Drop this old code which is not built anymore, as it depends on CONFIG_VIDEO which has been removed.
Signed-off-by: Simon Glass sjg@chromium.org ---
board/siemens/common/board.c | 3 - board/siemens/common/factoryset.c | 7 - board/siemens/common/factoryset.h | 3 - board/siemens/pxm2/board.c | 189 ----------------------- board/siemens/rut/board.c | 247 ------------------------------ 5 files changed, 449 deletions(-)
diff --git a/board/siemens/common/board.c b/board/siemens/common/board.c index 56283660d37..85025f20efa 100644 --- a/board/siemens/common/board.c +++ b/board/siemens/common/board.c @@ -96,9 +96,6 @@ int board_init(void) #ifdef CONFIG_NAND_CS_INIT board_nand_cs_init(); #endif -#ifdef CONFIG_VIDEO - board_video_init(); -#endif
return 0; } diff --git a/board/siemens/common/factoryset.c b/board/siemens/common/factoryset.c index fba678b4260..4e36a6f3199 100644 --- a/board/siemens/common/factoryset.c +++ b/board/siemens/common/factoryset.c @@ -275,13 +275,6 @@ int factoryset_read_eeprom(int i2c_addr) } printf("DFU USB: VID = 0x%4x, PID = 0x%4x\n", factory_dat.usb_vendor_id, factory_dat.usb_product_id); -#endif -#if defined(CONFIG_VIDEO) - if (0 <= get_factory_record_val(cp, size, (uchar *)"DISP1", - (uchar *)"name", factory_dat.disp_name, - MAX_STRING_LENGTH)) { - debug("display name: %s\n", factory_dat.disp_name); - } #endif if (0 <= get_factory_record_val(cp, size, (uchar *)"DEV", (uchar *)"num", factory_dat.serial, diff --git a/board/siemens/common/factoryset.h b/board/siemens/common/factoryset.h index 261a2176879..8fa6c3b3d3b 100644 --- a/board/siemens/common/factoryset.h +++ b/board/siemens/common/factoryset.h @@ -17,9 +17,6 @@ struct factorysetcontainer { int usb_vendor_id; int usb_product_id; int pxm50; -#if defined(CONFIG_VIDEO) - unsigned char disp_name[MAX_STRING_LENGTH]; -#endif unsigned char serial[MAX_STRING_LENGTH]; int version; uchar asn[MAX_STRING_LENGTH]; diff --git a/board/siemens/pxm2/board.c b/board/siemens/pxm2/board.c index de52838d771..47f19bcb8fd 100644 --- a/board/siemens/pxm2/board.c +++ b/board/siemens/pxm2/board.c @@ -28,7 +28,6 @@ #include <asm/arch/gpio.h> #include <asm/arch/mmc_host_def.h> #include <asm/arch/sys_proto.h> -#include "../../../drivers/video/da8xx-fb.h" #include <asm/io.h> #include <asm/emif.h> #include <asm/gpio.h> @@ -243,194 +242,6 @@ int board_eth_init(struct bd_info *bis) } #endif /* #if defined(CONFIG_DRIVER_TI_CPSW) */
-#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) -static struct da8xx_panel lcd_panels[] = { - /* AUO G156XW01 V1 */ - [0] = { - .name = "AUO_G156XW01_V1", - .width = 1376, - .height = 768, - .hfp = 14, - .hbp = 64, - .hsw = 56, - .vfp = 1, - .vbp = 28, - .vsw = 3, - .pxl_clk = 60000000, - .invert_pxl_clk = 0, - }, - /* AUO B101EVN06 V0 */ - [1] = { - .name = "AUO_B101EVN06_V0", - .width = 1280, - .height = 800, - .hfp = 52, - .hbp = 84, - .hsw = 36, - .vfp = 3, - .vbp = 14, - .vsw = 6, - .pxl_clk = 60000000, - .invert_pxl_clk = 0, - }, - /* - * Settings from factoryset - * stored in EEPROM - */ - [2] = { - .name = "factoryset", - .width = 0, - .height = 0, - .hfp = 0, - .hbp = 0, - .hsw = 0, - .vfp = 0, - .vbp = 0, - .vsw = 0, - .pxl_clk = 60000000, - .invert_pxl_clk = 0, - }, -}; - -static const struct display_panel disp_panel = { - WVGA, - 32, - 16, - COLOR_ACTIVE, -}; - -static const struct lcd_ctrl_config lcd_cfg = { - &disp_panel, - .ac_bias = 255, - .ac_bias_intrpt = 0, - .dma_burst_sz = 16, - .bpp = 32, - .fdd = 0x80, - .tft_alt_mode = 0, - .stn_565_mode = 0, - .mono_8bit_mode = 0, - .invert_line_clock = 1, - .invert_frm_clock = 1, - .sync_edge = 0, - .sync_ctrl = 1, - .raster_order = 0, -}; - -static int set_gpio(int gpio, int state) -{ - gpio_request(gpio, "temp"); - gpio_direction_output(gpio, state); - gpio_set_value(gpio, state); - gpio_free(gpio); - return 0; -} - -static int enable_backlight(void) -{ - set_gpio(BOARD_LCD_POWER, 1); - set_gpio(BOARD_BACK_LIGHT, 1); - set_gpio(BOARD_TOUCH_POWER, 1); - return 0; -} - -static int enable_pwm(void) -{ - struct pwmss_regs *pwmss = (struct pwmss_regs *)PWMSS0_BASE; - struct pwmss_ecap_regs *ecap; - int ticks = PWM_TICKS; - int duty = PWM_DUTY; - - ecap = (struct pwmss_ecap_regs *)AM33XX_ECAP0_BASE; - /* enable clock */ - setbits_le32(&pwmss->clkconfig, ECAP_CLK_EN); - /* TimeStam Counter register */ - writel(0xdb9, &ecap->tsctr); - /* config period */ - writel(ticks - 1, &ecap->cap3); - writel(ticks - 1, &ecap->cap1); - setbits_le16(&ecap->ecctl2, - (ECTRL2_MDSL_ECAP | ECTRL2_SYNCOSEL_MASK | 0xd0)); - /* config duty */ - writel(duty, &ecap->cap2); - writel(duty, &ecap->cap4); - /* start */ - setbits_le16(&ecap->ecctl2, ECTRL2_CTRSTP_FREERUN); - return 0; -} - -static struct dpll_regs dpll_lcd_regs = { - .cm_clkmode_dpll = CM_WKUP + 0x98, - .cm_idlest_dpll = CM_WKUP + 0x48, - .cm_clksel_dpll = CM_WKUP + 0x54, -}; - -/* no console on this board */ -int board_cfb_skip(void) -{ - return 1; -} - -#define PLL_GET_M(v) ((v >> 8) & 0x7ff) -#define PLL_GET_N(v) (v & 0x7f) - -static int get_clk(struct dpll_regs *dpll_regs) -{ - unsigned int val; - unsigned int m, n; - int f = 0; - - val = readl(dpll_regs->cm_clksel_dpll); - m = PLL_GET_M(val); - n = PLL_GET_N(val); - f = (m * V_OSCK) / n; - - return f; -}; - -int clk_get(int clk) -{ - return get_clk(&dpll_lcd_regs); -}; - -static int conf_disp_pll(int m, int n) -{ - struct cm_perpll *cmper = (struct cm_perpll *)CM_PER; - struct cm_dpll *cmdpll = (struct cm_dpll *)CM_DPLL; - struct dpll_params dpll_lcd = {m, n, -1, -1, -1, -1, -1}; - - u32 *const clk_domains[] = { - &cmper->lcdclkctrl, - 0 - }; - u32 *const clk_modules_explicit_en[] = { - &cmper->lcdclkctrl, - &cmper->lcdcclkstctrl, - &cmper->epwmss0clkctrl, - 0 - }; - do_enable_clocks(clk_domains, clk_modules_explicit_en, 1); - writel(0x0, &cmdpll->clklcdcpixelclk); - - do_setup_dpll(&dpll_lcd_regs, &dpll_lcd); - - return 