On Tue, Jul 22, 2014 at 04:03:20PM +0530, pekon gupta wrote:
Beaglebone Board can be connected to expansion boards to add devices to them. These expansion boards are called 'capes'. This patch adds support for following versions of Beaglebone(AM335x) NAND capes (a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64 (b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224 Further information and datasheets can be found at [1] and [2]
- How to boot from NAND using Memory Expander + NAND Cape ? *
Important: As BOOTSEL values are sampled only at POR, so after changing any setting on SW2 (DIP switch), disconnect and reconnect all board power supply (including mini-USB console port) to POR the beaglebone.
Selection of ECC scheme
for NAND cape(a), ROM code expects BCH8_HW ecc-scheme for NAND cape(b), ROM code expects BCH16_HW ecc-scheme
Selction of boot modes can be controlled via DIP switch(SW2) present on Memory Expander cape. SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2) So to flash NAND, first boot via MMC or other sources and then switch to SW2[SWITCH_BOOT]=ON to boot from NAND Cape.
For NAND boot following switch settings need to be followed SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected ) SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- ) SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- ) SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- ) SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- ) SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device ) SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM ) SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device ) SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- )
[1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion [2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Modul...
*IMPORTANT NOTE* As Beaglebone board shares the same config as AM335x EVM, so following changes are required in addition to this patch for Beaglebone NAND cape. (1) Enable NAND in am335x_beaglebone board profile (2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because:
- AM335x EVM has NAND device with datawidth=8, whereas
- Beaglebone NAND cape has NAND device with data-width=16
diff --git a/boards.cfg b/boards.cfg -Active arm armv7 am33xx ti am335x am335x_boneblack am335x_evm:SERIAL1,CONS_INDEX=1,EMMC_BOOT Tom Rini trini@ti.com +Active arm armv7 am33xx ti am335x am335x_boneblack am335x_evm:SERIAL1,CONS_INDEX=1,NAND Tom Rini trini@ti.com
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h +#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
Signed-off-by: Pekon Gupta pekon@ti.com
Applied to u-boot-ti/master, thanks!