To simplify drivers/Makefile a bit when using TPL/SPL, we consistently use the $(SPL_TPL_) macro to test for drivers that have separate configuration symbols for the full U-boot, SPL and TPL stages. Instead of explicitly repeating them in two separate if-guarded sections of the Makefile, we can now simply list these options once.
Signed-off-by: Philipp Tomsich philipp.tomsich@theobroma-systems.com
Reviewed-by: Simon Glass sjg@chromium.org Reviewed-by: Tom Rini trini@konsulko.com ---
Changes in v3: None Changes in v2: None
drivers/Makefile | 36 ++++++++++++++++-------------------- 1 file changed, 16 insertions(+), 20 deletions(-)
diff --git a/drivers/Makefile b/drivers/Makefile index 8624bd8..b98550e 100644 --- a/drivers/Makefile +++ b/drivers/Makefile @@ -2,33 +2,34 @@ # SPDX-License-Identifier: GPL-2.0+ #
-obj-$(CONFIG_$(SPL_TPL_)DM) += core/ -obj-$(CONFIG_$(SPL_)CLK) += clk/ -obj-$(CONFIG_$(SPL_)LED) += led/ -obj-$(CONFIG_$(SPL_)PHY) += phy/ -obj-$(CONFIG_$(SPL_)PINCTRL) += pinctrl/ -obj-$(CONFIG_$(SPL_)RAM) += ram/ +obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/ +obj-$(CONFIG_$(SPL_TPL_)DM) += core/ +obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/ +obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/ +obj-$(CONFIG_$(SPL_TPL_)LED) += led/ +obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/ +obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/ +obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/ +obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/ +obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/ +obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/ +obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/ +obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/
+ifndef CONFIG_TPL_BUILD ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/ obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/ -obj-$(CONFIG_SPL_I2C_SUPPORT) += i2c/ obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/ -obj-$(CONFIG_SPL_MMC_SUPPORT) += mmc/ obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/ obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/ obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/ obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/ -obj-$(CONFIG_SPL_SERIAL_SUPPORT) += serial/ -obj-$(CONFIG_SPL_SPI_SUPPORT) += spi/ obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/ obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/ -obj-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/ obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/ -obj-$(CONFIG_SPL_NAND_SUPPORT) += mtd/nand/ obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/ -obj-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += mtd/spi/ obj-$(CONFIG_SPL_UBI) += mtd/ubispl/ obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/ @@ -48,18 +49,13 @@ obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/ obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/ obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/ obj-$(CONFIG_SPL_MMC_SUPPORT) += block/ + +endif endif
ifdef CONFIG_TPL_BUILD
-obj-$(CONFIG_TPL_I2C_SUPPORT) += i2c/ -obj-$(CONFIG_TPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/ -obj-$(CONFIG_TPL_MMC_SUPPORT) += mmc/ obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/ -obj-$(CONFIG_TPL_NAND_SUPPORT) += mtd/nand/ -obj-$(CONFIG_TPL_SERIAL_SUPPORT) += serial/ -obj-$(CONFIG_TPL_SPI_FLASH_SUPPORT) += mtd/spi/ -obj-$(CONFIG_TPL_SPI_SUPPORT) += spi/
endif