Hello Tom,
-----Original Message----- From: U-Boot u-boot-bounces@lists.denx.de On Behalf Of Andrey Zhizhikin Sent: Friday, December 3, 2021 5:18 PM To: u-boot@lists.denx.de Cc: sbabic@denx.de; festevam@gmail.com; uboot-imx@nxp.com; peng.fan@nxp.com; hs@denx.de; t.remmet@phytec.de; jagan@amarulasolutions.com; marcel.ziswiler@toradex.com; iliev@ronetix.at; xypron.glpk@gmx.de; Andrey Zhizhikin andrey.zhizhikin@leica-geosystems.com Subject: [PATCH v2] imx8mq_evk: switch board to use binman for images
Currently i.MX8MQ EVK board still targeting the old image generation approach for image generation, which relies on the FIT generator that has been dropped from the tree.
Switch the board to use binman instead, which is a standard image generator now.
Update board documentation to correct build command, and advise latest firmware and TF-A versions to use.
NOTE: New image produced by binman does not have Signed HDMI FW support, this has been left on the side and does not interfere with the general boot flow.
Tested on: [i.MX8MQ rev2.0]
Signed-off-by: Andrey Zhizhikin andrey.zhizhikin@leica-geosystems.com
Changes in V2:
- Modify binman and documentation to use single flash.bin file instead of flash.bin+u-boot.itb combination, suggested by Fabio Estevam.
Since you've applied similar patch from Peng, this one is not needed anymore and can be dropped.
There are however few pieces that are present in this patch not picked up in any other patch like doc update, single flash.bin, etc.
I saw that Patrick Wildt had "single flash.bin" part submitted in [1], which would also be beneficial to have in 2022.01 for consistency, and would allow me to update imx8mq_evk machine in meta-freescale Yocto layer so it can be finally built with upstream BSP and 2022.01. If you can pick it up saw well - that would be ideal!
The rest I will extract and send as separate patches after 2022.01.
arch/arm/dts/imx8mq-evk-u-boot.dtsi | 124 ++++++++++++++++++ arch/arm/mach-imx/imx8m/Kconfig | 1 + board/freescale/imx8mq_evk/Kconfig | 2 +- .../imx8mq_evk/imximage-8mq-lpddr4.cfg | 9 ++ configs/imx8mq_evk_defconfig | 2 +- doc/board/nxp/imx8mq_evk.rst | 21 +-- 6 files changed, 148 insertions(+), 11 deletions(-) create mode 100644 board/freescale/imx8mq_evk/imximage-8mq-lpddr4.cfg
diff --git a/arch/arm/dts/imx8mq-evk-u-boot.dtsi b/arch/arm/dts/imx8mq-evk-u- boot.dtsi index 2cfc12b7e0..e3f780ca75 100644 --- a/arch/arm/dts/imx8mq-evk-u-boot.dtsi +++ b/arch/arm/dts/imx8mq-evk-u-boot.dtsi @@ -1,5 +1,129 @@ // SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/ {
- binman: binman {
multiple-images;- };
+};
+&binman {
- u-boot-spl-ddr {
filename = "u-boot-spl-ddr.bin";pad-byte = <0xff>;align-size = <4>;align = <4>;u-boot-spl {align-end = <4>;};blob_1: blob-ext@1 {filename = "lpddr4_pmu_train_1d_imem.bin";size = <0x8000>;};blob_2: blob-ext@2 {filename = "lpddr4_pmu_train_1d_dmem.bin";size = <0x4000>;};blob_3: blob-ext@3 {filename = "lpddr4_pmu_train_2d_imem.bin";size = <0x8000>;};blob_4: blob-ext@4 {filename = "lpddr4_pmu_train_2d_dmem.bin";size = <0x4000>;};- };
- spl {
filename = "spl.bin";mkimage {args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000";blob {filename = "u-boot-spl-ddr.bin";};};- };
- itb {
filename = "u-boot.itb";fit {description = "Configuration to load ATF before U-Boot";#address-cells = <1>;fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>;images {uboot {description = "U-Boot (64-bit)";type = "standalone";arch = "arm64";compression = "none";load = <CONFIG_SYS_TEXT_BASE>;uboot_blob: blob-ext {filename = "u-boot-nodtb.bin";};};atf {description = "ARM Trusted Firmware";type = "firmware";arch = "arm64";compression = "none";load = <0x910000>;entry = <0x910000>;atf_blob: blob-ext {filename = "bl31.bin";};};fdt {description = "NAME";type = "flat_dt";compression = "none";uboot_fdt_blob: blob-ext {filename = "u-boot.dtb";};};};configurations {default = "conf";conf {description = "NAME";firmware = "uboot";loadables = "atf";fdt = "fdt";};};};- };
