Schneider HMIBSC board dts has already been reviewed upstream on the linux-arm-msm mailing list. So once it comes through the Linux kernel release cycle into the U-Boot dts/upstream subtree, a switch to OF_UPSTREAM can be made. For the time being maintain the U-Boot copy.
Link: https://lore.kernel.org/linux-kernel/20240403043416.3800259-4-sumit.garg@lin... Signed-off-by: Sumit Garg sumit.garg@linaro.org --- arch/arm/dts/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++++++ 1 file changed, 491 insertions(+) create mode 100644 arch/arm/dts/apq8016-schneider-hmibsc.dts
diff --git a/arch/arm/dts/apq8016-schneider-hmibsc.dts b/arch/arm/dts/apq8016-schneider-hmibsc.dts new file mode 100644 index 00000000000..75c6137e5a1 --- /dev/null +++ b/arch/arm/dts/apq8016-schneider-hmibsc.dts @@ -0,0 +1,491 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2015, The Linux Foundation. All rights reserved. + * Copyright (c) 2024, Linaro Ltd. + */ + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> +#include <dt-bindings/sound/apq8016-lpass.h> + +/ { + model = "Schneider Electric HMIBSC Board"; + compatible = "schneider,apq8016-hmibsc", "qcom,apq8016"; + + aliases { + i2c1 = &blsp_i2c6; + i2c3 = &blsp_i2c4; + i2c4 = &blsp_i2c3; + mmc0 = &sdhc_1; /* eMMC */ + mmc1 = &sdhc_2; /* SD card */ + serial0 = &blsp_uart1; + serial1 = &blsp_uart2; + spi0 = &blsp_spi5; + usid0 = &pm8916_0; + }; + + chosen { + stdout-path = "serial0"; + }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7533_out>; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + pinctrl-0 = <&msm_key_volp_n_default>; + pinctrl-names = "default"; + + button { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pm8916_mpps_leds>; + pinctrl-names = "default"; + + led-1 { + function = LED_FUNCTION_WLAN; + color = <LED_COLOR_ID_YELLOW>; + gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; + default-state = "off"; + }; + + led-2 { + function = LED_FUNCTION_BLUETOOTH; + color = <LED_COLOR_ID_BLUE>; + gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + default-state = "off"; + }; + }; + + memory@80000000 { + reg = <0 0x80000000 0 0x40000000>; + }; + + reserved-memory { + ramoops@bff00000 { + compatible = "ramoops"; + reg = <0x0 0xbff00000 0x0 0x100000>; + record-size = <0x20000>; + console-size = <0x20000>; + ftrace-size = <0x20000>; + ecc-size = <16>; + }; + }; + + usb-hub { + compatible = "smsc,usb3503"; + reset-gpios = <&pm8916_gpios 1 GPIO_ACTIVE_LOW>; + initial-mode = <1>; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&usb_id_default>; + pinctrl-names = "default"; + }; +}; + +&blsp_i2c3 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + }; +}; + +&blsp_i2c4 { + status = "okay"; + + adv_bridge: bridge@39 { + compatible = "adi,adv7533"; + reg = <0x39>; + interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; + + adi,dsi-lanes = <4>; + clocks = <&rpmcc RPM_SMD_BB_CLK2>; + clock-names = "cec"; + pd-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; + + avdd-supply = <&pm8916_l6>; + a2vdd-supply = <&pm8916_l6>; + dvdd-supply = <&pm8916_l6>; + pvdd-supply = <&pm8916_l6>; + v1p2-supply = <&pm8916_l6>; + v3p3-supply = <&pm8916_l17>; + + pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>; + pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>; + pinctrl-names = "default","sleep"; + #sound-dai-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7533_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7533_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; +}; + +&blsp_i2c6 { + status = "okay"; + + rtc@30 { + compatible = "sii,s35390a"; + reg = <0x30>; + }; + + eeprom@50 { + compatible = "atmel,24c256"; + reg = <0x50>; + }; +}; + +&blsp_spi5 { + cs-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + status = "okay"; + + tpm@0 { + compatible = "infineon,slb9670", "tcg,tpm_tis-spi"; + reg = <0>; + spi-max-frequency = <500000>; + }; +}; + +&blsp_uart1 { + label = "UART0"; + status = "okay"; +}; + +&blsp_uart2 { + label = "UART1"; + status = "okay"; +}; + +&lpass { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0_out { + data-lanes = <0 1 2 3>; + remote-endpoint = <&adv7533_in>; +}; + +&pm8916_codec { + qcom,mbhc-vthreshold-low = <75 150 237 450 500>; + qcom,mbhc-vthreshold-high = <75 150 237 450 500>; + status = "okay"; +}; + +&pm8916_gpios { + gpio-line-names = + "USB_HUB_RESET_N_PM", + "USB_SW_SEL_PM", + "NC", + "NC"; + + usb_hub_reset_pm: usb-hub-reset-pm-state { + pins = "gpio1"; + function = PMIC_GPIO_FUNC_NORMAL; + input-disable; + output-high; + }; + + usb_hub_reset_pm_device: usb-hub-reset-pm-device-state { + pins = "gpio1"; + function = PMIC_GPIO_FUNC_NORMAL; + input-disable; + output-low; + }; + + usb_sw_sel_pm: usb-sw-sel-pm-state { + pins = "gpio2"; + function = PMIC_GPIO_FUNC_NORMAL; + power-source = <PM8916_GPIO_VPH>; + input-disable; + output-high; + }; + + usb_sw_sel_pm_device: usb-sw-sel-pm-device-state { + pins = "gpio2"; + function = PMIC_GPIO_FUNC_NORMAL; + power-source = <PM8916_GPIO_VPH>; + input-disable; + output-low; + }; +}; + +&pm8916_mpps { + gpio-line-names = + "NC", + "WLAN_LED_CTRL", + "BT_LED_CTRL", + "NC"; + + pm8916_mpps_leds: pm8916-mpps-state { + pins = "mpp2", "mpp3"; + function = "digital"; + output-low; + }; +}; + +&pm8916_resin { + linux,code = <KEY_POWER>; + status = "okay"; +}; + +&pm8916_rpm_regulators { + pm8916_l17: l17 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&sdhc_1 { + status = "okay"; +}; + +&sdhc_2 { + pinctrl-0 = <&sdc2_default &sdc2_cd_default>; + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; + pinctrl-names = "default", "sleep"; + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&sound { + pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>; + pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>; + pinctrl-names = "default", "sleep"; + model = "HMIBSC"; + audio-routing = + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + status = "okay"; + + quaternary-dai-link { + link-name = "ADV7533"; + cpu { + sound-dai = <&lpass MI2S_QUATERNARY>; + }; + codec { + sound-dai = <&adv_bridge 0>; + }; + }; + + primary-dai-link { + link-name = "WCD"; + cpu { + sound-dai = <&lpass MI2S_PRIMARY>; + }; + codec { + sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>; + }; + }; + + tertiary-dai-link { + link-name = "WCD-Capture"; + cpu { + sound-dai = <&lpass MI2S_TERTIARY>; + }; + codec { + sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>; + }; + }; +}; + +&tlmm { + pinctrl-0 = <&uart1_mux0_rs232_high &uart1_mux1_rs232_low>; + pinctrl-names = "default"; + + adv7533_int_active: adv533-int-active-state { + pins = "gpio31"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + adv7533_int_suspend: adv7533-int-suspend-state { + pins = "gpio31"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + adv7533_switch_active: adv7533-switch-active-state { + pins = "gpio32"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + adv7533_switch_suspend: adv7533-switch-suspend-state { + pins = "gpio32"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + msm_key_volp_n_default: msm-key-volp-n-default-state { + pins = "gpio107"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + sdc2_cd_default: sdc2-cd-default-state { + pins = "gpio38"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + /* + * UART1 being the debug console supports various modes of + * operation (RS-232/485/422) controlled via GPIOs configured + * mux as follows: + * + * gpio100 gpio99 UART mode + * 0 0 loopback + * 0 1 RS-232 + * 1 0 RS-485 + * 1 1 RS-422 + * + * The default mode configured here is RS-232 mode. + */ + uart1_mux0_rs232_high: uart1-mux0-rs232-state { + bootph-all; + pins = "gpio99"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-high; + }; + + uart1_mux1_rs232_low: uart1-mux1-rs232-state { + bootph-all; + pins = "gpio100"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; + + usb_id_default: usb-id-default-state { + pins = "gpio110"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; +}; + +&usb { + extcon = <&usb_id>, <&usb_id>; + pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>; + pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>; + pinctrl-names = "default", "device"; + status = "okay"; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&wcnss { + firmware-name = "qcom/apq8016/wcnss.mbn"; + status = "okay"; +}; + +&wcnss_ctrl { + firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin"; +}; + +&wcnss_iris { + compatible = "qcom,wcn3620"; +}; + +&wcnss_mem { + status = "okay"; +}; + +/* PINCTRL - additions to nodes defined in msm8916.dtsi */ + +/* + * 2mA drive strength is not enough when connecting multiple + * I2C devices with different pull up resistors. + */ +&blsp_i2c4_default { + drive-strength = <16>; +}; + +&blsp_i2c6_default { + drive-strength = <16>; +}; + +&blsp_uart1_default { + bootph-all; +}; + +/* Enable CoreSight */ +&cti0 { status = "okay"; }; +&cti1 { status = "okay"; }; +&cti12 { status = "okay"; }; +&cti13 { status = "okay"; }; +&cti14 { status = "okay"; }; +&cti15 { status = "okay"; }; +&debug0 { status = "okay"; }; +&debug1 { status = "okay"; }; +&debug2 { status = "okay"; }; +&debug3 { status = "okay"; }; +&etf { status = "okay"; }; +&etm0 { status = "okay"; }; +&etm1 { status = "okay"; }; +&etm2 { status = "okay"; }; +&etm3 { status = "okay"; }; +&etr { status = "okay"; }; +&funnel0 { status = "okay"; }; +&funnel1 { status = "okay"; }; +&replicator { status = "okay"; }; +&stm { status = "okay"; }; +&tpiu { status = "okay"; };