December 2024 - U-Boot

[PATCH 00/12] rockchip: rk3399: Migrate to use TPL on bob and kevin
by Jonas Karlman 10 Jan '25

10 Jan '25

This is a continuation of an RFC [1] sent back in August. All Rockchip aarch64 boards, beside bob and kevin, use TPL to initialize DRAM and SPL to load FIT with U-Boot proper and TF-A. Bob and kevin currently does not use TPL and instead initialize DRAM in SPL and directly after tries to load a FIT with only U-Boot proper. This series migrate bob and kevin to also use TPL to uniform TPL/SPL use for all Rockchip aarch64 boards. Features and changes in this series: - Use of Rockchip aarch64 common bss and stack addresses - SHA256 checksum/signature check of FIT images in SPL - Use of dcache to speed up checksum check in SPL - SDMA use for eMMC access to speed up read/write in U-Boot proper - FIT location moved from 0x40000 to 0xE0000 in SPI flash Changes sinc RFC: - Include pinctrl props and enable regulators based on DT in SPL - Drop bob and kevin board specific code from common rk3399.c Please note that I do not have any bob or kevin so this has only been compile tested and the original RFC [1] was runtime tested by Simon. [1] https://patchwork.ozlabs.org/patch/1967517/ Jonas Karlman (12): rockchip: rk3399: Fix TPL build of bob and kevin rockchip: rk3399-gru: Use SYS_SPI_U_BOOT_OFFS value in offset prop rockchip: rk3399-gru: Move SPI flash payload offset for bob and kevin rockchip: rk3399-gru: Fix include of TPL in u-boot.rom image rockchip: rk3399-gru: Use TPL with common bss and stack addresses rockchip: rk3399-gru: Include binman generated FIT in u-boot.rom image rockchip: rk3399: Drop common Kconfig options already implied rockchip: rk3399-gru: Remove unused nodes from xPL control FDT rockchip: rk3399-gru: Enable dcache and signature validation in SPL rockchip: rk3399-gru: Use SDMA mode to read from eMMC rockchip: rk3399-gru: Include pinctrl and regulators in SPL rockchip: rk3399: Drop unneeded bob and kevin board specific code arch/arm/dts/rk3399-gru-u-boot.dtsi | 29 ++++++++++++++++++++++++-- arch/arm/dts/rk3399-u-boot.dtsi | 14 +++++++++++-- arch/arm/mach-rockchip/rk3399/Kconfig | 12 ----------- arch/arm/mach-rockchip/rk3399/rk3399.c | 23 +------------------- configs/chromebook_bob_defconfig | 23 ++++++-------------- configs/chromebook_kevin_defconfig | 23 ++++++-------------- 6 files changed, 52 insertions(+), 72 deletions(-) -- 2.47.1

5 30

[PATCH v3 0/7] efi: Start to chip away at the EFI workaround
by Simon Glass 10 Jan '25

10 Jan '25

At present there is a function, efi_set_bootdev(), which is used in various places to tell the EFI loader which device a file came from. With bootstd, this information is available in the bootflow. This little series provides a way for bootstd to provide the bootflow to the EFI loader, so that it is able to select the correct paths. For now only the EFI bootmeth is updated. Changes in v3: - Make calculate_paths() static and add a comment - Add new patch to support PXE booting - Rebase on Tom's tree (i.e. without the pointers/addresses series) https://patchwork.ozlabs.org/project/uboot/list/?series=436241 Changes in v2: - Adjust argument ordering for efi_run_image() - Use efi_loader tag instead of efi - Drop unnecessary path removal - Fix 'require' typo - Move calculation of dev-name into a separate function Simon Glass (7): efi_loader: Refactor device and image paths into a function efi_loader: Make efi_run_image() static efi_loader: Update efi_run_image() to accept image and device path efi_loader: Add a version of efi_binary_run() with more parameters efi_loader: Move the fallback code from efi_run_image() efi_loader: Pass in the required parameters from EFI bootmeth bootmeth_efi: Support PXE booting boot/bootmeth_efi.c | 64 +------- include/efi_loader.h | 10 ++ lib/efi_loader/efi_bootbin.c | 276 ++++++++++++++++++++++++++--------- 3 files changed, 218 insertions(+), 132 deletions(-) -- 2.34.1

4 24

How would I do signature verification of standalone binary?
by Koch, Fabian 10 Jan '25

10 Jan '25

Hey all, I have a SoC which does secure boot in a multi staged process. (ROM loads a signed SPL to an aux core, which loads another signed SPL to main core, which loads a signed u-boot.img) But the thing I want u-boot to load, verify signature and then run/boot is a standalone binary app, not a Linux Kernel. (It does work fine when I load that and run it with the "go" command, but no signature verification is done as of now) All the research I did pointed towards using signed FIT images and then "bootm" to do the verification and loading. But I cannot get "bootm" to load a FIT containing only my raw binary standalone app. Is that road a dead-end and I need to do something completely else? I would love to stay as close to vanilla u-boot (or at least the SDK vanilla version) and not implement a fully custom signature verification. Any pointers would be highly appreciated. kind regards Fabian Informationspflicht nach Art. 13 und 14 DS-GVO: https://www.hima.com/de/informationen-DSGVO Information obligation according to Art. 13 and 14 DS-GVO: https://www.hima.com/en/information-GDPR HIMA Paul Hildebrandt GmbH, Albert-Bassermann-Str. 28, 68782 Bruehl bei Mannheim Gesellschaft mit beschraenkter Haftung, Sitz Bruehl, Deutschland - Registergericht Mannheim HRB 720409 USt-ID: DE 144286400 WEEE-Reg.-Nr.: DE87326515 Geschaeftsfuehrender Gesellschafter: Steffen Philipp, Geschaeftsfuehrer: Joerg de la Motte (Vorsitz), Dr. Michael Loebig Diese Nachricht und saemtliche Anhaenge sind vertraulich und duerfen nicht an Dritte weitergeleitet oder sonst veroeffentlicht werden, soweit nicht ausdruecklich etwas anderes bestimmt ist. Falls Sie nicht der beabsichtigte Empfaenger sind, bitten wir Sie, mit dem Absender Kontakt aufzunehmen und diese Nachricht und saemtliche Anhaenge von Ihrem System zu loeschen. Auch in diesem Fall sind Sie weder berechtigt, diese Nachricht oder etwaige Anhaenge zu kopieren noch deren Inhalt einem Dritten zugaenglich zu machen. This message and its attachments are confidential and can contain privileged information which may not be distributed or published, unless expressly stated otherwise. If you are not the intended recipient, please notify us immediately and delete this email and its attachments. If you have received this communication in error, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited.

