We have a requirement to wait a period of time before enabling the DDR controller
Signed-off-by: Matthew McClintock msm@freescale.com --- nand_spl/board/freescale/p1023rds/Makefile | 6 +++++- nand_spl/board/freescale/p1023rds/nand_boot.c | 14 ++++++++++++-- 2 files changed, 17 insertions(+), 3 deletions(-)
diff --git a/nand_spl/board/freescale/p1023rds/Makefile b/nand_spl/board/freescale/p1023rds/Makefile index 168e868..da43521 100644 --- a/nand_spl/board/freescale/p1023rds/Makefile +++ b/nand_spl/board/freescale/p1023rds/Makefile @@ -34,7 +34,8 @@ CFLAGS += -DCONFIG_NAND_SPL
SOBJS = start.o resetvec.o COBJS = cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \ - nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o + nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o \ + ../common.o
SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c)) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) @@ -114,6 +115,9 @@ ifneq ($(OBJTREE), $(SRCTREE)) $(obj)nand_boot.c: @rm -f $(obj)nand_boot.c ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c +$(obj)../common.c: + @rm -f $(obj)../common.c + ln -s $(SRCTREE)/nand_spl/board/freescale/common.c $(obj)../common.c endif
######################################################################### diff --git a/nand_spl/board/freescale/p1023rds/nand_boot.c b/nand_spl/board/freescale/p1023rds/nand_boot.c index 0065c87..9309936 100644 --- a/nand_spl/board/freescale/p1023rds/nand_boot.c +++ b/nand_spl/board/freescale/p1023rds/nand_boot.c @@ -25,6 +25,7 @@ #include <asm/io.h> #include <nand.h> #include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h>
/* Fixed sdram init -- doesn't use serial presence detect. */ void sdram_init(void) @@ -53,12 +54,21 @@ void sdram_init(void) out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL); out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1); out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2); - out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL); + /* Set, but do not enable the memory */ + out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN); + + asm volatile("sync;isync"); + udelay(500); + + /* Let the controller go */ + out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); }
+u32 bus_clk; + void board_init_f(ulong bootflag) { - u32 plat_ratio, bus_clk; + u32 plat_ratio; ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
/* initialize selected port with appropriate baud rate */