From: Meenakshi Aggarwal meenakshi.aggarwal@nxp.com
This patch add base support for LX2162AQDS board. LX2162 is LX2160 based SoC, it has same die as of LX2160 with different packaging. LX2162A support 4GB ddr memory, i2c, micro-click module, microSD card, serial console, qspi nor flash, qsgmii, sgmii, 25g, 40g, 50g network interface,one usb 3.0 and serdes interface to support three x1gen3 pcie interface.
Signed-off-by: Ioana Ciornei ioana.ciornei@nxp.com Signed-off-by: Zhao Qiang qiang.zhao@nxp.com Signed-off-by: hui.song hui.song_1@nxp.com Signed-off-by: Manish Tomar manish.tomar@nxp.com Signed-off-by: Vikas Singh vikas.singh@nxp.com Signed-off-by: Meenakshi Aggarwal meenakshi.aggarwal@nxp.com --- arch/arm/Kconfig | 12 + arch/arm/dts/Makefile | 6 +- arch/arm/dts/fsl-lx2160a-qds.dtsi | 16 +- arch/arm/dts/fsl-lx2162a-qds-17-x.dts | 17 + arch/arm/dts/fsl-lx2162a-qds-18-x.dts | 17 + arch/arm/dts/fsl-lx2162a-qds-20-x.dts | 17 + arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi | 58 ++ arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi | 61 ++ arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi | 26 + arch/arm/dts/fsl-lx2162a-qds.dts | 36 + board/freescale/lx2160a/Kconfig | 16 + board/freescale/lx2160a/MAINTAINERS | 12 +- board/freescale/lx2160a/Makefile | 1 + board/freescale/lx2160a/eth_lx2162aqds.c | 974 +++++++++++++++++++++++++ board/freescale/lx2160a/lx2160a.c | 42 +- configs/lx2162aqds_tfa_SECURE_BOOT_defconfig | 97 +++ configs/lx2162aqds_tfa_defconfig | 95 +++ configs/lx2162aqds_tfa_verified_boot_defconfig | 102 +++ include/configs/lx2160a_common.h | 2 + include/configs/lx2162aqds.h | 169 +++++ 20 files changed, 1753 insertions(+), 23 deletions(-) create mode 100644 arch/arm/dts/fsl-lx2162a-qds-17-x.dts create mode 100644 arch/arm/dts/fsl-lx2162a-qds-18-x.dts create mode 100644 arch/arm/dts/fsl-lx2162a-qds-20-x.dts create mode 100644 arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi create mode 100644 arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi create mode 100644 arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi create mode 100644 arch/arm/dts/fsl-lx2162a-qds.dts create mode 100644 board/freescale/lx2160a/eth_lx2162aqds.c create mode 100644 configs/lx2162aqds_tfa_SECURE_BOOT_defconfig create mode 100644 configs/lx2162aqds_tfa_defconfig create mode 100644 configs/lx2162aqds_tfa_verified_boot_defconfig create mode 100644 include/configs/lx2162aqds.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 80702c2..4bcbcc5 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1321,6 +1321,18 @@ config TARGET_LX2160AQDS is a high-performance development platform that supports the QorIQ LX2160A/LX2120A/LX2080A Layerscape Architecture processor.
+config TARGET_LX2162AQDS + bool "Support lx2162aqds" + select ARCH_LX2160A + select ARCH_MISC_INIT + select ARM64 + select ARMV8_MULTIENTRY + select ARCH_SUPPORT_TFABOOT + select BOARD_LATE_INIT + help + Support for NXP LX2162AQDS platform. + The lx2162aqds support is based on LX2160A Layerscape Architecture processor. + config TARGET_HIKEY bool "Support HiKey 96boards Consumer Edition Platform" select ARM64 diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index f8f5294..a34a56e 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -409,7 +409,11 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \ fsl-lx2160a-qds-19-x-x.dtb \ fsl-lx2160a-qds-19-11-x.dtb \ fsl-lx2160a-qds-20-x-x.dtb \ - fsl-lx2160a-qds-20-11-x.dtb + fsl-lx2160a-qds-20-11-x.dtb \ + fsl-lx2162a-qds.dtb\ + fsl-lx2162a-qds-17-x.dtb\ + fsl-lx2162a-qds-18-x.dtb\ + fsl-lx2162a-qds-20-x.dtb dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \ fsl-ls1043a-qds-lpuart.dtb \ fsl-ls1043a-rdb.dtb \ diff --git a/arch/arm/dts/fsl-lx2160a-qds.dtsi b/arch/arm/dts/fsl-lx2160a-qds.dtsi index 96c9800..370f116 100644 --- a/arch/arm/dts/fsl-lx2160a-qds.dtsi +++ b/arch/arm/dts/fsl-lx2160a-qds.dtsi @@ -2,7 +2,7 @@ /* * NXP LX2160AQDS common device tree source * - * Copyright 2018-2019 NXP + * Copyright 2018-2020 NXP * */
@@ -251,6 +251,20 @@ }; };
+&fspi { + status = "okay"; + + mt35xu512aba0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + spi-rx-bus-width = <8>; + spi-tx-bus-width = <1>; + }; +}; + &sata0 { status = "okay"; }; diff --git a/arch/arm/dts/fsl-lx2162a-qds-17-x.dts b/arch/arm/dts/fsl-lx2162a-qds-17-x.dts new file mode 100644 index 0000000..8a8895f --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-17-x.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for SERDES protocol 17.x + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2162a-qds-sd1-17.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board (DTS 17.x)"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-18-x.dts b/arch/arm/dts/fsl-lx2162a-qds-18-x.dts new file mode 100644 index 0000000..c28e5e2 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-18-x.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for SERDES protocol 18.x + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2162a-qds-sd1-18.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board (DTS 18.x)"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-20-x.dts b/arch/arm/dts/fsl-lx2162a-qds-20-x.dts new file mode 100644 index 0000000..7882c76 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-20-x.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for SERDES protocol 20.x + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2162a-qds-sd1-20.dtsi" + +/ { + model = "NXP Layerscape LX2160AQDS Board (DTS 20.x)"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi new file mode 100644 index 0000000..60f5a4e --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-17.dtsi @@ -0,0 +1,58 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for the SERDES block #1 - protocol 17 + * + * Some assumptions are made: + * * mezzanine card M8 is connected to IO SLOT1 (25g-aui for DPMAC 3,4,5,6) + * + * Copyright 2020 NXP + * + */ + +#include "fsl-lx2160a-qds.dtsi" + +&dpmac3 { + status = "okay"; + phy-handle = <&inphi_phy0>; + phy-connection-type = "25g-aui"; +}; + +&dpmac4 { + status = "okay"; + phy-handle = <&inphi_phy1>; + phy-connection-type = "25g-aui"; +}; + +&dpmac5 { + status = "okay"; + phy-handle = <&inphi_phy2>; + phy-connection-type = "25g-aui"; +}; + +&dpmac6 { + status = "okay"; + phy-handle = <&inphi_phy3>; + phy-connection-type = "25g-aui"; +}; + +&emdio1_slot1 { + inphi_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x0>; + }; + + inphi_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x1>; + }; + + inphi_phy2: ethernet-phy@2 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x2>; + }; + + inphi_phy3: ethernet-phy@3 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x3>; + }; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi new file mode 100644 index 0000000..8e11b06 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-18.dtsi @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for the SERDES block #1 - protocol 18 + * + * Some assumptions are made: + * * mezzanine card M11 is connected to IO SLOT1 (usxgmii for DPMAC 3,4) + * * mezzanine card M13/M8 is connected to IO SLOT6 (25g-aui for DPMAC 5,6) + * + * Copyright 2020 NXP + * + */ + +#include "fsl-lx2160a-qds.dtsi" + +&dpmac3 { + status = "okay"; + phy-handle = <&aquantia_phy1>; + phy-connection-type = "usxgmii"; +}; + +&dpmac4 { + status = "okay"; + phy-handle = <&aquantia_phy2>; + phy-connection-type = "usxgmii"; +}; + +&dpmac5 { + status = "okay"; + phy-handle = <&inphi_phy0>; + phy-connection-type = "25g-aui"; +}; + +&dpmac6 { + status = "okay"; + phy-handle = <&inphi_phy1>; + phy-connection-type = "25g-aui"; +}; + +&emdio1_slot1 { + aquantia_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x0>; + }; + + aquantia_phy2: ethernet-phy@5 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x1>; + }; +}; + +&emdio1_slot6 { + inphi_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x0>; + }; + + inphi_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-id0210.7440"; + reg = <0x1>; + }; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi b/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi new file mode 100644 index 0000000..faf4285 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds-sd1-20.dtsi @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source for the SERDES block #1 - protocol 20 + * + * Some assumptions are made: + * * Mezzanine card M8 is connected to IO SLOT1 + * (xlaui4 for DPMAC 1) + * + * Copyright 2020 NXP + * + */ + +#include "fsl-lx2160a-qds.dtsi" + +&dpmac1 { + status = "okay"; + phy-handle = <&cortina_phy1_0>; + phy-connection-type = "xlaui4"; +}; + +&emdio1_slot1 { + cortina_phy1_0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x0>; + }; +}; diff --git a/arch/arm/dts/fsl-lx2162a-qds.dts b/arch/arm/dts/fsl-lx2162a-qds.dts new file mode 100644 index 0000000..2195607 --- /dev/null +++ b/arch/arm/dts/fsl-lx2162a-qds.dts @@ -0,0 +1,36 @@ +// SPDX-License-Identifier: GPL-2.0+ OR X11 +/* + * NXP LX2162AQDS device tree source + * + * Copyright 2020 NXP + * + */ + +/dts-v1/; + +#include "fsl-lx2160a-qds.dtsi" + +/ { + model = "NXP Layerscape LX2162AQDS Board"; + compatible = "fsl,lx2162aqds", "fsl,lx2160a"; + + aliases { + spi0 = &fspi; + + pcie@3500000 { + status = "disabled"; + }; + + pcie@3800000 { + status = "disabled"; + }; + + pcie@3900000 { + status = "disabled"; + }; + }; +}; + +&usb1 { + status = "disabled"; +}; diff --git a/board/freescale/lx2160a/Kconfig b/board/freescale/lx2160a/Kconfig index 122a385..7556f7d 100644 --- a/board/freescale/lx2160a/Kconfig +++ b/board/freescale/lx2160a/Kconfig @@ -32,3 +32,19 @@ config SYS_CONFIG_NAME source "board/freescale/common/Kconfig" endif
+if TARGET_LX2162AQDS + +config SYS_BOARD + default "lx2160a" + +config SYS_VENDOR + default "freescale" + +config SYS_SOC + default "fsl-layerscape" + +config SYS_CONFIG_NAME + default "lx2162aqds" + +source "board/freescale/common/Kconfig" +endif diff --git a/board/freescale/lx2160a/MAINTAINERS b/board/freescale/lx2160a/MAINTAINERS index 9fe79c0..4a78155 100644 --- a/board/freescale/lx2160a/MAINTAINERS +++ b/board/freescale/lx2160a/MAINTAINERS @@ -1,5 +1,6 @@ LX2160ARDB BOARD -M: Priyanka Jain priyanka.jain@nxp.com +M: Meenakshi Aggarwal meenakshi.aggarwal@nxp.com +M: Priyanka Jain priyanka.jain@nxp.com S: Maintained F: board/freescale/lx2160a/ F: include/configs/lx2160a_common.h @@ -14,6 +15,7 @@ S: Maintained F: configs/lx2160ardb_tfa_SECURE_BOOT_defconfig
LX2160AQDS BOARD +M: Meenakshi Aggarwal meenakshi.aggarwal@nxp.com M: Pankaj Bansal pankaj.bansal@nxp.com S: Maintained F: board/freescale/lx2160a/eth_lx2160aqds.h @@ -25,3 +27,11 @@ LX2160AQDS_SECURE_BOOT BOARD M: Udit Agarwal udit.agarwal@nxp.com S: Maintained F: configs/lx2160aqds_tfa_SECURE_BOOT_defconfig + +LX2162AQDS BOARD +M: Meenakshi Aggarwal meenakshi.aggarwal@nxp.com +S: Maintained +F: board/freescale/lx2160a/eth_lx2162aqds.h +F: include/configs/lx2162aqds.h +F: configs/lx2162aqds_tfa_defconfig +F: arch/arm/dts/fsl-lx2162a-qds.dts diff --git a/board/freescale/lx2160a/Makefile b/board/freescale/lx2160a/Makefile index d1a621b..c9561bf 100644 --- a/board/freescale/lx2160a/Makefile +++ b/board/freescale/lx2160a/Makefile @@ -8,3 +8,4 @@ obj-y += lx2160a.o obj-y += ddr.o obj-$(CONFIG_TARGET_LX2160ARDB) += eth_lx2160ardb.o obj-$(CONFIG_TARGET_LX2160AQDS) += eth_lx2160aqds.o +obj-$(CONFIG_TARGET_LX2162AQDS) += eth_lx2162aqds.o diff --git a/board/freescale/lx2160a/eth_lx2162aqds.c b/board/freescale/lx2160a/eth_lx2162aqds.c new file mode 100644 index 0000000..309eea6 --- /dev/null +++ b/board/freescale/lx2160a/eth_lx2162aqds.c @@ -0,0 +1,974 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 NXP + * + */ + +#include <common.h> +#include <env.h> +#include <fdt_support.h> +#include <hwconfig.h> +#include <command.h> +#include <log.h> +#include <net.h> +#include <netdev.h> +#include <malloc.