Hi Stephen,
On 25 Oct 2014 23:08, "Stephen Warren" swarren@wwwdotorg.org wrote:
On 10/25/2014 09:47 PM, Simon Glass wrote:
Hi Stephen,
On Oct 25, 2014 9:43 PM, "Stephen Warren" <swarren@wwwdotorg.org mailto:swarren@wwwdotorg.org> wrote:
On 10/21/2014 08:04 PM, Simon Glass wrote:
Hi Stephen,
On 20 October 2014 20:23, Stephen Warren <swarren@wwwdotorg.org
mailto:swarren@wwwdotorg.org> wrote:
On 10/19/2014 09:14 PM, Simon Glass wrote:
Hi Stephen,
On 17 October 2014 20:51, Stephen Warren <swarren@wwwdotorg.org
mailto:swarren@wwwdotorg.org> wrote:
> On 09/30/2014 07:41 PM, Stephen Warren wrote: >> On 09/22/2014 05:30 PM, Simon Glass wrote: >>> This series adds driver model support to the GPIO and serial
drivers used
>>> by Raspberry Pi, and moves Raspberry Pi over to driver model. >>> >>> This requires adding driver model support to the pl01x serial
driver, and
>>> replacing the bcm2835 GPIO driver with a driver model version
(since there
>>> are no longer clients that don't use driver model). >>> >>> See u-boot-dm.git branch rpi-working for the tree this is based
on.
>> >> The series, >> Tested-by: Stephen Warren <swarren@wwwdotorg.org
> > Hmm. I take that back. Patch 4 causes a problem, at least when
applied
> on top of u-boot/master from today. > > Basic serial output works just fine, and I can interact with
U-Boot
> without issue. However, when the boot scripts execute and load an > extlinux.conf, U-Boot hangs. Up to patch 3, everything is fine. > > U-Boot 2014.10-00004-g7830ed7 (Oct 17 2014 - 20:47:19) > > DRAM: 480 MiB > WARNING: Caches not enabled > MMC: bcm2835_sdhci: 0 > Using default environment > > In: serial > Out: lcd > Err: lcd > reading /uEnv.txt > 24 bytes read in 14 ms (1000 Bytes/s) > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0... > Found /extlinux/extlinux.conf > Retrieving file: /extlinux/extlinux.conf > reading /extlinux/extlinux.conf > (U-Boot hangs here) >
Can you please point me to where I can get an image to try this
with?
Also did you check with dm/next? There may be dependent patches, although the nature of the problem suggests not.
I use (a pretty old version of, but I doubt that matters) RPi Foundation's Raspbian image, and compiled the kernel and U-Boot according to:
http://elinux.org/index.php?title=RPi_Upstream_Kernel_Compilation&oldid=...
I installed the Raspbian image but I don't get uImg.txt nor the same boot sequence. I am able to boot a kernel though.
Do you have your settings or images uploaded somewhere? Also please confirm you used dm/next.
FWIW, the content in the following branches does seem to work:
u-boot/master 5b3ee38 kbuild: clear VENDOR variable to fix build error on tcsh
u-boot-dm/master c2ded96 serial: remove uniphier_serial_initialize() call
In what way?
I ran U-Boot, and let it boot a kernel via extlinux.conf.
Ok that is probably just because I didn't pull in the patch you said was a problem.
Note that I said it worked, not that it failed.
I did misread this...
Regards, Simon