GPIOs should be requested before use. Without this, driver model will not permit the GPIO to be used.
Signed-off-by: Simon Glass sjg@chromium.org ---
arch/arm/imx-common/i2c-mxv7.c | 14 ++++++++++++++ board/compulab/cm_fx6/cm_fx6.c | 9 +++++++++ board/compulab/cm_fx6/common.c | 3 +++ 3 files changed, 26 insertions(+)
diff --git a/arch/arm/imx-common/i2c-mxv7.c b/arch/arm/imx-common/i2c-mxv7.c index a580873..7cea024 100644 --- a/arch/arm/imx-common/i2c-mxv7.c +++ b/arch/arm/imx-common/i2c-mxv7.c @@ -4,6 +4,7 @@ * SPDX-License-Identifier: GPL-2.0+ */ #include <common.h> +#include <malloc.h> #include <asm/arch/clock.h> #include <asm/arch/imx-regs.h> #include <asm/errno.h> @@ -72,8 +73,21 @@ static void * const i2c_bases[] = { void setup_i2c(unsigned i2c_index, int speed, int slave_addr, struct i2c_pads_info *p) { + char *name; + if (i2c_index >= ARRAY_SIZE(i2c_bases)) return; + + name = malloc(9); + assert(name); + sprintf(name, "i2c_sda%d", i2c_index); + gpio_request(p->sda.gp, name); + + name = malloc(9); + assert(name); + sprintf(name, "i2c_scl%d", i2c_index); + gpio_request(p->scl.gp, name); + /* Enable i2c clock */ enable_i2c_clk(1, i2c_index); /* Make sure bus is idle */ diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c index fdb8ebf..80a123d 100644 --- a/board/compulab/cm_fx6/cm_fx6.c +++ b/board/compulab/cm_fx6/cm_fx6.c @@ -71,8 +71,15 @@ static iomux_v3_cfg_t const sata_pads[] = {
static void cm_fx6_setup_issd(void) { + int i; + SETUP_IOMUX_PADS(sata_pads); + + for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) + gpio_request(cm_fx6_issd_gpios[i], "sata"); + /* Make sure this gpio has logical 0 value */ + gpio_request(CM_FX6_SATA_PWLOSS_INT, "sata_pwloss_int"); gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0); udelay(100);
@@ -167,6 +174,7 @@ static int cm_fx6_usb_hub_reset(void) }
SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL)); + gpio_request(CM_FX6_USB_HUB_RST, "usb_hub_rst"); gpio_direction_output(CM_FX6_USB_HUB_RST, 0); udelay(10); gpio_direction_output(CM_FX6_USB_HUB_RST, 1); @@ -324,6 +332,7 @@ int board_eth_init(bd_t *bis)
SETUP_IOMUX_PADS(enet_pads); /* phy reset */ + gpio_request(CM_FX6_ENET_NRST, "enet_nrst"); gpio_direction_output(CM_FX6_ENET_NRST, 0); udelay(500); gpio_set_value(CM_FX6_ENET_NRST, 1); diff --git a/board/compulab/cm_fx6/common.c b/board/compulab/cm_fx6/common.c index 1f39679..562313b 100644 --- a/board/compulab/cm_fx6/common.c +++ b/board/compulab/cm_fx6/common.c @@ -79,6 +79,9 @@ void cm_fx6_set_ecspi_iomux(void)
int board_spi_cs_gpio(unsigned bus, unsigned cs) { +#ifndef CONFIG_SPL_BUILD + gpio_request(CM_FX6_ECSPI_BUS0_CS0, "ecspi_bus0_cs0"); +#endif return (bus == 0 && cs == 0) ? (CM_FX6_ECSPI_BUS0_CS0) : -1; } #endif