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <fm_eth.h> +#include <asm/io.h> +#include <exports.h> +#include <asm/arch/fsl_serdes.h> +#include <fsl-mc/fsl_mc.h> +#include <fsl-mc/ldpaa_wriop.h> +#include <linux/libfdt.h> + +#include "../common/qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +#ifndef CONFIG_DM_ETH +#define EMI_NONE 0 +#define EMI1 1 /* Mdio Bus 1 */ +#define EMI2 2 /* Mdio Bus 2 */ + +#if defined(CONFIG_FSL_MC_ENET) +enum io_slot { + IO_SLOT_NONE = 0, + IO_SLOT_1, + IO_SLOT_2, + IO_SLOT_3, + IO_SLOT_4, + IO_SLOT_5, + IO_SLOT_6, + IO_SLOT_7, + IO_SLOT_8, + EMI1_RGMII1, + EMI1_RGMII2, + IO_SLOT_MAX +}; + +struct lx2162a_qds_mdio { + enum io_slot ioslot : 4; + u8 realbusnum : 4; + struct mii_dev *realbus; +}; + +/* structure explaining the phy configuration on 8 lanes of a serdes*/ +struct serdes_phy_config { + u8 serdes; /* serdes protocol */ + struct phy_config { + u8 dpmacid; + /* -1 terminated array */ + int phy_address[WRIOP_MAX_PHY_NUM + 1]; + u8 mdio_bus; + enum io_slot ioslot; + } phy_config[SRDS_MAX_LANES]; +}; + +/* Table defining the phy configuration on 8 lanes of a serdes. + * Various assumptions have been made while defining this table. + * e.g. for serdes1 protocol 19 it is being assumed that X-M11-USXGMII + * card is being used for dpmac 3-4. (X-M12-XFI could also have been used) + * And also that this card is connected to IO Slot 1 (could have been connected + * to any of the 8 IO slots (IO slot 1 - IO slot 8)). + * similarly, it is also being assumed that MDIO 1 is selected on X-M7-40G card + * used in serdes1 protocol 19 (could have selected MDIO 2) + * To override these settings "dpmac" environment variable can be used after + * defining "dpmac_override" in hwconfig environment variable. + * This table has limited serdes protocol entries. It can be expanded as per + * requirement. + */ +/***************************************************************** + | SERDES_1 PROTOCOL | IO_SLOT | CARD | + ***************************************************************** + | 2 | IO_SLOT_1 | M4-PCIE-SGMII | + | 3 | IO_SLOT_1 | M11-USXGMII | + | 15 | IO_SLOT_1 | M13-25G | + | 17 | IO_SLOT_1 | M13-25G | + | 18 | IO_SLOT_1 | M11-USXGMII | + | | IO_SLOT_6 | M13-25G | + | 20 | IO_SLOT_1 | M7-40G | + ***************************************************************** + */ +static const struct serdes_phy_config serdes1_phy_config[] = { + {1, {} }, + {2, {{WRIOP1_DPMAC3, {SGMII_CARD_PORT1_PHY_ADDR, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_1} } }, + {3, {{WRIOP1_DPMAC3, {AQ_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {AQ_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {AQ_PHY_ADDR3, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {AQ_PHY_ADDR4, -1}, + EMI1, IO_SLOT_1} } }, + {15, {{WRIOP1_DPMAC1, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC2, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1} } }, + {17, {{WRIOP1_DPMAC3, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC6, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1} } }, + {18, {{WRIOP1_DPMAC3, {AQ_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC4, {AQ_PHY_ADDR2, -1}, + EMI1, IO_SLOT_1}, + {WRIOP1_DPMAC5, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_6}, + {WRIOP1_DPMAC6, {INPHI_PHY_ADDR1, INPHI_PHY_ADDR2, -1}, + EMI1, IO_SLOT_6} } }, + {20, {{WRIOP1_DPMAC1, {CORTINA_PHY_ADDR1, -1}, + EMI1, IO_SLOT_1} } } +}; + +/***************************************************************** + | SERDES_2 PROTOCOL | IO_SLOT | CARD | + ***************************************************************** + | 2 | IO_SLOT_7 | M4-PCIE-SGMII | + | | IO_SLOT_8 | M4-PCIE-SGMII | + | 3 | IO_SLOT_7 | M4-PCIE-SGMII | + | | IO_SLOT_8 | M4-PCIE-SGMII | + | 5 | IO_SLOT_7 | M4-PCIE-SGMII | + | 10 | IO_SLOT_7 | M4-PCIE-SGMII | + | | IO_SLOT_8 | M4-PCIE-SGMII | + | 11 | IO_SLOT_7 | M4-PCIE-SGMII | + | | IO_SLOT_8 | M4-PCIE-SGMII | + | 12 | IO_SLOT_7 | M4-PCIE-SGMII | + | | IO_SLOT_8 | M4-PCIE-SGMII | + ***************************************************************** + */ +static const struct serdes_phy_config serdes2_phy_config[] = { + {2, {} }, + {3, {} }, + {5, {} }, + {10, {{WRIOP1_DPMAC11, {SGMII_CARD_PORT1_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC12, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC17, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC18, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_7} } }, + {11, {{WRIOP1_DPMAC12, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC17, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC18, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC16, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_8}, + {WRIOP1_DPMAC13, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_8}, + {WRIOP1_DPMAC14, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_8} } }, + {12, {{WRIOP1_DPMAC11, {SGMII_CARD_PORT1_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC12, {SGMII_CARD_PORT2_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC17, {SGMII_CARD_PORT3_PHY_ADDR, -1}, + EMI1, IO_SLOT_7}, + {WRIOP1_DPMAC18, {SGMII_CARD_PORT4_PHY_ADDR, -1}, + EMI1, IO_SLOT_7} } } +}; + +static inline +const struct phy_config *get_phy_config(u8 serdes, + const struct serdes_phy_config *table, + u8 table_size) +{ + int i; + + for (i = 0; i < table_size; i++) { + if (table[i].serdes == serdes) + return table[i].phy_config; + } + + return NULL; +} + +/* BRDCFG4 controls EMI routing for the board. + * Bits Function + * 7-6 EMI Interface #1 Primary Routing (CFG_MUX1_EMI1) (1.8V): + * EMI1 00= On-board PHY #1 + * 01= On-board PHY #2 + * 10= (reserved) + * 11= Slots 1..8 multiplexer and translator. + * 5-3 EMI Interface #1 Secondary Routing (CFG_MUX2_EMI1) (2.5V): + * EMI1X 000= Slot #1 + * 001= Slot #2 + * 010= Slot #3 + * 011= Slot #4 + * 100= Slot #5 + * 101= Slot #6 + * 110= Slot #7 + * 111= Slot #8 + * 2-0 EMI Interface #2 Routing (CFG_MUX_EMI2): + * EMI2 000= Slot #1 (secondary EMI) + * 001= Slot #2 (secondary EMI) + * 010= Slot #3 (secondary EMI) + * 011= Slot #4 (secondary EMI) + * 100= Slot #5 (secondary EMI) + * 101= Slot #6 (secondary EMI) + * 110= Slot #7 (secondary EMI) + * 111= Slot #8 (secondary EMI) + */ +static int lx2162a_qds_get_mdio_mux_val(u8 realbusnum, enum io_slot ioslot) +{ + switch (realbusnum) { + case EMI1: + switch (ioslot) { + case EMI1_RGMII1: + return 0; + case EMI1_RGMII2: + return 0x40; + default: + return (((ioslot - 1) << BRDCFG4_EMI1SEL_SHIFT) | 0xC0); + } + break; + case EMI2: + return ((ioslot - 1) << BRDCFG4_EMI2SEL_SHIFT); + default: + return -1; + } +} + +static void lx2162a_qds_mux_mdio(struct lx2162a_qds_mdio *priv) +{ + u8 brdcfg4, mux_val, reg; + + brdcfg4 = QIXIS_READ(brdcfg[4]); + reg = brdcfg4; + mux_val = lx2162a_qds_get_mdio_mux_val(priv->realbusnum, priv->ioslot); + + switch (priv->realbusnum) { + case EMI1: + brdcfg4 &= ~BRDCFG4_EMI1SEL_MASK; + brdcfg4 |= mux_val; + break; + case EMI2: + brdcfg4 &= ~BRDCFG4_EMI2SEL_MASK; + brdcfg4 |= mux_val; + break; + } + + if (brdcfg4 ^ reg) + QIXIS_WRITE(brdcfg[4], brdcfg4); +} + +static int lx2162a_qds_mdio_read(struct mii_dev *bus, int addr, + int devad, int regnum) +{ + struct lx2162a_qds_mdio *priv = bus->priv; + + lx2162a_qds_mux_mdio(priv); + + return priv->realbus->read(priv->realbus, addr, devad, regnum); +} + +static int