Hi Fabio,
On 15/08/2014 06:00, Fabio Estevam wrote:
From: Fabio Estevam fabio.estevam@freescale.com
Use the latest DDR initialization values suggested by the FSL hardware team.
While at it, add some comments for clarification.
Signed-off-by: Fabio Estevam fabio.estevam@freescale.com
board/freescale/mx6sxsabresd/imximage.cfg | 89 ++++++++++++++++++++----------- 1 file changed, 58 insertions(+), 31 deletions(-)
diff --git a/board/freescale/mx6sxsabresd/imximage.cfg b/board/freescale/mx6sxsabresd/imximage.cfg index 406dece..c862617 100644 --- a/board/freescale/mx6sxsabresd/imximage.cfg +++ b/board/freescale/mx6sxsabresd/imximage.cfg @@ -30,6 +30,7 @@ BOOT_FROM sd
- value value to be stored in the register
*/
+/* Enable all clocks */ DATA 4 0x020c4068 0xffffffff DATA 4 0x020c406c 0xffffffff DATA 4 0x020c4070 0xffffffff @@ -39,46 +40,69 @@ DATA 4 0x020c407c 0xffffffff DATA 4 0x020c4080 0xffffffff DATA 4 0x020c4084 0xffffffff
+/* IOMUX - DDR IO Type */ DATA 4 0x020e0618 0x000c0000 DATA 4 0x020e05fc 0x00000000
+/* Clock */ DATA 4 0x020e032c 0x00000030
-DATA 4 0x020e0300 0x00000030 -DATA 4 0x020e02fc 0x00000030 -DATA 4 0x020e05f4 0x00000030 -DATA 4 0x020e0340 0x00000030 +/* Address */ +DATA 4 0x020e0300 0x00000020 +DATA 4 0x020e02fc 0x00000020 +DATA 4 0x020e05f4 0x00000020
+/* Control */ +DATA 4 0x020e0340 0x00000020
DATA 4 0x020e0320 0x00000000 -DATA 4 0x020e0310 0x00000030 -DATA 4 0x020e0314 0x00000030 -DATA 4 0x020e0614 0x00000030 +DATA 4 0x020e0310 0x00000020 +DATA 4 0x020e0314 0x00000020 +DATA 4 0x020e0614 0x00000020
+/* Data Strobe */ DATA 4 0x020e05f8 0x00020000 -DATA 4 0x020e0330 0x00000030 -DATA 4 0x020e0334 0x00000030 -DATA 4 0x020e0338 0x00000030 -DATA 4 0x020e033c 0x00000030 +DATA 4 0x020e0330 0x00000028 +DATA 4 0x020e0334 0x00000028 +DATA 4 0x020e0338 0x00000028 +DATA 4 0x020e033c 0x00000028
+/* Data */ DATA 4 0x020e0608 0x00020000 -DATA 4 0x020e060c 0x00000030 -DATA 4 0x020e0610 0x00000030 -DATA 4 0x020e061c 0x00000030 -DATA 4 0x020e0620 0x00000030 -DATA 4 0x020e02ec 0x00000030 -DATA 4 0x020e02f0 0x00000030 -DATA 4 0x020e02f4 0x00000030 -DATA 4 0x020e02f8 0x00000030 +DATA 4 0x020e060c 0x00000028 +DATA 4 0x020e0610 0x00000028 +DATA 4 0x020e061c 0x00000028 +DATA 4 0x020e0620 0x00000028 +DATA 4 0x020e02ec 0x00000028 +DATA 4 0x020e02f0 0x00000028 +DATA 4 0x020e02f4 0x00000028 +DATA 4 0x020e02f8 0x00000028
+/* Calibrations - ZQ */ DATA 4 0x021b0800 0xa1390003 -DATA 4 0x021b080c 0x00270025 -DATA 4 0x021b0810 0x001B001E -DATA 4 0x021b083c 0x4144013C -DATA 4 0x021b0840 0x01300128 -DATA 4 0x021b0848 0x4044464A -DATA 4 0x021b0850 0x3A383C34
+/* Write leveling */ +DATA 4 0x021b080c 0x00290025 +DATA 4 0x021b0810 0x00220022
+/* DQS Read Gate */ +DATA 4 0x021b083c 0x41480144 +DATA 4 0x021b0840 0x01340130
+/* Read/Write Delay */ +DATA 4 0x021b0848 0x3C3E4244 +DATA 4 0x021b0850 0x34363638
+/* Read data bit delay */ DATA 4 0x021b081c 0x33333333 DATA 4 0x021b0820 0x33333333 DATA 4 0x021b0824 0x33333333 DATA 4 0x021b0828 0x33333333
+/* Complete calibration by forced measurement */ DATA 4 0x021b08b8 0x00000800
+/* MMDC init - DDR3, 64-bit mode, only MMDC0 is initiated */ DATA 4 0x021b0004 0x0002002d DATA 4 0x021b0008 0x00333030 DATA 4 0x021b000c 0x676b52f3 @@ -90,16 +114,19 @@ DATA 4 0x021b002c 0x000026d2 DATA 4 0x021b0030 0x006b1023 DATA 4 0x021b0040 0x0000005f DATA 4 0x021b0000 0x84190000
+/* Initialize MT41K256M16HA-125 - MR2 */ DATA 4 0x021b001c 0x04008032 +/* MR3 */ DATA 4 0x021b001c 0x00008033 -DATA 4 0x021b001c 0x00068031 +/* MR1 */ +DATA 4 0x021b001c 0x00048031 +/* MR0 */ DATA 4 0x021b001c 0x05208030 +/* DDR device ZQ calibration */ DATA 4 0x021b001c 0x04008040
+/* Final DDR setup, before operation start */ DATA 4 0x021b0020 0x00000800 DATA 4 0x021b0818 0x00011117 DATA 4 0x021b001c 0x00000000
-DATA 4 0x021b083c 0x41400138 -DATA 4 0x021b0840 0x012C011C -DATA 4 0x021b0848 0x3C3C4044 -DATA 4 0x021b0850 0x34343638
Applied to u-boot-imx, thanks !
Best regards, Stefano Babic