-----Original Message----- From: Valentin Longchamp [mailto:valentin.longchamp@keymile.com] Sent: Friday, April 08, 2011 6:18 PM To: u-boot@lists.denx.de Cc: holger.brunck@keymile.com; hs@denx.de; Wolfgang Denk; Detlev Zundel; Prafulla Wadaskar; Valentin Longchamp Subject: [PATCH] arm/km: change default settings for egiga on mgcoge3un
From: Holger Brunck holger.brunck@keymile.com
The reason we need this is that we have the gig port on mgcoge3un connected using a back-to-back pair of PHYs. There are no magnetics and because of that the port has to be run with a fixd configuration and auto-negotiation must be disabled. In the default mode the egiga driver uses autoneg to determine port speed - which defaults to 1G (we need 100M full duplex).
Signed-off-by: Holger Brunck holger.brunck@keymile.com Acked-by: Heiko Schocher hs@denx.de cc: Wolfgang Denk wd@denx.de cc: Detlev Zundel dzu@denx.de cc: Prafulla Wadaskar prafulla@marvell.com cc: Valentin Longchamp valentin.longchamp@keymile.com Signed-off-by: Valentin Longchamp valentin.longchamp@keymile.com
drivers/net/mvgbe.h | 2 ++ include/configs/mgcoge3un.h | 25 +++++++++++++++++++++++++ 2 files changed, 27 insertions(+), 0 deletions(-)
diff --git a/drivers/net/mvgbe.h b/drivers/net/mvgbe.h index 3de98d0..d8a5429 100644 --- a/drivers/net/mvgbe.h +++ b/drivers/net/mvgbe.h @@ -84,6 +84,7 @@ MVGBE_TX_BURST_SIZE_16_64BIT)
/* Default port serial control value */ +#ifndef PORT_SERIAL_CONTROL_VALUE #define PORT_SERIAL_CONTROL_VALUE ( \ MVGBE_FORCE_LINK_PASS | \ MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \ @@ -101,6 +102,7 @@ MVGBE_CLR_EXT_LOOPBACK | \ MVGBE_SET_FULL_DUPLEX_MODE | \ MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX) +#endif
/* Tx WRR confoguration macros */ #define PORT_MAX_TRAN_UNIT 0x24 /* MTU register (default) 9KByte */ diff --git a/include/configs/mgcoge3un.h b/include/configs/mgcoge3un.h index da5935b..c7f9056 100644 --- a/include/configs/mgcoge3un.h +++ b/include/configs/mgcoge3un.h @@ -48,6 +48,31 @@ #define KM_ENV_BUS "pca9547:70:d" /* I2C2 (Mux-Port 5)*/
/*
- mgcoge3un has a fixed link to the marvell switch
- with 100MB full duplex and autoneg off, for this
- reason we have to change the default settings
- */
+#define PORT_SERIAL_CONTROL_VALUE ( \
- MVGBE_FORCE_LINK_PASS | \
- MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \
- MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \
- MVGBE_ADV_NO_FLOW_CTRL | \
- MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \
- MVGBE_FORCE_BP_MODE_NO_JAM | \
- (1 << 9) /* Reserved bit has to be 1 */ | \
- MVGBE_DO_NOT_FORCE_LINK_FAIL | \
- MVGBE_DIS_AUTO_NEG_SPEED_GMII | \
- MVGBE_DTE_ADV_0 | \
- MVGBE_MIIPHY_MAC_MODE | \
- MVGBE_AUTO_NEG_NO_CHANGE | \
- MVGBE_MAX_RX_PACKET_1552BYTE | \
- MVGBE_CLR_EXT_LOOPBACK | \
- MVGBE_SET_FULL_DUPLEX_MODE | \
- MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\
- MVGBE_SET_GMII_SPEED_TO_10_100 |\
- MVGBE_SET_MII_SPEED_TO_100)
+/*
- Default environment variables
*/ #define CONFIG_EXTRA_ENV_SETTINGS
Acked-by: Prafulla Wadaskar Prafulla@marvell.com
Regards.. Prafulla . .
\
-- 1.7.0.5