Migrate the following options to CONFIG_DM: CONFIG_DM_GPIO CONFIG_DM_MMC CONFIG_DM_ETH CONFIG_DM_SERIAL CONFIG_DM_USB
Signed-off-by: Ilko Iliev iliev@ronetix.at --- board/ronetix/pm9g45/pm9g45.c | 8 +- configs/pm9g45_defconfig | 44 +++++++-- include/configs/pm9g45.h | 173 ++++++++++++++++++---------------- 3 files changed, 132 insertions(+), 93 deletions(-)
diff --git a/board/ronetix/pm9g45/pm9g45.c b/board/ronetix/pm9g45/pm9g45.c index 17e520a9e9..871db4abea 100644 --- a/board/ronetix/pm9g45/pm9g45.c +++ b/board/ronetix/pm9g45/pm9g45.c @@ -139,15 +139,15 @@ int board_init(void) int dram_init(void) { /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size((void *)PHYS_SDRAM, - PHYS_SDRAM_SIZE); + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + CONFIG_SYS_SDRAM_SIZE); return 0; }
int dram_init_banksize(void) { - gd->bd->bi_dram[0].start = PHYS_SDRAM; - gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE; + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; + gd->bd->bi_dram[0].size = CONFIG_SYS_SDRAM_SIZE;
return 0; } diff --git a/configs/pm9g45_defconfig b/configs/pm9g45_defconfig index 928e446c3f..c3f7e1408d 100644 --- a/configs/pm9g45_defconfig +++ b/configs/pm9g45_defconfig @@ -2,27 +2,57 @@ CONFIG_ARM=y CONFIG_ARCH_AT91=y CONFIG_SYS_TEXT_BASE=0x73f00000 CONFIG_TARGET_PM9G45=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_DEBUG_UART_BOARD_INIT=y +CONFIG_DEBUG_UART_BASE=0xffffee00 +CONFIG_DEBUG_UART_CLOCK=132000000 +CONFIG_DEBUG_UART=y CONFIG_NR_DRAM_BANKS=1 -CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G45" +CONFIG_NAND_BOOT=y CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTARGS=y CONFIG_BOOTARGS="fbcon=rotate:3 console=tty0 console=ttyS0,115200 root=/dev/mtdblock4 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,1664k(env),2M(linux)ro,-(root) rw rootfstype=jffs2" -# CONFIG_DISPLAY_CPUINFO is not set +# CONFIG_CONSOLE_MUX is not set +CONFIG_SYS_CONSOLE_IS_IN_ENV=y # CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot> " +# CONFIG_CMD_BDI is not set +CONFIG_CMD_BOOTZ=y +# CONFIG_CMD_IMI is not set # CONFIG_CMD_FLASH is not set +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y CONFIG_CMD_NAND=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y CONFIG_CMD_PING=y -CONFIG_CMD_CACHE=y -CONFIG_CMD_JFFS2=y +CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y +CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek" CONFIG_ENV_IS_IN_NAND=y -# CONFIG_MMC is not set -CONFIG_NAND=y +CONFIG_DM=y +CONFIG_CLK=y +CONFIG_CLK_AT91=y +CONFIG_DM_GPIO=y +CONFIG_AT91_GPIO=y +CONFIG_DM_MMC=y +CONFIG_GENERIC_ATMEL_MCI=y CONFIG_NAND_ATMEL=y +CONFIG_DM_ETH=y +CONFIG_MACB=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_AT91=y +CONFIG_DM_SERIAL=y +CONFIG_DEBUG_UART_ATMEL=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_ATMEL_USART=y +CONFIG_TIMER=y +CONFIG_ATMEL_PIT_TIMER=y CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_STORAGE=y diff --git a/include/configs/pm9g45.h b/include/configs/pm9g45.h index 46b8030894..e34873cea7 100644 --- a/include/configs/pm9g45.h +++ b/include/configs/pm9g45.h @@ -15,110 +15,119 @@ #ifndef __CONFIG_H #define __CONFIG_H
-/* - * SoC must be defined first, before hardware.h is included. - * In this case SoC is defined in boards.cfg. - */ -#include <asm/hardware.h> - -#define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9G45" - -#define CONFIG_MACH_TYPE MACH_TYPE_PM9G45 - /* ARM asynchronous clock */ -#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ -#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ - -#define CONFIG_ARCH_CPU_INIT - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG #define CONFIG_SKIP_LOWLEVEL_INIT
-/* - * Hardware drivers - */ -#define CONFIG_AT91_GPIO 1 -#define CONFIG_ATMEL_USART 1 -#define CONFIG_USART_BASE ATMEL_BASE_DBGU -#define CONFIG_USART_ID ATMEL_ID_SYS - -#define CONFIG_SYS_USE_NANDFLASH 1 - -/* LED */ -#define CONFIG_AT91_LED -#define CONFIG_RED_LED GPIO_PIN_PD(31) /* this is the user1 led */ -#define CONFIG_GREEN_LED GPIO_PIN_PD(0) /* this is the user2 led */ - +/* general purpose I/O */ +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/* * BOOTP options */ -#define CONFIG_BOOTP_BOOTFILESIZE 1 - -#define CONFIG_JFFS2_CMDLINE 1 -#define CONFIG_JFFS2_NAND 1 -#define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */ -#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ -#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */ +#define CONFIG_BOOTP_BOOTFILESIZE
