We rework the various board_is_foo() checks to take a pointer to struct am335x_baseboard_id rather than using a local copy in board.c. This allows us to make use of the same checks in mux.c as well as fixing problems when this code could be running from read-only memory.
Signed-off-by: Tom Rini trini@ti.com --- board/ti/am335x/board.c | 78 ++++++++++++++++------------------------------- board/ti/am335x/board.h | 31 +++++++++++++++++++ board/ti/am335x/mux.c | 10 +++--- 3 files changed, 62 insertions(+), 57 deletions(-)
diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index b371376..6f6b5d0 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -51,43 +51,10 @@ static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-static struct am335x_baseboard_id __attribute__((section (".data"))) header; - -static inline int board_is_bone(void) -{ - return !strncmp(header.name, "A335BONE", HDR_NAME_LEN); -} - -static inline int board_is_bone_lt(void) -{ - return !strncmp(header.name, "A335BNLT", HDR_NAME_LEN); -} - -static inline int board_is_evm_sk(void) -{ - return !strncmp("A335X_SK", header.name, HDR_NAME_LEN); -} - -static inline int board_is_idk(void) -{ - return !strncmp(header.config, "SKU#02", 6); -} - -static int __maybe_unused board_is_gp_evm(void) -{ - return !strncmp("A33515BB", header.name, 8); -} - -int board_is_evm_15_or_later(void) -{ - return (!strncmp("A33515BB", header.name, 8) && - strncmp("1.5", header.version, 3) <= 0); -} - /* * Read header information from EEPROM into global structure. */ -static int read_eeprom(void) +static int read_eeprom(struct am335x_baseboard_id *header) { /* Check if baseboard eeprom is available */ if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) { @@ -97,28 +64,28 @@ static int read_eeprom(void) }
/* read the eeprom using i2c */ - if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)&header, - sizeof(header))) { + if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header, + sizeof(struct am335x_baseboard_id))) { puts("Could not read the EEPROM; something fundamentally" " wrong on the I2C bus.\n"); return -EIO; }
- if (header.magic != 0xEE3355AA) { + if (header->magic != 0xEE3355AA) { /* * read the eeprom using i2c again, * but use only a 1 byte address */ - if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, - (uchar *)&header, sizeof(header))) { + if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header, + sizeof(struct am335x_baseboard_id))) { puts("Could not read the EEPROM; something " "fundamentally wrong on the I2C bus.\n"); return -EIO; }
- if (header.magic != 0xEE3355AA) { + if (header->magic != 0xEE3355AA) { printf("Incorrect magic number (0x%x) in EEPROM\n", - header.magic); + header->magic); return -EINVAL; } } @@ -304,6 +271,8 @@ static struct emif_regs ddr3_evm_emif_reg_data = { */ void s_init(void) { + __maybe_unused struct am335x_baseboard_id header; + /* WDT1 is already running when the bootloader gets control * Disable it to avoid "random" resets */ @@ -362,11 +331,11 @@ void s_init(void) /* Initalize the board header */ enable_i2c0_pin_mux(); i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - if (read_eeprom() < 0) + if (read_eeprom(&header) < 0) puts("Could not get board ID.\n");
enable_board_pin_mux(&header); - if (board_is_evm_sk()) { + if (board_is_evm_sk(&header)) { /* * EVM SK 1.2A and later use gpio0_7 to enable DDR3. * This is safe enough to do on older revs. @@ -375,15 +344,15 @@ void s_init(void) gpio_direction_output(GPIO_DDR_VTT_EN, 1); }
- if (board_is_evm_sk()) + if (board_is_evm_sk(&header)) config_ddr(303, MT41J128MJT125_IOCTRL_VALUE, &ddr3_data, &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0); - else if (board_is_bone_lt()) + else if (board_is_bone_lt(&header)) config_ddr(400, MT41K256M16HA125E_IOCTRL_VALUE, &ddr3_beagleblack_data, &ddr3_beagleblack_cmd_ctrl_data, &ddr3_beagleblack_emif_reg_data, 0); - else if (board_is_evm_15_or_later()) + else if (board_is_evm_15_or_later(&header)) config_ddr(303, MT41J512M8RH125_IOCTRL_VALUE, &ddr3_evm_data, &ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0); else @@ -397,10 +366,6 @@ void s_init(void) */ int board_init(void) { - i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); - if (read_eeprom() < 0) - puts("Could not get board ID.\n"); - gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