2 1

[PATCH v3 0/3] rockchip: rk35xx: Implement checkboard() to print SoC variant
by Jonas Karlman 10 Jan '25

10 Jan '25

Information about what SoC model and variant can be found in OTP. This series use this information in checkboard() to print out the running SoC model and variant, should match what is printed on the SoC. There are some asumptions taken on how some of the OTP values are encoded, however for my boards this seem to match and something like one of the following is shown with this applied: SoC: RK3566 SoC: RK3566T SoC: RK3568 SoC: RK3568B2 SoC: RK3568J SoC: RK3582 SoC: RK3588 SoC: RK3588S SoC: RK3588S2 SoC: RK3308B SoC: RK3308B-S Changes in v3: - Fix build issue with MISC=n or ROCKCHIP_OTP=n - Remove use of cpu-version - Use log_debug() instead of debug() Changes in v2: - Drop changes in generic-rk35xx_defconfig - Update code comments - Add patch for rk3308 This can probably be converted into an sysinfo driver in a future series, once other pending changes to sysinfo core have settled. Jonas Karlman (3): rockchip: rk356x: Implement checkboard() to print SoC variant rockchip: rk3588: Implement checkboard() to print SoC variant rockchip: rk3308: Implement checkboard() to print SoC variant arch/arm/dts/rk356x-u-boot.dtsi | 4 ++ arch/arm/dts/rk3588s-u-boot.dtsi | 4 ++ arch/arm/mach-rockchip/rk3308/rk3308.c | 16 +++++++ arch/arm/mach-rockchip/rk3568/rk3568.c | 61 ++++++++++++++++++++++++++ arch/arm/mach-rockchip/rk3588/rk3588.c | 52 ++++++++++++++++++++++ 5 files changed, 137 insertions(+) -- 2.46.2

3 8

[PATCH] rockchip: rk3308-rock-s0: Fix SD-card boot on v1.1 hw revision
by Jonas Karlman 10 Jan '25

10 Jan '25

BootROM leave GPIO4_D6 configured as SDMMC_PWREN function and DW MMC driver set PWREN high in dwmci_init(). However, HW revision prior to v1.2 must pull GPIO4_D6 low to access sdmmc. For HW revision v1.2 the state of GPIO4_D6 has no impact. Upstream linux-rockchip maintainer tree has merged a patch "arm64: dts: rockchip: Fix sdmmc access on rk3308-rock-s0 v1.1 boards" for v6.14 to fix this issue. Add the upstream vmmc-supply regulator in board u-boot.dtsi and enable required Kconfig options to set GPIO4_D6 low to fix reading sdmmc on v1.1 hw revision. The regulator-3v3-vcc-sd and sdmmc-2030 nodes along with the vmmc-supply prop can be dropped once dts/upstream sync v6.14 DTs. Fixes: 25438c40a007 ("board: rockchip: Add Radxa ROCK S0") Signed-off-by: Jonas Karlman <jonas(a)kwiboo.se> --- arch/arm/dts/rk3308-rock-s0-u-boot.dtsi | 43 +++++++++++++++++++++++++ configs/rock-s0-rk3308_defconfig | 2 ++ 2 files changed, 45 insertions(+) diff --git a/arch/arm/dts/rk3308-rock-s0-u-boot.dtsi b/arch/arm/dts/rk3308-rock-s0-u-boot.dtsi index dd4cb8660b8d..3b849280c4ad 100644 --- a/arch/arm/dts/rk3308-rock-s0-u-boot.dtsi +++ b/arch/arm/dts/rk3308-rock-s0-u-boot.dtsi @@ -2,11 +2,50 @@ #include "rk3308-u-boot.dtsi" +/ { + /* + * HW revision prior to v1.2 must pull GPIO4_D6 low to access sdmmc. + * This is modeled as an always-on active low fixed regulator. + */ + vcc_sd: regulator-3v3-vcc-sd { + compatible = "regulator-fixed"; + gpios = <&gpio4 RK_PD6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_2030>; + regulator-name = "vcc_sd"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_io>; + }; +}; + &emmc_pwren { bootph-pre-ram; bootph-some-ram; }; +&gpio4 { + bootph-pre-ram; +}; + +&pinctrl { + sdmmc { + sdmmc_2030: sdmmc-2030 { + rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&sdmmc { + vmmc-supply = <&vcc_sd>; +}; + +&sdmmc_2030 { + bootph-pre-ram; +}; + &uart0 { bootph-all; clock-frequency = <24000000>; @@ -17,6 +56,10 @@ bootph-pre-ram; }; +&vcc_sd { + bootph-pre-ram; +}; + &vdd_core { regulator-init-microvolt = <1015000>; }; diff --git a/configs/rock-s0-rk3308_defconfig b/configs/rock-s0-rk3308_defconfig index 0a46e7bb1871..063e0b921d73 100644 --- a/configs/rock-s0-rk3308_defconfig +++ b/configs/rock-s0-rk3308_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_SKIP_LOWLEVEL_INIT=y CONFIG_COUNTER_FREQUENCY=24000000 CONFIG_ARCH_ROCKCHIP=y +CONFIG_SPL_GPIO=y CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3308-rock-s0" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3308=y @@ -53,6 +54,7 @@ CONFIG_PHY_ROCKCHIP_INNO_USB2=y CONFIG_PINCTRL=y CONFIG_REGULATOR_PWM=y CONFIG_DM_REGULATOR_FIXED=y +CONFIG_SPL_DM_REGULATOR_FIXED=y CONFIG_PWM_ROCKCHIP=y CONFIG_RAM=y CONFIG_BAUDRATE=1500000 -- 2.47.1

3 3

[PATCH v2] rockchip: use OF_UPSTREAM for rk3066a/rk3188
by Johan Jonker 10 Jan '25