/* SDRAM */ -#define PHYS_SDRAM 0x70000000 -#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */ +#define CONFIG_SYS_SDRAM_BASE 0x70000000 +#define CONFIG_SYS_SDRAM_SIZE 0x08000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* NAND flash */ #ifdef CONFIG_CMD_NAND -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x40000000 -#define CONFIG_SYS_NAND_DBW_8 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 /* our ALE is AD21 */ -#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +#define CONFIG_SYS_NAND_MASK_ALE BIT(21) /* our CLE is AD22 */ -#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) -#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(3) - +#define CONFIG_SYS_NAND_MASK_CLE BIT(22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD3 +#define CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT #endif
/* Ethernet */ -#define CONFIG_MACB 1 -#define CONFIG_RMII 1 -#define CONFIG_NET_RETRY_COUNT 20 -#define CONFIG_RESET_PHY_R 1 - -/* USB */ -#define CONFIG_USB_ATMEL -#define CONFIG_USB_ATMEL_CLK_SEL_UPLL -#define CONFIG_USB_OHCI_NEW 1 -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */ -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 - -/* board specific(not enough SRAM) */ -#define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000 - -#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */ - -#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM -#define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE - -/* bootstrap + u-boot + env + linux in nandflash */ -#define CONFIG_ENV_OFFSET 0x60000 -#define CONFIG_ENV_OFFSET_REDUND 0x80000 -#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ -#define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm" +#define CONFIG_RESET_PHY_R +#define CONFIG_AT91_WANTS_COMMON_PHY + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END 0x23e00000 + +#ifdef CONFIG_NAND_BOOT +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_OFFSET 0x140000 +#define CONFIG_ENV_OFFSET_REDUND 0x100000 +#define CONFIG_ENV_SIZE 0x20000 + +#define CONFIG_BOOTCOMMAND \ + "nand read 0x70000000 0x200000 0x300000;" \ + "bootm 0x70000000" +#elif CONFIG_SD_BOOT +/* bootstrap + u-boot + env + linux in mmc */ +#define CONFIG_ENV_SIZE 0x4000 + +#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x71000000 dtb; " \ + "fatload mmc 0:1 0x72000000 zImage; " \ + "bootz 0x72000000 - 0x71000000" +#endif
/* * Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\ - 0x1000) +#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \ + 128 * 1024, 0x1000) + +/* Defines for SPL */ +#define CONFIG_SPL_TEXT_BASE 0x300000 +#define CONFIG_SPL_MAX_SIZE 0x010000 +#define CONFIG_SPL_STACK 0x310000 + +#define CONFIG_SYS_MONITOR_LEN 0x80000 + +#ifdef CONFIG_SD_BOOT + +#define CONFIG_SPL_BSS_START_ADDR 0x70000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000 +#define CONFIG_SYS_SPL_MALLOC_START 0x70080000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000 + +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 +#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" + +#elif CONFIG_NAND_BOOT +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_NAND_SOFTECC +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE + +#define CONFIG_SYS_NAND_PAGE_SIZE 0x800 +#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCSIZE 256 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \ + 48, 49, 50, 51, 52, 53, 54, 55, \ + 56, 57, 58, 59, 60, 61, 62, 63, } +#endif
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \ - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SPL_ATMEL_SIZE +#define CONFIG_SYS_MASTER_CLOCK 132096000 +#define CONFIG_SYS_AT91_PLLA 0x20c73f03 +#define CONFIG_SYS_MCKR 0x1301 +#define CONFIG_SYS_MCKR_CSS 0x1302
#endif