This reverts commit 03bb6a9b1ed7085794c5f167307273d15c99d3f0. --- arch/arm/dts/armada-3720-espressobin.dts | 164 ++++++++++++++++++++- arch/arm/dts/armada-3720-espressobin.dtsi | 167 ---------------------- 2 files changed, 157 insertions(+), 174 deletions(-) delete mode 100644 arch/arm/dts/armada-3720-espressobin.dtsi
diff --git a/arch/arm/dts/armada-3720-espressobin.dts b/arch/arm/dts/armada-3720-espressobin.dts index 1542d836c0..be67a45870 100644 --- a/arch/arm/dts/armada-3720-espressobin.dts +++ b/arch/arm/dts/armada-3720-espressobin.dts @@ -1,20 +1,170 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) /* - * Device Tree file for Globalscale Marvell ESPRESSOBin Board + * Device Tree file for Marvell Armada 3720 community board + * (ESPRESSOBin) * Copyright (C) 2016 Marvell * - * Romain Perier romain.perier@free-electrons.com + * Gregory CLEMENT gregory.clement@free-electrons.com + * Konstantin Porotchkin kostap@marvell.com * - */ -/* - * Schematic available at http://espressobin.net/wp-content/uploads/2017/08/ESPRESSObin_V5_Schematics.... + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. */
/dts-v1/;
-#include "armada-3720-espressobin.dtsi" +#include "armada-372x.dtsi"
/ { model = "Globalscale Marvell ESPRESSOBin Board"; compatible = "globalscale,espressobin", "marvell,armada3720", "marvell,armada3710"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + aliases { + ethernet0 = ð0; + i2c0 = &i2c0; + spi0 = &spi0; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x20000000>; + }; + + vcc_sd_reg0: regulator@0 { + compatible = "regulator-gpio"; + regulator-name = "vcc_sd0"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-type = "voltage"; + states = <1800000 0x1 + 3300000 0x0>; + gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; + }; +}; + +&comphy { + max-lanes = <3>; + phy0 { + phy-type = <PHY_TYPE_USB3_HOST0>; + phy-speed = <PHY_SPEED_5G>; + }; + + phy1 { + phy-type = <PHY_TYPE_PEX0>; + phy-speed = <PHY_SPEED_2_5G>; + }; + + phy2 { + phy-type = <PHY_TYPE_SATA0>; + phy-speed = <PHY_SPEED_5G>; + }; +}; + +ð0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>, <&smi_pins>; + phy-mode = "rgmii"; + phy_addr = <0x1>; + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "okay"; +}; + +/* CON3 */ +&sata { + status = "okay"; +}; + +&sdhci0 { + pinctrl-names = "default"; + pinctrl-0 = <&sdio_pins>; + bus-width = <4>; + cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vcc_sd_reg0>; + status = "okay"; +}; + +&spi0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi_quad_pins>; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p128", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <50000000>; + m25p,fast-read; + }; +}; + +/* Exported on the micro USB connector CON32 through an FTDI */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +/* CON29 */ +&usb2 { + status = "okay"; +}; + +/* CON31 */ +&usb3 { + status = "okay"; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pins>; + reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>; + status = "okay"; }; diff --git a/arch/arm/dts/armada-3720-espressobin.dtsi b/arch/arm/dts/armada-3720-espressobin.dtsi deleted file mode 100644 index 05dec89834..0000000000 --- a/arch/arm/dts/armada-3720-espressobin.dtsi +++ /dev/null @@ -1,167 +0,0 @@ -/* - * Device Tree file for Marvell Armada 3720 community board - * (ESPRESSOBin) - * Copyright (C) 2016 Marvell - * - * Gregory CLEMENT gregory.clement@free-electrons.com - * Konstantin Porotchkin kostap@marvell.com - * - * This file is dual-licensed: you can use it either under the terms - * of the GPL or the X11 license, at your option. Note that this dual - * licensing only applies to this file, and not this project as a - * whole. - * - * a) This file is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This file is distributed in the hope that it will be useful - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * Or, alternatively - * - * b) Permission is hereby granted, free of charge, to any person - * obtaining a copy of this software and associated documentation - * files (the "Software"), to deal in the Software without - * restriction, including without limitation the rights to use - * copy, modify, merge, publish, distribute, sublicense, and/or - * sell copies of the Software, and to permit persons to whom the - * Software is furnished to do so, subject to the following - * conditions: - * - * The above copyright notice and this permission notice shall be - * included in all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND - * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES - * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND - * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT - * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY - * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING - * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR - * OTHER DEALINGS IN THE SOFTWARE. - */ - -/dts-v1/; - -#include "armada-372x.dtsi" - -/ { - chosen { - stdout-path = "serial0:115200n8"; - }; - - aliases { - ethernet0 = ð0; - i2c0 = &i2c0; - spi0 = &spi0; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x00000000 0x00000000 0x20000000>; - }; - - vcc_sd_reg0: regulator@0 { - compatible = "regulator-gpio"; - regulator-name = "vcc_sd0"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-type = "voltage"; - states = <1800000 0x1 - 3300000 0x0>; - gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; - }; -}; - -&comphy { - max-lanes = <3>; - phy0 { - phy-type = <PHY_TYPE_USB3_HOST0>; - phy-speed = <PHY_SPEED_5G>; - }; - - phy1 { - phy-type = <PHY_TYPE_PEX0>; - phy-speed = <PHY_SPEED_2_5G>; - }; - - phy2 { - phy-type = <PHY_TYPE_SATA0>; - phy-speed = <PHY_SPEED_5G>; - }; -}; - -ð0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&rgmii_pins>, <&smi_pins>; - phy-mode = "rgmii"; - phy_addr = <0x1>; - fixed-link { - speed = <1000>; - full-duplex; - }; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; - status = "okay"; -}; - -/* CON3 */ -&sata { - status = "okay"; -}; - -&sdhci0 { - pinctrl-names = "default"; - pinctrl-0 = <&sdio_pins>; - bus-width = <4>; - cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; - vqmmc-supply = <&vcc_sd_reg0>; - status = "okay"; -}; - -&spi0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&spi_quad_pins>; - - spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "st,m25p128", "jedec,spi-nor"; - reg = <0>; /* Chip select 0 */ - spi-max-frequency = <50000000>; - m25p,fast-read; - }; -}; - -/* Exported on the micro USB connector CON32 through an FTDI */ -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart1_pins>; - status = "okay"; -}; - -/* CON29 */ -&usb2 { - status = "okay"; -}; - -/* CON31 */ -&usb3 { - status = "okay"; -}; - -&pcie0 { - pinctrl-names = "default"; - pinctrl-0 = <&pcie_pins>; - reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>; - status = "okay"; -};