Hi Kuldeep,
On 11.12.19 13:23, Kuldeep Singh wrote:
Hi Frieder,
[...]
> Patch 2 adds new qspi driver incorporating spi-mem framework which > is ported version of linux qspi driver. Initial port was done by Frieder. > Now, no more direct access to spi-nor memory is possible. Few > changes were introduced to prevent uboot crash such as to add > complete flash size to SFA1AD, SFA2AD, SFB1AD, SFB2AD based on > chip select number instead of 1k. Immediate effect was observed on > pfe while using 1k size as it access spi-nor memory directly. > Using complete flash size resolves the crash but data read will not be valid.
Can you provide more information about the problem/crash you experience and the platform you are working on?
I observed crash on LS1012. Also, any access to flash direct memory above
1k will crash without this change.
As I already told Ashish in the conversation referenced in my last mail: I can't see any good reason why the direct memory access is something that we need or should support. We should always use the APIs provided by U-Boot to access the flash and that is mtd.
By adding this, crash will be resolved but data is invalid as mentioned in
patch-set.
So what's the purpose of your changes at all, if they do not solve the problem you're trying to solve?
I observed booting crash on all ls1012 platforms. Control does not reach
even end of uboot prompt.
I dig in deeper, and found that "pfe (packet forwarding engine)" was using
spi-nor memory directly.
With this change, booting crash was resolved. Now, at least other network
interfaces can be used.
Without this changes, I have to disable pfe on adhoc basis so as to get uboot
prompt.
This is to make sure all intended qspi targets are booting.
Ok, thanks for pointing out the PFE driver. I didn't know about such a peripheral. So this seems to be the actual problem here.
I don't really understand, why Ashish didn't mention this when we were talking about this issue some weeks ago.
Why don't you just use sf/mtd to access the flash?
Pfe framework have to bring in changes to access flash using sf in uboot.
Yes and that's something that should be done first instead of hacking the QSPI controller driver. It shouldn't be too hard to modify the PFE driver so that it uses the serial flash API (spi_flash_read()) to access the SPI NOR. Can you try to come up with a patch for the PFE driver?
I have sent out PFE driver patch upstream[1] and booting crash is now resolved.
Ok, good.
Moreover, After using 1k size, I faced a random crash in environment which was resolved after enabling SYS_RELOC_GD_ENV_ADDR in defconfig. I am not sure why this needed when setting 1k size? Note that, same is not required if I use my previous implementation.
SYS_RELOC_GD_ENV_ADDR was only introduced very recently and it seems like it should be enabled for your boards (see [1]) when using something more recent than 8d8ee47e03ef.
My guess would be that you're missing the "CONFIG_SYS_RELOC_GD_ENV_ADDR=y" because of some mistake while rebasing or merging .
Now, I found a new bug while testing read functionality in LS1012A, LS1046A on commit "4b19b89ca4a8". I cannot access memory above 16MB. For example, when I try to access 16M, data read is actually from 0x0 offset. Could you please share your views on this behavior.
This is usually a problem if the addressing mode for the SPI NOR is incorrect. When using 2-bytes addresses, only the first 16MiB of the flash can be accessed. For SPI NOR flashes with sizes bigger than 16MiB, 3-byte mode is mandatory to access areas above 16MiB.
What's the manufacturer and type of the SPI flash you are using? Also please try to test on latest master with all the latest changes for MTD, etc.
Thanks, Frieder
[1] https://gitlab.denx.de/u-boot/u-boot/commit/8d8ee47e03ef23b0d0e842ea455a30bf...
--Kuldeep
Thanks Kuldeep
Are you referring to the same issue as Ashish in this discussion here [1]?
Yes, I had a discussion with him.
There are two reasons why I'd like to avoid using the whole memory mapped area for AHB access. First, I'd like to keep the U-Boot driver as close as possible to the Linux
driver.
Second, the intention of the spi-mem layer is to abstract the flash layer and therefore this driver should work independently of flash type or
size.
Boot from QSPI-NAND will still not be possible. Code in bootROM is only to
access QSPI-NOR.
It will not be possible to use SPI NAND directly from the BootROM, but you can just load the bootloader from a different device like SPI NOR and then fetch the rest of the system (Kernel, rootfs, etc.) from a SPI NAND device. Actually that's exactly the use case, that led to the development of the SPI MEM layer and the migration of the QSPI driver.
With your version this wouldn't be the case if you connect a flash that is bigger than the memory map for example.
I agree such use case can be valid for Linux but in case of Uboot, I believe
access to flash size greater than 256M will not be required.
If in case there is a requirement, there is another region in CCSR space to
map flash memories up to 4G.
Random crashes can be avoided by adding these changes. Please let us know
your views as well.
We don't even need to consider these cases, if we would just stick to the SPI MEM API and use it as intended. Apart from some possible performance penalty (that shouldn't matter too much and could be resolved by implementing the direct mapping API as in Linux), I can't see the reason for not doing so.