Add H6 SPI addresses and masks (since H6 memory map is totally different). Tested on Pine H64 rev B with Winbond W25Q128FW,
Signed-off-by: Marek Kraus gamelaster@outlook.com ---
arch/arm/mach-sunxi/Kconfig | 2 +- arch/arm/mach-sunxi/spl_spi_sunxi.c | 123 ++++++++++++++++++++++++++++-------- configs/pine_h64_defconfig | 1 + 3 files changed, 98 insertions(+), 28 deletions(-)
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig index 74e234cded..81b5948454 100644 --- a/arch/arm/mach-sunxi/Kconfig +++ b/arch/arm/mach-sunxi/Kconfig @@ -972,7 +972,7 @@ config SPL_STACK_R_ADDR
config SPL_SPI_SUNXI bool "Support for SPI Flash on Allwinner SoCs in SPL" - depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I + depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN50I_H6 help Enable support for SPI Flash. This option allows SPL to read from sunxi SPI Flash. It uses the same method as the boot ROM, so does diff --git a/arch/arm/mach-sunxi/spl_spi_sunxi.c b/arch/arm/mach-sunxi/spl_spi_sunxi.c index 043d9f6ead..cdf6d53ec5 100644 --- a/arch/arm/mach-sunxi/spl_spi_sunxi.c +++ b/arch/arm/mach-sunxi/spl_spi_sunxi.c @@ -28,7 +28,7 @@ * A10/A13/A20 (sun4i variant) and everything else (sun6i variant). * Both of them are supported. * - * The pin mixing part is SoC specific and only A10/A13/A20/H3/A64 are + * The pin mixing part is SoC specific and only A10/A13/A20/H3/A64/H6 are * supported at the moment. */
@@ -70,6 +70,25 @@ #define SUN6I_TCR_XCH BIT(31)
/*****************************************************************************/ +/* SUN50I_H6 variant of the SPI controller */ +/*****************************************************************************/ + +#define SUN50I_H6_SPI0_CCTL (0x05010000 + 0x24) +#define SUN50I_H6_SPI0_GCR (0x05010000 + 0x04) +#define SUN50I_H6_SPI0_TCR (0x05010000 + 0x08) +#define SUN50I_H6_SPI0_FIFO_STA (0x05010000 + 0x1C) +#define SUN50I_H6_SPI0_MBC (0x05010000 + 0x30) +#define SUN50I_H6_SPI0_MTC (0x05010000 + 0x34) +#define SUN50I_H6_SPI0_BCC (0x05010000 + 0x38) +#define SUN50I_H6_SPI0_TXD (0x05010000 + 0x200) +#define SUN50I_H6_SPI0_RXD (0x05010000 + 0x300) + +#define SUN50I_H6_SPI_GATING_REG (0x03001000 + 0x96C) +#define SUN50I_H6_SPI0_RST BIT(16) +#define SUN50I_H6_SPI0_GATING_CLK BIT(0) +#define SUN50I_H6_CCU_SPI0_CLK (0x03001000 + 0x940) + +/*****************************************************************************/
#define CCM_AHB_GATING0 (0x01C20000 + 0x60) #define CCM_SPI0_CLK (0x01C20000 + 0xA0) @@ -85,19 +104,29 @@
/* * Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting - * from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3. + * from SPI Flash, H6 using PC0,PC2,PC3,PC5 , everything else is using + * pins PC0,PC1,PC2,PC3. */ static void spi0_pinmux_setup(unsigned int pin_function) { unsigned int pin;
- for (pin = SUNXI_GPC(0); pin <= SUNXI_GPC(2); pin++) - sunxi_gpio_set_cfgpin(pin, pin_function);
- if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I)) - sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function); - else + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) { + sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function); + sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function); sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function); + sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function); + } else { + for (pin = SUNXI_GPC(0); pin <= SUNXI_GPC(2); pin++) + sunxi_gpio_set_cfgpin(pin, pin_function); + + if (IS_ENABLED(CONFIG_MACH_SUN4I) || + IS_ENABLED(CONFIG_MACH_SUN7I)) + sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function); + else + sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function); + } }
/* @@ -106,26 +135,43 @@ static void spi0_pinmux_setup(unsigned int pin_function) static void spi0_enable_clock(void) { /* Deassert SPI0 reset on SUN6I */ - if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) + setbits_le32(SUN50I_H6_SPI_GATING_REG, + SUN50I_H6_SPI0_RST); + else if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) setbits_le32(SUN6I_BUS_SOFT_RST_REG0, (1 << AHB_RESET_SPI0_SHIFT));
/* Open the SPI0 gate */ - setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0)); + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) + setbits_le32(SUN50I_H6_SPI_GATING_REG, + SUN50I_H6_SPI0_GATING_CLK); + else + setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
