February 2024 - U-Boot

[PATCH v2] arm: sunxi: Reduce inrush current on Olimex A20-OLinuXino_MICRO configs
by Philippe Coval 12 Feb '24

12 Feb '24

This change fix reboot, both configurations were tested on my Olimex A20 Micro Rev E with debian-12. This issue was also present and fixed on A20 Lime2 (in 8311e84b18), quoting Olliver Schinagl: The lime2 features a too large capacitor on the LDO3 output, which causes the PMIC to shutdown when enabling power. To be able to still boot up however, we must gradually enable power on LDO3 for this board. We do this by enabling both the inrush quirk and the maximum slope the AXP209 supports. Link: https://bugs.debian.org/1060752 Cc: Olliver Schinagl <oliver(a)schinagl.nl> Cc: Priit Laes <plaes(a)plaes.org> Cc: Maxime Ripard <maxime.ripard(a)bootlin.com> Signed-off-by: Philippe Coval <rzr(a)users.sf.net> --- Changes in v2: - Add qirk to eMMC configuration of same machine configs/A20-OLinuXino_MICRO-eMMC_defconfig | 1 + configs/A20-OLinuXino_MICRO_defconfig | 1 + 2 files changed, 2 insertions(+) diff --git a/configs/A20-OLinuXino_MICRO-eMMC_defconfig b/configs/A20-OLinuXino_MICRO-eMMC_defconfig index ca5869f43d..2f26b0ca01 100644 --- a/configs/A20-OLinuXino_MICRO-eMMC_defconfig +++ b/configs/A20-OLinuXino_MICRO-eMMC_defconfig @@ -20,6 +20,7 @@ CONFIG_ETH_DESIGNWARE=y CONFIG_MII=y CONFIG_SUN7I_GMAC=y CONFIG_SUN7I_GMAC_FORCE_TXERR=y +CONFIG_AXP_ALDO3_INRUSH_QUIRK=y CONFIG_AXP_ALDO3_VOLT=2800 CONFIG_AXP_ALDO4_VOLT=2800 CONFIG_SCSI=y diff --git a/configs/A20-OLinuXino_MICRO_defconfig b/configs/A20-OLinuXino_MICRO_defconfig index db4270f9b2..673ab85c8a 100644 --- a/configs/A20-OLinuXino_MICRO_defconfig +++ b/configs/A20-OLinuXino_MICRO_defconfig @@ -20,6 +20,7 @@ CONFIG_ETH_DESIGNWARE=y CONFIG_MII=y CONFIG_SUN7I_GMAC=y CONFIG_SUN7I_GMAC_FORCE_TXERR=y +CONFIG_AXP_ALDO3_INRUSH_QUIRK=y CONFIG_AXP_ALDO3_VOLT=2800 CONFIG_AXP_ALDO4_VOLT=2800 CONFIG_SCSI=y -- 2.43.0

2 1

[PATCH RFC] sunxi: pinephone: detect existed magnetometer and fixup dtb
by Andrey Skvortsov 12 Feb '24