lx2162a_qds_mdio_write(struct mii_dev *bus, int addr, int devad, + int regnum, u16 value) +{ + struct lx2162a_qds_mdio *priv = bus->priv; + + lx2162a_qds_mux_mdio(priv); + + return priv->realbus->write(priv->realbus, addr, devad, regnum, value); +} + +static int lx2162a_qds_mdio_reset(struct mii_dev *bus) +{ + struct lx2162a_qds_mdio *priv = bus->priv; + + return priv->realbus->reset(priv->realbus); +} + +static struct mii_dev *lx2162a_qds_mdio_init(u8 realbusnum, enum io_slot ioslot) +{ + struct lx2162a_qds_mdio *pmdio; + struct mii_dev *bus; + /*should be within MDIO_NAME_LEN*/ + char dummy_mdio_name[] = "LX2162A_QDS_MDIO1_IOSLOT1"; + + if (realbusnum == EMI2) { + if (ioslot < IO_SLOT_1 || ioslot > IO_SLOT_8) { + printf("invalid ioslot %d\n", ioslot); + return NULL; + } + } else if (realbusnum == EMI1) { + if (ioslot < IO_SLOT_1 || ioslot > EMI1_RGMII2) { + printf("invalid ioslot %d\n", ioslot); + return NULL; + } + } else { + printf("not supported real mdio bus %d\n", realbusnum); + return NULL; + } + + if (ioslot == EMI1_RGMII1) + strcpy(dummy_mdio_name, "LX2162A_QDS_MDIO1_RGMII1"); + else if (ioslot == EMI1_RGMII2) + strcpy(dummy_mdio_name, "LX2162A_QDS_MDIO1_RGMII2"); + else + sprintf(dummy_mdio_name, "LX2162A_QDS_MDIO%d_IOSLOT%d", + realbusnum, ioslot); + bus = miiphy_get_dev_by_name(dummy_mdio_name); + + if (bus) + return bus; + + bus = mdio_alloc(); + if (!bus) { + printf("Failed to allocate %s bus\n", dummy_mdio_name); + return NULL; + } + + pmdio = malloc(sizeof(*pmdio)); + if (!pmdio) { + printf("Failed to allocate %s private data\n", dummy_mdio_name); + free(bus); + return NULL; + } + + switch (realbusnum) { + case EMI1: + pmdio->realbus = + miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO1_NAME); + break; + case EMI2: + pmdio->realbus = + miiphy_get_dev_by_name(DEFAULT_WRIOP_MDIO2_NAME); + break; + } + + if (!pmdio->realbus) { + printf("No real mdio bus num %d found\n", realbusnum); + free(bus); + free(pmdio); + return NULL; + } + + pmdio->realbusnum = realbusnum; + pmdio->ioslot = ioslot; + bus->read = lx2162a_qds_mdio_read; + bus->write = lx2162a_qds_mdio_write; + bus->reset = lx2162a_qds_mdio_reset; + strcpy(bus->name, dummy_mdio_name); + bus->priv = pmdio; + + if (!mdio_register(bus)) + return bus; + + printf("No bus with name %s\n", dummy_mdio_name); + free(bus); + free(pmdio); + return NULL; +} + +static inline void do_phy_config(const struct phy_config *phy_config) +{ + struct mii_dev *bus; + int i, phy_num, phy_address; + + for (i = 0; i < SRDS_MAX_LANES; i++) { + if (!phy_config[i].dpmacid) + continue; + + for (phy_num = 0; + phy_num < ARRAY_SIZE(phy_config[i].phy_address); + phy_num++) { + phy_address = phy_config[i].phy_address[phy_num]; + if (phy_address == -1) + break; + wriop_set_phy_address(phy_config[i].dpmacid, + phy_num, phy_address); + } + /*Register the muxing front-ends to the MDIO buses*/ + bus = lx2162a_qds_mdio_init(phy_config[i].mdio_bus, + phy_config[i].ioslot); + if (!bus) + printf("could not get bus for mdio %d ioslot %d\n", + phy_config[i].mdio_bus, + phy_config[i].ioslot); + else + wriop_set_mdio(phy_config[i].dpmacid, bus); + } +} + +static inline void do_dpmac_config(int dpmac, const char *arg_dpmacid, + char *env_dpmac) +{ + const char *ret; + size_t len; + u8 realbusnum, ioslot; + struct mii_dev *bus; + int phy_num; + char *phystr = "phy00"; + + /*search phy in dpmac arg*/ + for (phy_num = 0; phy_num < WRIOP_MAX_PHY_NUM; phy_num++) { + sprintf(phystr, "phy%d", phy_num + 1); + ret = hwconfig_subarg_f(arg_dpmacid, phystr, &len, env_dpmac); + if (!ret) { + /*look for phy instead of phy1*/ + if (!phy_num) + ret = hwconfig_subarg_f(arg_dpmacid, "phy", + &len, env_dpmac); + if (!ret) + continue; + } + + if (len != 4 || strncmp(ret, "0x", 2)) + printf("invalid phy format in %s variable.\n" + "specify phy%d for %s in hex format e.g. 0x12\n", + env_dpmac, phy_num + 1, arg_dpmacid); + else + wriop_set_phy_address(dpmac, phy_num, + simple_strtoul(ret, NULL, 16)); + } + + /*search mdio in dpmac arg*/ + ret = hwconfig_subarg_f(arg_dpmacid, "mdio", &len, env_dpmac); + if (ret) + realbusnum = *ret - '0'; + else + realbusnum = EMI_NONE; + + if (realbusnum) { + /*search io in dpmac arg*/ + ret = hwconfig_subarg_f(arg_dpmacid, "io", &len, env_dpmac); + if (ret) + ioslot = *ret - '0'; + else + ioslot = IO_SLOT_NONE; + /*Register the muxing front-ends to the MDIO buses*/ + bus = lx2162a_qds_mdio_init(realbusnum, ioslot); + if (!bus) + printf("could not get bus for mdio %d ioslot %d\n", + realbusnum, ioslot); + else + wriop_set_mdio(dpmac, bus); + } +} + +#endif +#endif /* !CONFIG_DM_ETH */ + +int board_eth_init(struct bd_info *bis) +{ +#ifndef CONFIG_DM_ETH +#if defined(CONFIG_FSL_MC_ENET) + struct memac_mdio_info mdio_info; + struct memac_mdio_controller *regs; + int i; + const char *ret; + char *env_dpmac; + char dpmacid[] = "dpmac00", srds[] = "00_00_00"; + size_t len; + struct mii_dev *bus; + const struct phy_config *phy_config; + struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 srds_s1, srds_s2; + + srds_s1 = in_le32(&gur->rcwsr[28]) & + FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK; + srds_s1 >>= FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT; + + srds_s2 = in_le32(&gur->rcwsr[28]) & + FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK; + srds_s2 >>= FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT; + + sprintf(srds, "%d_%d", srds_s1, srds_s2); + + regs = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO1; + mdio_info.regs = regs; + mdio_info.name = DEFAULT_WRIOP_MDIO1_NAME; + + /*Register the EMI 1*/ + fm_memac_mdio_init(bis, &mdio_info); + + regs = (struct memac_mdio_controller *)CONFIG_SYS_FSL_WRIOP1_MDIO2; + mdio_info.regs = regs; + mdio_info.name = DEFAULT_WRIOP_MDIO2_NAME; + + /*Register the EMI 2*/ + fm_memac_mdio_init(bis, &mdio_info); + + /* "dpmac" environment variable can be used after + * defining "dpmac_override" in hwconfig environment variable. + */ + if (hwconfig("dpmac_override")) { + env_dpmac = env_get("dpmac"); + if (env_dpmac) { + ret = hwconfig_arg_f("srds", &len, env_dpmac); + if (ret) { + if (strncmp(ret, srds, strlen(srds))) { + printf("SERDES configuration changed.\n" + "previous: %.*s, current: %s.\n" + "update dpmac variable.\n", + (int)len, ret, srds); + } + } else { + printf("SERDES configuration not found.