Re: [PATCH v3 1/2] spi: rockchip_sfc: Implement set_speed logic

On 2021/9/17 下午9:14, Jon Lin wrote:

Set clock related processing into set_speed logic. And Optimize printing format.

Tested-by: Chris Morgan macromorgan@hotmail.com Signed-off-by: Jon Lin jon.lin@rock-chips.com

Reviewed-by: Kever Yang kever.yang@rock-chips.com

Thanks, - Kever

---

Changes in v3:

• Remove useless headfile

• Fix misspelling

  drivers/spi/rockchip_sfc.c | 82 ++++++++++++++++++-------------------- 1 file changed, 39 insertions(+), 43 deletions(-)

diff --git a/drivers/spi/rockchip_sfc.c b/drivers/spi/rockchip_sfc.c index 4e2b861f22..94222df5ce 100644 --- a/drivers/spi/rockchip_sfc.c +++ b/drivers/spi/rockchip_sfc.c @@ -116,6 +116,7 @@

/* Master trigger */ #define SFC_DMA_TRIGGER 0x80 +#define SFC_DMA_TRIGGER_START 1

/* Src or Dst addr for master */ #define SFC_DMA_ADDR 0x84 @@ -163,14 +164,12 @@ #define SFC_DMA_TRANS_THRETHOLD (0x40)

/* Maximum clock values from datasheet suggest keeping clock value under

• • 150MHz. No minimum or average value is suggested, but the U-boot BSP driver
• • has a minimum of 10MHz and a default of 80MHz which seems reasonable.

• • 150MHz. No minimum or average value is suggested.
  */

-#define SFC_MIN_SPEED_HZ (10 * 1000 * 1000) -#define SFC_DEFAULT_SPEED_HZ (80 * 1000 * 1000) -#define SFC_MAX_SPEED_HZ (150 * 1000 * 1000) +#define SFC_MAX_SPEED (150 * 1000 * 1000)

struct rockchip_sfc {

• struct udevice *dev; void __iomem *regbase; struct clk hclk; struct clk clk;

@@ -197,8 +196,6 @@ static int rockchip_sfc_reset(struct rockchip_sfc *sfc) /* Still need to clear the masked interrupt from RISR */ writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);

• debug("reset\n");
• return err; }

@@ -261,15 +258,11 @@ static int rockchip_sfc_probe(struct udevice *bus) #if CONFIG_IS_ENABLED(CLK) ret = clk_enable(&sfc->hclk); if (ret)

• debug("Enable ahb clock fail %s: %d\n", bus->name, ret);
  

• dev_dbg(sfc->dev, "sfc Enable ahb clock fail %s: %d\n", bus->name, ret);
  
  

  ret = clk_enable(&sfc->clk); if (ret)

• debug("Enable clock fail for %s: %d\n", bus->name, ret);
  

• ret = clk_set_rate(&sfc->clk, SFC_DEFAULT_SPEED_HZ);
• if (ret)

• debug("Could not set sfc clock for %s: %d\n", bus->name, ret);
  

• dev_dbg(sfc->dev, "sfc Enable clock fail for %s: %d\n", bus->name, ret);
  

  #endif

  ret = rockchip_sfc_init(sfc);

@@ -278,7 +271,8 @@ static int rockchip_sfc_probe(struct udevice *bus)

sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc); sfc->version = rockchip_sfc_get_version(sfc);

• sfc->speed = SFC_DEFAULT_SPEED_HZ;

• sfc->max_freq = SFC_MAX_SPEED;

• sfc->dev = bus;

  return 0;

@@ -411,11 +405,11 @@ static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc, ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE; cmd |= plat->cs << SFC_CMD_CS_SHIFT;

• debug("addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n",

•      op->addr.nbytes, op->addr.buswidth,
  

•      op->dummy.nbytes, op->dummy.buswidth);
  

• debug("ctrl=%x cmd=%x addr=%llx len=%x\n",

•      ctrl, cmd, op->addr.val, len);
  

• dev_dbg(sfc->dev, "sfc addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n",

