Both U-boot and Linux kernel have grown over the last releases and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy christophe.leroy@csgroup.eu Reviewed-by: FRANJOU Stephane stephane.franjou@csgroup.eu --- board/cssi/mcr3000/mcr3000.env | 16 ++++++++-------- configs/MCR3000_defconfig | 10 +++++++--- include/configs/mcr3000.h | 4 ++-- 3 files changed, 17 insertions(+), 13 deletions(-)
diff --git a/board/cssi/mcr3000/mcr3000.env b/board/cssi/mcr3000/mcr3000.env index 542d90e3ae..372ab09094 100644 --- a/board/cssi/mcr3000/mcr3000.env +++ b/board/cssi/mcr3000/mcr3000.env @@ -2,13 +2,13 @@
sdram_type=SDRAM flash_type=AM29LV160DB -loadaddr=0x400000 -filename=uImage.lzma -nfsroot=/opt/ofs +loadaddr=0x1200000 +filename=mcr3000.itb dhcp_ip=ip=:::::eth0:dhcp console_args=console=ttyCPM0,115200N8 -flashboot=setenv bootargs ${console_args} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:mcr3k:eth0:off;${ofl_args}; bootm 0x04060000 - 0x04050000 -tftpboot=setenv bootargs ${console_args} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:mcr3k:eth0:off ${ofl_args}; tftp ${loadaddr} ${filename};tftp 0xf00000 mcr3000.dtb;bootm ${loadaddr} - 0xf00000 -netboot=dhcp ${loadaddr} ${filename};tftp 0xf00000 mcr3000.dtb;setenv bootargs root=/dev/nfs rw ${console_args} ${dhcp_ip};bootm ${loadaddr} - 0xf00000 -nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${nfsroot} ${console_args} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:mcr3k:eth0:off;bootm 0x04060000 - 0x04050000 -dhcpboot=dhcp ${loadaddr} ${filename};tftp 0xf00000 mcr3000.dtb;setenv bootargs ${console_args} ${dhcp_ip} ${ofl_args}; bootm ${loadaddr} - 0xf00000 +loadkernel=ubi part nand0;ubifsmount ubi0;ubifsload ${loadaddr} /boot/${filename};ubifsumount; ubi detach +bootcmd=run flashboot +flashboot=setenv bootargs ${console_args} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:mcr3k:eth0:off;${ofl_args}; run loadkernel; bootm ${loadaddr} +tftpboot=setenv bootargs ${console_args} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:mcr3k:eth0:off ${ofl_args}; tftp ${loadaddr} ${filename}; bootm ${loadaddr} +dhcpboot=dhcp ${loadaddr} ${filename};setenv bootargs ${console_args} ${dhcp_ip} ${ofl_args}; bootm ${loadaddr} +update=echo 'Updating ubi image'; if tftp 0x2000 $ubifile; then nand erase.chip; nand write 0x2000 0x00 $filesize; fi diff --git a/configs/MCR3000_defconfig b/configs/MCR3000_defconfig index 3e16ffc2ef..f96e9f06e1 100644 --- a/configs/MCR3000_defconfig +++ b/configs/MCR3000_defconfig @@ -20,6 +20,7 @@ CONFIG_SYS_SCCR=0x00C20000 CONFIG_SYS_SCCR_MASK=0x60000000 CONFIG_SYS_DER=0x2002000F CONFIG_SYS_MONITOR_LEN=327680 +CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_MONITOR_BASE=0x04000000 CONFIG_BOOTDELAY=5 @@ -36,11 +37,12 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PBSIZE=278 # CONFIG_CMD_BDI is not set # CONFIG_CMD_CONSOLE is not set -CONFIG_SYS_BOOTM_LEN=0x800000 +CONFIG_SYS_BOOTM_LEN=0x2000000 # CONFIG_CMD_IMI is not set CONFIG_CMD_ASKENV=y # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set +CONFIG_CMD_MTD=y CONFIG_CMD_NAND=y # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set @@ -51,6 +53,8 @@ CONFIG_CMD_MII=y CONFIG_MII_INIT=y CONFIG_CMD_PING=y # CONFIG_CMD_SLEEP is not set +CONFIG_CMD_MTDPARTS=y +CONFIG_CMD_UBI=y CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_FLASH=y @@ -58,7 +62,7 @@ CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_USE_IPADDR=y CONFIG_IPADDR="192.168.0.3" CONFIG_USE_NETMASK=y -CONFIG_NETMASK="255.0.0.0" +CONFIG_NETMASK="255.255.255.0" CONFIG_USE_SERVERIP=y CONFIG_SERVERIP="192.168.0.1" CONFIG_SYS_BR0_PRELIM_BOOL=y @@ -87,6 +91,7 @@ CONFIG_SYS_BR7_PRELIM=0x1C000001 CONFIG_SYS_OR7_PRELIM=0xFFFF810A # CONFIG_MMC is not set CONFIG_MTD=y +CONFIG_DM_MTD=y CONFIG_MTD_NOR_FLASH=y CONFIG_FLASH_CFI_DRIVER=y CONFIG_FLASH_SHOW_PROGRESS=0 @@ -97,5 +102,4 @@ CONFIG_MPC8XX_FEC=y # CONFIG_PCI is not set CONFIG_DM_SERIAL=y CONFIG_WDT=y -CONFIG_SHA256=y CONFIG_LZMA=y diff --git a/include/configs/mcr3000.h b/include/configs/mcr3000.h index 8d78fd362a..6b16b050ff 100644 --- a/include/configs/mcr3000.h +++ b/include/configs/mcr3000.h @@ -23,10 +23,10 @@
/* * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is + * have to be in the first 32 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_SYS_BOOTMAPSZ (8 << 20) +#define CFG_SYS_BOOTMAPSZ (32 << 20)
/* Environment Configuration */