On 4/19/21 4:37 PM, Ilko Iliev wrote:
This patch remove the network support for PM9261 because currently there is no DM suport for Davicom D9000.
Signed-off-by: Ilko Iliev iliev@ronetix.at
Hi,
If I look at the commit message, I would expect something is enabled, but in fact something is removed. Could you update the short commit subject according to what you are doing in the commit itself ?
Also, if you are removing the dm9000, why do you still enable the DM_ETH ? what is it used for ?
Eugen
Changes for v2:
- add Signed-off-by
board/ronetix/pm9261/pm9261.c | 54 ----------------------------------- configs/pm9261_defconfig | 1 + include/configs/pm9261.h | 9 ------ 3 files changed, 1 insertion(+), 63 deletions(-)
diff --git a/board/ronetix/pm9261/pm9261.c b/board/ronetix/pm9261/pm9261.c index 5be2c5e192..fe52c7c176 100644 --- a/board/ronetix/pm9261/pm9261.c +++ b/board/ronetix/pm9261/pm9261.c @@ -20,10 +20,6 @@ #include <asm/arch/at91_matrix.h> #include <asm/arch/clk.h> #include <asm/arch/gpio.h> -#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_DRIVER_DM9000) -#include <net.h> -#endif -#include <netdev.h> #include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR; @@ -80,36 +76,6 @@ static void pm9261_nand_hw_init(void) } #endif
-#ifdef CONFIG_DRIVER_DM9000 -static void pm9261_dm9000_hw_init(void) -{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;/* Configure SMC CS2 for DM9000 */writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),&smc->cs[2].setup);writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(8) |AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(8),&smc->cs[2].pulse);writel(AT91_SMC_CYCLE_NWE(16) | AT91_SMC_CYCLE_NRD(16),&smc->cs[2].cycle);writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |AT91_SMC_MODE_EXNW_DISABLE |AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |AT91_SMC_MODE_TDF_CYCLE(1),&smc->cs[2].mode);/* Configure Interrupt pin as input, no pull-up */at91_periph_clk_enable(ATMEL_ID_PIOA);at91_set_pio_input(AT91_PIO_PORTA, 24, 0);-} -#endif
- int board_early_init_f(void) { return 0;
@@ -132,13 +98,6 @@ int board_init(void) return 0; }
-#ifdef CONFIG_DRIVER_DM9000 -int board_eth_init(struct bd_info *bis) -{
return dm9000_initialize(bis);-} -#endif
- int dram_init(void) { /* dram_init must store complete ramsize in gd->ram_size */
@@ -155,19 +114,6 @@ int dram_init_banksize(void) return 0; }
-#ifdef CONFIG_RESET_PHY_R -void reset_phy(void) -{ -#ifdef CONFIG_DRIVER_DM9000
/** Initialize ethernet HW addr prior to starting Linux,* needed for nfsroot*/eth_init();-#endif -} -#endif
- #ifdef CONFIG_DISPLAY_BOARDINFO int checkboard (void) {
diff --git a/configs/pm9261_defconfig b/configs/pm9261_defconfig index e0a2ae18c6..774039e8bc 100644 --- a/configs/pm9261_defconfig +++ b/configs/pm9261_defconfig @@ -50,6 +50,7 @@ CONFIG_NAND_ATMEL=y CONFIG_DM_SPI_FLASH=y CONFIG_SPI_FLASH_ATMEL=y CONFIG_SPI_FLASH_DATAFLASH=y +CONFIG_DM_ETH=y CONFIG_PINCTRL=y CONFIG_PINCTRL_AT91=y CONFIG_DM_SERIAL=y diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h index 2cc47d1237..382d19a241 100644 --- a/include/configs/pm9261.h +++ b/include/configs/pm9261.h @@ -173,15 +173,6 @@ #define CONFIG_SYS_MAX_FLASH_SECT 256 #define CONFIG_SYS_MAX_FLASH_BANKS 1
-/* Ethernet */ -#define CONFIG_DRIVER_DM9000 1 -#define CONFIG_DM9000_BASE 0x30000000 -#define DM9000_IO CONFIG_DM9000_BASE -#define DM9000_DATA (CONFIG_DM9000_BASE + 4) -#define CONFIG_DM9000_USE_16BIT 1 -#define CONFIG_NET_RETRY_COUNT 20 -#define CONFIG_RESET_PHY_R 1
- /* USB */ #define CONFIG_USB_ATMEL #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
-- 2.25.1