12 Feb '24

In newer 1.2 PinePhone board revisions LIS3MDL magnetometer was replaced by AF8133J. They use the same PB1 pin in different modes. LIS3MDL uses it as an gpio input to handle interrupt. AF8133J uses it as an gpio output as a reset signal. It wasn't possible at runtime to enable both device tree nodes and detect supported sensor at probe time. AF8133J has reset pin (PB1) connected to the SoC. By default AF8133J is in a reset state and don't respond to probe request on I2C bus. Extra code would be needed to handle reset signal. Therefore this code uses LIS3MDL magnetometer instead of AF8133J. Introducing new dts 1.2b with AF8133J sensor would require probing in SPL. That would lead to pulling in into SPL I2C controller driver, RSB controller driver, introducing new AXP803 driver to power-up sensors for probe. It's working, but SPL is pretty size-constrained on A64 and doesn't have much space. Therefore fdt fixup is done in U-Boot proper without introducing new board revision and new dts. Signed-off-by: Andrey Skvortsov <andrej.skvortzov(a)gmail.com> --- AF8133J's driver isn't upstreamed yet, but it will be soon. Therefore this is RFC patch. I'd like to know whether selected approach will be accepted in u-boot before submiting coresponding dts changes to the Linux kernel. Any feedback on this change would be very welcome. board/sunxi/board.c | 26 ++++++++++++++++++++++++++ configs/pinephone_defconfig | 1 + 2 files changed, 27 insertions(+) diff --git a/board/sunxi/board.c b/board/sunxi/board.c index 1305302060..a4bfa24400 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -15,6 +15,7 @@ #include <dm.h> #include <env.h> #include <hang.h> +#include <i2c.h> #include <image.h> #include <init.h> #include <log.h> @@ -920,6 +921,28 @@ static void bluetooth_dt_fixup(void *blob) "local-bd-address", bdaddr, ETH_ALEN, 1); } +#ifdef CONFIG_PINEPHONE_DT_SELECTION + +#define PINEPHONE_LIS3MDL_I2C_ADDR 0x1E +#define PINEPHONE_LIS3MDL_I2C_BUS 1 /* I2C1 */ + +static void board_dt_fixup(void *blob) +{ + struct udevice *bus, *dev; + + if (!fdt_node_check_compatible(blob, 0, "pine64,pinephone-1.2")) + if (!uclass_get_device_by_seq(UCLASS_I2C, PINEPHONE_LIS3MDL_I2C_BUS, &bus)) { + dm_i2c_probe(bus, PINEPHONE_LIS3MDL_I2C_ADDR, 0, &dev); + fdt_set_status_by_compatible( + blob, "st,lis3mdl-magn", + dev ? FDT_STATUS_OKAY : FDT_STATUS_DISABLED); + fdt_set_status_by_compatible( + blob, "voltafield,af8133j", + dev ? FDT_STATUS_DISABLED : FDT_STATUS_OKAY); + } +} +#endif + int ft_board_setup(void *blob, struct bd_info *bd) { int __maybe_unused r; @@ -934,6 +957,9 @@ int ft_board_setup(void *blob, struct bd_info *bd) bluetooth_dt_fixup(blob); +#ifdef CONFIG_PINEPHONE_DT_SELECTION + board_dt_fixup(blob); +#endif #ifdef CONFIG_VIDEO_DT_SIMPLEFB r = sunxi_simplefb_setup(blob); if (r) diff --git a/configs/pinephone_defconfig b/configs/pinephone_defconfig index eebc676901..457e7ee1e7 100644 --- a/configs/pinephone_defconfig +++ b/configs/pinephone_defconfig @@ -12,6 +12,7 @@ CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_PINEPHONE_DT_SELECTION=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_OF_LIST="sun50i-a64-pinephone-1.1 sun50i-a64-pinephone-1.2" +CONFIG_SYS_I2C_MVTWSI=y CONFIG_LED_STATUS=y CONFIG_LED_STATUS_GPIO=y CONFIG_LED_STATUS0=y -- 2.43.0

