The mgcoge2 board from keymile deploys two different porcessors. An ARM based Kirkwood for the "unit" part of the SW and a PPC for the "ne" part of the SW. Therefore in Linux and U-Boot the names for the board are mgcoge2un and mgcoge2ne. This patch adds the mgcoge2ne part of the board. The ppc part of mgboge2 is quite similar to mgcoge, therefore a generic header km82xx-common.h was introduced to collect all similiarities. Currently the only difference is that mgcoge2ne has a 64 MB numonyx NOR flash with a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck holger.brunck@keymile.com Signed-off-by: Heiko Schocher hs@denx.de cc: Wolfgang Denk wd@denx.de cc: Valentin Longchamp valentin.longchamp@keymile.com --- MAINTAINERS | 1 + board/keymile/common/common.c | 4 +- board/keymile/mgcoge/mgcoge.c | 4 + boards.cfg | 1 + include/configs/km82xx-common.h | 321 +++++++++++++++++++++++++++++++++++++++ include/configs/mgcoge.h | 292 +----------------------------------- include/configs/mgcoge2ne.h | 63 ++++++++ 7 files changed, 395 insertions(+), 291 deletions(-) create mode 100644 include/configs/km82xx-common.h create mode 100644 include/configs/mgcoge2ne.h
diff --git a/MAINTAINERS b/MAINTAINERS index 9644d38..e4525e4 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -428,6 +428,7 @@ Heiko Schocher hs@denx.de jupiter MPC5200 kmeter1 MPC8360 mgcoge MPC8247 + mgcoge2ne MPC8247 mgcoge2un ARM926EJS (Kirkwood SoC) mucmc52 MPC5200 muas3001 MPC8270 diff --git a/board/keymile/common/common.c b/board/keymile/common/common.c index f0b99ed..f723cfa 100644 --- a/board/keymile/common/common.c +++ b/board/keymile/common/common.c @@ -22,7 +22,7 @@ */
#include <common.h> -#if defined(CONFIG_MGCOGE) +#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGCOGE2NE) #include <mpc8260.h> #endif #include <ioports.h> @@ -337,7 +337,7 @@ int ivm_read_eeprom (void) #define DELAY_ABORT_SEQ 62 #define DELAY_HALF_PERIOD (500 / (CONFIG_SYS_I2C_SPEED / 1000))
-#if defined(CONFIG_MGCOGE) +#if defined(CONFIG_MGCOGE) || defined(CONFIG_MGCOGE2NE) #define SDA_MASK 0x00010000 #define SCL_MASK 0x00020000 static void set_pin (int state, unsigned long mask) diff --git a/board/keymile/mgcoge/mgcoge.c b/board/keymile/mgcoge/mgcoge.c index 5c9496c..d9b0380 100644 --- a/board/keymile/mgcoge/mgcoge.c +++ b/board/keymile/mgcoge/mgcoge.c @@ -286,7 +286,11 @@ phys_size_t initdram (int board_type)
int checkboard(void) { +#if defined(CONFIG_MGCOGE) puts ("Board: Keymile mgcoge"); +#else + puts ("Board: Keymile mgcoge2ne"); +#endif if (ethernet_present ()) puts (" with PIGGY."); puts ("\n"); diff --git a/boards.cfg b/boards.cfg index 22cb509..3c45456 100644 --- a/boards.cfg +++ b/boards.cfg @@ -424,6 +424,7 @@ PQ2FADS-ZU_66MHz_lowboot powerpc mpc8260 mpc8260ads freesca PQ2FADS-ZU_lowboot powerpc mpc8260 mpc8260ads freescale - MPC8260ADS:ADSTYPE=CONFIG_SYS_PQ2FADS,SYS_TEXT_BASE=0xFF800000 VoVPN-GW_66MHz powerpc mpc8260 vovpn-gw funkwerk - VoVPN-GW:CLKIN_66MHz mgcoge powerpc mpc8260 - keymile +mgcoge2ne powerpc mpc8260 mgcoge keymile SCM powerpc mpc8260 - siemens TQM8255_AA powerpc mpc8260 tqm8260 tqc - TQM8260:MPC8255,300MHz TQM8260_AA powerpc mpc8260 tqm8260 tqc - TQM8260:MPC8260,200MHz diff --git a/include/configs/km82xx-common.h b/include/configs/km82xx-common.h new file mode 100644 index 0000000..b28cc99 --- /dev/null +++ b/include/configs/km82xx-common.h @@ -0,0 +1,321 @@ +/* + * (C) Copyright 2007-2010 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __KM82XX_COMMON +#define __KM82XX_COMMON + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +/* + * Select serial console configuration + * + * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + */ +#define CONFIG_CONS_ON_SMC /* Console is on SMC */ +#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ +#undef CONFIG_CONS_NONE /* It's not on external UART */ +#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */ +#define CONFIG_SYS_SMC_RXBUFLEN 128 +#define CONFIG_SYS_MAXIDLE 10 + +/* + * Select ethernet configuration + * + * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, + * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for + * SCC, 1-3 