator-name = "pcie30_avdd0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + vin-supply = <&vcc3v3_sys>; + }; + + pcie30_avdd1v8: pcie30-avdd1v8-regulator { + compatible = "regulator-fixed"; + regulator-name = "pcie30_avdd1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc3v3_sys>; + }; + + vcc3v3_sys: vcc3v3-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v_input>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v_input>; + }; + + /* labeled +5v_input in schematic */ + vcc5v_input: vcc5v-input-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v_input"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +&combphy0 { + status = "okay"; +}; + +&combphy1 { + status = "okay"; +}; + +&combphy2 { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu1 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu2 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu3 { + cpu-supply = <&vdd_cpu>; +}; + +&display_subsystem { + status = "disabled"; +}; + +&gpu { + mali-supply = <&vdd_gpu>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + vdd_cpu: regulator@1c { + compatible = "tcs,tcs4525"; + reg = <0x1c>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc5v_input>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc3v3_sys>; + vcc2-supply = <&vcc3v3_sys>; + vcc3-supply = <&vcc3v3_sys>; + vcc4-supply = <&vcc3v3_sys>; + vcc5-supply = <&vcc3v3_sys>; + vcc6-supply = <&vcc3v3_sys>; + vcc7-supply = <&vcc3v3_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc3v3_sys>; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-name = "vdd_logic"; + regulator-always-on; + regulator-boot-on; + regulator-init-microvolt = <900000>; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-name = "vdd_gpu"; + regulator-always-on; + regulator-init-microvolt = <900000>; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdd_npu: DCDC_REG4 { + regulator-name = "vdd_npu"; + regulator-init-microvolt = <900000>; + regulator-initial-mode = <0x2>; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <6001>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: DCDC_REG5 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_image: LDO_REG1 { + regulator-name = "vdda0v9_image"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v9: LDO_REG2 { + regulator-name = "vdda_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-name = "vdda0v9_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-name = "vccio_acodec"; + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-name = "vccio_sd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-name = "vcc3v3_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcca_1v8: LDO_REG7 { + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pmu: LDO_REG8 { + regulator-name = "vcca1v8_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca1v8_image: LDO_REG9 { + regulator-name = "vcca1v8_image"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_3v3: SWITCH_REG1 { + regulator-name = "vcc_3v3"; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_sd: SWITCH_REG2 { + regulator-name = "vcc3v3_sd"; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&pinctrl { + leds { + led_user_en: led_user_en { + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int: pmic_int { + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; + +&pmu_io_domains { + pmuio1-supply = <&vcc3v3_pmu>; + pmuio2-supply = <&vcc3v3_pmu>; + vccio1-supply = <&vccio_acodec>; + vccio2-supply = <&vcc_1v8>; + vccio3-supply = <&vccio_sd>; + vccio4-supply = <&vcc_1v8>; + vccio5-supply = <&vcc_3v3>; + vccio6-supply = <&vcc_1v8>; + vccio7-supply = <&vcc_3v3>; + status = "okay"; +}; + +&saradc { + vref-supply = <&vcca_1v8>; + status = "okay"; +}; + +&sdhci { + bus-width = <8>; + max-frequency = <200000000>; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vcc_1v8>; + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&usb2phy0 { + status = "okay"; +}; + +&usb2phy1 { + status = "okay"; +}; + +&usb_host0_xhci { + extcon = <&usb2phy0>; +}; diff --git a/arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi b/arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi new file mode 100644 index 000000000000..572bdc5665b1 --- /dev/null +++ b/arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi @@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0+ + +#include "rk356x-u-boot.dtsi" + +/ { + chosen { + stdout-path = &uart2; + }; +}; + +/* PCIe PHY driver in U-Boot does not support bifurcation */ +&pcie3x1 { + status = "disabled"; +}; + +&sdhci { + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; +}; + +&uart2 { + bootph-all; + clock-frequency = <24000000>; + status = "okay"; +}; + +&usb_host0_xhci { + dr_mode = "host"; +}; diff --git a/arch/arm/dts/rk3568-radxa-e25.dts b/arch/arm/dts/rk3568-radxa-e25.dts new file mode 100644 index 000000000000..72ad74c38a2b --- /dev/null +++ b/arch/arm/dts/rk3568-radxa-e25.dts @@ -0,0 +1,236 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/dts-v1/; +#include "rk3568-radxa-cm3i.dtsi" + +/ { + model = "Radxa E25 Carrier Board"; + compatible = "radxa,e25", "radxa,cm3i", "rockchip,rk3568"; + + aliases { + mmc1 = &sdmmc0; + }; + + pwm-leds { + compatible = "pwm-leds-multicolor"; + + multi-led { + color = <LED_COLOR_ID_RGB>; + max-brightness = <255>; + + led-red { + color = <LED_COLOR_ID_RED>; + pwms = <&pwm1 0 1000000 0>; + }; + + led-green { + color = <LED_COLOR_ID_GREEN>; + pwms = <&pwm2 0 1000000 0>; + }; + + led-blue { + color = <LED_COLOR_ID_BLUE>; + pwms = <&pwm12 0 1000000 