- imx-boot {
filename = "flash.bin";pad-byte = <0x00>;spl: blob-ext@1 {offset = <0x0>;filename = "spl.bin";};uboot: blob-ext@2 {offset = <0x57c00>;filename = "u-boot.itb";};- };
+};
&usdhc1 { mmc-hs400-1_8v; }; diff --git a/arch/arm/mach-imx/imx8m/Kconfig b/arch/arm/mach-imx/imx8m/Kconfig index 276b8bd974..c556e712b7 100644 --- a/arch/arm/mach-imx/imx8m/Kconfig +++ b/arch/arm/mach-imx/imx8m/Kconfig @@ -36,6 +36,7 @@ config TARGET_IMX8MQ_CM
config TARGET_IMX8MQ_EVK bool "imx8mq_evk"
- select BINMAN select IMX8MQ select IMX8M_LPDDR4
diff --git a/board/freescale/imx8mq_evk/Kconfig b/board/freescale/imx8mq_evk/Kconfig index c4d20ad7c7..08f937f74f 100644 --- a/board/freescale/imx8mq_evk/Kconfig +++ b/board/freescale/imx8mq_evk/Kconfig @@ -10,6 +10,6 @@ config SYS_CONFIG_NAME default "imx8mq_evk"
config IMX_CONFIG
- default "arch/arm/mach-imx/imx8m/imximage.cfg"
- default "board/freescale/imx8mq_evk/imximage-8mq-lpddr4.cfg"
endif diff --git a/board/freescale/imx8mq_evk/imximage-8mq-lpddr4.cfg b/board/freescale/imx8mq_evk/imximage-8mq-lpddr4.cfg new file mode 100644 index 0000000000..90573be5fd --- /dev/null +++ b/board/freescale/imx8mq_evk/imximage-8mq-lpddr4.cfg @@ -0,0 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/*
- Copyright 2021 NXP
- */
+#define __ASSEMBLY__
+BOOT_FROM sd +LOADER u-boot-spl-ddr.bin 0x7E1000 diff --git a/configs/imx8mq_evk_defconfig b/configs/imx8mq_evk_defconfig index 92aae70d4a..f82ce63281 100644 --- a/configs/imx8mq_evk_defconfig +++ b/configs/imx8mq_evk_defconfig @@ -24,7 +24,7 @@ CONFIG_SYS_LOAD_ADDR=0x40480000 CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000 CONFIG_SPL_LOAD_FIT=y -CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh" +# CONFIG_USE_SPL_FIT_GENERATOR is not set CONFIG_BOARD_EARLY_INIT_F=y CONFIG_BOARD_LATE_INIT=y CONFIG_SPL_BOARD_INIT=y diff --git a/doc/board/nxp/imx8mq_evk.rst b/doc/board/nxp/imx8mq_evk.rst index c269fdebe3..436e82151f 100644 --- a/doc/board/nxp/imx8mq_evk.rst +++ b/doc/board/nxp/imx8mq_evk.rst @@ -9,7 +9,7 @@ Quick Start
- Build the ARM Trusted firmware binary
-- Get ddr and hdmi fimware +- Obtain DDR firmware from NXP website
- Build U-Boot
- Boot
@@ -18,7 +18,8 @@ Get and Build the ARM Trusted firmware
Note: srctree is U-Boot source directory Get ATF from: https://source.codeaurora.org/external/imx/imx-atf -branch: imx_5.4.47_2.2.0 +branch: lf_v2.4 +Tag: lf-5.10.52-2.1.0
.. code-block:: bash
@@ -30,11 +31,10 @@ Get the ddr and hdmi firmware
.. code-block:: bash
- $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.9.bin
- $ chmod +x firmware-imx-8.9.bin
- $ ./firmware-imx-8.9.bin
- $ cp firmware-imx-8.9/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(builddir)
- $ cp firmware-imx-8.9/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
- $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.13.bin
- $ chmod +x firmware-imx-8.13.bin
- $ ./firmware-imx-8.13.bin
- $ cp firmware-imx-8.13/firmware/ddr/synopsys/lpddr4*.bin $(builddir)
Build U-Boot
@@ -43,7 +43,8 @@ Build U-Boot
$ export CROSS_COMPILE=aarch64-poky-linux- $ make imx8mq_evk_defconfig
- $ make flash.bin
- $ export ATF_LOAD_ADDR=0x910000
- $ make
Burn the flash.bin to MicroSD card offset 33KB:
@@ -53,4 +54,6 @@ Burn the flash.bin to MicroSD card offset 33KB:
Boot
-Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD. +Set Boot switches to boot from Micro SD: +SW801: 1100 +SW802: 10
base-commit: 5b9ee01685290653671072d0030cd7ba9da3a705
2.25.1
-- andrey
Link: [1]: https://lore.kernel.org/u-boot/Ydmu+cqnqmTHoT0B@ryzen.fritz.box/