10 Jan '25

The device tree for rk3066a/rk3188 combined is now available in the /dts/upstream directory. Use imply OF_UPSTREAM to migrate all rk3066a/rk3188 boards. Signed-off-by: Johan Jonker <jbx6244(a)gmail.com> --- Changed V2: remove Makefile entries --- arch/arm/dts/Makefile | 6 - arch/arm/dts/rk3066a-mk808.dts | 241 -------- arch/arm/dts/rk3066a-u-boot.dtsi | 20 - arch/arm/dts/rk3066a.dtsi | 880 ------------------------------ arch/arm/dts/rk3188-radxarock.dts | 389 ------------- arch/arm/dts/rk3188-u-boot.dtsi | 17 - arch/arm/dts/rk3188.dtsi | 815 --------------------------- arch/arm/dts/rk3xxx.dtsi | 488 ----------------- arch/arm/mach-rockchip/Kconfig | 2 + configs/mk808_defconfig | 4 +- configs/rock_defconfig | 4 +- 11 files changed, 6 insertions(+), 2860 deletions(-) delete mode 100644 arch/arm/dts/rk3066a-mk808.dts delete mode 100644 arch/arm/dts/rk3066a.dtsi delete mode 100644 arch/arm/dts/rk3188-radxarock.dts delete mode 100644 arch/arm/dts/rk3188.dtsi delete mode 100644 arch/arm/dts/rk3xxx.dtsi diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 6ad59aeed5f6..166f9628dc8a 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -55,15 +55,9 @@ dtb-$(CONFIG_MACH_S700) += \ dtb-$(CONFIG_ROCKCHIP_RK3036) += \ rk3036-sdk.dtb -dtb-$(CONFIG_ROCKCHIP_RK3066) += \ - rk3066a-mk808.dtb - dtb-$(CONFIG_ROCKCHIP_RK3128) += \ rk3128-evb.dtb -dtb-$(CONFIG_ROCKCHIP_RK3188) += \ - rk3188-radxarock.dtb - dtb-$(CONFIG_ROCKCHIP_RK322X) += \ rk3229-evb.dtb diff --git a/arch/arm/dts/rk3066a-mk808.dts b/arch/arm/dts/rk3066a-mk808.dts deleted file mode 100644 index 06790f05b395..000000000000 --- a/arch/arm/dts/rk3066a-mk808.dts +++ /dev/null @@ -1,241 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (c) 2016 Paweł Jarosz <paweljarosz3691(a)gmail.com> - */ - -/dts-v1/; -#include <dt-bindings/input/input.h> -#include "rk3066a.dtsi" - -/ { - model = "Rikomagic MK808"; - compatible = "rikomagic,mk808", "rockchip,rk3066a"; - - aliases { - mmc0 = &mmc0; - mmc1 = &mmc1; - }; - - chosen { - stdout-path = "serial2:115200n8"; - }; - - memory@60000000 { - reg = <0x60000000 0x40000000>; - device_type = "memory"; - }; - - adc-keys { - compatible = "adc-keys"; - io-channels = <&saradc 1>; - io-channel-names = "buttons"; - keyup-threshold-microvolt = <2500000>; - poll-interval = <100>; - - button-recovery { - label = "recovery"; - linux,code = <KEY_VENDOR>; - press-threshold-microvolt = <0>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - blue_led: led-0 { - label = "mk808:blue:power"; - gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>; - default-state = "off"; - linux,default-trigger = "default-on"; - }; - }; - - hdmi_con { - compatible = "hdmi-connector"; - type = "c"; - - port { - hdmi_con_in: endpoint { - remote-endpoint = <&hdmi_out_con>; - }; - }; - }; - - vcc_2v5: vcc-2v5 { - compatible = "regulator-fixed"; - regulator-name = "vcc_2v5"; - regulator-min-microvolt = <2500000>; - regulator-max-microvolt = <2500000>; - }; - - vcc_io: vcc-io { - compatible = "regulator-fixed"; - regulator-name = "vcc_io"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vcc_host: usb-host-regulator { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&host_drv>; - pinctrl-names = "default"; - regulator-always-on; - regulator-name = "host-pwr"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - startup-delay-us = <100000>; - vin-supply = <&vcc_io>; - }; - - vcc_otg: usb-otg-regulator { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&otg_drv>; - pinctrl-names = "default"; - regulator-always-on; - regulator-name = "vcc_otg"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - startup-delay-us = <100000>; - vin-supply = <&vcc_io>; - }; - - vcc_sd: sdmmc-regulator { - compatible = "regulator-fixed"; - gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>; - pinctrl-0 = <&sdmmc_pwr>; - pinctrl-names = "default"; - regulator-name = "vcc_sd"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - startup-delay-us = <100000>; - vin-supply = <&vcc_io>; - }; - - vcc_wifi: sdio-regulator { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&gpio3 RK_PD0 GPIO_ACTIVE_HIGH>; - pinctrl-0 = <&wifi_pwr>; - pinctrl-names = "default"; - regulator-name = "vcc_wifi"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - startup-delay-us = <100000>; - vin-supply = <&vcc_io>; - }; -}; - -&hdmi { - status = "okay"; -}; - -&hdmi_in_vop1 { - status = "disabled"; -}; - -&hdmi_out { - hdmi_out_con: endpoint { - remote-endpoint = <&hdmi_con_in>; - }; -}; - -&mmc0 { - bus-width = <4>; - cap-mmc-highspeed; - cap-sd-highspeed; - vmmc-supply = <&vcc_sd>; - status = "okay"; -}; - -&mmc1 { - bus-width = <4>; - non-removable; - pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4>; - pinctrl-names = "default"; - vmmc-supply = <&vcc_wifi>; - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - brcmf: wifi@1 { - compatible = "brcm,bcm4329-fmac"; - reg = <1>; - }; -}; - -&nfc { - #address-cells = <1>; - #size-cells = <0>; - status = "okay"; - - nand@0 { - reg = <0>; - label = "rk-nand"; - nand-bus-width = <8>; - nand-ecc-mode = "hw"; - nand-ecc-step-size = <1024>; - nand-ecc-strength = <40>; - nand-is-boot-medium; - rockchip,boot-blks = <8>; - rockchip,boot-ecc-strength = <24>; - }; -}; - -&pinctrl { - usb-host { - host_drv: host-drv { - rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_default>; - }; - }; - - usb-otg { - otg_drv: otg-drv { - rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_default>; - }; - }; - - sdmmc { - sdmmc_pwr: sdmmc-pwr { - rockchip,pins = <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_default>; - }; - }; - - sdio { - wifi_pwr: wifi-pwr { - rockchip,pins = <3 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>; - }; - }; -}; - -&saradc { - vref-supply = <&vcc_2v5>; - status = "okay"; -}; - -&uart2 { - status = "okay"; -}; - -&usb_host { - status = "okay"; -}; - -&usb_otg { - status = "okay"; -}; - -&usbphy { - status = "okay"; -}; - -&vop0 { - status = "okay"; -}; - -&wdt { - status = "okay"; -}; diff --git a/arch/arm/dts/rk3066a-u-boot.dtsi b/arch/arm/dts/rk3066a-u-boot.dtsi index 06f405ca2c5e..d99db7853b59 100644 --- a/arch/arm/dts/rk3066a-u-boot.dtsi +++ b/arch/arm/dts/rk3066a-u-boot.dtsi @@ -3,26 +3,6 @@ #include "rockchip-u-boot.dtsi" #include "rk3xxx-u-boot.dtsi" -&gpio0 { - gpio-ranges = <&pinctrl 0 0 32>; -}; - -&gpio1 { - gpio-ranges = <&pinctrl 0 32 32>; -}; - -&gpio2 { - gpio-ranges = <&pinctrl 0 64 32>; -}; - -&gpio3 { - gpio-ranges = <&pinctrl 0 96 32>; -}; - -&gpio4 { - gpio-ranges = <&pinctrl 0 128 32>; -}; - &gpio6 { status = "disabled"; }; diff --git a/arch/arm/dts/rk3066a.dtsi b/arch/arm/dts/rk3066a.dtsi deleted file mode 100644 index de9915d946f7..000000000000 --- a/arch/arm/dts/rk3066a.dtsi +++ /dev/null @@ -1,880 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (c) 2013 MundoReader S.L. - * Author: Heiko Stuebner <heiko(a)sntech.de> - */ - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/rockchip.h> -#include <dt-bindings/clock/rk3066a-cru.h> -#include <dt-bindings/power/rk3066-power.h> -#include "rk3xxx.dtsi" - -/ { - compatible = "rockchip,rk3066a"; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - enable-method = "rockchip,rk3066-smp"; - - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - next-level-cache = <&L2>; - reg = <0x0>; - operating-points = - /* kHz uV */ - <1416000 1300000>, - <1200000 1175000>, - <1008000 1125000>, - <816000 1125000>, - <600000 1100000>, - <504000 1100000>, - <312000 1075000>; - clock-latency = <40000>; - clocks = <&cru ARMCLK>; - }; - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - next-level-cache = <&L2>; - reg = <0x1>; - }; - }; - - display-subsystem { - compatible = "rockchip,display-subsystem"; - ports = <&vop0_out>, <&vop1_out>; - }; - - sram: sram@10080000 { - compatible = "mmio-sram"; - reg = <0x10080000 0x10000>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x10080000 0x10000>; - - smp-sram@0 { - compatible = "rockchip,rk3066-smp-sram"; - reg = <0x0 0x50>; - }; - }; - - vop0: vop@1010c000 { - compatible = "rockchip,rk3066-vop"; - reg = <0x1010c000 0x19c>; - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru ACLK_LCDC0>, - <&cru DCLK_LCDC0>, - <&cru HCLK_LCDC0>; - clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; - power-domains = <&power RK3066_PD_VIO>; - resets = <&cru SRST_LCDC0_AXI>, - <&cru SRST_LCDC0_AHB>, - <&cru SRST_LCDC0_DCLK>; - reset-names = "axi", "ahb", "dclk"; - status = "disabled"; - - vop0_out: port { - #address-cells = <1>; - #size-cells = <0>; - - vop0_out_hdmi: endpoint@0 { - reg = <0>; - remote-endpoint = <&hdmi_in_vop0>; - }; - }; - }; - - vop1: vop@1010e000 { - compatible = "rockchip,rk3066-vop"; - reg = <0x1010e000 0x19c>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru ACLK_LCDC1>, - <&cru DCLK_LCDC1>, - <&cru HCLK_LCDC1>; - clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; - power-domains = <&power RK3066_PD_VIO>; - resets = <&cru SRST_LCDC1_AXI>, - <&cru SRST_LCDC1_AHB>, - <&cru SRST_LCDC1_DCLK>; - reset-names = "axi", "ahb", "dclk"; - status = "disabled"; - - vop1_out: port { - #address-cells = <1>; - #size-cells = <0>; - - vop1_out_hdmi: endpoint@0 { - reg = <0>; - remote-endpoint = <&hdmi_in_vop1>; - }; - }; - }; - - hdmi: hdmi@10116000 { - compatible = "rockchip,rk3066-hdmi"; - reg = <0x10116000 0x2000>; - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_HDMI>; - clock-names = "hclk"; - pinctrl-names = "default"; - pinctrl-0 = <&hdmii2c_xfer>, <&hdmi_hpd>; - power-domains = <&power RK3066_PD_VIO>; - rockchip,grf = <&grf>; - status = "disabled"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - hdmi_in: port@0 { - reg = <0>; - #address-cells = <1>; - #size-cells = <0>; - - hdmi_in_vop0: endpoint@0 { - reg = <0>; - remote-endpoint = <&vop0_out_hdmi>; - }; - - hdmi_in_vop1: endpoint@1 { - reg = <1>; - remote-endpoint = <&vop1_out_hdmi>; - }; - }; - - hdmi_out: port@1 { - reg = <1>; - }; - }; - }; - - i2s0: i2s@10118000 { - compatible = "rockchip,rk3066-i2s"; - reg = <0x10118000 0x2000>; - interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&i2s0_bus>; - clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0>; - clock-names = "i2s_clk", "i2s_hclk"; - dmas = <&dmac1_s 4>, <&dmac1_s 5>; - dma-names = "tx", "rx"; - rockchip,playback-channels = <8>; - rockchip,capture-channels = <2>; - #sound-dai-cells = <0>; - status = "disabled"; - }; - - i2s1: i2s@1011a000 { - compatible = "rockchip,rk3066-i2s"; - reg = <0x1011a000 0x2000>; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&i2s1_bus>; - clocks = <&cru SCLK_I2S1>, <&cru HCLK_I2S1>; - clock-names = "i2s_clk", "i2s_hclk"; - dmas = <&dmac1_s 6>, <&dmac1_s 7>; - dma-names = "tx", "rx"; - rockchip,playback-channels = <2>; - rockchip,capture-channels = <2>; - #sound-dai-cells = <0>; - status = "disabled"; - }; - - i2s2: i2s@1011c000 { - compatible = "rockchip,rk3066-i2s"; - reg = <0x1011c000 0x2000>; - interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&i2s2_bus>; - clocks = <&cru SCLK_I2S2>, <&cru HCLK_I2S2>; - clock-names = "i2s_clk", "i2s_hclk"; - dmas = <&dmac1_s 9>, <&dmac1_s 10>; - dma-names = "tx", "rx"; - rockchip,playback-channels = <2>; - rockchip,capture-channels = <2>; - #sound-dai-cells = <0>; - status = "disabled"; - }; - - cru: clock-controller@20000000 { - compatible = "rockchip,rk3066a-cru"; - reg = <0x20000000 0x1000>; - clocks = <&xin24m>; - clock-names = "xin24m"; - rockchip,grf = <&grf>; - #clock-cells = <1>; - #reset-cells = <1>; - assigned-clocks = <&cru PLL_CPLL>, <&cru PLL_GPLL>, - <&cru ACLK_CPU>, <&cru HCLK_CPU>, - <&cru PCLK_CPU>, <&cru ACLK_PERI>, - <&cru HCLK_PERI>, <&cru PCLK_PERI>; - assigned-clock-rates = <400000000>, <594000000>, - <300000000>, <150000000>, - <75000000>, <300000000>, - <150000000>, <75000000>; - }; - - timer2: timer@2000e000 { - compatible = "snps,dw-apb-timer"; - reg = <0x2000e000 0x100>; - interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru SCLK_TIMER2>, <&cru PCLK_TIMER2>; - clock-names = "timer", "pclk"; - }; - - efuse: efuse@20010000 { - compatible = "rockchip,rk3066a-efuse"; - reg = <0x20010000 0x4000>; - #address-cells = <1>; - #size-cells = <1>; - clocks = <&cru PCLK_EFUSE>; - clock-names = "pclk_efuse"; - - cpu_leakage: cpu_leakage@17 { - reg = <0x17 0x1>; - }; - }; - - timer0: timer@20038000 { - compatible = "snps,dw-apb-timer"; - reg = <0x20038000 0x100>; - interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru SCLK_TIMER0>, <&cru PCLK_TIMER0>; - clock-names = "timer", "pclk"; - }; - - timer1: timer@2003a000 { - compatible = "snps,dw-apb-timer"; - reg = <0x2003a000 0x100>; - interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru SCLK_TIMER1>, <&cru PCLK_TIMER1>; - clock-names = "timer", "pclk"; - }; - - tsadc: tsadc@20060000 { - compatible = "rockchip,rk3066-tsadc"; - reg = <0x20060000 0x100>; - clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; - clock-names = "saradc", "apb_pclk"; - interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; - #io-channel-cells = <1>; - resets = <&cru SRST_TSADC>; - reset-names = "saradc-apb"; - status = "disabled"; - }; - - pinctrl: pinctrl { - compatible = "rockchip,rk3066a-pinctrl"; - rockchip,grf = <&grf>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - gpio0: gpio@20034000 { - compatible = "rockchip,gpio-bank"; - reg = <0x20034000 0x100>; - interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO0>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio1: gpio@2003c000 { - compatible = "rockchip,gpio-bank"; - reg = <0x2003c000 0x100>; - interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO1>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio2: gpio@2003e000 { - compatible = "rockchip,gpio-bank"; - reg = <0x2003e000 0x100>; - interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO2>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio3: gpio@20080000 { - compatible = "rockchip,gpio-bank"; - reg = <0x20080000 0x100>; - interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO3>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio4: gpio@20084000 { - compatible = "rockchip,gpio-bank"; - reg = <0x20084000 0x100>; - interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO4>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio6: gpio@2000a000 { - compatible = "rockchip,gpio-bank"; - reg = <0x2000a000 0x100>; - interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO6>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - pcfg_pull_default: pcfg-pull-default { - bias-pull-pin-default; - }; - - pcfg_pull_none: pcfg-pull-none { - bias-disable; - }; - - emac { - emac_xfer: emac-xfer { - rockchip,pins = <1 RK_PC0 2 &pcfg_pull_none>, /* mac_clk */ - <1 RK_PC1 2 &pcfg_pull_none>, /* tx_en */ - <1 RK_PC2 2 &pcfg_pull_none>, /* txd1 */ - <1 RK_PC3 2 &pcfg_pull_none>, /* txd0 */ - <1 RK_PC4 2 &pcfg_pull_none>, /* rx_err */ - <1 RK_PC5 2 &pcfg_pull_none>, /* crs_dvalid */ - <1 RK_PC6 2 &pcfg_pull_none>, /* rxd1 */ - <1 RK_PC7 2 &pcfg_pull_none>; /* rxd0 */ - }; - - emac_mdio: emac-mdio { - rockchip,pins = <1 RK_PD0 2 &pcfg_pull_none>, /* mac_md */ - <1 RK_PD1 2 &pcfg_pull_none>; /* mac_mdclk */ - }; - }; - - emmc { - emmc_clk: emmc-clk { - rockchip,pins = <3 RK_PD7 2 &pcfg_pull_default>; - }; - - emmc_cmd: emmc-cmd { - rockchip,pins = <4 RK_PB1 2 &pcfg_pull_default>; - }; - - emmc_rst: emmc-rst { - rockchip,pins = <4 RK_PB2 2 &pcfg_pull_default>; - }; - - /* - * The data pins are shared between nandc and emmc and - * not accessible through pinctrl. Also they should've - * been already set correctly by firmware, as - * flash/emmc is the boot-device. - */ - }; - - hdmi { - hdmi_hpd: hdmi-hpd { - rockchip,pins = <0 RK_PA0 1 &pcfg_pull_default>; - }; - - hdmii2c_xfer: hdmii2c-xfer { - rockchip,pins = <0 RK_PA1 1 &pcfg_pull_none>, - <0 RK_PA2 1 &pcfg_pull_none>; - }; - }; - - i2c0 { - i2c0_xfer: i2c0-xfer { - rockchip,pins = <2 RK_PD4 1 &pcfg_pull_none>, - <2 RK_PD5 1 &pcfg_pull_none>; - }; - }; - - i2c1 { - i2c1_xfer: i2c1-xfer { - rockchip,pins = <2 RK_PD6 1 &pcfg_pull_none>, - <2 RK_PD7 1 &pcfg_pull_none>; - }; - }; - - i2c2 { - i2c2_xfer: i2c2-xfer { - rockchip,pins = <3 RK_PA0 1 &pcfg_pull_none>, - <3 RK_PA1 1 &pcfg_pull_none>; - }; - }; - - i2c3 { - i2c3_xfer: i2c3-xfer { - rockchip,pins = <3 RK_PA2 2 &pcfg_pull_none>, - <3 RK_PA3 2 &pcfg_pull_none>; - }; - }; - - i2c4 { - i2c4_xfer: i2c4-xfer { - rockchip,pins = <3 RK_PA4 1 &pcfg_pull_none>, - <3 RK_PA5 1 &pcfg_pull_none>; - }; - }; - - pwm0 { - pwm0_out: pwm0-out { - rockchip,pins = <0 RK_PA3 1 &pcfg_pull_none>; - }; - }; - - pwm1 { - pwm1_out: pwm1-out { - rockchip,pins = <0 RK_PA4 1 &pcfg_pull_none>; - }; - }; - - pwm2 { - pwm2_out: pwm2-out { - rockchip,pins = <0 RK_PD6 1 &pcfg_pull_none>; - }; - }; - - pwm3 { - pwm3_out: pwm3-out { - rockchip,pins = <0 RK_PD7 1 &pcfg_pull_none>; - }; - }; - - spi0 { - spi0_clk: spi0-clk { - rockchip,pins = <1 RK_PA5 2 &pcfg_pull_default>; - }; - spi0_cs0: spi0-cs0 { - rockchip,pins = <1 RK_PA4 2 &pcfg_pull_default>; - }; - spi0_tx: spi0-tx { - rockchip,pins = <1 RK_PA7 2 &pcfg_pull_default>; - }; - spi0_rx: spi0-rx { - rockchip,pins = <1 RK_PA6 2 &pcfg_pull_default>; - }; - spi0_cs1: spi0-cs1 { - rockchip,pins = <4 RK_PB7 1 &pcfg_pull_default>; - }; - }; - - spi1 { - spi1_clk: spi1-clk { - rockchip,pins = <2 RK_PC3 2 &pcfg_pull_default>; - }; - spi1_cs0: spi1-cs0 { - rockchip,pins = <2 RK_PC4 2 &pcfg_pull_default>; - }; - spi1_rx: spi1-rx { - rockchip,pins = <2 RK_PC6 2 &pcfg_pull_default>; - }; - spi1_tx: spi1-tx { - rockchip,pins = <2 RK_PC5 2 &pcfg_pull_default>; - }; - spi1_cs1: spi1-cs1 { - rockchip,pins = <2 RK_PC7 2 &pcfg_pull_default>; - }; - }; - - uart0 { - uart0_xfer: uart0-xfer { - rockchip,pins = <1 RK_PA0 1 &pcfg_pull_default>, - <1 RK_PA1 1 &pcfg_pull_default>; - }; - - uart0_cts: uart0-cts { - rockchip,pins = <1 RK_PA2 1 &pcfg_pull_default>; - }; - - uart0_rts: uart0-rts { - rockchip,pins = <1 RK_PA3 1 &pcfg_pull_default>; - }; - }; - - uart1 { - uart1_xfer: uart1-xfer { - rockchip,pins = <1 RK_PA4 1 &pcfg_pull_default>, - <1 RK_PA5 1 &pcfg_pull_default>; - }; - - uart1_cts: uart1-cts { - rockchip,pins = <1 RK_PA6 1 &pcfg_pull_default>; - }; - - uart1_rts: uart1-rts { - rockchip,pins = <1 RK_PA7 1 &pcfg_pull_default>; - }; - }; - - uart2 { - uart2_xfer: uart2-xfer { - rockchip,pins = <1 RK_PB0 1 &pcfg_pull_default>, - <1 RK_PB1 1 &pcfg_pull_default>; - }; - /* no rts / cts for uart2 */ - }; - - uart3 { - uart3_xfer: uart3-xfer { - rockchip,pins = <3 RK_PD3 1 &pcfg_pull_default>, - <3 RK_PD4 1 &pcfg_pull_default>; - }; - - uart3_cts: uart3-cts { - rockchip,pins = <3 RK_PD5 1 &pcfg_pull_default>; - }; - - uart3_rts: uart3-rts { - rockchip,pins = <3 RK_PD6 1 &pcfg_pull_default>; - }; - }; - - sd0 { - sd0_clk: sd0-clk { - rockchip,pins = <3 RK_PB0 1 &pcfg_pull_default>; - }; - - sd0_cmd: sd0-cmd { - rockchip,pins = <3 RK_PB1 1 &pcfg_pull_default>; - }; - - sd0_cd: sd0-cd { - rockchip,pins = <3 RK_PB6 1 &pcfg_pull_default>; - }; - - sd0_wp: sd0-wp { - rockchip,pins = <3 RK_PB7 1 &pcfg_pull_default>; - }; - - sd0_bus1: sd0-bus-width1 { - rockchip,pins = <3 RK_PB2 1 &pcfg_pull_default>; - }; - - sd0_bus4: sd0-bus-width4 { - rockchip,pins = <3 RK_PB2 1 &pcfg_pull_default>, - <3 RK_PB3 1 &pcfg_pull_default>, - <3 RK_PB4 1 &pcfg_pull_default>, - <3 RK_PB5 1 &pcfg_pull_default>; - }; - }; - - sd1 { - sd1_clk: sd1-clk { - rockchip,pins = <3 RK_PC5 1 &pcfg_pull_default>; - }; - - sd1_cmd: sd1-cmd { - rockchip,pins = <3 RK_PC0 1 &pcfg_pull_default>; - }; - - sd1_cd: sd1-cd { - rockchip,pins = <3 RK_PC6 1 &pcfg_pull_default>; - }; - - sd1_wp: sd1-wp { - rockchip,pins = <3 RK_PC7 1 &pcfg_pull_default>; - }; - - sd1_bus1: sd1-bus-width1 { - rockchip,pins = <3 RK_PC1 1 &pcfg_pull_default>; - }; - - sd1_bus4: sd1-bus-width4 { - rockchip,pins = <3 RK_PC1 1 &pcfg_pull_default>, - <3 RK_PC2 1 &pcfg_pull_default>, - <3 RK_PC3 1 &pcfg_pull_default>, - <3 RK_PC4 1 &pcfg_pull_default>; - }; - }; - - i2s0 { - i2s0_bus: i2s0-bus { - rockchip,pins = <0 RK_PA7 1 &pcfg_pull_default>, - <0 RK_PB0 1 &pcfg_pull_default>, - <0 RK_PB1 1 &pcfg_pull_default>, - <0 RK_PB2 1 &pcfg_pull_default>, - <0 RK_PB3 1 &pcfg_pull_default>, - <0 RK_PB4 1 &pcfg_pull_default>, - <0 RK_PB5 1 &pcfg_pull_default>, - <0 RK_PB6 1 &pcfg_pull_default>, - <0 RK_PB7 1 &pcfg_pull_default>; - }; - }; - - i2s1 { - i2s1_bus: i2s1-bus { - rockchip,pins = <0 RK_PC0 1 &pcfg_pull_default>, - <0 RK_PC1 1 &pcfg_pull_default>, - <0 RK_PC2 1 &pcfg_pull_default>, - <0 