From: Jagan Teki jagan@amarulasolutions.com
Use CONFIG_DM_ETH and remove board_eth_init code from board files.
Cc: Joe Hershberger joe.hershberger@ni.com Cc: Peng Fan peng.fan@nxp.com Cc: Stefano Babic sbabic@denx.de Cc: Michael Trimarchi michael@amarulasolutions.com Signed-off-by: Jagan Teki jagan@amarulasolutions.com --- arch/arm/cpu/armv7/mx6/Kconfig | 1 + board/engicam/icorem6/icorem6.c | 71 ------------------------------------ configs/imx6qdl_icore_mmc_defconfig | 1 - configs/imx6qdl_icore_nand_defconfig | 1 - 4 files changed, 1 insertion(+), 73 deletions(-)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig index 762a581..8456b0e 100644 --- a/arch/arm/cpu/armv7/mx6/Kconfig +++ b/arch/arm/cpu/armv7/mx6/Kconfig @@ -100,6 +100,7 @@ config TARGET_MX6Q_ICORE select MX6QDL select OF_CONTROL select DM + select DM_ETH select DM_GPIO select DM_MMC select DM_THERMAL diff --git a/board/engicam/icorem6/icorem6.c b/board/engicam/icorem6/icorem6.c index c152007..587775e 100644 --- a/board/engicam/icorem6/icorem6.c +++ b/board/engicam/icorem6/icorem6.c @@ -7,8 +7,6 @@ */
#include <common.h> -#include <miiphy.h> -#include <netdev.h>
#include <asm/io.h> #include <asm/gpio.h> @@ -27,80 +25,11 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ - PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - static iomux_v3_cfg_t const uart4_pads[] = { IOMUX_PADS(PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), };
-static iomux_v3_cfg_t const enet_pads[] = { - IOMUX_PADS(PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL | PAD_CTL_SRE_FAST)), - IOMUX_PADS(PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)), - IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL)), -}; - -#ifdef CONFIG_FEC_MXC -#define ENET_PHY_RST IMX_GPIO_NR(7, 12) -static int setup_fec(void) -{ - struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; - struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; - s32 timeout = 100000; - u32 reg = 0; - int ret; - - /* Enable fec clock */ - setbits_le32(&ccm->CCGR1, MXC_CCM_CCGR1_ENET_MASK); - - /* use 50MHz */ - ret = enable_fec_anatop_clock(0, ENET_50MHZ); - if (ret) - return ret; - - /* Enable PLLs */ - reg = readl(&anatop->pll_enet); - reg &= ~BM_ANADIG_PLL_SYS_POWERDOWN; - writel(reg, &anatop->pll_enet); - reg = readl(&anatop->pll_enet); - reg |= BM_ANADIG_PLL_SYS_ENABLE; - while (timeout--) { - if (readl(&anatop->pll_enet) & BM_ANADIG_PLL_SYS_LOCK) - break; - } - if (timeout <= 0) - return -EIO; - reg &= ~BM_ANADIG_PLL_SYS_BYPASS; - writel(reg, &anatop->pll_enet); - - /* reset the phy */ - gpio_direction_output(ENET_PHY_RST, 0); - udelay(10000); - gpio_set_value(ENET_PHY_RST, 1); - - return 0; -} - -int board_eth_init(bd_t *bis) -{ - int ret; - - SETUP_IOMUX_PADS(enet_pads); - setup_fec(); - - return ret = cpu_eth_init(bis); -} -#endif - #ifdef CONFIG_NAND_MXS
#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP) diff --git a/configs/imx6qdl_icore_mmc_defconfig b/configs/imx6qdl_icore_mmc_defconfig index b2d8cdf..a8199d5 100644 --- a/configs/imx6qdl_icore_mmc_defconfig +++ b/configs/imx6qdl_icore_mmc_defconfig @@ -28,7 +28,6 @@ CONFIG_CMD_FS_GENERIC=y CONFIG_OF_LIBFDT=y CONFIG_FEC_MXC=y CONFIG_MXC_UART=y -CONFIG_NETDEVICES=y CONFIG_IMX_THERMAL=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y diff --git a/configs/imx6qdl_icore_nand_defconfig b/configs/imx6qdl_icore_nand_defconfig index ca4ff0f..45f4808 100644 --- a/configs/imx6qdl_icore_nand_defconfig +++ b/configs/imx6qdl_icore_nand_defconfig @@ -24,7 +24,6 @@ CONFIG_OF_LIBFDT=y CONFIG_FEC_MXC=y CONFIG_MXC_UART=y CONFIG_NAND_MXS=y -CONFIG_NETDEVICES=y CONFIG_IMX_THERMAL=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y