LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification: - Rockchip rk3568 - LPDDR4/4X 1/2/4/8 GB - TF scard slot - eMMC 8/32/64/128 GB - Gigabit ethernet x 2 - HDMI out - USB 2.0 Host x 1 - USB 2.0 Type-C OTG x 1 - USB 3.0 Host x 1 - Mini PCIE interface for WIFI/BT module - M.2 key for 2280 NVME - 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan andyshrk@163.com
---
Changes in v4: - Add entry for this board to evb_rk3568/MAINTAINERS - document this board at doc/board/rockchip/rockchip.rst - restore the copyright header of dts from linux kernel - remove ETH_DESIGNWARE from defconfig - remove mmc-hs200-1_8v from u-boot.dsti
Changes in v3: - some alphabetical order update - disable all SPI flash related options. - remove bootph-all for pinctrl - add emmc_datastrobe pinconfig for hs200/hs400 in u-boot.dtsi - use USB_DWC3_GENERIC driver as Jonas suggested. - add CONFIG_SPL_DM_SEQ_ALIAS
Changes in v2: - enable SPL_FIT_SIGNATURE
arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi | 27 + arch/arm/dts/rk3568-lubancat-2.dts | 733 +++++++++++++++++++++ board/rockchip/evb_rk3568/MAINTAINERS | 7 + configs/lubancat-2-rk3568_defconfig | 85 +++ doc/board/rockchip/rockchip.rst | 1 + 6 files changed, 854 insertions(+) create mode 100644 arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3568-lubancat-2.dts create mode 100644 configs/lubancat-2-rk3568_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index bd518064f3..64c885dcf9 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -178,6 +178,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \ rk3566-soquartz-cm4.dtb \ rk3566-soquartz-model-a.dtb \ rk3568-evb.dtb \ + rk3568-lubancat-2.dtb \ rk3568-nanopi-r5c.dtb \ rk3568-nanopi-r5s.dtb \ rk3568-odroid-m1.dtb \ diff --git a/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi new file mode 100644 index 0000000000..27c6277523 --- /dev/null +++ b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2023 Rockchip Electronics Co., Ltd + * (C) Copyright 2023 Andy Yan andyshrk@163.com + */ + +#include "rk356x-u-boot.dtsi" + +/ { + chosen { + stdout-path = &uart2; + }; +}; + +&sdhci { + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; + pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>; +}; + +&uart2 { + bootph-all; + clock-frequency = <24000000>; + status = "okay"; +}; diff --git a/arch/arm/dts/rk3568-lubancat-2.dts b/arch/arm/dts/rk3568-lubancat-2.dts new file mode 100644 index 0000000000..e653b067aa --- /dev/null +++ b/arch/arm/dts/rk3568-lubancat-2.dts @@ -0,0 +1,733 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +/* + * Copyright (c) 2021 Rockchip Electronics Co., Ltd. + * Copyright (c) 2022 EmbedFire embedfire@embedfire.com + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/soc/rockchip,vop2.h> +#include "rk3568.dtsi" + +/ { + model = "EmbedFire LubanCat 2"; + compatible = "embedfire,lubancat-2", "rockchip,rk3568"; + + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + mmc0 = &sdmmc0; + mmc1 = &sdhci; + }; + + chosen: chosen { + stdout-path = "serial2:1500000n8"; + }; + + leds { + compatible = "gpio-leds"; + + user_led: user-led { + label = "user_led"; + linux,default-trigger = "heartbeat"; + default-state = "on"; + gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&user_led_pin>; + }; + }; + + hdmi-con { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + dc_5v: dc-5v-regulator { + compatible = "regulator-fixed"; + regulator-name = "dc_5v"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc3v3_sys: vcc3v3-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc3v3_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc5v0_sys: vcc5v0-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&dc_5v>; + }; + + vcc3v3_m2_pcie: vcc3v3-m2-pcie-regulator { + compatible = "regulator-fixed"; + regulator-name = "m2_pcie_3v3"; + enable-active-high; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc3v3_m2_pcie_en>; + pinctrl-names = "default"; + startup-delay-us = <200000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc3v3_mini_pcie: vcc3v3-mini-pcie-regulator { + compatible = "regulator-fixed"; + regulator-name = "minipcie_3v3"; + enable-active-high; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc3v3_mini_pcie_en>; + pinctrl-names = "default"; + startup-delay-us = <5000>; + vin-supply = <&vcc5v0_sys>; + }; + + vcc5v0_usb20_host: vcc5v0-usb20-host-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_usb20_host"; + enable-active-high; + gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc5v0_usb20_host_en>; + pinctrl-names = "default"; + }; + + vcc5v0_usb30_host: vcc5v0-usb30-host-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_usb30_host"; + enable-active-high; + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc5v0_usb30_host_en>; + pinctrl-names = "default"; + }; + + vcc5v0_otg_vbus: vcc5v0-otg-vbus-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0_otg_vbus"; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&vcc5v0_otg_vbus_en>; + pinctrl-names = "default"; + }; +}; + +&combphy0 { + status = "okay"; +}; + +&combphy1 { + status = "okay"; +}; + +&combphy2 { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu1 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu2 { + cpu-supply = <&vdd_cpu>; +}; + +&cpu3 { + cpu-supply = <&vdd_cpu>; +}; + +&gpu { + mali-supply = <&vdd_gpu>; + status = "okay"; +}; + +&hdmi { + avdd-0v9-supply = <&vdda0v9_image>; + avdd-1v8-supply = <&vcca1v8_image>; + status = "okay"; +}; + +&hdmi_in { + hdmi_in_vp0: endpoint { + remote-endpoint = <&vp0_out_hdmi>; + }; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&hdmi_sound { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + vdd_cpu: regulator@1c { + compatible = "tcs,tcs4525"; + reg = <0x1c>; + fcs,suspend-voltage-selector = <1>; + regulator-name = "vdd_cpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-ramp-delay = <2300>; + vin-supply = <&vcc5v0_sys>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + rk809: pmic@20 { + compatible = "rockchip,rk809"; + reg = <0x20>; + interrupt-parent = <&gpio0>; + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; + assigned-clocks = <&cru I2S1_MCLKOUT_TX>; + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>; + #clock-cells = <1>; + clock-names = "mclk"; + clocks = <&cru I2S1_MCLKOUT_TX>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + rockchip,system-power-controller; + #sound-dai-cells = <0>; + vcc1-supply = <&vcc3v3_sys>; + vcc2-supply = <&vcc3v3_sys>; + vcc3-supply = <&vcc3v3_sys>; + vcc4-supply = <&vcc3v3_sys>; + vcc5-supply = <&vcc3v3_sys>; + vcc6-supply = <&vcc3v3_sys>; + vcc7-supply = <&vcc3v3_sys>; + vcc8-supply = <&vcc3v3_sys>; + vcc9-supply = <&vcc3v3_sys>; + wakeup-source; + + regulators { + vdd_logic: DCDC_REG1 { + regulator-name = "vdd_logic"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-name = "vdd_gpu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vdd_npu: DCDC_REG4 { + regulator-name = "vdd_npu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1350000>; + regulator-init-microvolt = <900000>; + regulator-ramp-delay = <6001>; + regulator-initial-mode = <0x2>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_1v8: DCDC_REG5 { + regulator-name = "vcc_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_image: LDO_REG1 { + regulator-name = "vdda0v9_image"; + regulator-boot-on; + regulator-always-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda_0v9: LDO_REG2 { + regulator-name = "vdda_0v9"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdda0v9_pmu: LDO_REG3 { + regulator-name = "vdda0v9_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <900000>; + }; + }; + + vccio_acodec: LDO_REG4 { + regulator-name = "vccio_acodec"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vccio_sd: LDO_REG5 { + regulator-name = "vccio_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_pmu: LDO_REG6 { + regulator-name = "vcc3v3_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcca_1v8: LDO_REG7 { + regulator-name = "vcca_1v8"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcca1v8_pmu: LDO_REG8 { + regulator-name = "vcca1v8_pmu"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca1v8_image: LDO_REG9 { + regulator-name = "vcca1v8_image"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc_3v3: SWITCH_REG1 { + regulator-name = "vcc_3v3"; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vcc3v3_sd: SWITCH_REG2 { + regulator-name = "vcc3v3_sd"; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + }; + }; +}; + +&i2s1_8ch { + rockchip,trcm-sync-tx-only; + status = "okay"; +}; + +&gmac0 { + phy-mode = "rgmii"; + clock_in_out = "output"; + + snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + /* Reset time is 20ms, 100ms for rtl8211f */ + snps,reset-delays-us = <0 20000 100000>; + + assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>; + assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>; + + pinctrl-names = "default"; + pinctrl-0 = <&gmac0_miim + &gmac0_tx_bus2 + &gmac0_rx_bus2 + &gmac0_rgmii_clk + &gmac0_rgmii_bus>; + + tx_delay = <0x22>; + rx_delay = <0x0e>; + + phy-handle = <&rgmii_phy0>; + status = "okay"; +}; + +&mdio0 { + rgmii_phy0: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + }; +}; + +&gmac1 { + phy-mode = "rgmii"; + clock_in_out = "output"; + + snps,reset-gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + /* Reset time is 20ms, 100ms for rtl8211f */ + snps,reset-delays-us = <0 20000 100000>; + + assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>; + assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>; + + pinctrl-names = "default"; + pinctrl-0 = <&gmac1m1_miim + &gmac1m1_tx_bus2 + &gmac1m1_rx_bus2 + &gmac1m1_rgmii_clk + &gmac1m1_rgmii_bus>; + + tx_delay = <0x21>; + rx_delay = <0x0e>; + + phy-handle = <&rgmii_phy1>; + status = "okay"; +}; + +&mdio1 { + rgmii_phy1: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + }; +}; + +&gic { + mbi-ranges = <94 31>, <229 31>, <289 31>; +}; + +&pcie30phy { + status = "okay"; +}; + +&pcie3x2 { + reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_m2_pcie>; + status = "okay"; +}; + +&pcie2x1 { + reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>; + disable-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_HIGH>; + vpcie3v3-supply = <&vcc3v3_mini_pcie>; + status = "okay"; +}; + +&pmu_io_domains { + pmuio2-supply = <&vcc3v3_pmu>; + vccio1-supply = <&vccio_acodec>; + vccio3-supply = <&vccio_sd>; + vccio4-supply = <&vcc_1v8>; + vccio5-supply = <&vcc_3v3>; + vccio6-supply = <&vcc_1v8>; + vccio7-supply = <&vcc_3v3>; + status = "okay"; +}; + +&pwm8 { + status = "okay"; +}; + +&pwm9 { + status = "disabled"; +}; + +&pwm10 { + status = "disabled"; +}; + +&pwm14 { + status = "disabled"; +}; + +&spi3 { + pinctrl-0 = <&spi3m1_pins>; + status = "disabled"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3m1_xfer>; + status = "disabled"; +}; + +&saradc { + vref-supply = <&vcca_1v8>; + status = "okay"; +}; + +&tsadc { + rockchip,hw-tshut-mode = <1>; + rockchip,hw-tshut-polarity = <0>; + status = "okay"; +}; + +&sdhci { + assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>, <&cru CCLK_EMMC>; + assigned-clock-rates = <200000000>, <24000000>, <200000000>; + bus-width = <8>; + max-frequency = <200000000>; + mmc-hs200-1_8v; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>; + supports-emmc; + status = "okay"; +}; + +&sdmmc0 { + max-frequency = <150000000>; + no-sdio; + no-mmc; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + disable-wp; + sd-uhs-sdr104; + vmmc-supply = <&vcc3v3_sd>; + vqmmc-supply = <&vccio_sd>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; + status = "okay"; +}; + +/* USB OTG/USB Host_1 USB 2.0 Comb */ +&usb2phy0 { + status = "okay"; +}; + +&usb2phy0_host { + phy-supply = <&vcc5v0_usb30_host>; + status = "okay"; +}; + +&usb2phy0_otg { + phy-supply = <&vcc5v0_otg_vbus>; + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; + +&usb_host0_ohci { + status = "okay"; +}; + +/* USB Host_2/USB Host_3 USB 2.0 Comb */ +&usb2phy1 { + status = "okay"; +}; + +&usb2phy1_host { + status = "okay"; +}; + +&usb2phy1_otg { + phy-supply = <&vcc5v0_usb20_host>; + status = "okay"; +}; + +&usb_host1_ehci { + status = "okay"; +}; + +&usb_host1_ohci { + status = "okay"; +}; + +/* MULTI_PHY0 For SATA0, USB3.0 OTG Only USB2.0 */ +&usb_host0_xhci { + phys = <&usb2phy0_otg>; + phy-names = "usb2-phy"; + extcon = <&usb2phy0>; + maximum-speed = "high-speed"; + dr_mode = "host"; + status = "okay"; +}; + +&sata0 { + status = "okay"; +}; + +/* USB3.0 Host */ +&usb_host1_xhci { + status = "okay"; +}; + +&vop { + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; + status = "okay"; +}; + +&vop_mmu { + status = "okay"; +}; + +&vp0 { + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { + reg = <ROCKCHIP_VOP2_EP_HDMI0>; + remote-endpoint = <&hdmi_in_vp0>; + }; +}; + +&pinctrl { + leds { + user_led_pin: user-status-led-pin { + rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + usb { + vcc5v0_usb20_host_en: vcc5v0-usb20-host-en { + rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc5v0_usb30_host_en: vcc5v0-usb30-host-en { + rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc5v0_otg_vbus_en: vcc5v0-otg-vbus-en { + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pcie { + vcc3v3_m2_pcie_en: vcc3v3-m2-pcie-en { + rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; + }; + + vcc3v3_mini_pcie_en: vcc3v3-mini-pcie-en { + rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; diff --git a/board/rockchip/evb_rk3568/MAINTAINERS b/board/rockchip/evb_rk3568/MAINTAINERS index 82a92b89fa..1cdeafcf79 100644 --- a/board/rockchip/evb_rk3568/MAINTAINERS +++ b/board/rockchip/evb_rk3568/MAINTAINERS @@ -7,6 +7,13 @@ F: configs/evb-rk3568_defconfig F: arch/arm/dts/rk3568-evb-boot.dtsi F: arch/arm/dts/rk3568-evb.dts
+Lubancat-2 +M: Andy Yan andyshrk@163.com +S: Maintained +F: configs/lubancat-2-rk3568_defconfig +F: arch/arm/dts/rk3568-lubancat-2.dts +F: arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi + NANOPI-R5C M: Tianling Shen cnsztl@gmail.com S: Maintained diff --git a/configs/lubancat-2-rk3568_defconfig b/configs/lubancat-2-rk3568_defconfig new file mode 100644 index 0000000000..b01d3bd2a1 --- /dev/null +++ b/configs/lubancat-2-rk3568_defconfig @@ -0,0 +1,85 @@ +CONFIG_ARM=y +CONFIG_SKIP_LOWLEVEL_INIT=y +CONFIG_COUNTER_FREQUENCY=24000000 +CONFIG_ARCH_ROCKCHIP=y +CONFIG_TEXT_BASE=0x00a00000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000 +CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2" +CONFIG_ROCKCHIP_RK3568=y +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_STACK_R_ADDR=0x600000 +CONFIG_SPL_STACK=0x400000 +CONFIG_DEBUG_UART_BASE=0xFE660000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_SYS_LOAD_ADDR=0xc00800 +CONFIG_DEBUG_UART=y +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_SPL_FIT_SIGNATURE=y +CONFIG_SPL_LOAD_FIT=y +CONFIG_LEGACY_IMAGE_FORMAT=y +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_DISPLAY_BOARDINFO_LATE=y +CONFIG_SPL_MAX_SIZE=0x40000 +CONFIG_SPL_PAD_TO=0x7f8000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x4000000 +CONFIG_SPL_BSS_MAX_SIZE=0x4000 +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SPL_STACK_R=y +CONFIG_SPL_ATF=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_GPT=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y +# CONFIG_SPL_DOS_PARTITION is not set +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIVE=y +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_SPL_REGMAP=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_CLK=y +CONFIG_ROCKCHIP_GPIO=y +CONFIG_SYS_I2C_ROCKCHIP=y +CONFIG_MISC=y +CONFIG_SUPPORT_EMMC_RPMB=y +CONFIG_MMC_DW=y +CONFIG_MMC_DW_ROCKCHIP=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_SDMA=y +CONFIG_MMC_SDHCI_ROCKCHIP=y +# CONFIG_SPI_FLASH is not set +CONFIG_PHY_ROCKCHIP_INNO_USB2=y +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y +CONFIG_SPL_PINCTRL=y +CONFIG_DM_PMIC=y +CONFIG_PMIC_RK8XX=y +CONFIG_REGULATOR_RK8XX=y +CONFIG_PWM_ROCKCHIP=y +CONFIG_SPL_RAM=y +CONFIG_BAUDRATE=1500000 +CONFIG_DEBUG_UART_SHIFT=2 +CONFIG_SYS_NS16550_MEM32=y +CONFIG_SYSRESET=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_GENERIC=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_GENERIC=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_ERRNO_STR=y +CONFIG_EFI_VAR_BUF_SIZE=16384 diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst index 49a0c5797a..31aeb85676 100644 --- a/doc/board/rockchip/rockchip.rst +++ b/doc/board/rockchip/rockchip.rst @@ -95,6 +95,7 @@ List of mainline supported Rockchip boards:
* rk3568 - Rockchip Evb-RK3568 (evb-rk3568) + - EmbedFire Lubancat 2 (lubancat-2-rk3568_defconfig) - Hardkernel ODROID-M1 (odroid-m1-rk3568) - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig) - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)