Hi Anand,
I have a odroid-xu4, but it doesn't detect the rtl8153:
U-Boot 2016.01-rc1-00441-g75507d5-dirty (Dec 07 2015 - 15:46:09 +0800) for ODROID-XU3
CPU: Exynos5422 @ 800 MHz Model: Odroid XU3 based on EXYNOS5422 Board: Odroid XU3 based on EXYNOS5422 Type: xu4 DRAM: 2 GiB __of_translate_address: Bad cell count for gpx0 MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... starting USB... USB0: USB EHCI 1.00 USB1: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.00 USB2: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 2 USB Device(s) found scanning bus 2 for devices... 2 USB Device(s) found scanning usb for ethernet devices... Setup ERROR: address device command for slot 1. Unknown version 0x0000 Unknown Device 0 Ethernet Device(s) found No ethernet found.
could you send me your odroid-xu3_defconfig? Thanks. BTW, I added "#define CONFIG_USB_ETHER_RTL8152" to include/configs/exynos5-common.h
Regards, Joe
On Wed, Nov 25, 2015 at 5:09 PM, Anand Moon linux.amoon@gmail.com wrote:
Hi Ted,
On 25 November 2015 at 11:27, Ted Chen tedchen@realtek.com wrote:
Add a condition of set_address and set_configuration to check if the request is standardized.
Signed-off-by: Ted Chen tedchen@realtek.com
drivers/usb/host/xhci.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index ca598aa..cb8a04b 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -941,10 +941,12 @@ static int _xhci_submit_control_msg(struct
usb_device *udev, unsigned long pipe,
if (usb_pipedevice(pipe) == ctrl->rootdev) return xhci_submit_root(udev, pipe, buffer, setup);
if (setup->request == USB_REQ_SET_ADDRESS)
if (setup->request == USB_REQ_SET_ADDRESS &&(setup->requesttype & USB_TYPE_MASK) == USB_TYPE_STANDARD) return xhci_address_device(udev, root_portnr);
if (setup->request == USB_REQ_SET_CONFIGURATION) {
if (setup->request == USB_REQ_SET_CONFIGURATION &&(setup->requesttype & USB_TYPE_MASK) == USB_TYPE_STANDARD) { ret = xhci_set_configuration(udev); if (ret) { puts("Failed to configure xHCI endpoint\n");-- 1.7.9.5
Tested on Odroid-XU4 with Ethernet USB3.0 RT8153-VB.
Tested-by: Anand Moon linux.amoon@gmail.com Reviewed-by: Anand Moon linux.amoon@gmail.com
-Anand Moon _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot