Add pinctrl driver for i.MX8. The pads configuration is controlled by SCU, so need to ask SCU to configure pads through scfw API. Add pinctrl-scu to invoke sc_pad_set to configue pads. Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms which could directly configure pads from Acore side. Add CONFIG_PINCTRL_IMX8 as the built gate.
Signed-off-by: Ye Li ye.li@nxp.com Signed-off-by: Peng Fan peng.fan@nxp.com --- drivers/pinctrl/nxp/Kconfig | 18 ++++ drivers/pinctrl/nxp/Makefile | 2 + drivers/pinctrl/nxp/pinctrl-imx.c | 209 ++++++++++++++++++++----------------- drivers/pinctrl/nxp/pinctrl-imx.h | 16 +++ drivers/pinctrl/nxp/pinctrl-imx8.c | 42 ++++++++ drivers/pinctrl/nxp/pinctrl-scu.c | 72 +++++++++++++ 6 files changed, 266 insertions(+), 93 deletions(-) create mode 100644 drivers/pinctrl/nxp/pinctrl-imx8.c create mode 100644 drivers/pinctrl/nxp/pinctrl-scu.c
diff --git a/drivers/pinctrl/nxp/Kconfig b/drivers/pinctrl/nxp/Kconfig index b668359a0b..449ad47ebc 100644 --- a/drivers/pinctrl/nxp/Kconfig +++ b/drivers/pinctrl/nxp/Kconfig @@ -1,6 +1,9 @@ config PINCTRL_IMX bool
+config PINCTRL_IMX_SCU + bool + config PINCTRL_IMX5 bool "IMX5 pinctrl driver" depends on ARCH_MX5 && PINCTRL_FULL @@ -56,3 +59,18 @@ config PINCTRL_IMX7ULP is different from the linux one, this is a simple implementation, only parses the 'fsl,pins' property and configure related registers. + +config PINCTRL_IMX8 + bool "IMX8 pinctrl driver" + depends on ARCH_IMX8 && PINCTRL_FULL + select DEVRES + select PINCTRL_IMX + select PINCTRL_IMX_SCU + help + Say Y here to enable the imx8 pinctrl driver + + This provides a simple pinctrl driver for i.MX8 SoC familiy. + This feature depends on device tree configuration. This driver + is different from the linux one, this is a simple implementation, + only parses the 'fsl,pins' property and configure related + registers. diff --git a/drivers/pinctrl/nxp/Makefile b/drivers/pinctrl/nxp/Makefile index c763948376..310b3b3a2e 100644 --- a/drivers/pinctrl/nxp/Makefile +++ b/drivers/pinctrl/nxp/Makefile @@ -3,3 +3,5 @@ obj-$(CONFIG_PINCTRL_IMX5) += pinctrl-imx5.o obj-$(CONFIG_PINCTRL_IMX6) += pinctrl-imx6.o obj-$(CONFIG_PINCTRL_IMX7) += pinctrl-imx7.o obj-$(CONFIG_PINCTRL_IMX7ULP) += pinctrl-imx7ulp.o +obj-$(CONFIG_PINCTRL_IMX_SCU) += pinctrl-scu.o +obj-$(CONFIG_PINCTRL_IMX8) += pinctrl-imx8.o diff --git a/drivers/pinctrl/nxp/pinctrl-imx.c b/drivers/pinctrl/nxp/pinctrl-imx.c index 36e1e8983c..04ea82aba5 100644 --- a/drivers/pinctrl/nxp/pinctrl-imx.c +++ b/drivers/pinctrl/nxp/pinctrl-imx.c @@ -28,7 +28,9 @@ static int imx_pinctrl_set_state(struct udevice *dev, struct udevice *config)
dev_dbg(dev, "%s: %s\n", __func__, config->name);
- if (info->flags & SHARE_MUX_CONF_REG) + if (info->flags & IMX8_USE_SCU) + pin_size = SHARE_IMX8_PIN_SIZE; + else if (info->flags & SHARE_MUX_CONF_REG) pin_size = SHARE_FSL_PIN_SIZE; else pin_size = FSL_PIN_SIZE; @@ -58,112 +60,127 @@ static int imx_pinctrl_set_state(struct udevice *dev, struct udevice *config)
npins = size / pin_size;
- /* - * Refer to linux documentation for details: - * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt - */ - for (i = 0; i < npins; i++) { - mux_reg = pin_data[j++]; - - if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg) - mux_reg = -1; - - if (info->flags & SHARE_MUX_CONF_REG) { - conf_reg = mux_reg; - } else { - conf_reg = pin_data[j++]; - if (!(info->flags & ZERO_OFFSET_VALID) && !conf_reg) - conf_reg = -1; - } + if (info->flags & IMX8_USE_SCU) { + imx_pinctrl_scu_conf_pins(info, pin_data, npins); + } else { + /* + * Refer to linux documentation for details: + * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt + */ + for (i = 0; i < npins; i++) { + mux_reg = pin_data[j++];