0; -} - -static int board_video_init(void) -{ - conf_disp_pll(24, 1); - if (factory_dat.pxm50) - da8xx_video_init(&lcd_panels[0], &lcd_cfg, lcd_cfg.bpp); - else - da8xx_video_init(&lcd_panels[1], &lcd_cfg, lcd_cfg.bpp); - - enable_pwm(); - enable_backlight(); - - return 0; -} -#endif - #ifdef CONFIG_BOARD_LATE_INIT int board_late_init(void) { diff --git a/board/siemens/rut/board.c b/board/siemens/rut/board.c index e0f232d3b80..a8b196a65c9 100644 --- a/board/siemens/rut/board.c +++ b/board/siemens/rut/board.c @@ -37,7 +37,6 @@ #include <linux/delay.h> #include "board.h" #include "../common/factoryset.h" -#include "../../../drivers/video/da8xx-fb.h"
/* * Read header information from EEPROM into global structure. @@ -224,252 +223,6 @@ void hw_watchdog_init(void) } #endif /* defined(CONFIG_HW_WATCHDOG) */
-#if defined(CONFIG_VIDEO) && !defined(CONFIG_SPL_BUILD) -static struct da8xx_panel lcd_panels[] = { - /* FORMIKE, 4.3", 480x800, KWH043MC17-F01 */ - [0] = { - .name = "KWH043MC17-F01", - .width = 480, - .height = 800, - .hfp = 50, /* no spec, "don't care" values */ - .hbp = 50, - .hsw = 50, - .vfp = 50, - .vbp = 50, - .vsw = 50, - .pxl_clk = 35910000, /* tCYCD=20ns, max 50MHz, 60fps */ - .invert_pxl_clk = 1, - }, - /* FORMIKE, 4.3", 480x800, KWH043ST20-F01 */ - [1] = { - .name = "KWH043ST20-F01", - .width = 480, - .height = 800, - .hfp = 50, /* no spec, "don't care" values */ - .hbp = 50, - .hsw = 50, - .vfp = 50, - .vbp = 50, - .vsw = 50, - .pxl_clk = 35910000, /* tCYCD=20ns, max 50MHz, 60fps */ - .invert_pxl_clk = 1, - }, - /* Multi-Inno, 4.3", 480x800, MI0430VT-1 */ - [2] = { - .name = "MI0430VT-1", - .width = 480, - .height = 800, - .hfp = 50, /* no spec, "don't care" values */ - .hbp = 50, - .hsw = 50, - .vfp = 50, - .vbp = 50, - .vsw = 50, - .pxl_clk = 35910000, /* tCYCD=20ns, max 50MHz, 60fps */ - .invert_pxl_clk = 1, - }, -}; - -static const struct display_panel disp_panels[] = { - [0] = { - WVGA, - 16, /* RGB 888 */ - 16, - COLOR_ACTIVE, - }, - [1] = { - WVGA, - 16, /* RGB 888 */ - 16, - COLOR_ACTIVE, - }, - [2] = { - WVGA, - 24, /* RGB 888 */ - 16, - COLOR_ACTIVE, - }, -}; - -static const struct lcd_ctrl_config lcd_cfgs[] = { - [0] = { - &disp_panels[0], - .ac_bias = 255, - .ac_bias_intrpt = 0, - .dma_burst_sz = 16, - .bpp = 16, - .fdd = 0x80, - .tft_alt_mode = 0, - .stn_565_mode = 0, - .mono_8bit_mode = 0, - .invert_line_clock = 1, - .invert_frm_clock = 1, - .sync_edge = 0, - .sync_ctrl = 1, - .raster_order = 0, - }, - [1] = { - &disp_panels[1], - .ac_bias = 255, - .ac_bias_intrpt = 0, - .dma_burst_sz = 16, - .bpp = 16, - .fdd = 0x80, - .tft_alt_mode = 0, - .stn_565_mode = 0, - .mono_8bit_mode = 0, - .invert_line_clock = 1, - .invert_frm_clock = 1, - .sync_edge = 0, - .sync_ctrl = 1, - .raster_order = 0, - }, - [2] = { - &disp_panels[2], - .ac_bias = 255, - .ac_bias_intrpt = 0, - .dma_burst_sz = 16, - .bpp = 24, - .fdd = 0x80, - .tft_alt_mode = 