/* Divide by 4 */ - writel(SPI0_CLK_DIV_BY_4, IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ? - SUN6I_SPI0_CCTL : SUN4I_SPI0_CCTL); + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) + writel(SPI0_CLK_DIV_BY_4, SUN50I_H6_SPI0_CCTL); + else + writel(SPI0_CLK_DIV_BY_4, IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ? + SUN6I_SPI0_CCTL : SUN4I_SPI0_CCTL); + /* 24MHz from OSC24M */ - writel((1 << 31), CCM_SPI0_CLK); + writel((1 << 31), IS_ENABLED(CONFIG_MACH_SUN50I_H6) ? + SUN50I_H6_CCU_SPI0_CLK : CCM_SPI0_CLK);
- if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) { + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) || + IS_ENABLED(CONFIG_MACH_SUN50I_H6)) { /* Enable SPI in the master mode and do a soft reset */ - setbits_le32(SUN6I_SPI0_GCR, SUN6I_CTL_MASTER | - SUN6I_CTL_ENABLE | - SUN6I_CTL_SRST); + setbits_le32(IS_ENABLED(CONFIG_MACH_SUN50I_H6) ? + SUN50I_H6_SPI0_GCR : SUN6I_SPI0_GCR, + SUN6I_CTL_MASTER | + SUN6I_CTL_ENABLE | + SUN6I_CTL_SRST); + /* Wait for completion */ - while (readl(SUN6I_SPI0_GCR) & SUN6I_CTL_SRST) + while (readl(IS_ENABLED(CONFIG_MACH_SUN50I_H6) ? + SUN50I_H6_SPI0_GCR : SUN6I_SPI0_GCR) & SUN6I_CTL_SRST) ; } else { /* Enable SPI in the master mode and reset FIFO */ @@ -139,22 +185,33 @@ static void spi0_enable_clock(void) static void spi0_disable_clock(void) { /* Disable the SPI0 controller */ - if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) - clrbits_le32(SUN6I_SPI0_GCR, SUN6I_CTL_MASTER | - SUN6I_CTL_ENABLE); + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) || + IS_ENABLED(CONFIG_MACH_SUN50I_H6)) + clrbits_le32(IS_ENABLED(CONFIG_MACH_SUN50I_H6) ? + SUN50I_H6_SPI0_GCR : SUN6I_SPI0_GCR, + SUN6I_CTL_MASTER | + SUN6I_CTL_ENABLE); else clrbits_le32(SUN4I_SPI0_CTL, SUN4I_CTL_MASTER | SUN4I_CTL_ENABLE);
/* Disable the SPI0 clock */ - writel(0, CCM_SPI0_CLK); + writel(0, IS_ENABLED(CONFIG_MACH_SUN50I_H6) ? + SUN50I_H6_CCU_SPI0_CLK : CCM_SPI0_CLK);
/* Close the SPI0 gate */ - clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0)); + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) + clrbits_le32(SUN50I_H6_SPI_GATING_REG, + SUN50I_H6_SPI0_GATING_CLK); + else + clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
/* Assert SPI0 reset on SUN6I */ - if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) - clrbits_le32(SUN6I_BUS_SOFT_RST_REG0, + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) + setbits_le32(SUN50I_H6_SPI_GATING_REG, + SUN50I_H6_SPI0_RST); + else if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + setbits_le32(SUN6I_BUS_SOFT_RST_REG0, (1 << AHB_RESET_SPI0_SHIFT)); }
@@ -162,7 +219,7 @@ static void spi0_init(void) { unsigned int pin_function = SUNXI_GPC_SPI0;
- if (IS_ENABLED(CONFIG_MACH_SUN50I)) + if (IS_ENABLED(CONFIG_MACH_SUN50I) || IS_ENABLED(CONFIG_MACH_SUN50I_H6)) pin_function = SUN50I_GPC_SPI0;
spi0_pinmux_setup(pin_function); @@ -173,7 +230,9 @@ static void spi0_deinit(void) { /* New SoCs can disable pins, older could only set them as input */ unsigned int pin_function = SUNXI_GPIO_INPUT; - if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) + + if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) || + IS_ENABLED(CONFIG_MACH_SUN50I_H6)) pin_function = SUNXI_GPIO_DISABLE;
spi0_disable_clock(); @@ -233,7 +292,17 @@ static void spi0_read_data(void *buf, u32 addr, u32 len) if (chunk_len > SPI_READ_MAX_SIZE) chunk_len = SPI_READ_MAX_SIZE;
- if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) { + if (IS_ENABLED(CONFIG_MACH_SUN50I_H6)) { + sunxi_spi0_read_data(buf8, addr, chunk_len, + SUN50I_H6_SPI0_TCR, + SUN6I_TCR_XCH, + SUN50I_H6_SPI0_FIFO_STA, + SUN50I_H6_SPI0_TXD, + SUN50I_H6_SPI0_RXD, + SUN50I_H6_SPI0_MBC, + SUN50I_H6_SPI0_MTC, + SUN50I_H6_SPI0_BCC); + } else if (IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I)) { sunxi_spi0_read_data(buf8, addr, chunk_len, SUN6I_SPI0_TCR, SUN6I_TCR_XCH, diff --git a/configs/pine_h64_defconfig b/configs/pine_h64_defconfig index e34f4fd1e4..baddc33abb 100644 --- a/configs/pine_h64_defconfig +++ b/configs/pine_h64_defconfig @@ -6,6 +6,7 @@ CONFIG_MMC0_CD_PIN="PF6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 # CONFIG_PSCI_RESET is not set CONFIG_NR_DRAM_BANKS=1 +CONFIG_SPL_SPI_SUNXI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set # CONFIG_CMD_FLASH is not set # CONFIG_SPL_DOS_PARTITION is not set