This board has been orphan for a while. (Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up the maintainership on it.
Signed-off-by: Masahiro Yamada yamada.m@jp.panasonic.com Cc: Wolfgang Denx wd@denx.de ---
board/zpc1900/Makefile | 8 -- board/zpc1900/zpc1900.c | 288 ---------------------------------------------- boards.cfg | 1 - doc/README.scrapyard | 1 + include/configs/ZPC1900.h | 261 ----------------------------------------- 5 files changed, 1 insertion(+), 558 deletions(-) delete mode 100644 board/zpc1900/Makefile delete mode 100644 board/zpc1900/zpc1900.c delete mode 100644 include/configs/ZPC1900.h
diff --git a/board/zpc1900/Makefile b/board/zpc1900/Makefile deleted file mode 100644 index e636365..0000000 --- a/board/zpc1900/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := zpc1900.o diff --git a/board/zpc1900/zpc1900.c b/board/zpc1900/zpc1900.c deleted file mode 100644 index fed4934..0000000 --- a/board/zpc1900/zpc1900.c +++ /dev/null @@ -1,288 +0,0 @@ -/* - * (C) Copyright 2001-2003 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2003-2005 Arabella Software Ltd. - * Yuli Barcohen yuli@arabellasw.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <ioports.h> -#include <mpc8260.h> -#include <miiphy.h> - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */ - /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */ - /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */ - /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */ - /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */ - /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */ - /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ - /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ - /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ - /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ - /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ - /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ - /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ - /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ - /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */ - /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */ - /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */ - /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */ - /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */ - /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */ - /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */ - /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */ - /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* SMC2 TXD */ - /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* SMC2 RXD */ - /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */ - /* PA6 */ { 0, 0, 0, 0, 0, 0 }, /* PA6 */ - /* PA5 */ { 0, 0, 0, 0, 0, 0 }, /* PA5 */ - /* PA4 */ { 0, 0, 0, 0, 0, 0 }, /* PA4 */ - /* PA3 */ { 0, 0, 0, 0, 0, 0 }, /* PA3 */ - /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */ - /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* PA1 */ - /* PA0 */ { 0, 0, 0, 0, 0, 0 } /* PA0 */ - }, - - /* Port B */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */ - /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */ - /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */ - /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */ - /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */ - /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */ - /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */ - /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */ - /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN CLSN */ - /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */ - /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */ - /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */ - /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */ - /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */ - /* PC23 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ - /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ - /* PC21 */ { 0, 0, 0, 0, 0, 0 }, /* PC21 */ - /* PC20 */ { 0, 0, 0, 0, 0, 0 }, /* PC20 */ - /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII Rx Clock (CLK13) */ - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII Tx Clock (CLK14) */ - /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */ - /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */ - /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */ - /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RENA */ - /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */ - /* PC12 */ { 0, 0, 0, 0, 0, 0 }, /* PC12 */ - /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */ - /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* LXT972 MDC */ - /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* LXT972 MDIO */ - /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* PC8 */ - /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */ - /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */ - /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */ - /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */ - /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */ - /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */ - /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */ - /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ - /* PD30 */ { 0, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ - /* PD29 */ { 0, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ - /* PD28 */ { 0, 0, 0, 0, 0, 0 }, /* PD28 */ - /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* PD27 */ - /* PD26 */ { 0, 0, 0, 0, 0, 0 }, /* PD26 */ - /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */ - /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */ - /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */ - /* PD22 */ { 0, 0, 0, 0, 0, 0 }, /* PD22 */ - /* PD21 */ { 0, 0, 0, 0, 0, 0 }, /* PD21 */ - /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD20 */ - /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */ - /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */ - /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ - /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ - /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SCL */ - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */ - /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */ - /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */ - /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -#ifdef CONFIG_SYS_NVRAM_ACCESS_ROUTINE -void *nvram_read(void *dest, long src, size_t count) -{ - return memcpy(dest, (const void *)src, count); -} - -void nvram_write(long dest, const void *src, size_t count) -{ - vu_char *p1 = (vu_char *)(CONFIG_SYS_EEPROM + 0x1555); - vu_char *p2 = (vu_char *)(CONFIG_SYS_EEPROM + 0x0AAA); - vu_char *d = (vu_char *)dest; - const uchar *s = (const uchar *)src; - - /* Unprotect the EEPROM */ - *p1 = 0xAA; - *p2 = 0x55; - *p1 = 0x80; - *p1 = 0xAA; - *p2 = 0x55; - *p1 = 0x20; - udelay(10000); - - /* Write the data to the EEPROM */ - while (count--) { - *d++ = *s++; - while (*(d - 1) != *(s - 1)) - /* wait */; - } - - /* Protect the EEPROM */ - *p1 = 0xAA; - *p2 = 0x55; - *p1 = 0xA0; - udelay(10000); -} -#endif /* CONFIG_SYS_NVRAM_ACCESS_ROUTINE */ - -phys_size_t initdram(int board_type) -{ - vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR; - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - vu_char *ramaddr; - uchar c = 0xFF; - long int msize = CONFIG_SYS_SDRAM_SIZE; - int i; - - if (bcsr[4] & BCSR_PCI_MODE) { /* PCI mode selected by JP9 */ - immap->im_clkrst.car_sccr |= SCCR_PCI_MODE; - immap->im_siu_conf.sc_siumcr = - (immap->im_siu_conf.sc_siumcr & ~SIUMCR_LBPC11) - | SIUMCR_LBPC01; - } - -#ifndef CONFIG_SYS_RAMBOOT - immap->im_siu_conf.sc_ppc_acr = 0x03; - immap->im_siu_conf.sc_ppc_alrh = 0x30126745; - immap->im_siu_conf.sc_tescr1 = 0x00004000; - - memctl->memc_mptpr = CONFIG_SYS_MPTPR; - -#ifdef CONFIG_SYS_LSDRAM_BASE - /* - Initialise local bus SDRAM only if the pins - are configured as local bus pins and not as PCI. - */ - if ((immap->im_siu_conf.sc_siumcr & SIUMCR_LBPC11) == SIUMCR_LBPC00) { - memctl->memc_lsrt = CONFIG_SYS_LSRT; - memctl->memc_or4 = CONFIG_SYS_LSDRAM_OR; - memctl->memc_br4 = CONFIG_SYS_LSDRAM_BR; - ramaddr = (vu_char *)CONFIG_SYS_LSDRAM_BASE; - memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_PREA; - *ramaddr = c; - memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) - *ramaddr = c; - memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_MRW; - *ramaddr = c; - memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_RFEN; - } -#endif /* CONFIG_SYS_LSDRAM_BASE */ - - /* Initialise 60x bus SDRAM */ - memctl->memc_psrt = CONFIG_SYS_PSRT; - memctl->memc_or2 = CONFIG_SYS_PSDRAM_OR; - memctl->memc_br2 = CONFIG_SYS_PSDRAM_BR; - /* - * The mode data for Mode Register Write command must appear on - * the address lines during a mode-set cycle. It is driven by - * the memory controller, in single PowerQUICC II mode, - * according to PSDMR[CL] and PSDMR[BL] fields. In - * 60x-compatible mode, software must drive the correct value on - * the address lines. BL=0 because for 64-bit port size burst - * length must be 4. - */ - ramaddr = (vu_char *)(CONFIG_SYS_SDRAM_BASE | - ((CONFIG_SYS_PSDMR & PSDMR_CL_MSK) << 7) | 0x10); - memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_OP_PREA; /* Precharge all banks */ - *ramaddr = c; - memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_OP_CBRR; /* CBR refresh */ - for (i = 0; i < 8; i++) - *ramaddr = c; - memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_OP_MRW; /* Mode Register write */ - *ramaddr = c; - memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_RFEN; /* Refresh enable */ - *ramaddr = c; -#endif /* CONFIG_SYS_RAMBOOT */ - - /* Return total 60x bus SDRAM size */ - return msize * 1024 * 1024; -} - -int checkboard(void) -{ - vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR; - - printf("Board: Zephyr ZPC.1900 Rev. %c\n", bcsr[2] + 0x40); - return 0; -} diff --git a/boards.cfg b/boards.cfg index f29e1df..a3f5b6e 100644 --- a/boards.cfg +++ b/boards.cfg @@ -1243,7 +1243,6 @@ Orphan powerpc mpc8260 - - ispan Orphan powerpc mpc8260 - - ispan ISPAN_REVB ISPAN:SYS_REV_B Yuli Barcohen yuli@arabellasw.com Orphan powerpc mpc8260 - - rattler Rattler - Yuli Barcohen yuli@arabellasw.com Orphan powerpc mpc8260 - - rattler Rattler8248 Rattler:MPC8248 Yuli Barcohen yuli@arabellasw.com -Orphan powerpc mpc8260 - - zpc1900 ZPC1900 - Yuli Barcohen yuli@arabellasw.com Orphan powerpc mpc83xx - freescale mpc8360erdk MPC8360ERDK - Anton Vorontsov avorontsov@ru.mvista.com Orphan powerpc mpc83xx - freescale mpc8360erdk MPC8360ERDK_33 MPC8360ERDK:CLKIN_33MHZ Anton Vorontsov avorontsov@ru.mvista.com Orphan powerpc mpc83xx - matrix_vision mergerbox MERGERBOX - Andre Schwarz andre.schwarz@matrix-vision.de diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 0a2d8fc..a042eea 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,6 +11,7 @@ easily if here is something they might want to dig for...
Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +zpc1900 powerpc mpc8260 - - Yuli Barcohen yuli@arabellasw.com mpc8260ads powerpc mpc8260 - - Yuli Barcohen yuli@arabellasw.com adder powerpc mpc8xx - - Yuli Barcohen yuli@arabellasw.com quad100hd powerpc ppc405ep - - Gary Jennejohn gljennjohn@googlemail.com diff --git a/include/configs/ZPC1900.h b/include/configs/ZPC1900.h deleted file mode 100644 index d76a140..0000000 --- a/include/configs/ZPC1900.h +++ /dev/null @@ -1,261 +0,0 @@ -/* - * Copyright (C) 2003-2005 Arabella Software Ltd. - * Yuli Barcohen yuli@arabellasw.com - * - * U-Boot configuration for Zephyr Engineering ZPC.1900 board. - * This port was developed and tested on Revision C board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_ZPC1900 1 /* ...on Zephyr ZPC.1900 board */ - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CPU_ID_STR "MPC8265" -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */ -#define CONFIG_ENV_OVERWRITE - -/* - * Select serial console configuration - * - * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - */ -#define CONFIG_CONS_ON_SMC /* Console is on SMC */ -#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ -#undef CONFIG_CONS_NONE /* It's not on external UART */ -#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */ - -/* - * Select ethernet configuration - * - * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, - * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for - * SCC, 1-3 for FCC) - * - * If CONFIG_ETHER_NONE is defined, then either the ethernet routines - * must be defined elsewhere (as for the console), or CONFIG_CMD_NET - * must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */ -#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */ -#undef CONFIG_ETHER_NONE /* No external Ethernet */ - -#ifdef CONFIG_ETHER_ON_FCC - -#define CONFIG_ETHER_INDEX 2 /* FCC2 is used for Ethernet */ - -#if (CONFIG_ETHER_INDEX == 2) -/* - * - Rx clock is CLK13 - * - Tx clock is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Full duplex - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_INDEX */ - -#define CONFIG_MII /* MII PHY management */ -#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */ -/* - * GPIO pins used for bit-banged MII communications - */ -#define MDIO_PORT 2 /* Port C */ -#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) -#define MDC_DECLARE MDIO_DECLARE - -#define MDIO_ACTIVE (iop->pdir |= 0x00400000) -#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) -#define MDIO_READ ((iop->pdat & 0x00400000) != 0) - -#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 - -#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - -#define MIIDELAY udelay(1) - -#endif /* CONFIG_ETHER_ON_FCC */ - -#ifndef CONFIG_8260_CLKIN -#define CONFIG_8260_CLKIN 66666666 /* in Hz */ -#endif - -#define CONFIG_BAUDRATE 38400 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING - - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_BOOTCOMMAND "dhcp;bootm" /* autoboot command */ -#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=:::::eth0:dhcp" - -#if defined(CONFIG_CMD_KGDB) -#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ -#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ -#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ -#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ -#endif - -#define CONFIG_BZIP2 /* include support for bzip2 compressed images */ -#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x03800000 /* 1 ... 56 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 64 - -#define CONFIG_SYS_IMMR 0xF0000000 -#define CONFIG_SYS_LSDRAM_BASE 0xFC000000 -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_BCSR 0xFEA00000 -#define CONFIG_SYS_EEPROM 0xFEB00000 -#define CONFIG_SYS_FLSIMM_BASE 0xFF000000 - -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE } - -#define BCSR_PCI_MODE 0x01 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Hard reset configuration word */ -#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM | HRCW_BPS01| HRCW_CIP |\ - HRCW_L2CPC10 | HRCW_DPPC00 | HRCW_ISB100 |\ - HRCW_BMS | HRCW_LBPC00 | HRCW_APPC10 |\ - HRCW_MODCK_H0111 \ - ) /* 0x16848207 */ -/* No slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM) -#define CONFIG_ENV_IS_IN_NVRAM 1 -#endif - -#ifdef CONFIG_ENV_IS_IN_FLASH -# define CONFIG_ENV_SECT_SIZE 0x10000 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#else -# define CONFIG_ENV_ADDR (CONFIG_SYS_EEPROM + 0x400) -# define CONFIG_ENV_SIZE 0x1000 -# define CONFIG_SYS_NVRAM_ACCESS_ROUTINE -#endif - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#define CONFIG_SYS_HID0_INIT (HID0_ICFI) -#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) - -#define CONFIG_SYS_HID2 0 - -#define CONFIG_SYS_SIUMCR 0x42200000 -#define CONFIG_SYS_SYPCR 0xFFFFFFC3 -#define CONFIG_SYS_BCR 0x90000000 -#define CONFIG_SYS_SCCR SCCR_DFBRG01 - -#define CONFIG_SYS_RMR RMR_CSRE -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) -#define CONFIG_SYS_RCCR 0 - -#define CONFIG_SYS_PSDMR /* 0x834DA43B */0x014DA43A -#define CONFIG_SYS_PSRT 0x0F/* 0x0C */ -#define CONFIG_SYS_LSDMR 0x0085A562 -#define CONFIG_SYS_LSRT 0x0F -#define CONFIG_SYS_MPTPR 0x4000 - -#define CONFIG_SYS_PSDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00000041) -#define CONFIG_SYS_PSDRAM_OR 0xFC0028C0 -#define CONFIG_SYS_LSDRAM_BR (CONFIG_SYS_LSDRAM_BASE | 0x00001861) -#define CONFIG_SYS_LSDRAM_OR 0xFF803480 - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00000801) -#define CONFIG_SYS_OR0_PRELIM 0xFFE00856 -#define CONFIG_SYS_BR5_PRELIM (CONFIG_SYS_EEPROM | 0x00000801) -#define CONFIG_SYS_OR5_PRELIM 0xFFFF03F6 -#define CONFIG_SYS_BR6_PRELIM (CONFIG_SYS_FLSIMM_BASE | 0x00001801) -#define CONFIG_SYS_OR6_PRELIM 0xFF000856 -#define CONFIG_SYS_BR7_PRELIM (CONFIG_SYS_BCSR | 0x00000801) -#define CONFIG_SYS_OR7_PRELIM 0xFFFF83F6 - -#define CONFIG_SYS_RESET_ADDRESS 0xC0000000 - -#endif /* __CONFIG_H */