0, - .stn_565_mode = 0, - .mono_8bit_mode = 0, - .invert_line_clock = 1, - .invert_frm_clock = 1, - .sync_edge = 0, - .sync_ctrl = 1, - .raster_order = 0, - }, - -}; - -/* no console on this board */ -int board_cfb_skip(void) -{ - return 1; -} - -#define PLL_GET_M(v) ((v >> 8) & 0x7ff) -#define PLL_GET_N(v) (v & 0x7f) - -static struct dpll_regs dpll_lcd_regs = { - .cm_clkmode_dpll = CM_WKUP + 0x98, - .cm_idlest_dpll = CM_WKUP + 0x48, - .cm_clksel_dpll = CM_WKUP + 0x54, -}; - -static int get_clk(struct dpll_regs *dpll_regs) -{ - unsigned int val; - unsigned int m, n; - int f = 0; - - val = readl(dpll_regs->cm_clksel_dpll); - m = PLL_GET_M(val); - n = PLL_GET_N(val); - f = (m * V_OSCK) / n; - - return f; -}; - -int clk_get(int clk) -{ - return get_clk(&dpll_lcd_regs); -}; - -static int conf_disp_pll(int m, int n) -{ - struct cm_perpll *cmper = (struct cm_perpll *)CM_PER; - struct dpll_params dpll_lcd = {m, n, -1, -1, -1, -1, -1}; -#if defined(DISPL_PLL_SPREAD_SPECTRUM) - struct cm_wkuppll *cmwkup = (struct cm_wkuppll *)CM_WKUP; -#endif - - u32 *const clk_domains[] = { - &cmper->lcdclkctrl, - 0 - }; - u32 *const clk_modules_explicit_en[] = { - &cmper->lcdclkctrl, - &cmper->lcdcclkstctrl, - &cmper->spi1clkctrl, - 0 - }; - do_enable_clocks(clk_domains, clk_modules_explicit_en, 1); - - do_setup_dpll(&dpll_lcd_regs, &dpll_lcd); - -#if defined(DISPL_PLL_SPREAD_SPECTRUM) - writel(0x64, &cmwkup->resv6[3]); /* 0x50 */ - writel(0x800, &cmwkup->resv6[2]); /* 0x4c */ - writel(readl(&cmwkup->clkmoddplldisp) | CM_CLKMODE_DPLL_SSC_EN_MASK, - &cmwkup->clkmoddplldisp); /* 0x98 */ -#endif - return 0; -} - -static int set_gpio(int gpio, int state) -{ - gpio_request(gpio, "temp"); - gpio_direction_output(gpio, state); - gpio_set_value(gpio, state); - gpio_free(gpio); - return 0; -} - -static int enable_lcd(void) -{ - unsigned char buf[1]; - - set_gpio(BOARD_LCD_RESET, 0); - mdelay(1); - set_gpio(BOARD_LCD_RESET, 1); - mdelay(1); - - /* spi lcd init */ - kwh043st20_f01_spi_startup(1, 0, 5000000, SPI_MODE_0); - - /* backlight on */ - buf[0] = 0xf; - i2c_write(0x24, 0x7, 1, buf, 1); - buf[0] = 0x3f; - i2c_write(0x24, 0x8, 1, buf, 1); - return 0; -} - -int arch_early_init_r(void) -{ - enable_lcd(); - return 0; -} - -static int board_video_init(void) -{ - int i; - int anzdisp = ARRAY_SIZE(lcd_panels); - int display = 1; - - for (i = 0; i < anzdisp; i++) { - if (strncmp((const char *)factory_dat.disp_name, - lcd_panels[i].name, - strlen((const char *)factory_dat.disp_name)) == 0) { - printf("DISPLAY: %s\n", factory_dat.disp_name); - break; - } - } - if (i == anzdisp) { - i = 1; - printf("%s: %s not found, using default %s\n", __func__, - factory_dat.disp_name, lcd_panels[i].name); - } - conf_disp_pll(24, 1); - da8xx_video_init(&lcd_panels[display], &lcd_cfgs[display], - lcd_cfgs[display].bpp); - - return 0; -} -#endif /* ifdef CONFIG_VIDEO */ - #ifdef CONFIG_BOARD_LATE_INIT int board_late_init(void) {