From: Sjoerd Simons sjoerd@collabora.com
Add glue code for TI AM62 to the dwc3 driver; Most code adopted from TI vendor u-boot code.
Signed-off-by: Sjoerd Simons sjoerd@collabora.com Tested-by: Alexander Sverdlin alexander.sverdlin@siemens.com Reviewed-by: Mattijs Korpershoek mkorpershoek@baylibre.com Tested-by: Mattijs Korpershoek mkorpershoek@baylibre.com # on beagle play --- Changes in v5: - No change
Changes in v4: - Add config dependency on SYSCON - Move defines and constants outside out of function scope
Changes in v2: - Switch dwc3 glue to a seperate driver rather then in dwc-generic
drivers/usb/dwc3/Kconfig | 14 ++++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-am62.c | 125 +++++++++++++++++++++++++++++++++++ 3 files changed, 140 insertions(+) create mode 100644 drivers/usb/dwc3/dwc3-am62.c
diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig index c0c8c16fd9..0100723a68 100644 --- a/drivers/usb/dwc3/Kconfig +++ b/drivers/usb/dwc3/Kconfig @@ -37,6 +37,20 @@ config SPL_USB_DWC3_GENERIC Select this for Xilinx ZynqMP and similar Platforms. This wrapper supports Host and Peripheral operation modes.
+config SPL_USB_DWC3_AM62 + bool "TI AM62 USB wrapper" + depends on SPL_DM_USB && SPL_USB_DWC3_GENERIC && SPL_SYSCON + help + Select this for TI AM62 Platforms. + This wrapper supports Host and Peripheral operation modes. + +config USB_DWC3_AM62 + bool "TI AM62 USB wrapper" + depends on DM_USB && USB_DWC3_GENERIC && SYSCON + help + Select this for TI AM62 Platforms. + This wrapper supports Host and Peripheral operation modes. + config USB_DWC3_MESON_G12A bool "Amlogic Meson G12A USB wrapper" depends on DM_USB && USB_DWC3 && ARCH_MESON diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile index 97b4f7191c..a46b6824ab 100644 --- a/drivers/usb/dwc3/Makefile +++ b/drivers/usb/dwc3/Makefile @@ -6,6 +6,7 @@ dwc3-y := core.o
obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o
+obj-$(CONFIG_$(SPL_)USB_DWC3_AM62) += dwc3-am62.o obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o obj-$(CONFIG_USB_DWC3_MESON_GXL) += dwc3-meson-gxl.o diff --git a/drivers/usb/dwc3/dwc3-am62.c b/drivers/usb/dwc3/dwc3-am62.c new file mode 100644 index 0000000000..99519602eb --- /dev/null +++ b/drivers/usb/dwc3/dwc3-am62.c @@ -0,0 +1,125 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * TI AM62 specific glue layer for DWC3 + */ + +#include <dm.h> +#include <dm/device_compat.h> +#include <regmap.h> +#include <syscon.h> +#include <asm/io.h> + +#include "dwc3-generic.h" + +#define USBSS_MODE_CONTROL 0x1c +#define USBSS_PHY_CONFIG 0x8 +#define USBSS_PHY_VBUS_SEL_MASK GENMASK(2, 1) +#define USBSS_PHY_VBUS_SEL_SHIFT 1 +#define USBSS_MODE_VALID BIT(0) +#define PHY_PLL_REFCLK_MASK GENMASK(3, 0) +static const int dwc3_ti_am62_rate_table[] = { /* in KHZ */ + 9600, + 10000, + 12000, + 19200, + 20000, + 24000, + 25000, + 26000, + 38400, + 40000, + 58000, + 50000, + 52000, +}; + +static void dwc3_ti_am62_glue_configure(struct udevice *dev, int index, + enum usb_dr_mode mode) +{ + struct clk usb2_refclk; + int rate_code, i, ret; + unsigned long rate; + u32 reg; + void *usbss; + bool vbus_divider; + struct regmap *syscon; + struct ofnode_phandle_args args; + + usbss = dev_remap_addr_index(dev, 0); + if (IS_ERR(usbss)) { + dev_err(dev, "can't map IOMEM resource\n"); + return; + } + + ret = clk_get_by_name(dev, "ref", &usb2_refclk); + if (ret) { + dev_err(dev, "can't get usb2_refclk\n"); + return; + } + + /* Calculate the rate code */ + rate = clk_get_rate(&usb2_refclk); + rate /= 1000; /* To KHz */ + for (i = 0; i < ARRAY_SIZE(dwc3_ti_am62_rate_table); i++) { + if (dwc3_ti_am62_rate_table[i] == rate) + break; + } + + if (i == ARRAY_SIZE(dwc3_ti_am62_rate_table)) { + dev_err(dev, "unsupported usb2_refclk rate: %lu KHz\n", rate); + return; + } + + rate_code = i; + + /* Read the syscon property */ + syscon = syscon_regmap_lookup_by_phandle(dev, "ti,syscon-phy-pll-refclk"); + if (IS_ERR(syscon)) { + dev_err(dev, "unable to get ti,syscon-phy-pll-refclk regmap\n"); + return; + } + + ret = ofnode_parse_phandle_with_args(dev_ofnode(dev), "ti,syscon-phy-pll-refclk", NULL, 1, + 0, &args); + if (ret) + return; + + /* Program PHY PLL refclk by reading syscon property */ + ret = regmap_update_bits(syscon, args.args[0], PHY_PLL_REFCLK_MASK, rate_code); + if (ret) { + dev_err(dev, "failed to set phy pll reference clock rate\n"); + return; + } + + /* VBUS divider select */ + reg = readl(usbss + USBSS_PHY_CONFIG); + vbus_divider = dev_read_bool(dev, "ti,vbus-divider"); + if (vbus_divider) + reg |= 1 << USBSS_PHY_VBUS_SEL_SHIFT; + + writel(reg, usbss + USBSS_PHY_CONFIG); + + /* Set mode valid */ + reg = readl(usbss + USBSS_MODE_CONTROL); + reg |= USBSS_MODE_VALID; + writel(reg, usbss + USBSS_MODE_CONTROL); +} + +struct dwc3_glue_ops ti_am62_ops = { + .glue_configure = dwc3_ti_am62_glue_configure, +}; + +static const struct udevice_id dwc3_am62_match[] = { + { .compatible = "ti,am62-usb", .data = (ulong)&ti_am62_ops }, + { /* sentinel */ } +}; + +U_BOOT_DRIVER(dwc3_am62_wrapper) = { + .name = "dwc3-am62", + .id = UCLASS_SIMPLE_BUS, + .of_match = dwc3_am62_match, + .bind = dwc3_glue_bind, + .probe = dwc3_glue_probe, + .remove = dwc3_glue_remove, + .plat_auto = sizeof(struct dwc3_glue_data), +};