The Bananapi M3 has an RTL8211E PHY connected to the EMAC using RGMII. The PHY is powered by DCDC1 through SW @ 3.3V.
This patch adds a U-boot specific dtsi file for the board adding an enabled EMAC node, and enables the EMAC driver in the defconfig. The binding used here is the old revision currently supported in U-boot. There is no stable binding nor support in upstream Linux at this time.
Signed-off-by: Chen-Yu Tsai wens@csie.org --- arch/arm/dts/sun8i-a83t-bananapi-m3-u-boot.dtsi | 41 +++++++++++++++++++++++++ configs/Sinovoip_BPI_M3_defconfig | 1 + 2 files changed, 42 insertions(+) create mode 100644 arch/arm/dts/sun8i-a83t-bananapi-m3-u-boot.dtsi
diff --git a/arch/arm/dts/sun8i-a83t-bananapi-m3-u-boot.dtsi b/arch/arm/dts/sun8i-a83t-bananapi-m3-u-boot.dtsi new file mode 100644 index 000000000000..9c7977e67b92 --- /dev/null +++ b/arch/arm/dts/sun8i-a83t-bananapi-m3-u-boot.dtsi @@ -0,0 +1,41 @@ +#include "sunxi-u-boot.dtsi" + +/ { + aliases { + ethernet0 = &emac; + }; + + soc { + emac: ethernet@01c30000 { + compatible = "allwinner,sun8i-a83t-emac"; + reg = <0x01c30000 0x2000>, <0x01c00030 0x4>; + reg-names = "emac", "syscon"; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii"; + phy = <&phy1>; + allwinner,rx-delay-ps = <700>; + allwinner,tx-delay-ps = <700>; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; +}; + +&pio { + rgmii_pins: rgmii_pins { + allwinner,pins = "PD8", "PD9", "PD10", "PD11", + "PD12", "PD13", "PD15", + "PD16", "PD17", "PD18", "PD19", + "PD20", "PD21", "PD22", "PD23"; + allwinner,function = "emac"; + allwinner,drive = <3>; + allwinner,pull = <0>; + }; +}; diff --git a/configs/Sinovoip_BPI_M3_defconfig b/configs/Sinovoip_BPI_M3_defconfig index e48983fc3310..efdf3c7396fd 100644 --- a/configs/Sinovoip_BPI_M3_defconfig +++ b/configs/Sinovoip_BPI_M3_defconfig @@ -23,6 +23,7 @@ CONFIG_SPL=y # CONFIG_SPL_DOS_PARTITION is not set # CONFIG_SPL_ISO_PARTITION is not set # CONFIG_SPL_EFI_PARTITION is not set +CONFIG_SUN8I_EMAC=y CONFIG_AXP_DCDC5_VOLT=1200 CONFIG_AXP_DLDO3_VOLT=2500 CONFIG_AXP_SW_ON=y