0>; + }; + }; + }; + + vbus_typec: vbus-typec-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&vbus_typec_en>; + regulator-name = "vbus_typec"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc5v0_sys>; + }; + + /* actually fed by vcc5v0_sys, dependent + * on pi6c clock generator + */ + vcc3v3_minipcie: vcc3v3-minipcie-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&minipcie_enable_h>; + regulator-name = "vcc3v3_minipcie"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc3v3_pi6c_05>; + }; + + vcc3v3_ngff: vcc3v3-ngff-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&ngffpcie_enable_h>; + regulator-name = "vcc3v3_ngff"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc3v3_pcie30x1: vcc3v3-pcie30x1-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie30x1_enable_h>; + regulator-name = "vcc3v3_pcie30x1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc3v3_pi6c_05: vcc3v3-pi6c-05-regulator { + compatible = "regulator-fixed"; + enable-active-high; + gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_enable_h>; + regulator-name = "vcc3v3_pcie"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; +}; + +&combphy1 { + phy-supply = <&vcc3v3_pcie30x1>; +}; + +&pcie2x1 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie20_reset_h>; + reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_pi6c_05>; + status = "okay"; +}; + +&pcie30phy { + data-lanes = <1 2>; + status = "okay"; +}; + +&pcie3x1 { + num-lanes = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie30x1m0_pins>; + reset-gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_minipcie>; + status = "okay"; +}; + +&pcie3x2 { + num-lanes = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie30x2_reset_h>; + reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_pi6c_05>; + status = "okay"; +}; + +&pinctrl { + pcie { + pcie20_reset_h: pcie20-reset-h { + rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie30x1_enable_h: pcie30x1-enable-h { + rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie30x2_reset_h: pcie30x2-reset-h { + rockchip,pins = <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + pcie_enable_h: pcie-enable-h { + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb { + minipcie_enable_h: minipcie-enable-h { + rockchip,pins = <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + ngffpcie_enable_h: ngffpcie-enable-h { + rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vbus_typec_en: vbus_typec_en { + rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&pwm1 { + status = "okay"; +}; + +&pwm2 { + status = "okay"; +}; + +&pwm12 { + pinctrl-names = "default"; + pinctrl-0 = <&pwm12m1_pins>; + status = "okay"; +}; + +&sata1 { + status = "okay"; +}; + +&sdmmc0 { + bus-width = <4>; + cap-sd-highspeed; + cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; + /* Also used in pcie30x1_clkreqnm0 */ + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd>; + sd-uhs-sdr104; + vmmc-supply = <&vcc3v3_sd>; + vqmmc-supply = <&vccio_sd>; + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; + +&usb_host0_xhci { + status = "okay"; +}; + +&usb_host1_ehci { + status = "okay"; +}; + +&usb_host1_ohci { + status = "okay"; +}; + +&usb2phy0_otg { + phy-supply = <&vbus_typec>; + status = "okay"; +}; + +&usb2phy1_host { + phy-supply = <&vcc3v3_minipcie>; + status = "okay"; +}; + +&usb2phy1_otg { + phy-supply = <&vcc3v3_ngff>; + status = "okay"; +}; diff --git a/board/rockchip/evb_rk3568/MAINTAINERS b/board/rockchip/evb_rk3568/MAINTAINERS index a8ed2508a162..82a92b89fa64 100644 --- a/board/rockchip/evb_rk3568/MAINTAINERS +++ b/board/rockchip/evb_rk3568/MAINTAINERS @@ -27,6 +27,14 @@ M: Jagan Teki jagan@amarulasolutions.com S: Maintained F: configs/radxa-cm3-io-rk3566_defconfig
+RADXA-E25 +M: Jonas Karlman jonas@kwiboo.se +S: Maintained +F: configs/radxa-e25-rk3568_defconfig +F: arch/arm/dts/rk3568-radxa-cm3i.dtsi +F: arch/arm/dts/rk3568-radxa-e25.dts +F: arch/arm/dts/rk3568-radxa-e25-u-boot.dtsi + ROCK-3A M: Akash Gajjar gajjar04akash@gmail.com S: Maintained diff --git a/configs/radxa-e25-rk3568_defconfig b/configs/radxa-e25-rk3568_defconfig new file mode 100644 index 000000000000..a905100a794d --- /dev/null +++ b/configs/radxa-e25-rk3568_defconfig @@ -0,0 +1,94 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_SYS_HAS_NONCACHED_MEMORY=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_DEFAULT_DEVICE_TREE="rk3568-radxa-e25" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_PCI=y +CONFIG_DEBUG_UART=y +CONFIG_AHCI=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-radxa-e25.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_AHCI_PCI=y +CONFIG_DWC_AHCI=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_HS200_SUPPORT=y +CONFIG_SPL_MMC_HS200_SUPPORT=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +CONFIG_RTL8169=y +CONFIG_PCIE_DW_ROCKCHIP=y +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_SCSI=y +CONFIG_DM_SCSI=y +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_ERRNO_STR=y diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst index e23237e453f3..10fffb56f13d 100644 --- a/doc/board/rockchip/rockchip.rst +++ b/doc/board/rockchip/rockchip.rst @@ -101,6 +101,7 @@ List of mainline supported Rockchip boards: - Pine64 SOQuartz on Blade (soquartz-blade-rk3566_defconfig) - Pine64 SOQuartz on CM4-IO (soquartz-cm4-rk3566_defconfig) - Pine64 SOQuartz on Model A (soquartz-model-a-rk3566_defconfig) + - Radxa E25 Carrier Board (radxa-e25-rk3568_defconfig)
* rk3588 - Rockchip EVB (evb-rk3588)