Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers.
BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class).
Signed-off-by: Alexandru Gagniuc alex.g@adaptrum.com --- drivers/net/Kconfig | 28 ++------------- drivers/net/phy/Kconfig | 90 +++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 92 insertions(+), 26 deletions(-) create mode 100644 drivers/net/phy/Kconfig
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index f52629f..93bc787 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1,3 +1,5 @@ +source "drivers/net/phy/Kconfig" + config DM_ETH bool "Enable Driver Model for Ethernet drivers" depends on DM @@ -8,32 +10,6 @@ config DM_ETH This is currently implemented in net/eth.c Look in include/net.h for details.
-config PHYLIB - bool "Ethernet PHY (physical media interface) support" - help - Enable Ethernet PHY (physical media interface) support. - -config RTL8211X_PHY_FORCE_MASTER - bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode" - depends on PHYLIB - help - Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F). - This can work around link stability and data corruption issues on gigabit - links which can occur in slave mode on certain PHYs, e.g. on the - RTL8211C(L). - - Please note that two directly connected devices (i.e. via crossover cable) - will not be able to establish a link between each other if they both force - master mode. Multiple devices forcing master mode when connected by a - network switch do not pose a problem as the switch configures its affected - ports into slave mode. - - This option only affects gigabit links. If you must establish a direct - connection between two devices which both force master mode, try forcing - the link speed to 100MBit/s. - - If unsure, say N. - menuconfig NETDEVICES bool "Network device support" depends on NET diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig new file mode 100644 index 0000000..52529f2 --- /dev/null +++ b/drivers/net/phy/Kconfig @@ -0,0 +1,90 @@ + +config BITBANGMII + bool "Bit-banged ethernet MII management channel support" + +config MV88E6352_SWITCH + bool "Marvell 88E6352 switch support" + +menuconfig PHYLIB + bool "Ethernet PHY (physical media interface) support" + help + Enable Ethernet PHY (physical media interface) support. + +if PHYLIB + +config MV88E61XX_SWITCH + bool "Marvel MV88E61xx Ethernet switch PHY support." + +config PHYLIB_10G + bool "Generic 10G PHY support" + +config PHY_AQUANTIA + bool "Aquantia Ethernet PHYs support" + +config PHY_ATHEROS + bool "Atheros Ethernet PHYs support" + +config PHY_BROADCOM + bool "Broadcom Ethernet PHYs support" + +config PHY_CORTINA + bool "Cortina Ethernet PHYs support" + +config PHY_DAVICOM + bool "Davicom Ethernet PHYs support" + +config PHY_ET1011C + bool "LSI TruePHY ET1011C support" + +config PHY_LXT + bool "LXT971 Ethernet PHY support" + +config PHY_MARVELL + bool "Marvell Ethernet PHYs support" + +config PHY_MICREL + bool "Micrel Ethernet PHYs support" + +config PHY_NATSEMI + bool "National Semiconductor Ethernet PHYs support" + +config PHY_REALTEK + bool "Realtek Ethernet PHYs support" + +config RTL8211X_PHY_FORCE_MASTER + bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode" + depends on PHY_REALTEK + help + Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F). + This can work around link stability and data corruption issues on gigabit + links which can occur in slave mode on certain PHYs, e.g. on the + RTL8211C(L). + + Please note that two directly connected devices (i.e. via crossover cable) + will not be able to establish a link between each other if they both force + master mode. Multiple devices forcing master mode when connected by a + network switch do not pose a problem as the switch configures its affected + ports into slave mode. + + This option only affects gigabit links. If you must establish a direct + connection between two devices which both force master mode, try forcing + the link speed to 100MBit/s. + + If unsure, say N. + +config PHY_SMSC + bool "Microchip(SMSC) Ethernet PHYs support" + +config PHY_TERANETICS + bool "Teranetics Ethernet PHYs support" + +config PHY_TI + bool "Texas Instruments Ethernet PHYs support" + +config PHY_VITESSE + bool "Vitesse Ethernet PHYs support" + +config PHY_XILINX + bool "Xilinx Ethernet PHYs support" + +endif #PHYLIB