- if ((mux_reg == -1) || (conf_reg == -1)) { - dev_err(dev, "Error mux_reg or conf_reg\n"); - devm_kfree(dev, pin_data); - return -EINVAL; - } + if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg) + mux_reg = -1;
- input_reg = pin_data[j++]; - mux_mode = pin_data[j++]; - input_val = pin_data[j++]; - config_val = pin_data[j++]; + if (info->flags & SHARE_MUX_CONF_REG) { + conf_reg = mux_reg; + } else { + conf_reg = pin_data[j++]; + if (!(info->flags & ZERO_OFFSET_VALID) && + !conf_reg) + conf_reg = -1; + }
- dev_dbg(dev, "mux_reg 0x%x, conf_reg 0x%x, input_reg 0x%x, " - "mux_mode 0x%x, input_val 0x%x, config_val 0x%x\n", - mux_reg, conf_reg, input_reg, mux_mode, input_val, - config_val); + if ((mux_reg == -1) || (conf_reg == -1)) { + dev_err(dev, "Error mux_reg or conf_reg\n"); + devm_kfree(dev, pin_data); + return -EINVAL; + }
- if (config_val & IMX_PAD_SION) - mux_mode |= IOMUXC_CONFIG_SION; + input_reg = pin_data[j++]; + mux_mode = pin_data[j++]; + input_val = pin_data[j++]; + config_val = pin_data[j++];
- config_val &= ~IMX_PAD_SION; + dev_dbg(dev, "mux_reg 0x%x, conf_reg 0x%x, " + "input_reg 0x%x, mux_mode 0x%x, " + "input_val 0x%x, config_val 0x%x\n", + mux_reg, conf_reg, input_reg, mux_mode, + input_val, config_val);
- /* Set Mux */ - if (info->flags & SHARE_MUX_CONF_REG) { - clrsetbits_le32(info->base + mux_reg, info->mux_mask, - mux_mode << mux_shift); - } else { - writel(mux_mode, info->base + mux_reg); - } + if (config_val & IMX_PAD_SION) + mux_mode |= IOMUXC_CONFIG_SION;
- dev_dbg(dev, "write mux: offset 0x%x val 0x%x\n", mux_reg, - mux_mode); + config_val &= ~IMX_PAD_SION;
- /* - * Set select input - * - * If the select input value begins with 0xff, it's a quirky - * select input and the value should be interpreted as below. - * 31 23 15 7 0 - * | 0xff | shift | width | select | - * It's used to work around the problem that the select - * input for some pin is not implemented in the select - * input register but in some general purpose register. - * We encode the select input value, width and shift of - * the bit field into input_val cell of pin function ID - * in device tree, and then decode them here for setting - * up the select input bits in general purpose register. - */ + /* Set Mux */ + if (info->flags & SHARE_MUX_CONF_REG) { + clrsetbits_le32(info->base + mux_reg, + info->mux_mask, + mux_mode << mux_shift); + } else { + writel(mux_mode, info->base + mux_reg); + } + + dev_dbg(dev, "write mux: offset 0x%x val 0x%x\n", + mux_reg, mux_mode);
- if (input_val >> 24 == 0xff) { - u32 val = input_val; - u8 select = val & 0xff; - u8 width = (val >> 8) & 0xff; - u8 shift = (val >> 16) & 0xff; - u32 mask = ((1 << width) - 1) << shift; - /* - * The input_reg[i] here is actually some IOMUXC general - * purpose register, not regular select input register. - */ - val = readl(info->base + input_reg); - val &= ~mask; - val |= select << shift; - writel(val, info->base + input_reg); - } else if (input_reg) { /* - * Regular select input register can never be at offset - * 0, and we only print register value for regular case. + * Set select