There is no reason to duplicate code for DRA7xx platforms as there can be Rail grouping. The maximum voltage detection algorithm can still be run on other platforms with no Rail grouping and does not harm as it gives the same result.
Signed-off-by: Lokesh Vutla lokeshvutla@ti.com --- arch/arm/cpu/armv7/omap-common/clocks-common.c | 62 +++++--------------------- 1 file changed, 10 insertions(+), 52 deletions(-)
diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c index 7e5e752..9b97583 100644 --- a/arch/arm/cpu/armv7/omap-common/clocks-common.c +++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c @@ -529,7 +529,6 @@ void __weak recalibrate_iodelay(void) */ void scale_vcores(struct vcores_data const *vcores) { -#if defined(CONFIG_DRA7XX) int i; struct volts *pv = (struct volts *)vcores; struct volts *px; @@ -589,7 +588,16 @@ void scale_vcores(struct vcores_data const *vcores) vcores->mpu.abb_tx_done_mask, OMAP_ABB_FAST_OPP);
- /* The .mm member is not used for the DRA7xx */ + debug("mm: %d\n", vcores->mm.value); + do_scale_vcore(vcores->mm.addr, vcores->mm.value, vcores->mm.pmic); + /* Configure MM ABB LDO after scale */ + abb_setup(vcores->mm.efuse.reg, + (*ctrl)->control_wkup_ldovbb_mm_voltage_ctrl, + (*prcm)->prm_abbldo_mm_setup, + (*prcm)->prm_abbldo_mm_ctrl, + (*prcm)->prm_irqstatus_mpu, + vcores->mm.abb_tx_done_mask, + OMAP_ABB_FAST_OPP);
debug("gpu: %d\n", vcores->gpu.value); do_scale_vcore(vcores->gpu.addr, vcores->gpu.value, vcores->gpu.pmic); @@ -621,56 +629,6 @@ void scale_vcores(struct vcores_data const *vcores) (*prcm)->prm_irqstatus_mpu, vcores->iva.abb_tx_done_mask, OMAP_ABB_FAST_OPP); - /* Might need udelay(1000) here if debug is enabled to see all prints */ -#else - u32 val; - - val = optimize_vcore_voltage(&vcores->core); - do_scale_vcore(vcores->core.addr, val, vcores->core.pmic); - - /* - * IO delay recalibration should be done immediately after - * adjusting AVS voltages for VDD_CORE_L. - * Respective boards should call __recalibrate_iodelay() - * with proper mux, virtual and manual mode configurations. - */ -#ifdef CONFIG_IODELAY_RECALIBRATION - recalibrate_iodelay(); -#endif - - val = optimize_vcore_voltage(&vcores->mpu); - do_scale_vcore(vcores->mpu.addr, val, vcores->mpu.pmic); - - /* Configure MPU ABB LDO after scale */ - abb_setup(vcores->mpu.efuse.reg, - (*ctrl)->control_wkup_ldovbb_mpu_voltage_ctrl, - (*prcm)->prm_abbldo_mpu_setup, - (*prcm)->prm_abbldo_mpu_ctrl, - (*prcm)->prm_irqstatus_mpu_2, - vcores->mpu.abb_tx_done_mask, - OMAP_ABB_FAST_OPP); - - val = optimize_vcore_voltage(&vcores->mm); - do_scale_vcore(vcores->mm.addr, val, vcores->mm.pmic); - - /* Configure MM ABB LDO after scale */ - abb_setup(vcores->mm.efuse.reg, - (*ctrl)->control_wkup_ldovbb_mm_voltage_ctrl, - (*prcm)->prm_abbldo_mm_setup, - (*prcm)->prm_abbldo_mm_ctrl, - (*prcm)->prm_irqstatus_mpu, - vcores->mm.abb_tx_done_mask, - OMAP_ABB_FAST_OPP); - - val = optimize_vcore_voltage(&vcores->gpu); - do_scale_vcore(vcores->gpu.addr, val, vcores->gpu.pmic); - - val = optimize_vcore_voltage(&vcores->eve); - do_scale_vcore(vcores->eve.addr, val, vcores->eve.pmic); - - val = optimize_vcore_voltage(&vcores->iva); - do_scale_vcore(vcores->iva.addr, val, vcores->iva.pmic); -#endif }
static inline void enable_clock_domain(u32 const clkctrl_reg, u32 enable_mode)