Hi,
On 12/2/22 22:03, Sean Anderson wrote:
This adds the UUU UCmd functionality as an OEM command. While the fastboot tool allows sending arbitrary commands as long as they are prefixed with "oem". This allows running generic U-Boot commands over fastboot without UUU, which is especially useful when not using USB. This is really the route we should have gone in the first place when adding these commands.
While we're here, clean up the Kconfig a bit.
Signed-off-by: Sean Anderson sean.anderson@seco.com
Changes in v2:
Document usage
Keep enum in order
doc/android/fastboot.rst | 15 +++++++++++++++ drivers/fastboot/Kconfig | 10 +++++----- drivers/fastboot/fb_command.c | 4 ++++ include/fastboot.h | 1 + 4 files changed, 25 insertions(+), 5 deletions(-)
diff --git a/doc/android/fastboot.rst b/doc/android/fastboot.rst index 7611f07038..7f343d5dfc 100644 --- a/doc/android/fastboot.rst +++ b/doc/android/fastboot.rst @@ -28,6 +28,7 @@ The following OEM commands are supported (if enabled):
- ``oem partconf`` - this executes ``mmc partconf %x <arg> 0`` to configure eMMC with <arg> = boot_ack boot_partition
- ``oem bootbus`` - this executes ``mmc bootbus %x %s`` to configure eMMC
+- ``oem run`` - this executes an arbitrary U-Boot command
Support for both eMMC and NAND devices is included.
@@ -127,6 +128,19 @@ Boot command When executing the fastboot ``boot`` command, if ``fastboot_bootcmd`` is set then that will be executed in place of ``bootm <CONFIG_FASTBOOT_BUF_ADDR>``.
+Running Shell Commands +----------------------
+Normally, arbitrary U-Boot command execution is not enabled. This is so +fastboot can be used to update systems using verified boot. However, such +functionality can be useful for production or when verified boot is not in use. +Enable ``CONFIG_FASTBOOT_UUU_SUPPORT`` to use this functionality. This will +enable the ``UCmd`` and ``ACmd`` commands for use with UUU [3]_. It also +enables the ``oem run`` command, which can be used with the fastboot client. +For example, to print "Hello world", run::
- $ fastboot oem run:echo Hello world
Partition Names
@@ -232,3 +246,4 @@ References
.. [1] :doc:`fastboot-protocol` .. [2] https://developer.android.com/studio/releases/platform-tools +.. [3] https://github.com/NXPmicro/mfgtools diff --git a/drivers/fastboot/Kconfig b/drivers/fastboot/Kconfig index b97c67bf60..8f2d52cb8a 100644 --- a/drivers/fastboot/Kconfig +++ b/drivers/fastboot/Kconfig @@ -80,12 +80,12 @@ config FASTBOOT_FLASH this to enable the "fastboot flash" command.
config FASTBOOT_UUU_SUPPORT
- bool "Enable FASTBOOT i.MX UUU special command"
- bool "Enable running arbitrary commands from FASTBOOT" help
The fastboot protocol includes "UCmd" and "ACmd" command.Be aware that you provide full access to any U-Boot command,including working with memory and may open a huge backdoor,when enabling this option.
This extends the fastboot protocol with the "UCmd" and "ACmd"commands, as well as the "oem run" command. These commands providefull access to any U-Boot command, including working with memory.This may open a huge backdoor if you are using verified boot.
why the support of "oem run" generic support is include in the IMX config CONFIG_FASTBOOT_UUU_SUPPORT
"UCmd" and "Acmd" are imx additions in fastboot standard for UUU support
https://android.googlesource.com/platform/system/core/+/2ec418a4c98f6e8f9539...
but "oem run" can be see as generic U-Boot 'oem' command to execute U-boot command.