2 3

[PULL] u-boot-sh/master-779h0-r2
by Marek Vasut 11 Feb '24

11 Feb '24

The following changes since commit d7aaaf4223d0a2f9f8c9eed47d7431860b3116d8: Merge tag 'u-boot-dfu-20240209' of https://source.denx.de/u-boot/custodians/u-boot-dfu (2024-02-09 09:00:42 -0500) are available in the Git repository at: https://source.denx.de/u-boot/custodians/u-boot-sh.git master-779h0-r2 for you to fetch changes up to 53066deccbedf02439309b0d4aca9f0be853a8da: ARM: renesas: Add Renesas R8A779H0 V4M Gray Hawk board code (2024-02-10 17:08:06 +0100) ---------------------------------------------------------------- Duy Nguyen (2): dt-bindings: clock: Add R8A779H0 V4M CPG Core Clock Definitions dt-bindings: power: Add R8A779H0 V4M SYSC power domain definitions Hai Pham (8): clk: renesas: Add R8A779H0 V4M clock tables pinctrl: renesas: Add R8A779H0 V4M PFC tables ARM: renesas: Add R8A779H0 V4M Kconfig entry and PRR ID mtd: spi: renesas: Add R8A779H0 V4M support ARM: dts: renesas: Add Renesas R8A779H0 V4M SoC support ARM: dts: renesas: Add Renesas R8A779H0 V4M DT extras ARM: dts: renesas: Add Renesas Gray Hawk boards support ARM: renesas: Add Renesas R8A779H0 V4M Gray Hawk board code Marek Vasut (1): clk: renesas: Implement R8A779H0 V4M PLL7 support arch/arm/dts/Makefile | 3 +- arch/arm/dts/r8a779h0-gray-hawk-cpu.dtsi | 166 + arch/arm/dts/r8a779h0-gray-hawk-csi-dsi.dtsi | 15 + arch/arm/dts/r8a779h0-gray-hawk-ethernet.dtsi | 15 + arch/arm/dts/r8a779h0-gray-hawk-u-boot.dts | 42 + arch/arm/dts/r8a779h0-gray-hawk.dts | 25 + arch/arm/dts/r8a779h0-u-boot.dtsi | 27 + arch/arm/dts/r8a779h0.dtsi | 460 +++ arch/arm/mach-rmobile/Kconfig.rcar4 | 13 + arch/arm/mach-rmobile/cpu_info.c | 1 + arch/arm/mach-rmobile/include/mach/rmobile.h | 1 + board/renesas/grayhawk/Kconfig | 15 + board/renesas/grayhawk/MAINTAINERS | 5 + board/renesas/grayhawk/Makefile | 9 + board/renesas/grayhawk/grayhawk.c | 66 + configs/r8a779h0_grayhawk_defconfig | 75 + drivers/clk/renesas/Kconfig | 6 + drivers/clk/renesas/Makefile | 1 + drivers/clk/renesas/clk-rcar-gen3.c | 6 + drivers/clk/renesas/r8a779h0-cpg-mssr.c | 293 ++ drivers/clk/renesas/rcar-gen3-cpg.h | 3 + drivers/pinctrl/renesas/Kconfig | 6 + drivers/pinctrl/renesas/Makefile | 1 + drivers/pinctrl/renesas/pfc-r8a779h0.c | 3969 ++++++++++++++++++++ drivers/pinctrl/renesas/pfc.c | 11 + drivers/pinctrl/renesas/sh_pfc.h | 1 + drivers/spi/renesas_rpc_spi.c | 3 +- include/configs/grayhawk.h | 14 + .../dt-bindings/clock/renesas,r8a779h0-cpg-mssr.h | 96 + include/dt-bindings/power/renesas,r8a779h0-sysc.h | 49 + 30 files changed, 5395 insertions(+), 2 deletions(-) create mode 100644 arch/arm/dts/r8a779h0-gray-hawk-cpu.dtsi create mode 100644 arch/arm/dts/r8a779h0-gray-hawk-csi-dsi.dtsi create mode 100644 arch/arm/dts/r8a779h0-gray-hawk-ethernet.dtsi create mode 100644 arch/arm/dts/r8a779h0-gray-hawk-u-boot.dts create mode 100644 arch/arm/dts/r8a779h0-gray-hawk.dts create mode 100644 arch/arm/dts/r8a779h0-u-boot.dtsi create mode 100644 arch/arm/dts/r8a779h0.dtsi create mode 100644 board/renesas/grayhawk/Kconfig create mode 100644 board/renesas/grayhawk/MAINTAINERS create mode 100644 board/renesas/grayhawk/Makefile create mode 100644 board/renesas/grayhawk/grayhawk.c create mode 100644 configs/r8a779h0_grayhawk_defconfig create mode 100644 drivers/clk/renesas/r8a779h0-cpg-mssr.c create mode 100644 drivers/pinctrl/renesas/pfc-r8a779h0.c create mode 100644 include/configs/grayhawk.h create mode 100644 include/dt-bindings/clock/renesas,r8a779h0-cpg-mssr.h create mode 100644 include/dt-bindings/power/renesas,r8a779h0-sysc.h