for FCC) + * + * If CONFIG_ETHER_NONE is defined, then either the ethernet routines + * must be defined elsewhere (as for the console), or CONFIG_CMD_NET + * must be unset. + */ +#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */ +#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */ +#undef CONFIG_ETHER_NONE /* No external Ethernet */ +#define CONFIG_NET_MULTI 1 + +#define CONFIG_ETHER_INDEX 4 +#define CONFIG_HAS_ETH0 +#define CONFIG_SYS_SCC_TOUT_LOOP 10000000 + +# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8) + +#ifndef CONFIG_8260_CLKIN +#define CONFIG_8260_CLKIN 66000000 /* in Hz */ +#endif + +#define BOOTFLASH_START 0xFE000000 + +#define CONFIG_KM_CONSOLE_TTY "ttyCPM0" + +#define MTDPARTS_DEFAULT "mtdparts=" \ + "app:" \ + "768k(u-boot)," \ + "128k(env)," \ + "128k(envred)," \ + "3072k(free)," \ + "-(" CONFIG_KM_UBI_PARTITION_NAME ")" + +/* + * Default environment settings + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ + "EEprom_ivm=pca9544a:70:4 \0" \ + "unlock=yes\0" \ + "newenv=" \ + "prot off 0xFE0C0000 +0x40000 && " \ + "era 0xFE0C0000 +0x40000\0" \ + "rootpath=/opt/eldk/ppc_82xx\0" \ + "" + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_LEN (768 << 10) /* Reserve 768KB for Monitor */ + +#define CONFIG_ENV_IS_IN_FLASH + +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) +#endif /* CONFIG_ENV_IS_IN_FLASH */ +#define CONFIG_ENV_BUFFER_PRINT 1 + +/* enable I2C and select the hardware/software driver */ +#undef CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * Software (bit-bang) I2C driver configuration + */ + +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) + +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +#define CONFIG_SYS_IMMR 0xF0000000 + +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* Hard reset configuration word */ +#define CONFIG_SYS_HRCW_MASTER 0x0604b211 + +/* No slaves */ +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 + +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) + +#define CONFIG_SYS_HID2 0 + +#define CONFIG_SYS_SIUMCR 0x4020c200 +#define CONFIG_SYS_SYPCR 0xFFFFFFC3 +#define CONFIG_SYS_BCR 0x10000000 +#define CONFIG_SYS_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK) + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CONFIG_SYS_RMR 0 + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RCCR 0 + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 8 bit FLASH + * 1 60x SDRAM 32 bit SDRAM + * 3 60x GPCM 8 bit GPIO/PIGGY + * 5 60x GPCM 16 bit CFG-Flash + * + */ +/* Bank 0 - FLASH + */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV2 |\ + ORxG_SCY_5_CLK |\ + ORxG_TRLX ) + + +/* Bank 1 - 60x bus SDRAM + */ +#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ +#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */ + +#define CONFIG_SYS_MPTPR 0x1800 + +/*----------------------------------------------------------------------------- + * Address for Mode Register Set (MRS) command + *----------------------------------------------------------------------------- + */ +#define CONFIG_SYS_MRS_OFFS 0x00000110 +#define CONFIG_SYS_PSRT 0x0e + +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1 + +/* SDRAM initialization values +*/ + +#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_8 |\ + ORxS_ROWST_PBI0_A7 |\ + ORxS_NUMR_13) + +#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A14_A16 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_5_CLK |\ + PSDMR_PRETOACT_2W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + +/* GPIO/PIGGY on CS3 initialization values +*/ +#define CONFIG_SYS_PIGGY_BASE 0x30000000 +#define CONFIG_SYS_PIGGY_SIZE 128 + +#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\ + BRx_PS_8 | BRx_MS_GPCM_P | BRx_V) + +#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\ + ORxG_CSNT | ORxG_ACS_DIV2 |\ + ORxG_SCY_3_CLK | ORxG_TRLX ) + +/* Board FPGA on CS4 initialization values +*/ +#define CONFIG_SYS_FPGA_BASE 0x40000000 +#define CONFIG_SYS_FPGA_SIZE 1 /*1KB*/ + +#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\ + BRx_PS_8 | BRx_MS_GPCM_P | BRx_V) + +#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\ + ORxG_CSNT | ORxG_ACS_DIV2 |\ + ORxG_SCY_3_CLK | ORxG_TRLX ) + +/* CFG-Flash on CS5 initialization values +*/ +#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\ + BRx_PS_16 | BRx_MS_GPCM_P | BRx_V) + +#define CONFIG_SYS_OR5_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \ + CONFIG_SYS_FLASH_SIZE_2) |\ + ORxG_CSNT | ORxG_ACS_DIV2 |\ + ORxG_SCY_5_CLK | ORxG_TRLX ) + +#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ + +/* pass open firmware flat tree */ +#define CONFIG_FIT 1 +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 + +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc/cpm/serial@11a90" + +#endif /* __KM82XX_COMMON */ diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h index 27f50a6..fbe8cdd 100644 --- a/include/configs/mgcoge.h +++ b/include/configs/mgcoge.h @@ -36,78 +36,10 @@
#define CONFIG_SYS_TEXT_BASE 0xFE000000
-#define CONFIG_CPM2 1 /* Has a CPM2 */ - /* include common defines/options for all Keymile boards */ #include "keymile-common.h" #include "km-powerpc.h"
-/* - * Select serial console configuration - * - * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - */ -#define CONFIG_CONS_ON_SMC /* Console is on SMC */ -#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ -#undef CONFIG_CONS_NONE /* It's not on external UART */ -#define CONFIG_CONS_INDEX 2 /* SMC2 is used for console */ -#define CONFIG_SYS_SMC_RXBUFLEN 128 -#define CONFIG_SYS_MAXIDLE 10 - -/* - * Select ethernet configuration - * - * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, - * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for - * SCC, 1-3 for FCC) - * - * If CONFIG_ETHER_NONE is defined, then either the ethernet routines - * must be defined elsewhere (as for the console), or CONFIG_CMD_NET - * must be unset. - */ -#define CONFIG_ETHER_ON_SCC /* Ethernet is on SCC */ -#undef CONFIG_ETHER_ON_FCC /* Ethernet is not on FCC */ -#undef CONFIG_ETHER_NONE /* No external Ethernet */ -#define CONFIG_NET_MULTI 1 - -#define CONFIG_ETHER_INDEX 4 -#define CONFIG_HAS_ETH0 -#define CONFIG_SYS_SCC_TOUT_LOOP 10000000 - -# define CONFIG_SYS_CMXSCR_VALUE (CMXSCR_RS4CS_CLK7 | CMXSCR_TS4CS_CLK8) - -#ifndef CONFIG_8260_CLKIN -#define CONFIG_8260_CLKIN 66000000 /* in Hz */ -#endif - -#define BOOTFLASH_START 0xFE000000 - -#define CONFIG_KM_CONSOLE_TTY "ttyCPM0" - -#define MTDIDS_DEFAULT "nor3=app" -#define MTDPARTS_DEFAULT "mtdparts=" \ - "app:" \ - "768k(u-boot)," \ - "128k(env)," \ - "128k(envred)," \ - "3072k(free)," \ - "-(" CONFIG_KM_UBI_PARTITION_NAME ")" - -/* - * Default environment settings - */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - CONFIG_KM_DEF_ENV \ - "EEprom_ivm=pca9544a:70:4 \0" \ - "unlock=yes\0" \ - "newenv=" \ - "prot off 0xFE0C0000 +0x40000 && " \ - "era 0xFE0C0000 +0x40000\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "" - #define CONFIG_SYS_SDRAM_BASE 0x00000000 #define CONFIG_SYS_FLASH_BASE 0xFE000000 #define CONFIG_SYS_FLASH_SIZE 32 @@ -125,227 +57,9 @@ CONFIG_SYS_FLASH_BASE_1, \ CONFIG_SYS_FLASH_BASE_2 }
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (768 << 10) /* Reserve 768KB for Monitor */ - -#define CONFIG_ENV_IS_IN_FLASH - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_OFFSET CONFIG_SYS_MONITOR_LEN - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ -#define CONFIG_ENV_BUFFER_PRINT 1 - -/* enable I2C and select the hardware/software driver */ -#undef CONFIG_HARD_I2C /* I2C with hardware support */ -#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * Software (bit-bang) I2C driver configuration - */ - -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ - -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) - -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 - -#define CONFIG_SYS_IMMR 0xF0000000 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Hard reset configuration word */ -#define CONFIG_SYS_HRCW_MASTER 0x0604b211 - -/* No slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) - -#define CONFIG_SYS_HID2 0 - -#define CONFIG_SYS_SIUMCR 0x4020c200 -#define CONFIG_SYS_SYPCR 0xFFFFFFC3 -#define CONFIG_SYS_BCR 0x10000000 -#define CONFIG_SYS_SCCR (SCCR_PCI_MODE | SCCR_PCI_MODCK) - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register 5-5 - *----------------------------------------------------------------------- - * turn on Checkstop Reset Enable - */ -#define CONFIG_SYS_RMR 0 - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 8 bit FLASH - * 1 60x SDRAM 32 bit SDRAM - * 3 60x GPCM 8 bit GPIO/PIGGY - * 5 60x GPCM 16 bit CFG-Flash - * - */ -/* Bank 0 - FLASH - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ - BRx_PS_8 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV2 |\ - ORxG_SCY_5_CLK |\ - ORxG_TRLX ) - - -/* Bank 1 - 60x bus SDRAM - */ -#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ -#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */ - -#define CONFIG_SYS_MPTPR 0x1800 - -/*----------------------------------------------------------------------------- - * Address for Mode Register Set (MRS) command - *----------------------------------------------------------------------------- - */ -#define CONFIG_SYS_MRS_OFFS 0x00000110 -#define CONFIG_SYS_PSRT 0x0e - -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1 - -/* SDRAM initialization values -*/ - -#define CONFIG_SYS_OR1 ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ - ORxS_BPD_8 |\ - ORxS_ROWST_PBI0_A7 |\ - ORxS_NUMR_13) - -#define CONFIG_SYS_PSDMR (PSDMR_SDAM_A14_IS_A5 |\ - PSDMR_BSMA_A14_A16 |\ - PSDMR_SDA10_PBI0_A9 |\ - PSDMR_RFRC_5_CLK |\ - PSDMR_PRETOACT_2W |\ - PSDMR_ACTTORW_2W |\ - PSDMR_LDOTOPRE_1C |\ - PSDMR_WRC_1C |\ - PSDMR_CL_2) - -/* GPIO/PIGGY on CS3 initialization values -*/ -#define CONFIG_SYS_PIGGY_BASE 0x30000000 -#define CONFIG_SYS_PIGGY_SIZE 128 - -#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIGGY_BASE & BRx_BA_MSK) |\ - BRx_PS_8 | BRx_MS_GPCM_P | BRx_V) - -#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) |\ - ORxG_CSNT | ORxG_ACS_DIV2 |\ - ORxG_SCY_3_CLK | ORxG_TRLX ) - -/* Board FPGA on CS4 initialization values -*/ -#define CONFIG_SYS_FPGA_BASE 0x40000000 -#define CONFIG_SYS_FPGA_SIZE 1 /*1KB*/ - -#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_FPGA_BASE & BRx_BA_MSK) |\ - BRx_PS_8 | BRx_MS_GPCM_P | BRx_V) - -#define CONFIG_SYS_OR4_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FPGA_SIZE << 10) |\ - ORxG_CSNT | ORxG_ACS_DIV2 |\ - ORxG_SCY_3_CLK | ORxG_TRLX ) - -/* CFG-Flash on CS5 initialization values -*/ -#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_FLASH_BASE_1 & BRx_BA_MSK) |\ - BRx_PS_16 | BRx_MS_GPCM_P | BRx_V) - -#define CONFIG_SYS_OR5_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE_1 + \ - CONFIG_SYS_FLASH_SIZE_2) |\ - ORxG_CSNT | ORxG_ACS_DIV2 |\ - ORxG_SCY_5_CLK | ORxG_TRLX ) - -#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ - -/* pass open firmware flat tree */ -#define CONFIG_FIT 1 -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 +#define MTDIDS_DEFAULT "nor3=app"
-#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc/cpm/serial@11a90" +/* include further common stuff for all keymile 82xx boards */ +#include "km82xx-common.h"
#endif /* __CONFIG_H */ diff --git a/include/configs/mgcoge2ne.h b/include/configs/mgcoge2ne.h new file mode 100644 index 0000000..d99d83e --- /dev/null +++ b/include/configs/mgcoge2ne.h @@ -0,0 +1,63 @@ +/* + * (C) Copyright 2007-2010 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __MGCOGE2NE +#define __MGCOGE2NE + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8247 1 +#define CONFIG_MPC8272_FAMILY 1 +#define CONFIG_MGCOGE 1 +#define CONFIG_HOSTNAME mgcoge2ne + +#define CONFIG_SYS_TEXT_BASE 0xFE000000 + +/* include common defines/options for all Keymile boards */ +#include "keymile-common.h" +#include "km-powerpc.h" + +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define CONFIG_SYS_FLASH_SIZE 32 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ + +#define CONFIG_SYS_FLASH_BASE_1 0x50000000 +#define CONFIG_SYS_FLASH_SIZE_1 64 +#define CONFIG_SYS_FLASH_SIZE_2 0 + +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, \ + CONFIG_SYS_FLASH_BASE_1 } + +#define MTDIDS_DEFAULT "nor2=app" + +/* include further common stuff for all keymile 82xx boards */ +#include "km82xx-common.h" + +#endif /* __MGCOGE2NE */