\n" + "Please add srds:%s in dpmac variable\n", + srds); + } + + for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) { + /* Look for dpmac1 to dpmac24(current max) arg + * in dpmac environment variable + */ + sprintf(dpmacid, "dpmac%d", i); + ret = hwconfig_arg_f(dpmacid, &len, env_dpmac); + if (ret) + do_dpmac_config(i, dpmacid, env_dpmac); + } + } else { + printf("Warning: environment dpmac not found.\n" + "DPAA network interfaces may not work\n"); + } + } else { + /*Look for phy config for serdes1 in phy config table*/ + phy_config = get_phy_config(srds_s1, serdes1_phy_config, + ARRAY_SIZE(serdes1_phy_config)); + if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes1 Protocol %d\n", + __func__, srds_s1); + } else { + do_phy_config(phy_config); + } + phy_config = get_phy_config(srds_s2, serdes2_phy_config, + ARRAY_SIZE(serdes2_phy_config)); + if (!phy_config) { + printf("%s WRIOP: Unsupported SerDes2 Protocol %d\n", + __func__, srds_s2); + } else { + do_phy_config(phy_config); + } + } + + if (wriop_get_enet_if(WRIOP1_DPMAC17) == PHY_INTERFACE_MODE_RGMII_ID) { + wriop_set_phy_address(WRIOP1_DPMAC17, 0, RGMII_PHY_ADDR1); + bus = lx2162a_qds_mdio_init(EMI1, EMI1_RGMII1); + if (!bus) + printf("could not get bus for RGMII1\n"); + else + wriop_set_mdio(WRIOP1_DPMAC17, bus); + } + + if (wriop_get_enet_if(WRIOP1_DPMAC18) == PHY_INTERFACE_MODE_RGMII_ID) { + wriop_set_phy_address(WRIOP1_DPMAC18, 0, RGMII_PHY_ADDR2); + bus = lx2162a_qds_mdio_init(EMI1, EMI1_RGMII2); + if (!bus) + printf("could not get bus for RGMII2\n"); + else + wriop_set_mdio(WRIOP1_DPMAC18, bus); + } + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ +#endif /* !CONFIG_DM_ETH */ + +#ifdef CONFIG_PHY_AQUANTIA + /* + * Export functions to be used by AQ firmware + * upload application + */ + gd->jt->strcpy = strcpy; + gd->jt->mdelay = mdelay; + gd->jt->mdio_get_current_dev = mdio_get_current_dev; + gd->jt->phy_find_by_mask = phy_find_by_mask; + gd->jt->mdio_phydev_for_ethname = mdio_phydev_for_ethname; + gd->jt->miiphy_set_current_dev = miiphy_set_current_dev; +#endif + +#ifdef CONFIG_DM_ETH + return 0; +#else + return pci_eth_init(bis); +#endif +} + +#if defined(CONFIG_RESET_PHY_R) +void reset_phy(void) +{ +#if defined(CONFIG_FSL_MC_ENET) + mc_env_boot(); +#endif +} +#endif /* CONFIG_RESET_PHY_R */ + +#ifndef CONFIG_DM_ETH +#if defined(CONFIG_FSL_MC_ENET) +int fdt_fixup_dpmac_phy_handle(void *fdt, int dpmac_id, int node_phandle) +{ + int offset; + int ret; + char dpmac_str[] = "dpmacs@00"; + const char *phy_string; + + offset = fdt_path_offset(fdt, "/soc/fsl-mc/dpmacs"); + + if (offset < 0) + offset = fdt_path_offset(fdt, "/fsl-mc/dpmacs"); + + if (offset < 0) { + printf("dpmacs node not found in device tree\n"); + return offset; + } + + sprintf(dpmac_str, "dpmac@%x", dpmac_id); + debug("dpmac_str = %s\n", dpmac_str); + + offset = fdt_subnode_offset(fdt, offset, dpmac_str); + if (offset < 0) { + printf("%s node not found in device tree\n", dpmac_str); + return offset; + } + + phy_string = fdt_getprop(fdt, offset, "phy-connection-type", NULL); + if (is_backplane_mode(phy_string)) { + /* Backplane KR mode: skip fixups */ + printf("Interface %d in backplane KR mode\n", dpmac_id); + return 0; + } + + ret = fdt_appendprop_cell(fdt, offset, "phy-handle", node_phandle); + if (ret) + printf("%d@%s %d\n", __LINE__, __func__, ret); + + phy_string = phy_string_for_interface(wriop_get_enet_if(dpmac_id)); + ret = fdt_setprop_string(fdt, offset, "phy-connection-type", + phy_string); + if (ret) + printf("%d@%s %d\n", __LINE__, __func__, ret); + + return ret; +} + +int fdt_get_ioslot_offset(void *fdt, struct mii_dev *mii_dev, int fpga_offset) +{ + char mdio_ioslot_str[] = "mdio@00"; + struct lx2162a_qds_mdio *priv; + u64 reg; + u32 phandle; + int offset, mux_val; + + /*Test if the MDIO bus is real mdio bus or muxing front end ?*/ + if (strncmp(mii_dev->name, "LX2162A_QDS_MDIO", + strlen("LX2162A_QDS_MDIO"))) + return -1; + + /*Get the real MDIO bus num and ioslot info from bus's priv data*/ + priv = mii_dev->priv; + + debug("real_bus_num = %d, ioslot = %d\n", + priv->realbusnum, priv->ioslot); + + if (priv->realbusnum == EMI1) + reg = CONFIG_SYS_FSL_WRIOP1_MDIO1; + else + reg = CONFIG_SYS_FSL_WRIOP1_MDIO2; + + offset = fdt_node_offset_by_compat_reg(fdt, "fsl,fman-memac-mdio", reg); + if (offset < 0) { + printf("mdio@%llx node not found in device tree\n", reg); + return offset; + } + + phandle = fdt_get_phandle(fdt, offset); + phandle = cpu_to_fdt32(phandle); + offset = fdt_node_offset_by_prop_value(fdt, -1, "mdio-parent-bus", + &phandle, 4); + if (offset < 0) { + printf("mdio-mux-%d node not found in device tree\n", + priv->realbusnum == EMI1 ? 1 : 2); + return offset; + } + + mux_val = lx2162a_qds_get_mdio_mux_val(priv->realbusnum, priv->ioslot); + if (priv->realbusnum == EMI1) + mux_val >>= BRDCFG4_EMI1SEL_SHIFT; + else + mux_val >>= BRDCFG4_EMI2SEL_SHIFT; + sprintf(mdio_ioslot_str, "mdio@%x", (u8)mux_val); + + offset = fdt_subnode_offset(fdt, offset, mdio_ioslot_str); + if (offset < 0) { + printf("%s node not found in device tree\n", mdio_ioslot_str); + return offset; + } + + return offset; +} + +int fdt_create_phy_node(void *fdt, int offset, u8 phyaddr, int *subnodeoffset, + struct phy_device *phy_dev, int phandle) +{ + char phy_node_name[] = "ethernet-phy@00"; + char phy_id_compatible_str[] = "ethernet-phy-id0000.0000,"; + int ret; + + sprintf(phy_node_name, "ethernet-phy@%x", phyaddr); + debug("phy_node_name = %s\n", phy_node_name); + + *subnodeoffset = fdt_add_subnode(fdt, offset, phy_node_name); + if (*subnodeoffset <= 0) { + printf("Could not add subnode %s inside node %s err = %s\n", + phy_node_name, fdt_get_name(fdt, offset, NULL), + fdt_strerror(*subnodeoffset)); + return *subnodeoffset; + } + + sprintf(phy_id_compatible_str, "ethernet-phy-id%04x.%04x,", + phy_dev->phy_id >> 16, phy_dev->phy_id & 0xFFFF); + debug("phy_id_compatible_str %s\n", phy_id_compatible_str); + + ret = fdt_setprop_string(fdt, *subnodeoffset, "compatible", + phy_id_compatible_str); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + + if (phy_dev->is_c45) { + ret = fdt_appendprop_string(fdt, *subnodeoffset, "compatible", + "ethernet-phy-ieee802.3-c45"); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + } else { + ret = fdt_appendprop_string(fdt, *subnodeoffset, "compatible", + "ethernet-phy-ieee802.3-c22"); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + } + + ret = fdt_setprop_cell(fdt, *subnodeoffset, "reg", phyaddr); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + + ret = fdt_set_phandle(fdt, *subnodeoffset, phandle); + if (ret) { + printf("%d@%s %d\n", __LINE__, __func__, ret); + goto out; + } + +out: + if (ret) + fdt_del_node(fdt, *subnodeoffset); + + return ret; +} + +#define is_rgmii(dpmac_id) \ + wriop_get_enet_if((dpmac_id)) == PHY_INTERFACE_MODE_RGMII_ID + +int fdt_fixup_board_phy(void *fdt) +{ + int fpga_offset, offset, subnodeoffset; + struct mii_dev *mii_dev; + struct list_head *mii_devs, *entry; + int ret, dpmac_id, phandle, i; + struct phy_device *phy_dev; + char ethname[ETH_NAME_LEN]; + phy_interface_t phy_iface; + + ret = 0; + /* we know FPGA is connected to i2c0, therefore search path directly, + * instead of compatible property, as it saves time + */ + fpga_offset = fdt_path_offset(fdt, "/soc/i2c@2000000/fpga"); + + if (fpga_offset < 0) + fpga_offset = fdt_path_offset(fdt, "/i2c@2000000/fpga"); + + if (fpga_offset < 0) { + printf("i2c@2000000/fpga node not found in device tree\n"); + return fpga_offset; + } + + phandle = fdt_alloc_phandle(fdt); + mii_devs = mdio_get_list_head(); + + list_for_each(entry, mii_devs) { + mii_dev = list_entry(entry, struct mii_dev, link); + debug("mii_dev name : %s\n", mii_dev->name); + offset = fdt_get_ioslot_offset(fdt, mii_dev, fpga_offset); + if (offset < 0) + continue; + + // Look for phy devices attached to MDIO bus muxing front end + // and create their entries with compatible being the device id + for (i = 0; i < PHY_MAX_ADDR; i++) { + phy_dev = mii_dev->phymap[i]; + if (!phy_dev) + continue; + + // TODO: use sscanf instead of loop + dpmac_id = WRIOP1_DPMAC1; + while (dpmac_id < NUM_WRIOP_PORTS) { + phy_iface = wriop_get_enet_if(dpmac_id); + snprintf(ethname, ETH_NAME_LEN, "DPMAC%d@%s", + dpmac_id, + phy_string_for_interface(phy_iface)); + if (strcmp(ethname, phy_dev->dev->name) == 0) + break; + dpmac_id++; + } + if (dpmac_id == NUM_WRIOP_PORTS) + continue; + + if ((dpmac_id == 17 || dpmac_id == 18) && + is_rgmii(dpmac_id)) + continue; + + ret = fdt_create_phy_node(fdt, offset, i, + &subnodeoffset, + phy_dev, phandle); + if (ret) + break; + + ret = fdt_fixup_dpmac_phy_handle(fdt, + dpmac_id, phandle); + if (ret) { + fdt_del_node(fdt, subnodeoffset); + break; + } + /* calculate offset again as new node addition may have + * changed offset; + */ + offset = fdt_get_ioslot_offset(fdt, mii_dev, + fpga_offset); + phandle++; + } + + if (ret) + break; + } + + return ret; +} +#endif // CONFIG_FSL_MC_ENET +#endif + +#if defined(CONFIG_DM_ETH) && defined(CONFIG_MULTI_DTB_FIT) + +/* Structure to hold SERDES protocols supported in case of + * CONFIG_DM_ETH enabled (network interfaces are described in the DTS). + * + * @serdes_block: the index of the SERDES block + * @serdes_protocol: the decimal value of the protocol supported + * @dts_needed: DTS notes describing the current configuration are needed + * + * When dts_needed is true, the board_fit_config_name_match() function + * will try to exactly match the current configuration of the block with a DTS + * name provided. + */ +static struct serdes_configuration { + u8 serdes_block; + u32 serdes_protocol; + bool dts_needed; +} supported_protocols[] = { + /* Serdes block #1 */ + {1, 2, true}, + {1, 3, true}, + {1, 15, true}, + {1, 17, true}, + {1, 18, true}, + {1, 20, true}, + + /* Serdes block #2 */ + {2, 2, false}, + {2, 3, false}, + {2, 5, false}, + {2, 10, false}, + {2, 11, true}, + {2, 12, true}, +}; + +#define SUPPORTED_SERDES_PROTOCOLS ARRAY_SIZE(supported_protocols) + +static bool protocol_supported(u8 serdes_block, u32 protocol) +{ + struct serdes_configuration serdes_conf; + int i; + + for (i = 0; i < SUPPORTED_SERDES_PROTOCOLS; i++) { + serdes_conf = supported_protocols[i]; + if (serdes_conf.serdes_block == serdes_block && + serdes_conf.serdes_protocol == protocol) + return true; + } + + return false; +} + +static void get_str_protocol(u8 serdes_block, u32 protocol, char *str) +{ + struct serdes_configuration serdes_conf; + int i; + + for (i = 0; i < SUPPORTED_SERDES_PROTOCOLS; i++) { + serdes_conf = supported_protocols[i]; + if (serdes_conf.serdes_block == serdes_block && + serdes_conf.serdes_protocol == protocol) { + if (serdes_conf.dts_needed == true) + sprintf(str, "%u", protocol); + else + sprintf(str, "x"); + return; + } + } +} + +int board_fit_config_name_match(const char *name) +{ + struct ccsr_gur *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR); + u32 rcw_status = in_le32(&gur->rcwsr[28]); + char srds_s1_str[2], srds_s2_str[2]; + u32 srds_s1, srds_s2; + char expected_dts[100]; + + srds_s1 = rcw_status & FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_MASK; + srds_s1 >>= FSL_CHASSIS3_RCWSR28_SRDS1_PRTCL_SHIFT; + + srds_s2 = rcw_status & FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_MASK; + srds_s2 >>= FSL_CHASSIS3_RCWSR28_SRDS2_PRTCL_SHIFT; + + /* Check for supported protocols. The default DTS will be used + * in this case + */ + if (!protocol_supported(1, srds_s1) || + !protocol_supported(2, srds_s2)) + return -1; + + get_str_protocol(1, srds_s1, srds_s1_str); + get_str_protocol(2, srds_s2, srds_s2_str); + + sprintf(expected_dts, "fsl-lx2160a-qds-%s-%s", + srds_s1_str, srds_s2_str); + + if (!strcmp(name, expected_dts)) + return 0; + + return -1; +} +#endif diff --git a/board/freescale/lx2160a/lx2160a.c b/board/freescale/lx2160a/lx2160a.c index ace2a19..a5754a5 100644 --- a/board/freescale/lx2160a/lx2160a.c +++ b/board/freescale/lx2160a/lx2160a.c @@ -37,7 +37,7 @@ #include "../common/emc2305.h" #endif
-#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) #define CFG_MUX_I2C_SDHC(reg, value) ((reg & 0x3f) | value) #define SET_CFG_MUX1_SDHC1_SDHC(reg) (reg & 0x3f) #define SET_CFG_MUX2_SDHC1_SPI(reg, value) ((reg & 0xcf) | value) @@ -47,7 +47,7 @@ #define SDHC1_BASE_PMUX_DSPI 2 #define SDHC2_BASE_PMUX_DSPI 2 #define IIC5_PMUX_SPI3 3 -#endif /* CONFIG_TARGET_LX2160AQDS */ +#endif /* CONFIG_TARGET_LX2160AQDS or CONFIG_TARGET_LX2162AQDS */
DECLARE_GLOBAL_DATA_PTR;
@@ -191,7 +191,7 @@ int board_fix_fdt(void *fdt) } #endif
-#if defined(CONFIG_TARGET_LX2160AQDS) +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) void esdhc_dspi_status_fixup(void *blob) { const char esdhc0_path[] = "/soc/esdhc@2140000"; @@ -259,7 +259,7 @@ void esdhc_dspi_status_fixup(void *blob)
