Add LCD definitions and also a proposed binding for LCD displays.
The PWFM is in progress on the device-tree-discuss list, so only a very basic binding is offered here.
Signed-off-by: Simon Glass sjg@chromium.org --- arch/arm/dts/tegra20.dtsi | 25 ++++++ doc/device-tree-bindings/video/nvidia-video.txt | 92 +++++++++++++++++++++++ 2 files changed, 117 insertions(+), 0 deletions(-) create mode 100644 doc/device-tree-bindings/video/nvidia-video.txt
diff --git a/arch/arm/dts/tegra20.dtsi b/arch/arm/dts/tegra20.dtsi index 3d435aa..85c8bf6 100644 --- a/arch/arm/dts/tegra20.dtsi +++ b/arch/arm/dts/tegra20.dtsi @@ -221,4 +221,29 @@ compatible = "nvidia,tegra20-kbc"; reg = <0x7000e200 0x0078>; }; + + pwfm0: pwm@7000a000 { + compatible = "nvidia,tegra20-pwfm"; + reg = <0x7000a000 0x4>; + }; + + pwfm1: pwm@7000a010 { + compatible = "nvidia,tegra20-pwfm"; + reg = <0x7000a010 0x4>; + }; + + pwfm2: pwm@7000a020 { + compatible = "nvidia,tegra20-pwfm"; + reg = <0x7000a020 0x4>; + }; + + pwfm3: pwm@7000a030 { + compatible = "nvidia,tegra20-pwfm"; + reg = <0x7000a030 0x4>; + }; + + display1: display@0x54200000 { + compatible = "nvidia,tegra20-display"; + reg = <0x54200000 0x40000>; + }; }; diff --git a/doc/device-tree-bindings/video/nvidia-video.txt b/doc/device-tree-bindings/video/nvidia-video.txt new file mode 100644 index 0000000..ede9260 --- /dev/null +++ b/doc/device-tree-bindings/video/nvidia-video.txt @@ -0,0 +1,92 @@ +LCD Display +----------- + +(there isn't yet a generic binding in Linux, so this describes what is in +U-Boot) + +The device node for a display device is as described in the document +"Open Firmware Recommended Practice : Universal Serial Bus" with the +following modifications and additions : + +Required properties : + - compatible : Should be "nvidia,tegra20-display" + - pwfm: phandle of PWFM to use for backlight + +Note: This is just a phande and provides no information, nor a backlight +node. The PWM is still under discussion I think: + http://patchwork.ozlabs.org/patch/132386/ + +We don't support any parameters as yet - the setting is hard-coded. + + - width: width of display in pixels + - height: height of display in pixels + - bits-per-pixel: number of bits per pixel (depth) + - pixel-clock : Pixel clock in Hz + - horiz-timing; horizontal timing: ref_to_sync, sync_width. back_porch, + front_porch + - vert-timing; vertical timing: ref_to_sync, sync_width. back_porch, + front_porch + +This node should sit inside its controller. + + +Nvidia Tegra2x Display Controller +--------------------------------- + +The device node for a NAND flash controller is as described in the document +"Open Firmware Recommended Practice : Universal Serial Bus" with the +following modifications and additions : + +Required properties: + - compatible: should be "tegra20-display" + - panel-timings: 4 cells containing required timings in ms: + * delay between panel_vdd-rise and data-rise + * delay between data-rise and backlight_vdd-rise + * delay between backlight_vdd and pwm-rise + * delay between pwm-rise and backlight_en-rise + +(should we use us here, or perhaps call it panel-timings-ms?) + +Optional properties: + - frame-buffer: address of frame buffer (if omitted it will be calculated) + - This may be useful to share an address between U-Boot and Linux and + avoid boot-time corruption / flicker + +Optional GPIO properies all have (phandle, GPIO number, flags): + - backlight-enable-gpio: backlight enable GPIO + - lvds-shutdown-gpio: LVDS power shutdown GPIO + - backlight-vdd-gpio: backlight power GPIO + - panel-vdd-gpio: panel power GPIO + +(should those have an "nvidia," prefix? Perhap use polariy bit so that +lvds-shutdown becomes lvds-enable?) + +I have put these into the display controller since I don't think they are +generic enough to go in the lcd node. + +Example: + +display@0x54200000 { + pwfm = <&pwfm2>; + + /* frame-buffer location to share with Linux */ + frame-buffer = <0x2f680000>; + + /* Parameter 3 bit 0:1=output, 0=input; bit 1:1=high, 0=low */ + backlight-enable = <&gpio 28 0>; /* PD4 */ + lvds-shutdown = <&gpio 10 0>; /* PB2 */ + backlight-vdd = <&gpio 176 0>; /* PW0 */ + panel-vdd = <&gpio 22 0>; /* PC6 */ + panel-timings = <4 203 17 15>; + + lcd { + compatible = "generic,lcd"; + width = <1366>; + height = <768>; + bits-per-pixel = <16>; + pixel-clock = <70600000>; + + horiz-timing = <11 58 58 58>; + vert-timing = <1 4 4 4>; + }; +};