input + * + * If the select input value begins with 0xff, + * it's a quirky select input and the value should + * be interpreted as below. + * 31 23 15 7 0 + * | 0xff | shift | width | select | + * It's used to work around the problem that the + * select input for some pin is not implemented in + * the select input register but in some general + * purpose register. We encode the select input + * value, width and shift of the bit field into + * input_val cell of pin function ID in device tree, + * and then decode them here for setting up the select + * input bits in general purpose register. */ - if (info->input_sel_base) - writel(input_val, info->input_sel_base + - input_reg); - else - writel(input_val, info->base + input_reg); - - dev_dbg(dev, "select_input: offset 0x%x val 0x%x\n", - input_reg, input_val); - }
- /* Set config */ - if (!(config_val & IMX_NO_PAD_CTL)) { - if (info->flags & SHARE_MUX_CONF_REG) { - clrsetbits_le32(info->base + conf_reg, - ~info->mux_mask, config_val); - } else { - writel(config_val, info->base + conf_reg); + if (input_val >> 24 == 0xff) { + u32 val = input_val; + u8 select = val & 0xff; + u8 width = (val >> 8) & 0xff; + u8 shift = (val >> 16) & 0xff; + u32 mask = ((1 << width) - 1) << shift; + /* + * The input_reg[i] here is actually some + * IOMUXC general purpose register, not + * regular select input register. + */ + val = readl(info->base + input_reg); + val &= ~mask; + val |= select << shift; + writel(val, info->base + input_reg); + } else if (input_reg) { + /* + * Regular select input register can never be + * at offset 0, and we only print register + * value for regular case. + */ + if (info->input_sel_base) + writel(input_val, + info->input_sel_base + + input_reg); + else + writel(input_val, + info->base + input_reg); + + dev_dbg(dev, "select_input: offset 0x%x val " + "0x%x\n", input_reg, input_val); }
- dev_dbg(dev, "write config: offset 0x%x val 0x%x\n", - conf_reg, config_val); + /* Set config */ + if (!(config_val & IMX_NO_PAD_CTL)) { + if (info->flags & SHARE_MUX_CONF_REG) { + clrsetbits_le32(info->base + conf_reg, + ~info->mux_mask, + config_val); + } else { + writel(config_val, + info->base + conf_reg); + } + + dev_dbg(dev, "write config: offset 0x%x val " + "0x%x\n", conf_reg, config_val); + } } }
@@ -193,6 +210,9 @@ int imx_pinctrl_probe(struct udevice *dev, priv->dev = dev; priv->info = info;
+ if (info->flags & IMX8_USE_SCU) + return 0; + addr = fdtdec_get_addr_size(gd->fdt_blob, dev_of_offset(dev), "reg", &size);
@@ -238,6 +258,9 @@ int imx_pinctrl_remove(struct udevice *dev) struct imx_pinctrl_priv *priv = dev_get_priv(dev); struct imx_pinctrl_soc_info *info = priv->info;
+ if (info->flags & IMX8_USE_SCU) + return 0; + if (info->input_sel_base) unmap_sysmem(info->input_sel_base); if (info->base) diff --git a/drivers/pinctrl/nxp/pinctrl-imx.h b/drivers/pinctrl/nxp/pinctrl-imx.h index b0032455b7..947975ee72 100644 --- a/drivers/pinctrl/nxp/pinctrl-imx.h +++ b/drivers/pinctrl/nxp/pinctrl-imx.h @@ -40,13 +40,29 @@ extern const struct pinctrl_ops imx_pinctrl_ops; #define FSL_PIN_SIZE 24 #define SHARE_FSL_PIN_SIZE 20
+/* Each pin on imx8qm/qxp consists of 2 u32 PIN_FUNC_ID and 1 u32 CONFIG */ +#define SHARE_IMX8_PIN_SIZE 12 + #define SHARE_MUX_CONF_REG 0x1 #define ZERO_OFFSET_VALID 0x2 #define CONFIG_IBE_OBE 0x4 +#define IMX8_USE_SCU 0x8
#define IOMUXC_CONFIG_SION (0x1 << 4)