2 1

[PATCH] sunxi: defconfig: Add pstore support for pinephone
by Andrey Skvortsov 11 Feb '24

11 Feb '24

In general any DRAM address, that isn't overwritten during a boot is suitable for pstore. Range from 0x40000000 - 0x50000000 is heavily used by u-boot for internal use and to load kernel, fdt, fdto, scripts, pxefile and ramdisk later in the boot process. Ramdisk start address is 0x4FF00000, initramfs for kernel with some hacking features and debug info enabled can take more than 100Mb and final address will be around 0x58000000. Address 0x61000000 will most likely not overlap with that. Signed-off-by: Andrey Skvortsov <andrej.skvortzov(a)gmail.com> --- configs/pinephone_defconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/configs/pinephone_defconfig b/configs/pinephone_defconfig index 9d39204a43..7b80cc3131 100644 --- a/configs/pinephone_defconfig +++ b/configs/pinephone_defconfig @@ -10,6 +10,8 @@ CONFIG_DRAM_ZQ=3881949 CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_PINEPHONE_DT_SELECTION=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_CMD_PSTORE=y +CONFIG_CMD_PSTORE_MEM_ADDR=0x61000000 CONFIG_OF_LIST="sun50i-a64-pinephone-1.1 sun50i-a64-pinephone-1.2" CONFIG_LED_STATUS=y CONFIG_LED_STATUS_GPIO=y -- 2.43.0

2 2

[PATCH] clk: renesas: Fix broken clocks on all Gen2 boards
by Niklas Söderlund 11 Feb '24

11 Feb '24

To prepare support for multiple register layouts pointers to register tables where added to struct cpg_mssr_info. These pointers are suppose to be filled in at probe time and no intended change in behavior was intended. However the new pointers where only filled in by some paths of the driver implemented in clk-rcar-gen3.c. The path implemented in clk-rcar-gen2.c was not updated leaving the pointers uninitialized leading to a crash when trying to probe the clocks. Fix this by filling in the pointers in the Gen2 code path with the values used before they where moved to struct cpg_mssr_info. Fixes: d413214fb748 ("clk: renesas: Add register pointers into struct cpg_mssr_info") Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas(a)ragnatech.se> --- drivers/clk/renesas/clk-rcar-gen2.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/clk/renesas/clk-rcar-gen2.c b/drivers/clk/renesas/clk-rcar-gen2.c index 66ffef96b695..89f2d9667469 100644 --- a/drivers/clk/renesas/clk-rcar-gen2.c +++ b/drivers/clk/renesas/clk-rcar-gen2.c @@ -298,6 +298,15 @@ int gen2_clk_probe(struct udevice *dev) if (!priv->cpg_pll_config->extal_div) return -EINVAL; + if (info->reg_layout == CLK_REG_LAYOUT_RCAR_GEN2_AND_GEN3) { + priv->info->status_regs = mstpsr; + priv->info->control_regs = smstpcr; + priv->info->reset_regs = srcr; + priv->info->reset_clear_regs = srstclr; + } else { + return -EINVAL; + } + ret = clk_get_by_name(dev, "extal", &priv->clk_extal); if (ret < 0) return ret; -- 2.43.0

3 2

[PATCH 00/15] rockchip: rk3328: Update defconfigs, DTs and enable boot from SPI
by Jonas Karlman 11 Feb '24