gpmc_init(); @@ -413,6 +378,10 @@ int board_late_init(void) { #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG char safe_string[HDR_NAME_LEN + 1]; + struct am335x_baseboard_id header; + + if (read_eeprom(&header) < 0) + puts("Could not get board ID.\n");
/* Now set variables based on the header. */ strncpy(safe_string, (char *)header.name, sizeof(header.name)); @@ -476,6 +445,7 @@ int board_eth_init(bd_t *bis) int rv, n = 0; uint8_t mac_addr[6]; uint32_t mac_hi, mac_lo; + __maybe_unused struct am335x_baseboard_id header;
/* try reading mac address from efuse */ mac_lo = readl(&cdev->macid0l); @@ -496,7 +466,11 @@ int board_eth_init(bd_t *bis) eth_setenv_enetaddr("ethaddr", mac_addr); }
- if (board_is_bone() || board_is_bone_lt() || board_is_idk()) { + if (read_eeprom(&header) < 0) + puts("Could not get board ID.\n"); + + if (board_is_bone(&header) || board_is_bone_lt(&header) || + board_is_idk(&header)) { writel(MII_MODE_ENABLE, &cdev->miisel); cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_MII; @@ -524,7 +498,7 @@ int board_eth_init(bd_t *bis) #define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5 #define AR8051_RGMII_TX_CLK_DLY 0x100
- if (board_is_evm_sk() || board_is_gp_evm()) { + if (board_is_evm_sk(&header) || board_is_gp_evm(&header)) { const char *devname; devname = miiphy_get_current_dev();
diff --git a/board/ti/am335x/board.h b/board/ti/am335x/board.h index 48e112e..36ccaec 100644 --- a/board/ti/am335x/board.h +++ b/board/ti/am335x/board.h @@ -37,6 +37,37 @@ struct am335x_baseboard_id { char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN]; };
+static inline int board_is_bone(struct am335x_baseboard_id *header) +{ + return !strncmp(header->name, "A335BONE", HDR_NAME_LEN); +} + +static inline int board_is_bone_lt(struct am335x_baseboard_id *header) +{ + return !strncmp(header->name, "A335BNLT", HDR_NAME_LEN); +} + +static inline int board_is_evm_sk(struct am335x_baseboard_id *header) +{ + return !strncmp("A335X_SK", header->name, HDR_NAME_LEN); +} + +static inline int board_is_idk(struct am335x_baseboard_id *header) +{ + return !strncmp(header->config, "SKU#02", 6); +} + +static inline int board_is_gp_evm(struct am335x_baseboard_id *header) +{ + return !strncmp("A33515BB", header->name, HDR_NAME_LEN); +} + +static inline int board_is_evm_15_or_later(struct am335x_baseboard_id *header) +{ + return (board_is_gp_evm(header) && + strncmp("1.5", header->version, 3) <= 0); +} + /* * We have three pin mux functions that must exist. We must be able to enable * uart0, for initial output and i2c0 to read the main EEPROM. We then have a diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c index 0283708..2e09d98 100644 --- a/board/ti/am335x/mux.c +++ b/board/ti/am335x/mux.c @@ -262,13 +262,13 @@ static unsigned short detect_daughter_board_profile(void) void enable_board_pin_mux(struct am335x_baseboard_id *header) { /* Do board-specific muxes. */ - if (!strncmp(header->name, "A335BONE", HDR_NAME_LEN)) { + if (board_is_bone(header)) { /* Beaglebone pinmux */ configure_module_pin_mux(i2c1_pin_mux); configure_module_pin_mux(mii1_pin_mux); configure_module_pin_mux(mmc0_pin_mux); configure_module_pin_mux(mmc1_pin_mux); - } else if (!strncmp(header->config, "SKU#01", 6)) { + } else if (board_is_gp_evm(header)) { /* General Purpose EVM */ unsigned short profile = detect_daughter_board_profile(); configure_module_pin_mux(rgmii1_pin_mux); @@ -283,7 +283,7 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) configure_module_pin_mux(mmc1_pin_mux); configure_module_pin_mux(spi0_pin_mux); } - } else if (!strncmp(header->config, "SKU#02", 6)) { + } else if (board_is_idk(header)) { /* * Industrial Motor Control (IDK) * note: IDK console is on UART3 by default. @@ -292,13 +292,13 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header) */ configure_module_pin_mux(mii1_pin_mux); configure_module_pin_mux(mmc0_no_cd_pin_mux); - } else if (!strncmp(header->name, "A335X_SK", HDR_NAME_LEN)) { + } else if (board_is_evm_sk(header)) { /* Starter Kit EVM */ configure_module_pin_mux(i2c1_pin_mux); configure_module_pin_mux(gpio0_7_pin_mux); configure_module_pin_mux(rgmii1_pin_mux); configure_module_pin_mux(mmc0_pin_mux_sk_evm); - } else if (!strncmp(header->name, "A335BNLT", HDR_NAME_LEN)) { + } else if (board_is_bone_lt(header)) { /* Beaglebone LT pinmux */ configure_module_pin_mux(i2c1_pin_mux); configure_module_pin_mux(mii1_pin_mux);