From: Sonic Zhang sonic.zhang@analog.com
- Disable NAND driver on bf537-stamp. - Make MMC_SPI optional. - Disable LCD driver on bf527-ezkit. - Enlarge BF609 nor flash reserved size from 256k to 512k bytes.
Signed-off-by: Sonic Zhang sonic.zhang@analog.com Signed-off-by: Sonic Zhang sonic.adi@gmail.com --- include/configs/bf527-ezkit.h | 12 ++++++------ include/configs/bf537-stamp.h | 10 ++++++---- include/configs/bf609-ezkit.h | 2 ++ 3 files changed, 14 insertions(+), 10 deletions(-)
diff --git a/include/configs/bf527-ezkit.h b/include/configs/bf527-ezkit.h index 7b51b53..db1b613 100644 --- a/include/configs/bf527-ezkit.h +++ b/include/configs/bf527-ezkit.h @@ -149,10 +149,15 @@ #define CONFIG_MUSB_TIMEOUT 100000 #endif
+/* Don't waste time transferring a logo over the UART */ +#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) +/*# define CONFIG_VIDEO*/ +#endif
/* * Video Settings */ +#ifdef CONFIG_VIDEO #ifdef CONFIG_BF527_EZKIT_REV_2_1 # define CONFIG_LQ035Q1_SPI_BUS 0 # define CONFIG_LQ035Q1_SPI_CS 7 @@ -166,7 +171,7 @@ #else # define EASYLOGO_HEADER <asm/bfin_logo_230x230_lzma.h> #endif - +#endif /* CONFIG_VIDEO */
/* * Misc Settings @@ -175,11 +180,6 @@ #define CONFIG_RTC_BFIN #define CONFIG_UART_CONSOLE 1
-/* Don't waste time transferring a logo over the UART */ -#if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) -# define CONFIG_VIDEO -#endif -
/* * Pull in common ADI header for remaining command/environment setup diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h index 05029d4..25cebf8 100644 --- a/include/configs/bf537-stamp.h +++ b/include/configs/bf537-stamp.h @@ -52,7 +52,7 @@ #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MONITOR_LEN (768 * 1024) #define CONFIG_SYS_MALLOC_LEN (384 * 1024)
@@ -135,15 +135,17 @@ /* * SPI_MMC Settings */ +#define CONFIG_MMC_SPI +#ifdef CONFIG_MMC_SPI #define CONFIG_MMC #define CONFIG_GENERIC_MMC -#define CONFIG_MMC_SPI - +#endif
/* * NAND Settings */ /* #define CONFIG_NAND_PLAT */ +#ifdef CONFIG_NAND_PLAT #define CONFIG_SYS_NAND_BASE 0x20212000 #define CONFIG_SYS_MAX_NAND_DEVICE 1
@@ -158,7 +160,7 @@ #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) #define NAND_PLAT_GPIO_DEV_READY GPIO_PF3 - +#endif /* CONFIG_NAND_PLAT */
/* * CF-CARD IDE-HDD Support diff --git a/include/configs/bf609-ezkit.h b/include/configs/bf609-ezkit.h index f0ac86b..e7b02a5 100644 --- a/include/configs/bf609-ezkit.h +++ b/include/configs/bf609-ezkit.h @@ -156,6 +156,8 @@ #undef CONFIG_UART_CONSOLE_IS_JTAG #endif
+#define CONFIG_BOARD_SIZE_LIMIT $$((512 * 1024)) + /* * Run core 1 from L1 SRAM start address when init uboot on core 0 */