• op->addr.nbytes, op->addr.buswidth,
  

• op->dummy.nbytes, op->dummy.buswidth);
  

• dev_dbg(sfc->dev, "sfc ctrl=%x cmd=%x addr=%llx len=%x\n",

• ctrl, cmd, op->addr.val, len);
  
  

  writel(ctrl, sfc->regbase + SFC_CTRL); writel(cmd, sfc->regbase + SFC_CMD);

@@ -492,7 +486,7 @@ static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t d { writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR);

• writel(0x1, sfc->regbase + SFC_DMA_TRIGGER);

• writel(SFC_DMA_TRIGGER_START, sfc->regbase + SFC_DMA_TRIGGER);

  return len; }

@@ -500,7 +494,7 @@ static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t d static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc, const struct spi_mem_op *op, u32 len) {

• debug("xfer_poll len=%x\n", len);

• dev_dbg(sfc->dev, "sfc xfer_poll len=%x\n", len);

  if (op->data.dir == SPI_MEM_DATA_OUT) return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len);

@@ -516,7 +510,7 @@ static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc, void *dma_buf; int ret;

• debug("xfer_dma len=%x\n", len);

• dev_dbg(sfc->dev, "sfc xfer_dma len=%x\n", len);

  if (op->data.dir == SPI_MEM_DATA_OUT) { dma_buf = (void *)op->data.buf.out;

@@ -564,33 +558,16 @@ static int rockchip_sfc_exec_op(struct spi_slave *mem, u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize); int ret;

-#if CONFIG_IS_ENABLED(CLK)

• if (unlikely(mem->max_hz != sfc->speed)) {

• ret = clk_set_rate(&sfc->clk, clamp(mem->max_hz, (uint)SFC_MIN_SPEED_HZ,
  

• 				    (uint)SFC_MAX_SPEED_HZ));
  

• if (ret < 0) {
  

• 	printf("set_freq=%dHz fail, check if it's the cru support level\n",
  

• 	       mem->max_hz);
  

• 	return ret;
  

• }
  

• sfc->max_freq = mem->max_hz;
  

• sfc->speed = mem->max_hz;
  

• debug("set_freq=%dHz real_freq=%dHz\n", sfc->max_freq, sfc->speed);
  

• }

-#endif

• rockchip_sfc_adjust_op_work((struct spi_mem_op *)op);
• rockchip_sfc_xfer_setup(sfc, mem, op, len); if (len) {

• if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD)
  

• if (likely(sfc->use_dma) && len >= SFC_DMA_TRANS_THRETHOLD)
  ret = rockchip_sfc_xfer_data_dma(sfc, op, len);
  

  else ret = rockchip_sfc_xfer_data_poll(sfc, op, len);

  if (ret != len) {

• 	printf("xfer data failed ret %d dir %d\n", ret, op->data.dir);
  

• 	dev_err(sfc->dev, "xfer data failed ret %d dir %d\n", ret, op->data.dir);
  
  return -EIO;
  

  }

@@ -604,13 +581,32 @@ static int rockchip_sfc_adjust_op_size(struct spi_slave *mem, struct spi_mem_op struct rockchip_sfc *sfc = dev_get_plat(mem->dev->parent);

op->data.nbytes = min(op->data.nbytes, sfc->max_iosize);

• return 0; }

  static int rockchip_sfc_set_speed(struct udevice *bus, uint speed) {

• /* We set up speed later for each transmission.

• */
  

• struct rockchip_sfc *sfc = dev_get_plat(bus);
• if (speed > sfc->max_freq)

• speed = sfc->max_freq;
  

• if (speed == sfc->speed)

• return 0;
  

+#if CONFIG_IS_ENABLED(CLK)

• int ret = clk_set_rate(&sfc->clk, speed);
• if (ret < 0) {

• dev_err(sfc->dev, "set_freq=%dHz fail, check if it's the cru support level\n",
  

• 	speed);
  

• return ret;
  

• }
• sfc->speed = speed;

+#else

• dev_dbg(sfc->dev, "sfc failed, CLK not support\n");

+#endif return 0; }