11 Feb '24

This series contains miscellaneous updates to defconfigs, syncs latest device trees from linux, fixes an issue loading FIT from SD-card when running SPL from eMMC and enables building a bootable SPI image on RK3328 boards. I am also adding myself as a reviewer for the three RK3328 boards I own. Patch 1-7 updates boards to enable similar Kconfig options and use a common order for from where to try and load FIT. Patch 8 fix loading FIT from SD-card when booting from eMMC by using pinctrl for emmc and sdmmc in SPL. Patch 9-10 makes rockchip gpio and rng driver compatible with linux. Patch 11 sync latest rk3328 device tree files from linux v6.8-rc1. Patch 12 reverts an old commit that added duplicated code. Patch 13-15 enables building u-boot-rockchip-spi.bin for boards with SPI flash. This series depends on the "rockchip: Fix ethernet on Radxa ROCK Pi E v1.21" series at [1]. [1] https://patchwork.ozlabs.org/cover/1887729/ Jonas Karlman (15): rockchip: rk3328: Update default u-boot,spl-boot-order prop rockchip: rk3328-evb: Update defconfig rockchip: rk3328-rock64: Update defconfig rockchip: rk3328-roc-cc: Update defconfig rockchip: rk3328-rock-pi-e: Update defconfig rockchip: rk3328-nanopi-r2: Update defconfig rockchip: rk3328-orangepi-r1-plus: Update defconfig rockchip: rk3328: Fix loading FIT from SD-card when booting from eMMC gpio: rockchip: Use gpio alias id as gpio bank id rng: rockchip: Use same compatible as linux rockchip: rk3328: Sync device tree from linux v6.8-rc1 Revert "rockchip: Allow booting from SPI" rockchip: rk3328: Add support to build bootable SPI image rockchip: rk3328-rock64: Enable boot from SPI NOR flash rockchip: rk3328-orangepi-r1-plus: Enable boot from SPI NOR flash arch/arm/dts/rk3328-evb-u-boot.dtsi | 4 + arch/arm/dts/rk3328-evb.dts | 1 + .../dts/rk3328-nanopi-r2c-plus-u-boot.dtsi | 6 -- arch/arm/dts/rk3328-nanopi-r2s-u-boot.dtsi | 28 ------ arch/arm/dts/rk3328-nanopi-r2s.dts | 3 +- .../rk3328-orangepi-r1-plus-lts-u-boot.dtsi | 36 ++----- arch/arm/dts/rk3328-orangepi-r1-plus-lts.dts | 4 +- .../dts/rk3328-orangepi-r1-plus-u-boot.dtsi | 36 ++----- arch/arm/dts/rk3328-orangepi-r1-plus.dts | 1 + arch/arm/dts/rk3328-roc-cc-u-boot.dtsi | 22 +---- arch/arm/dts/rk3328-roc-cc.dts | 3 +- arch/arm/dts/rk3328-rock-pi-e-u-boot.dtsi | 17 ---- arch/arm/dts/rk3328-rock-pi-e.dts | 55 +++++++++++ arch/arm/dts/rk3328-rock64-u-boot.dtsi | 30 ++---- arch/arm/dts/rk3328-rock64.dts | 1 + arch/arm/dts/rk3328-u-boot.dtsi | 99 +++++++++++++++---- arch/arm/dts/rk3328.dtsi | 64 +++++++++--- arch/arm/dts/rk3399-u-boot.dtsi | 2 +- arch/arm/mach-rockchip/rk3328/rk3328.c | 1 + arch/arm/mach-rockchip/spl-boot-order.c | 3 - board/rockchip/evb_rk3328/MAINTAINERS | 11 +++ board/rockchip/evb_rk3328/README | 70 ------------- configs/evb-rk3328_defconfig | 16 ++- configs/nanopi-r2c-plus-rk3328_defconfig | 11 ++- configs/nanopi-r2c-rk3328_defconfig | 11 ++- configs/nanopi-r2s-rk3328_defconfig | 11 ++- configs/orangepi-r1-plus-lts-rk3328_defconfig | 20 +++- configs/orangepi-r1-plus-rk3328_defconfig | 20 +++- configs/roc-cc-rk3328_defconfig | 9 +- configs/rock-pi-e-rk3328_defconfig | 10 +- configs/rock64-rk3328_defconfig | 15 ++- doc/board/rockchip/rockchip.rst | 9 +- drivers/gpio/rk_gpio.c | 7 +- drivers/rng/rockchip_rng.c | 10 +- 34 files changed, 351 insertions(+), 295 deletions(-) delete mode 100644 board/rockchip/evb_rk3328/README -- 2.43.0

9 38

[PATCH RFC 0/6] video: Add UTF-8 support for UEFI applications
by Janne Grunau via B4 Relay 10 Feb '24

