From: Amit Singh Tomar amittomer25@gmail.com
This series(v3) addresses review comments provided by Andre and Jaehoon. Earlier in MMC driver, we were *not* checking the command response errors(for instance, the CRC error) based on STATU register. This is now addressed in patch 5/6.
Also, MMC driver(pacth 5/6) now has replaced the switch/case with if/else to correlate MMC_RSP_Rx bitmask values with register bits as suggested by Andre.
Apart from it, there are changes in patch 2/6 to fix weird assignments to div variable.
---------------------------------------------------------------------------------- Series(v2) has few important updates, while loading large files we found that MMC framework puts "0x1fffe00" into DMA Frame Length(DMA_FRAME_LEN 0x000C) but register itself is limited to 24 bits and hence it was failing. It is due to the wrong Block count(cfg->b_max) used in driver, that should be just 512. This is now fixed in patch 5/6.
Apart from it, as Andre pointed that we might be just overclocking the MMC/SD clock, and to confirm this we run following test:
$ md5sum clang 349eac46cbbe28f8e44da2dce07fa7b7 clang
U-Boot => ext4load mmc 0:2 0x0 clang 503316480 bytes read in 19516 ms (24.6 MiB/s) U-Boot => md5sum 0x0 0x1e000000 md5 for 00000000 ... 1dffffff ==> d793bb51c4a1cf83c96d1980927461ff
Even though file gets loaded but md5sum doesn't match. This is now fixed in patch 2/6
U-Boot => ext4load mmc 0:2 0x0 clang 503316480 bytes read in 41524 ms (11.6 MiB/s) U-Boot => md5sum 0x0 0x1e000000 md5 for 00000000 ... 1dffffff ==> 349eac46cbbe28f8e44da2dce07fa7b7
----------------------------------------------------------------------------- At the moment on S700 based platforms, only way to load/boot the Kernel is from Ethernet, and with these patches one can now load/boot the Kernel from uSD card.
Patches(1/6 and 2/6) adds changes needed for MMC/SD clock. It introduces set/get callback routine and get/set MMC/SD clock rate based on device id.
Patch 4/6 adds MMC/SD node in U-boot specific dtsi file, which is used by MMC/SD driver to read controller base address later on.
Patch 5/6 adds driver for MMC/SD controller present on S700 SoC, and its based on Mainline Linux driver and DMA related bits is picked and simpilified from vendor source.
Final patch 6/6 enables the driver support along with MMC commands in Cubieboard7 config file.
Also, while at it just took the opportunity to synchronize the S700 SoC DT with Linux in patch 3/6.
This patch-set is tested on Cubieboard7-lite board with following results:
U-Boot 2021.01-rc1-04434-g6589149-dirty (Dec 13 2020 - 13:51:07 +0530) cubieboard7
DRAM: 1 GiB PSCI: v0.2 MMC: mmc@e0210000: 0 In: serial@e0126000 Out: serial@e0126000 Err: serial@e0126000 Net: eth0: ethernet@e0220000 Hit any key to stop autoboot: 0 U-Boot => U-Boot => U-Boot => U-Boot => mmc info Device: mmc@e0210000 Manufacturer ID: 3 OEM: 5344 Name: SC16G Bus Speed: 50000000 Mode: SD High Speed (50MHz) Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 14.8 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes U-Boot => setenv bootargs console=ttyOWL3,115200n8 earlycon=owl,0xe0126000 init=/sbin/init root=/dev/mmcblk0p2 rw rootwait U-Boot => setenv kernel_addr_r 0x80000;setenv fdt_addr_r 0x10000000; U-Boot => fatload mmc 0:1 ${kernel_addr_r} image ;fatload mmc 0:1 ${fdt_addr_r} s700-cubieboard7.dtb 27480576 bytes read in 1041 ms (25.2 MiB/s) 7056 bytes read in 2 ms (3.4 MiB/s) U-Boot => booti $kernel_addr_r - $fdt_addr_r ## Flattened Device Tree blob at 10000000 Booting using the fdt blob at 0x10000000 Loading Device Tree to 000000003df56000, end 000000003df5ab8f ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.7.0-rc6-00022-g99f1c330923b-dirty (amit@amit-ThinkPad-X230) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05), GNU ld (GNU Binutils for Ubuntu) 2.26.1) #474 SMP PREEMPT Thu Aug 13 15:27:10 IST 2020 [ 0.000000] Machine model: CubieBoard7 [ 0.000000] earlycon: owl0 at MMIO 0x00000000e0126000 (options '') [ 0.000000] printk: bootconsole [owl0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x000000003e000000
Amit Singh Tomar (6): clk: actions: Introduce dummy get/set_rate callbacks clk: actions: Add SD/MMC clocks ARM: dts: sync Actions Semi S700 DT from Linux 5.10-rc7 ARM: dts: s700: add MMC/SD controller node mmc: actions: add MMC driver for Actions OWL S700/S900 configs: Enable mmc support
arch/arm/dts/s700-u-boot.dtsi | 10 + arch/arm/dts/s700.dtsi | 17 +- configs/cubieboard7_defconfig | 3 + drivers/clk/owl/clk_owl.c | 99 ++++++ drivers/mmc/Kconfig | 7 + drivers/mmc/Makefile | 1 + drivers/mmc/owl_mmc.c | 401 +++++++++++++++++++++++++ include/dt-bindings/power/owl-s700-powergate.h | 19 ++ 8 files changed, 556 insertions(+), 1 deletion(-) create mode 100644 drivers/mmc/owl_mmc.c create mode 100644 include/dt-bindings/power/owl-s700-powergate.h