int esdhc_status_fixup(void *blob, const char *compat) { -#if defined(CONFIG_TARGET_LX2160AQDS) +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) /* Enable esdhc and dspi DT nodes based on RCW fields */ esdhc_dspi_status_fixup(blob); #else @@ -297,7 +297,7 @@ int checkboard(void) enum boot_src src = get_boot_src(); char buf[64]; u8 sw; -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) int clock; static const char *const freq[] = {"100", "125", "156.25", "161.13", "322.26", "", "", "", @@ -306,7 +306,7 @@ int checkboard(void) #endif
cpu_name(buf); -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) printf("Board: %s-QDS, ", buf); #else printf("Board: %s-RDB, ", buf); @@ -339,7 +339,13 @@ int checkboard(void) break; } } -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160ARDB) + printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata)); + + puts("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n"); + puts("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); + puts("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); +#else printf("FPGA: v%d (%s), build %d", (int)QIXIS_READ(scver), qixis_read_tag(buf), (int)qixis_read_minor()); @@ -350,31 +356,27 @@ int checkboard(void) sw = QIXIS_READ(brdcfg[2]); clock = sw >> 4; printf("Clock1 = %sMHz ", freq[clock]); +#if defined(CONFIG_TARGET_LX2160AQDS) clock = sw & 0x0f; printf("Clock2 = %sMHz", freq[clock]); - +#endif sw = QIXIS_READ(brdcfg[3]); puts("\nSERDES2 Reference : "); clock = sw >> 4; printf("Clock1 = %sMHz ", freq[clock]); clock = sw & 0x0f; - printf("Clock2 = %sMHz", freq[clock]); - + printf("Clock2 = %sMHz\n", freq[clock]); +#if defined(CONFIG_TARGET_LX2160AQDS) sw = QIXIS_READ(brdcfg[12]); - puts("\nSERDES3 Reference : "); + puts("SERDES3 Reference : "); clock = sw >> 4; printf("Clock1 = %sMHz Clock2 = %sMHz\n", freq[clock], freq[clock]); -#else - printf("FPGA: v%d.%d\n", QIXIS_READ(scver), QIXIS_READ(tagdata)); - - puts("SERDES1 Reference: Clock1 = 161.13MHz Clock2 = 161.13MHz\n"); - puts("SERDES2 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); - puts("SERDES3 Reference: Clock1 = 100MHz Clock2 = 100MHz\n"); +#endif #endif return 0; }
-#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) /* * implementation of CONFIG_ESDHC_DETECT_QUIRK Macro. */ @@ -562,7 +564,7 @@ int config_board_mux(void)
unsigned long get_board_sys_clk(void) { -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
switch (sysclk_conf & 0x03) { @@ -581,7 +583,7 @@ unsigned long get_board_sys_clk(void)
unsigned long get_board_ddr_clk(void) { -#ifdef CONFIG_TARGET_LX2160AQDS +#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
switch ((ddrclk_conf & 0x30) >> 4) { diff --git a/configs/lx2162aqds_tfa_SECURE_BOOT_defconfig b/configs/lx2162aqds_tfa_SECURE_BOOT_defconfig new file mode 100644 index 0000000..065f6a1 --- /dev/null +++ b/configs/lx2162aqds_tfa_SECURE_BOOT_defconfig @@ -0,0 +1,97 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2162AQDS=y +CONFIG_TFABOOT=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_NXP_ESBC=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x500000 +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_MISC_INIT_R=y +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2162a-qds" +CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x" +CONFIG_MULTI_DTB_FIT=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_ADDR=0x20500000 +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_CORTINA=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_VITESSE=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_E1000=y +CONFIG_MDIO_MUX_I2CREG=y +CONFIG_FSL_LS_MDIO=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE_RC=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_DSPI=y +CONFIG_NXP_FSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_WDT=y +CONFIG_WDT_SBSA=y +CONFIG_RSA=y +CONFIG_SPL_RSA=y +CONFIG_RSA_SOFTWARE_EXP=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_GIC_V3_ITS=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_I2C_DEFAULT_BUS_NUMBER=0 +CONFIG_DM_RTC=y +CONFIG_DM_GPIO=y +CONFIG_CMD_DATE=y +CONFIG_RTC_PCF2127=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y diff --git a/configs/lx2162aqds_tfa_defconfig b/configs/lx2162aqds_tfa_defconfig new file mode 100644 index 0000000..33ca543 --- /dev/null +++ b/configs/lx2162aqds_tfa_defconfig @@ -0,0 +1,95 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2162AQDS=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x500000 +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_TFABOOT=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_MISC_INIT_R=y +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2162a-qds" +CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x" +CONFIG_MULTI_DTB_FIT=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_ADDR=0x20500000 +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_FSL_CAAM=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_CORTINA=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_VITESSE=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_E1000=y +CONFIG_MDIO_MUX_I2CREG=y +CONFIG_FSL_LS_MDIO=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE_RC=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_DSPI=y +CONFIG_NXP_FSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_WDT=y +CONFIG_WDT_SBSA=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_GIC_V3_ITS=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_I2C_DEFAULT_BUS_NUMBER=0 +CONFIG_DM_RTC=y +CONFIG_DM_GPIO=y +CONFIG_CMD_DATE=y +CONFIG_RTC_PCF2127=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y diff --git a/configs/lx2162aqds_tfa_verified_boot_defconfig b/configs/lx2162aqds_tfa_verified_boot_defconfig new file mode 100644 index 0000000..7d0dbcd --- /dev/null +++ b/configs/lx2162aqds_tfa_verified_boot_defconfig @@ -0,0 +1,102 @@ +CONFIG_ARM=y +CONFIG_TARGET_LX2162AQDS=y +CONFIG_SYS_TEXT_BASE=0x82000000 +CONFIG_SYS_MALLOC_F_LEN=0x6000 +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x20000 +CONFIG_ENV_OFFSET=0x500000 +CONFIG_FSPI_AHB_EN_4BYTE=y +CONFIG_TFABOOT=y +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y +CONFIG_AHCI=y +CONFIG_NR_DRAM_BANKS=3 +CONFIG_FIT_VERBOSE=y +CONFIG_FIT_SIGNATURE=y +CONFIG_RSA=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_OF_STDOUT_VIA_ALIAS=y +CONFIG_BOOTDELAY=10 +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf" +# CONFIG_USE_BOOTCOMMAND