10 Feb '24

Andre submitted 2 years ago DM_VIDEO improvements for UEFI applications using UEFI's EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL but did not follow with suggested changes. This series takes care of the UTF-8 support which required to draw symbol and box drawing characters used by UEFI applications like grub2 and sd-boot correctly. Compared to Andre's version this version has the following changes: - use and extend existing conversion functions from lib/charset.c - convert first to UTF-32 to support the truetype console as well - conversion is conditional on CONFIG_EFI_LOADER - use escape sequences in tests as proposed by Heinrich Link: https://lore.kernel.org/u-boot/20220110005638.21599-1-andre.przywara@arm.co… Signed-off-by: Janne Grunau <j(a)jannau.net> --- Andre Przywara (2): efi_selftest: Add international characters test efi_selftest: Add box drawing character selftest Janne Grunau (4): lib: charset: Fix utf8_to_utf32_stream() return value doc string video: console: Parse UTF-8 character sequences lib/charset: Map cp437 low chars (0x01 - 0x1f) from unicode efi_selftest: Add symbol character selftest drivers/video/console_normal.c | 6 +++-- drivers/video/console_rotate.c | 16 +++++++++----- drivers/video/console_truetype.c | 8 +++---- drivers/video/vidconsole-uclass.c | 18 ++++++++++----- drivers/video/vidconsole_internal.h | 15 +++++++++++++ include/charset.h | 4 ++-- include/cp1250.h | 12 ++++++++-- include/cp437.h | 12 ++++++++-- include/video_console.h | 10 +++++---- lib/charset.c | 9 +++++--- lib/efi_loader/efi_unicode_collation.c | 2 +- lib/efi_selftest/efi_selftest_textoutput.c | 35 ++++++++++++++++++++++++++++++ 12 files changed, 116 insertions(+), 31 deletions(-) --- base-commit: 866ca972d6c3cabeaf6dbac431e8e08bb30b3c8e change-id: 20240117-vidconsole-utf8-uefi-fa23b4ac65d6 Best regards, -- Janne Grunau <j(a)jannau.net>

4 16

[PATCH v3 0/2] smbios: fill wake-up type
by Heinrich Schuchardt 10 Feb '24

10 Feb '24

We should not use the reserved value 0x00 for the wake up type but use 0x06 (Power Switch). Correctly display wake-up type in smbios command. Display SMBIOS type 1 field family in smbios command. v3: provide an enum for the wake-up type constants v2: use wake-up type 0x02 as our default *** BLURB HERE *** Heinrich Schuchardt (2): cmd: smbios: type 1 wake-up time, family smbios: fill wake-up type cmd/smbios.c | 25 +++++++++++++++++++++++-- include/smbios.h | 27 +++++++++++++++++++++++++++ lib/smbios.c | 1 + 3 files changed, 51 insertions(+), 2 deletions(-) -- 2.43.0

1 2

[PATCH V3 00/11] board/ti: k3 boards: Stop using findfdt
by Nishanth Menon 09 Feb '24