int imx_pinctrl_probe(struct udevice *dev, struct imx_pinctrl_soc_info *info);
int imx_pinctrl_remove(struct udevice *dev); + +#ifdef CONFIG_PINCTRL_IMX_SCU +int imx_pinctrl_scu_conf_pins(struct imx_pinctrl_soc_info *info, + u32 *pin_data, int npins); +#else +static inline int imx_pinctrl_scu_conf_pins(struct imx_pinctrl_soc_info *info, + u32 *pin_data, int npins) +{ + return 0; +} +#endif + #endif /* __DRIVERS_PINCTRL_IMX_H */ diff --git a/drivers/pinctrl/nxp/pinctrl-imx8.c b/drivers/pinctrl/nxp/pinctrl-imx8.c new file mode 100644 index 0000000000..26bc160318 --- /dev/null +++ b/drivers/pinctrl/nxp/pinctrl-imx8.c @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + */ + +#include <common.h> +#include <dm/device.h> +#include <dm/pinctrl.h> + +#include "pinctrl-imx.h" + +DECLARE_GLOBAL_DATA_PTR; + +static struct imx_pinctrl_soc_info imx8_pinctrl_soc_info = { + .flags = IMX8_USE_SCU, +}; + +static int imx8_pinctrl_probe(struct udevice *dev) +{ + struct imx_pinctrl_soc_info *info = + (struct imx_pinctrl_soc_info *)dev_get_driver_data(dev); + + info->base = (void *)gd->arch.ipc_channel_handle; + + return imx_pinctrl_probe(dev, info); +} + +static const struct udevice_id imx8_pinctrl_match[] = { + { .compatible = "fsl,imx8qxp-iomuxc", .data = (ulong)&imx8_pinctrl_soc_info }, + { /* sentinel */ } +}; + +U_BOOT_DRIVER(imx8_pinctrl) = { + .name = "imx8_pinctrl", + .id = UCLASS_PINCTRL, + .of_match = of_match_ptr(imx8_pinctrl_match), + .probe = imx8_pinctrl_probe, + .remove = imx_pinctrl_remove, + .priv_auto_alloc_size = sizeof(struct imx_pinctrl_priv), + .ops = &imx_pinctrl_ops, + .flags = DM_FLAG_PRE_RELOC, +}; diff --git a/drivers/pinctrl/nxp/pinctrl-scu.c b/drivers/pinctrl/nxp/pinctrl-scu.c new file mode 100644 index 0000000000..ca9222feeb --- /dev/null +++ b/drivers/pinctrl/nxp/pinctrl-scu.c @@ -0,0 +1,72 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2018 NXP + */ + +#include <common.h> +#include <errno.h> +#include <linux/bitops.h> +#include <asm/io.h> +#include <asm/arch/sci/sci.h> + +#include "pinctrl-imx.h" + +#define PADRING_IFMUX_EN_SHIFT 31 +#define PADRING_IFMUX_EN_MASK BIT(31) +#define PADRING_GP_EN_SHIFT 30 +#define PADRING_GP_EN_MASK BIT(30) +#define PADRING_IFMUX_SHIFT 27 +#define PADRING_IFMUX_MASK GENMASK(29, 27) + +static int imx_pinconf_scu_set(struct imx_pinctrl_soc_info *info, u32 pin_id, + u32 mux, u32 val) +{ + sc_err_t err; + sc_ipc_t ipchndl = (sc_ipc_t)info->base; + + /* + * Mux should be done in pmx set, but we do not have a good api + * to handle that in scfw, so config it in pad conf func + */ + + if (ipchndl == 0) { + puts("IPC handle not initialized!\n"); + return -EIO; + } + + val |= PADRING_IFMUX_EN_MASK; + val |= PADRING_GP_EN_MASK; + val |= (mux << PADRING_IFMUX_SHIFT) & PADRING_IFMUX_MASK; + + err = sc_pad_set(ipchndl, pin_id, val); + + if (err != SC_ERR_NONE) + return -EIO; + + return 0; +} + +int imx_pinctrl_scu_conf_pins(struct imx_pinctrl_soc_info *info, u32 *pin_data, + int npins) +{ + int pin_id, mux, config_val; + int i, j = 0; + int ret; + + /* + * Refer to linux documentation for details: + * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt + */ + for (i = 0; i < npins; i++) { + pin_id = pin_data[j++]; + mux = pin_data[j++]; + config_val = pin_data[j++]; + + ret = imx_pinconf_scu_set(info, pin_id, mux, config_val); + if (ret) + printf("Set pin %d, mux %d, val %d, error\n", pin_id, + mux, config_val); + } + + return 0; +}