is not set +CONFIG_MISC_INIT_R=y +CONFIG_BOARD_EARLY_INIT_R=y +CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_DM=y +CONFIG_CMD_GPT=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_SF=y +CONFIG_CMD_USB=y +CONFIG_CMD_WDT=y +CONFIG_CMD_CACHE=y +CONFIG_MP=y +CONFIG_OF_CONTROL=y +CONFIG_OF_BOARD_FIXUP=y +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2162a-qds" +CONFIG_OF_LIST="fsl-lx2162a-qds-17-x fsl-lx2162a-qds-18-x fsl-lx2162a-qds-20-x" +CONFIG_MULTI_DTB_FIT=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_ADDR=0x20500000 +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_DM=y +CONFIG_SATA_CEVA=y +CONFIG_FSL_CAAM=y +CONFIG_DM_MMC=y +CONFIG_FSL_ESDHC=y +CONFIG_MTD=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_SPI_FLASH_SST=y +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PHYLIB=y +CONFIG_PHY_AQUANTIA=y +CONFIG_PHY_CORTINA=y +CONFIG_PHY_REALTEK=y +CONFIG_PHY_VITESSE=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_E1000=y +CONFIG_MDIO_MUX_I2CREG=y +CONFIG_FSL_LS_MDIO=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCIE_LAYERSCAPE_RC=y +CONFIG_DM_SCSI=y +CONFIG_DM_SERIAL=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_DSPI=y +CONFIG_NXP_FSPI=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_WDT=y +CONFIG_WDT_SBSA=y +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y +CONFIG_GIC_V3_ITS=y +CONFIG_DM_I2C=y +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y +CONFIG_I2C_DEFAULT_BUS_NUMBER=0 +CONFIG_DM_RTC=y +CONFIG_DM_GPIO=y +CONFIG_CMD_DATE=y +CONFIG_RTC_PCF2127=y +CONFIG_I2C_MUX=y +CONFIG_I2C_MUX_PCA954x=y +CONFIG_TEE=y +CONFIG_OPTEE=y +CONFIG_CMD_OPTEE_RPMB=y +CONFIG_OPTEE_TA_AVB=y +CONFIG_SUPPORT_EMMC_RPMB=y diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h index 0017ac5..837760f 100644 --- a/include/configs/lx2160a_common.h +++ b/include/configs/lx2160a_common.h @@ -149,8 +149,10 @@ /* USB */ #ifdef CONFIG_USB #define CONFIG_HAS_FSL_XHCI_USB +#ifndef CONFIG_TARGET_LX2162AQDS #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #endif +#endif
/* FlexSPI */ #ifdef CONFIG_NXP_FSPI diff --git a/include/configs/lx2162aqds.h b/include/configs/lx2162aqds.h new file mode 100644 index 0000000..cb26956 --- /dev/null +++ b/include/configs/lx2162aqds.h @@ -0,0 +1,169 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 NXP + */ + +#ifndef __LX2162_QDS_H +#define __LX2162_QDS_H + +#include "lx2160a_common.h" + +/* USB */ +#undef CONFIG_USB_MAX_CONTROLLER_COUNT +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 + +/* + * Need to override existing (lx2160a) with lx2162aqds so set_board_info will + * use proper prefix when creating full board_name (SYS_BOARD + type) + */ +#undef CONFIG_SYS_BOARD +#define CONFIG_SYS_BOARD "lx2162aqds" + +#undef CONFIG_SYS_NXP_SRDS_3 + +/* Qixis */ +#define QIXIS_XMAP_MASK 0x07 +#define QIXIS_XMAP_SHIFT 5 +#define QIXIS_RST_CTL_RESET_EN 0x30 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x20 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_QSPI 0xff +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SD +#define QIXIS_LBMAP_EMMC +#define QIXIS_RCW_SRC_SD 0x08 +#define QIXIS_RCW_SRC_EMMC 0x09 +#define NON_EXTENDED_DUTCFG +#define QIXIS_SDID_MASK 0x07 +#define QIXIS_ESDHC_NO_ADAPTER 0x7 + +/* SYSCLK */ +#define QIXIS_SYSCLK_100 0x0 +#define QIXIS_SYSCLK_125 0x1 +#define QIXIS_SYSCLK_133 0x2 + +/* DDRCLK */ +#define QIXIS_DDRCLK_100 0x0 +#define QIXIS_DDRCLK_125 0x1 +#define QIXIS_DDRCLK_133 0x2 + +#define BRDCFG4_EMI1SEL_MASK 0xF8 +#define BRDCFG4_EMI1SEL_SHIFT 3 +#define BRDCFG4_EMI2SEL_MASK 0x07 +#define BRDCFG4_EMI2SEL_SHIFT 0 + +/* VID */ + +#define I2C_MUX_CH_VOL_MONITOR 0xA +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x63 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 +#define CONFIG_VID_FLS_ENV "lx2162aqds_vdd_mv" +#define CONFIG_VID + +/* The lowest and highest voltage allowed*/ +#define VDD_MV_MIN 775 +#define VDD_MV_MAX 925 + +/* PM Bus commands code for LTC3882*/ +#define PMBUS_CMD_PAGE 0x0 +#define PMBUS_CMD_READ_VOUT 0x8B +#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 +#define PMBUS_CMD_VOUT_COMMAND 0x21 +#define PWM_CHANNEL0 0x0 + +#define CONFIG_VOL_MONITOR_LTC3882_SET +#define CONFIG_VOL_MONITOR_LTC3882_READ + +/* RTC */ +#define CONFIG_SYS_RTC_BUS_NUM 0 +#define I2C_MUX_CH_RTC 0xB + +/* + * MMC + */ +#ifdef CONFIG_MMC +#ifndef __ASSEMBLY__ +u8 qixis_esdhc_detect_quirk(void); +#endif +#define CONFIG_ESDHC_DETECT_QUIRK qixis_esdhc_detect_quirk() +#endif + +/* MAC/PHY configuration */ +#if defined(CONFIG_FSL_MC_ENET) +#define CONFIG_MII +#define CONFIG_ETHPRIME "DPMAC17@rgmii-id" + +#define AQ_PHY_ADDR1 0x00 +#define AQ_PHY_ADDR2 0x01 +#define AQ_PHY_ADDR3 0x02 +#define AQ_PHY_ADDR4 0x03 + +#define CORTINA_NO_FW_UPLOAD +#define CORTINA_PHY_ADDR1 0x0 + +#define INPHI_PHY_ADDR1 0x0 +#define INPHI_PHY_ADDR2 0x1 +#ifdef CONFIG_SD_BOOT +#define IN112525_FW_ADDR 0x980000 +#else +#define IN112525_FW_ADDR 0x20980000 +#endif +#define IN112525_FW_LENGTH 0x40000 + +#define RGMII_PHY_ADDR1 0x01 +#define RGMII_PHY_ADDR2 0x02 + +#define SGMII_CARD_PORT1_PHY_ADDR 0x1C +#define SGMII_CARD_PORT2_PHY_ADDR 0x1D +#define SGMII_CARD_PORT3_PHY_ADDR 0x1E +#define SGMII_CARD_PORT4_PHY_ADDR 0x1F + +#endif + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + EXTRA_ENV_SETTINGS \ + "boot_scripts=lx2162aqds_boot.scr\0" \ + "boot_script_hdr=hdr_lx2162aqds_bs.out\0" \ + "BOARD=lx2162aqds\0" \ + "xspi_bootcmd=echo Trying load from flexspi..;" \ + "sf probe 0:0 && sf read $load_addr " \ + "$kernel_start $kernel_size ; env exists secureboot &&" \ + "sf read $kernelheader_addr_r $kernelheader_start " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + " bootm $load_addr#$BOARD\0" \ + "sd_bootcmd=echo Trying load from sd card..;" \ + "mmc dev 0; mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd ;" \ + "env exists secureboot && mmc read $kernelheader_addr_r "\ + "$kernelhdr_addr_sd $kernelhdr_size_sd " \ + " && esbc_validate ${kernelheader_addr_r};" \ + "bootm $load_addr#$BOARD\0" \ + "emmc_bootcmd=echo Trying load from emmc card..;" \ + "mmc dev 1; mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd ;" \ + "env exists secureboot && mmc read $kernelheader_addr_r "\ + "$kernelhdr_addr_sd $kernelhdr_size_sd " \ + " && esbc_validate ${kernelheader_addr_r};" \ + "bootm $load_addr#$BOARD\0" + +#include <asm/fsl_secure_boot.h> + +#endif /* __LX2162_QDS_H */