09 Feb '24

This is a wide cleanup to switch to setting fdtfile using env_set instead of scripted magic. 'fdtfile' is expected to be set by default. This allows the stdboot triggered efi loaders to find the correct OS device tree file even if regular boot process is interrupted by user intervention. Updates from V2: * New patch #1 added for older omap platform build breakage (sorry about that) Bootlogs (no change from V1): https://gist.github.com/nmenon/843e343cde645ec4aa57b60cece5256a based on master 6faba41927bd Prepare v2024.04-rc1 NOTE: There are a couple of checkpatch WARN (around LATE_INIT) and CHECK (fdt_ops #ifdeffery) that on closer inspection looks fine and consistent with other similar usage. V2: https://lore.kernel.org/all/20240109191506.3820908-1-nm@ti.com/ V1: https://lore.kernel.org/all/20240108173301.2692332-1-nm@ti.com/ Nishanth Menon (11): board: ti: Add missing common/Kconfig references board: ti: common: Introduce a common fdt ops library board: ti: am62ax: Set fdtfile from C code instead of findfdt script board: ti: am62x: Set fdtfile from C code instead of findfdt script board: ti: am64x: Set fdtfile from C code instead of findfdt script board: ti: am65x: Set fdtfile from C code instead of findfdt script board: ti: j721e: Set fdtfile from C code instead of findfdt script board: ti: j721s2: Set fdtfile from C code instead of findfdt script board: beagle: beagleboneai64: Set fdtfile from C code instead of findfdt script board: beagle: beagleplay: Set fdtfile from C code instead of findfdt script include: env: ti: Drop default_findfdt board/beagle/beagleboneai64/beagleboneai64.c | 14 ++++ .../beagle/beagleboneai64/beagleboneai64.env | 1 - board/beagle/beagleplay/beagleplay.c | 14 ++++ board/beagle/beagleplay/beagleplay.env | 1 - board/ti/am62ax/am62ax.env | 1 - board/ti/am62ax/evm.c | 10 +++ board/ti/am62x/am62x.env | 1 - board/ti/am62x/evm.c | 8 +++ board/ti/am64x/am64x.env | 9 --- board/ti/am64x/evm.c | 8 +++ board/ti/am65x/am65x.env | 3 - board/ti/am65x/evm.c | 2 + board/ti/common/Kconfig | 12 ++++ board/ti/common/Makefile | 1 + board/ti/common/fdt_ops.c | 64 +++++++++++++++++++ board/ti/common/fdt_ops.h | 42 ++++++++++++ board/ti/j721e/evm.c | 8 +++ board/ti/j721e/j721e.env | 10 --- board/ti/j721s2/evm.c | 8 +++ board/ti/j721s2/j721s2.env | 8 --- board/ti/omap3evm/Kconfig | 2 + board/ti/panda/Kconfig | 2 + board/ti/sdp4430/Kconfig | 2 + configs/am62ax_evm_a53_defconfig | 1 + configs/am62x_beagleplay_a53_defconfig | 3 +- configs/am62x_evm_a53_defconfig | 1 + configs/j721e_beagleboneai64_a72_defconfig | 3 +- include/env/ti/default_findfdt.env | 12 ---- 28 files changed, 203 insertions(+), 48 deletions(-) create mode 100644 board/ti/common/fdt_ops.c create mode 100644 board/ti/common/fdt_ops.h delete mode 100644 include/env/ti/default_findfdt.env base-commit: 6faba41927bdc8973b59678649ef83c564cc421e -- 2.43.0

2 12

[GIT PULL] Please pull u-boot-dfu-20240209
by Mattijs Korpershoek 09 Feb '24

09 Feb '24

Hi Tom, Here are some developments for master including: - sparse error checking fix when using raw chunks - 2 new additions (AVB, AB) of myself to the MAINTAINERS file The CI job is at https://source.denx.de/u-boot/custodians/u-boot-dfu/-/pipelines/19573 Thanks, Mattijs The following changes since commit a4650bf65e4b7d3ef04c90ba8031374428e4a682: ti: keystone2: Move common Kconfig selections to under ARCH_KEYSTONE (2024-02-08 14:42:56 -0500) are available in the Git repository at: https://source.denx.de/u-boot/custodians/u-boot-dfu.git tags/u-boot-dfu-20240209 for you to fetch changes up to 766f04a297e892d5106f7f7ac8b43c69bd8a6007: lib: sparse: Fix error checking for write_sparse_chunk_raw (2024-02-09 09:42:04 +0100) ---------------------------------------------------------------- u-boot-dfu-20240209 - sparse error checking fix when using raw chunks - 2 new additions (AVB, AB) of myself to the MAINTAINERS file ---------------------------------------------------------------- Mattijs Korpershoek (2): MAINTAINERS: add Mattijs for Android AB MAINTAINERS: add Mattijs for Android AVB Sean Anderson (1): lib: sparse: Fix error checking for write_sparse_chunk_raw MAINTAINERS | 2 ++ lib/image-sparse.c | 2 +- 2 files changed, 3 insertions(+), 1 deletion(-)

2 1