for me I see 2 separate configs to handle other platform than IMX ones (with UUU support)
config FASTBOOT_CMD_OEM_RUN bool "Enable fastboot oem run command"
config FASTBOOT_UUU_SUPPORT bool "Enable FASTBOOT i.MX UUU special command" select FASTBOOT_CMD_OEM_RUN
PS: FASTBOOT_UUU_SUPPORT could depends on CONFIG_ARCH_IMX*
choice prompt "Flash provider for FASTBOOT" diff --git a/drivers/fastboot/fb_command.c b/drivers/fastboot/fb_command.c index 98eccc3455..1732406c18 100644 --- a/drivers/fastboot/fb_command.c +++ b/drivers/fastboot/fb_command.c @@ -123,6 +123,10 @@ static const struct { }, #endif #if CONFIG_IS_ENABLED(FASTBOOT_UUU_SUPPORT)
- [FASTBOOT_COMMAND_OEM_RUN] = {
.command = "oem run",.dispatch = run_ucmd,- },
#if CONFIG_IS_ENABLED(FASTBOOT_CMD_OEM_RUN) [FASTBOOT_COMMAND_OEM_RUN] = { .command = "oem run", .dispatch = run_ucmd, },
#endif
#if CONFIG_IS_ENABLED(FASTBOOT_UUU_SUPPORT)
[FASTBOOT_COMMAND_UCMD] = { .command = "UCmd", .dispatch = run_ucmd,
That allows other platform to enable FASTBOOT_CMD_OEM_RUN but not FASTBOOT_UUU_SUPPORT.
[FASTBOOT_COMMAND_UCMD] = { .command = "UCmd", .dispatch = run_ucmd, diff --git a/include/fastboot.h b/include/fastboot.h index 57daaf1298..8b6b4b934a 100644 --- a/include/fastboot.h +++ b/include/fastboot.h @@ -45,6 +45,7 @@ enum { FASTBOOT_COMMAND_OEM_BOOTBUS, #endif #if CONFIG_IS_ENABLED(FASTBOOT_UUU_SUPPORT)
- FASTBOOT_COMMAND_OEM_RUN, FASTBOOT_COMMAND_ACMD, FASTBOOT_COMMAND_UCMD, #endif
+#if CONFIG_IS_ENABLED(FASTBOOT_CMD_OEM_RUN)
+ FASTBOOT_COMMAND_OEM_RUN, +#endif
and also some stuff to compile the fucntion run_ucmd()
PS: we have many #if CONFIG is the fastboot source code
they can be replaced by CONFIG_IS_ENABLED macro and __maybe_unused in .h and .c ?
and that avoids the compilation issue => let the linker remove the used functions
for example
enum {
FASTBOOT_COMMAND_GETVAR = 0, FASTBOOT_COMMAND_DOWNLOAD, CONFIG_IS_ENABLED(FASTBOOT_FLASH, (FASTBOOT_COMMAND_FLASH,)) CONFIG_IS_ENABLED(FASTBOOT_FLASH, (FASTBOOT_COMMAND_ERASE,)) FASTBOOT_COMMAND_BOOT, FASTBOOT_COMMAND_CONTINUE, FASTBOOT_COMMAND_REBOOT, FASTBOOT_COMMAND_REBOOT_BOOTLOADER, FASTBOOT_COMMAND_REBOOT_FASTBOOTD, FASTBOOT_COMMAND_REBOOT_RECOVERY, FASTBOOT_COMMAND_SET_ACTIVE, CONFIG_IS_ENABLED(FASTBOOT_CMD_OEM_FORMAT, (FASTBOOT_COMMAND_OEM_FORMAT,)) CONFIG_IS_ENABLED(FASTBOOT_CMD_OEM_PARTCONF, (FASTBOOT_COMMAND_OEM_PARTCONF,)) CONFIG_IS_ENABLED(FASTBOOT_CMD_OEM_BOOTBUS, (FASTBOOT_COMMAND_OEM_BOOTBUS,)) CONFIG_IS_ENABLED(FASTBOOT_UUU_SUPPORT, (FASTBOOT_COMMAND_ACMD,)) CONFIG_IS_ENABLED(FASTBOOT_UUU_SUPPORT, (FASTBOOT_COMMAND_UCMD,)) FASTBOOT_COMMAND_COUNT };
...
ommands[FASTBOOT_COMMAND_COUNT] = { [FASTBOOT_COMMAND_GETVAR] = { .command = "getvar", .dispatch = getvar }, [FASTBOOT_COMMAND_DOWNLOAD] = { .command = "download", .dispatch = download }, CONFIG_IS_ENABLED(FASTBOOT_FLASH, ( [FASTBOOT_COMMAND_FLASH] = { .command = "flash", .dispatch = flash }, [FASTBOOT_COMMAND_ERASE] = { .command = "erase", .dispatch = erase }, )) .... staticvoid__maybe_unused erase(char*cmd_parameter, char*response) { if(CONFIG_IS_ENABLED(FASTBOOT_FLASH_MMC)) fastboot_mmc_erase(cmd_parameter, response); if(CONFIG_IS_ENABLED(FASTBOOT_FLASH_NAND)) fastboot_nand_erase(cmd_parameter, response); }
regards
Patrick