This adds some registers needed for DUAL/QUAD/OCTAL modes. It also adds the fields in (R)ISR so we can check for over-/under-flow.
Signed-off-by: Sean Anderson seanga2@gmail.com ---
drivers/spi/designware_spi.c | 55 ++++++++++++++++++++++++++++++++++-- 1 file changed, 52 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/designware_spi.c b/drivers/spi/designware_spi.c index 1dd83e6ca6..169888a06d 100644 --- a/drivers/spi/designware_spi.c +++ b/drivers/spi/designware_spi.c @@ -56,6 +56,8 @@ #define DW_SPI_IDR 0x58 #define DW_SPI_VERSION 0x5c #define DW_SPI_DR 0x60 +#define DW_SPI_RX_SAMPLE_DLY 0xf0 +#define DW_SPI_SPI_CTRL0 0xf4
/* Bit fields in CTRLR0 */ /* @@ -80,8 +82,8 @@ #define CTRLR0_TMOD_RO 0x2 /* recv only */ #define CTRLR0_TMOD_EPROMREAD 0x3 /* eeprom read mode */
-#define CTRLR0_SLVOE_OFFSET 10 -#define CTRLR0_SRL_OFFSET 11 +#define CTRLR0_SLVOE_OFFSET BIT(10) +#define CTRLR0_SRL BIT(11) #define CTRLR0_CFS_MASK GENMASK(15, 12)
/* Only present when SSI_MAX_XFER_SIZE=32 */ @@ -92,13 +94,15 @@ #define CTRLR0_SPI_FRF_BYTE 0x0 #define CTRLR0_SPI_FRF_DUAL 0x1 #define CTRLR0_SPI_FRF_QUAD 0x2 +#define CTRLR0_SPI_FRF_OCTAL 0x3
/* Bit fields in CTRLR0 based on DWC_ssi_databook.pdf v1.01a */ #define DWC_SSI_CTRLR0_DFS_MASK GENMASK(4, 0) #define DWC_SSI_CTRLR0_FRF_MASK GENMASK(7, 6) #define DWC_SSI_CTRLR0_MODE_MASK GENMASK(9, 8) #define DWC_SSI_CTRLR0_TMOD_MASK GENMASK(11, 10) -#define DWC_SSI_CTRLR0_SRL_OFFSET 13 +#define DWC_SSI_CTRLR0_SRL BIT(13) +#define DWC_SSI_CTRLR0_SSTE BIT(14) #define DWC_SSI_CTRLR0_SPI_FRF_MASK GENMASK(23, 22)
/* Bit fields in SR, 7 bits */ @@ -111,6 +115,51 @@ #define SR_TX_ERR BIT(5) #define SR_DCOL BIT(6)
+/* Bit fields in (R)ISR */ + +/* TX FIFO Empty */ +#define ISR_TXEI BIT(0) +/* TX FIFO Overflow */ +#define ISR_TXOI BIT(1) +/* RX FIFO Underflow */ +#define ISR_RXUI BIT(2) +/* RX FIFO Overflow */ +#define ISR_RXOI BIT(3) +/* RX FIFO Full */ +#define ISR_RXFI BIT(4) +/* Multi-master contention */ +#define ISR_MSTI BIT(5) +/* XIP Receive FIFO Overflow */ +#define ISR_XRXOI BIT(6) +/* TX FIFO Underflow */ +#define ISR_TXUI BIT(7) +/* AXI Error */ +#define ISR_AXIE BIT(8) +/* SPI TX Error */ +#define ISR_SPITE BIT(10) +/* SSI Done */ +#define ISR_DONE BIT(11) + +/* Bit fields in SPI_CTRLR0 */ + +/* + * Whether the instruction or address use the value of SPI_FRF or use + * FRF_BYTE + */ +#define SPI_CTRLR0_TRANS_TYPE GENMASK(1, 0) +#define SPI_CTRLR0_TRANS_TYPE_1_1_X 0x0 +#define SPI_CTRLR0_TRANS_TYPE_1_X_X 0x1 +#define SPI_CTRLR0_TRANS_TYPE_X_X_X 0x2 +/* Address width in 4-bit units */ +#define SPI_CTRLR0_ADDR_L_MASK GENMASK(5, 2) +/* Enable mode bits after address in XIP mode */ +#define SPI_CTRLR0_XIP_MD_BIT_EN BIT(7) +/* Instruction width in 4-bit units */ +#define SPI_CTRLR0_INST_L_MASK GENMASK(9, 8) +/* Number of "dummy" cycles */ +#define SPI_CTRLR0_WAIT_CYCLES_MASK GENMASK(15, 11) +#define SPI_CTRLR0_CLK_STRETCH_EN BIT(30) + #define RX_TIMEOUT 1000 /* timeout in ms */
struct dw_spi_plat {