RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This patch lets proper packets to be transmitted over the network.
Signed-off-by: Amit Singh Tomar amittomer25@gmail.com --- Changes since v2: * Newly added patch, not there in v2/v1. --- drivers/net/phy/Kconfig | 9 +++++++++ drivers/net/phy/realtek.c | 35 +++++++++++++++++++++++++++++++++++ 2 files changed, 44 insertions(+)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index dceea15..bdf6a2d 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -235,6 +235,15 @@ config RTL8211F_PHY_FORCE_EEE_RXC_ON Default n, which means that the PHY state is not changed. To work around the issues, change this setting to y.
+config RTL8201F_PHY_S700_RMII_TIMINGS + bool "Ethernet PHY RTL8201F: adjust RMII Tx Interface timings" + depends on PHY_REALTEK + help + This provides an option to configure specific timing requirements (needed + for proper PHY operations) for the PHY module present on ACTION SEMI S700 + based cubieboard7. Exact timing requiremnets seems to be SoC specific + (and it's undocumented) that comes from vendor code itself. + config PHY_SMSC bool "Microchip(SMSC) Ethernet PHYs support"
diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c index b9c373b..a549a10 100644 --- a/drivers/net/phy/realtek.c +++ b/drivers/net/phy/realtek.c @@ -13,6 +13,7 @@ #define PHY_RTL8211x_FORCE_MASTER BIT(1) #define PHY_RTL8211E_PINE64_GIGABIT_FIX BIT(2) #define PHY_RTL8211F_FORCE_EEE_RXC_ON BIT(3) +#define PHY_RTL8201F_S700_RMII_TIMINGS BIT(4)
#define PHY_AUTONEGOTIATE_TIMEOUT 5000
@@ -58,6 +59,15 @@ #define MIIM_RTL8211F_TX_DELAY 0x100 #define MIIM_RTL8211F_LCR 0x10
+#define RTL8201F_RMSR 0x10 + +#define RMSR_RX_TIMING_SHIFT BIT(2) +#define RMSR_RX_TIMING_MASK GENMASK(7, 4) +#define RMSR_RX_TIMING_VAL 0x4 +#define RMSR_TX_TIMING_SHIFT BIT(3) +#define RMSR_TX_TIMING_MASK GENMASK(11, 8) +#define RMSR_TX_TIMING_VAL 0x5 + static int rtl8211f_phy_extread(struct phy_device *phydev, int addr, int devaddr, int regnum) { @@ -112,6 +122,15 @@ static int rtl8211f_probe(struct phy_device *phydev) return 0; }
+static int rtl8210f_probe(struct phy_device *phydev) +{ +#ifdef CONFIG_RTL8201F_PHY_S700_RMII_TIMINGS + phydev->flags |= PHY_RTL8201F_S700_RMII_TIMINGS; +#endif + + return 0; +} + /* RealTek RTL8211x */ static int rtl8211x_config(struct phy_device *phydev) { @@ -160,6 +179,21 @@ static int rtl8211x_config(struct phy_device *phydev) /* RealTek RTL8201F */ static int rtl8201f_config(struct phy_device *phydev) { + unsigned int reg; + + if (phydev->flags & PHY_RTL8201F_S700_RMII_TIMINGS) { + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, + 7); + reg = phy_read(phydev, MDIO_DEVAD_NONE, RTL8201F_RMSR); + reg &= ~(RMSR_RX_TIMING_MASK | RMSR_TX_TIMING_MASK); + /* Set the needed Rx/Tx Timings for proper PHY operation */ + reg |= (RMSR_RX_TIMING_VAL << RMSR_RX_TIMING_SHIFT) + | (RMSR_TX_TIMING_VAL << RMSR_TX_TIMING_SHIFT); + phy_write(phydev, MDIO_DEVAD_NONE, RTL8201F_RMSR, reg); + phy_write(phydev, MDIO_DEVAD_NONE, MIIM_RTL8211F_PAGE_SELECT, + 0); + } + genphy_config_aneg(phydev);
return 0; @@ -400,6 +434,7 @@ static struct phy_driver RTL8201F_driver = { .uid = 0x1cc816, .mask = 0xffffff, .features = PHY_BASIC_FEATURES, + .probe = &rtl8210f_probe, .config = &rtl8201f_config, .startup = &rtl8211e_startup, .shutdown = &genphy_shutdown,