RK_PC3 1 &pcfg_pull_default>, - <0 RK_PC4 1 &pcfg_pull_default>, - <0 RK_PC5 1 &pcfg_pull_default>; - }; - }; - - i2s2 { - i2s2_bus: i2s2-bus { - rockchip,pins = <0 RK_PD0 1 &pcfg_pull_default>, - <0 RK_PD1 1 &pcfg_pull_default>, - <0 RK_PD2 1 &pcfg_pull_default>, - <0 RK_PD3 1 &pcfg_pull_default>, - <0 RK_PD4 1 &pcfg_pull_default>, - <0 RK_PD5 1 &pcfg_pull_default>; - }; - }; - }; -}; - -&gpu { - compatible = "rockchip,rk3066-mali", "arm,mali-400"; - interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "gp", - "gpmmu", - "pp0", - "ppmmu0", - "pp1", - "ppmmu1", - "pp2", - "ppmmu2", - "pp3", - "ppmmu3"; - power-domains = <&power RK3066_PD_GPU>; -}; - -&grf { - compatible = "rockchip,rk3066-grf", "syscon", "simple-mfd"; - - usbphy: usbphy { - compatible = "rockchip,rk3066a-usb-phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - usbphy0: usb-phy@17c { - reg = <0x17c>; - clocks = <&cru SCLK_OTGPHY0>; - clock-names = "phyclk"; - #clock-cells = <0>; - #phy-cells = <0>; - }; - - usbphy1: usb-phy@188 { - reg = <0x188>; - clocks = <&cru SCLK_OTGPHY1>; - clock-names = "phyclk"; - #clock-cells = <0>; - #phy-cells = <0>; - }; - }; -}; - -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_xfer>; -}; - -&i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_xfer>; -}; - -&i2c2 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_xfer>; -}; - -&i2c3 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_xfer>; -}; - -&i2c4 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_xfer>; -}; - -&mmc0 { - clock-frequency = <50000000>; - dmas = <&dmac2 1>; - dma-names = "rx-tx"; - max-frequency = <50000000>; - pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus4>; -}; - -&mmc1 { - dmas = <&dmac2 3>; - dma-names = "rx-tx"; - pinctrl-names = "default"; - pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus4>; -}; - -&emmc { - dmas = <&dmac2 4>; - dma-names = "rx-tx"; -}; - -&pmu { - power: power-controller { - compatible = "rockchip,rk3066-power-controller"; - #power-domain-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - - power-domain@RK3066_PD_VIO { - reg = <RK3066_PD_VIO>; - clocks = <&cru ACLK_LCDC0>, - <&cru ACLK_LCDC1>, - <&cru DCLK_LCDC0>, - <&cru DCLK_LCDC1>, - <&cru HCLK_LCDC0>, - <&cru HCLK_LCDC1>, - <&cru SCLK_CIF1>, - <&cru ACLK_CIF1>, - <&cru HCLK_CIF1>, - <&cru SCLK_CIF0>, - <&cru ACLK_CIF0>, - <&cru HCLK_CIF0>, - <&cru HCLK_HDMI>, - <&cru ACLK_IPP>, - <&cru HCLK_IPP>, - <&cru ACLK_RGA>, - <&cru HCLK_RGA>; - pm_qos = <&qos_lcdc0>, - <&qos_lcdc1>, - <&qos_cif0>, - <&qos_cif1>, - <&qos_ipp>, - <&qos_rga>; - #power-domain-cells = <0>; - }; - - power-domain@RK3066_PD_VIDEO { - reg = <RK3066_PD_VIDEO>; - clocks = <&cru ACLK_VDPU>, - <&cru ACLK_VEPU>, - <&cru HCLK_VDPU>, - <&cru HCLK_VEPU>; - pm_qos = <&qos_vpu>; - #power-domain-cells = <0>; - }; - - power-domain@RK3066_PD_GPU { - reg = <RK3066_PD_GPU>; - clocks = <&cru ACLK_GPU>; - pm_qos = <&qos_gpu>; - #power-domain-cells = <0>; - }; - }; -}; - -&pwm0 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_out>; -}; - -&pwm1 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm1_out>; -}; - -&pwm2 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm2_out>; -}; - -&pwm3 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm3_out>; -}; - -&spi0 { - pinctrl-names = "default"; - pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>; -}; - -&spi1 { - pinctrl-names = "default"; - pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>; -}; - -&uart0 { - compatible = "rockchip,rk3066-uart", "snps,dw-apb-uart"; - dmas = <&dmac1_s 0>, <&dmac1_s 1>; - dma-names = "tx", "rx"; - pinctrl-names = "default"; - pinctrl-0 = <&uart0_xfer>; -}; - -&uart1 { - compatible = "rockchip,rk3066-uart", "snps,dw-apb-uart"; - dmas = <&dmac1_s 2>, <&dmac1_s 3>; - dma-names = "tx", "rx"; - pinctrl-names = "default"; - pinctrl-0 = <&uart1_xfer>; -}; - -&uart2 { - compatible = "rockchip,rk3066-uart", "snps,dw-apb-uart"; - dmas = <&dmac2 6>, <&dmac2 7>; - dma-names = "tx", "rx"; - pinctrl-names = "default"; - pinctrl-0 = <&uart2_xfer>; -}; - -&uart3 { - compatible = "rockchip,rk3066-uart", "snps,dw-apb-uart"; - dmas = <&dmac2 8>, <&dmac2 9>; - dma-names = "tx", "rx"; - pinctrl-names = "default"; - pinctrl-0 = <&uart3_xfer>; -}; - -&vpu { - power-domains = <&power RK3066_PD_VIDEO>; -}; - -&wdt { - compatible = "rockchip,rk3066-wdt", "snps,dw-wdt"; -}; - -&emac { - compatible = "rockchip,rk3066-emac"; -}; diff --git a/arch/arm/dts/rk3188-radxarock.dts b/arch/arm/dts/rk3188-radxarock.dts deleted file mode 100644 index 118deacd38c4..000000000000 --- a/arch/arm/dts/rk3188-radxarock.dts +++ /dev/null @@ -1,389 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (c) 2013 Heiko Stuebner <heiko(a)sntech.de> - */ - -/dts-v1/; -#include <dt-bindings/input/input.h> -#include "rk3188.dtsi" - -/ { - model = "Radxa Rock"; - compatible = "radxa,rock", "rockchip,rk3188"; - - aliases { - mmc0 = &mmc0; - }; - - memory@60000000 { - device_type = "memory"; - reg = <0x60000000 0x80000000>; - }; - - gpio-keys { - compatible = "gpio-keys"; - autorepeat; - - key-power { - gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; - linux,code = <KEY_POWER>; - label = "GPIO Key Power"; - linux,input-type = <1>; - wakeup-source; - debounce-interval = <100>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - green_led: led-0 { - label = "rock:green:user1"; - gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - blue_led: led-1 { - label = "rock:blue:user2"; - gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>; - default-state = "off"; - }; - - sleep_led: led-2 { - label = "rock:red:power"; - gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - sound { - compatible = "simple-audio-card"; - simple-audio-card,name = "SPDIF"; - - simple-audio-card,dai-link@1 { /* S/PDIF - S/PDIF */ - cpu { sound-dai = <&spdif>; }; - codec { sound-dai = <&spdif_out>; }; - }; - }; - - spdif_out: spdif-out { - compatible = "linux,spdif-dit"; - #sound-dai-cells = <0>; - }; - - ir_recv: ir-receiver { - compatible = "gpio-ir-receiver"; - gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&ir_recv_pin>; - }; - - vcc_otg: usb-otg-regulator { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&gpio2 RK_PD7 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&otg_vbus_drv>; - regulator-name = "otg-vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - vcc_sd0: sdmmc-regulator { - compatible = "regulator-fixed"; - regulator-name = "sdmmc-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&sdmmc_pwr>; - startup-delay-us = <100000>; - vin-supply = <&vcc_io>; - }; - - vcc_host: usb-host-regulator { - compatible = "regulator-fixed"; - enable-active-high; - gpio = <&gpio0 RK_PA3 GPIO_ACTIVE_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&host_vbus_drv>; - regulator-name = "host-pwr"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - vsys: vsys-regulator { - compatible = "regulator-fixed"; - regulator-name = "vsys"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-boot-on; - }; -}; - -&emac { - phy = <&phy0>; - phy-supply = <&vcc_rmii>; - pinctrl-names = "default"; - pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; - status = "okay"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - phy0: ethernet-phy@0 { - reg = <0>; - interrupt-parent = <&gpio3>; - interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>; - }; - }; -}; - -&cpu0 { - cpu-supply = <&vdd_arm>; -}; - -&cpu1 { - cpu-supply = <&vdd_arm>; -}; - -&cpu2 { - cpu-supply = <&vdd_arm>; -}; - -&cpu3 { - cpu-supply = <&vdd_arm>; -}; - -&gpu { - status = "okay"; -}; - -&i2c1 { - status = "okay"; - clock-frequency = <400000>; - - rtc@51 { - compatible = "haoyu,hym8563"; - reg = <0x51>; - interrupt-parent = <&gpio0>; - interrupts = <RK_PB5 IRQ_TYPE_EDGE_FALLING>; - pinctrl-names = "default"; - pinctrl-0 = <&rtc_int>; - #clock-cells = <0>; - clock-output-names = "xin32k"; - }; - - act8846: act8846@5a { - compatible = "active-semi,act8846"; - reg = <0x5a>; - status = "okay"; - system-power-controller; - - pinctrl-names = "default"; - pinctrl-0 = <&act8846_dvs0_ctl>; - - vp1-supply = <&vsys>; - vp2-supply = <&vsys>; - vp3-supply = <&vsys>; - vp4-supply = <&vsys>; - inl1-supply = <&vcc_io>; - inl2-supply = <&vsys>; - inl3-supply = <&vsys>; - - regulators { - vcc_ddr: REG1 { - regulator-name = "VCC_DDR"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - }; - - vdd_log: REG2 { - regulator-name = "VDD_LOG"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - vdd_arm: REG3 { - regulator-name = "VDD_ARM"; - regulator-min-microvolt = <875000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - }; - - vcc_io: REG4 { - regulator-name = "VCC_IO"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vdd_10: REG5 { - regulator-name = "VDD_10"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - }; - - vdd_hdmi: REG6 { - regulator-name = "VDD_HDMI"; - regulator-min-microvolt = <2500000>; - regulator-max-microvolt = <2500000>; - regulator-always-on; - }; - - vcc18: REG7 { - regulator-name = "VCC_18"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - vcca_33: REG8 { - regulator-name = "VCCA_33"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vcc_rmii: REG9 { - regulator-name = "VCC_RMII"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vccio_wl: REG10 { - regulator-name = "VCCIO_WL"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vcc_18: REG11 { - regulator-name = "VCC18_IO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - vcc28: REG12 { - regulator-name = "VCC_28"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - }; - }; - }; -}; - -&mmc0 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&sd0_clk>, <&sd0_cmd>, <&sd0_cd>, <&sd0_bus4>; - vmmc-supply = <&vcc_sd0>; - - bus-width = <4>; - cap-mmc-highspeed; - cap-sd-highspeed; - disable-wp; -}; - -&pwm1 { - status = "okay"; -}; - -&pwm2 { - status = "okay"; -}; - -&pwm3 { - status = "okay"; -}; - -&pinctrl { - pcfg_output_low: pcfg-output-low { - output-low; - }; - - act8846 { - act8846_dvs0_ctl: act8846-dvs0-ctl { - rockchip,pins = <3 RK_PD3 RK_FUNC_GPIO &pcfg_output_low>; - }; - }; - - hym8563 { - rtc_int: rtc-int { - rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>; - }; - }; - - lan8720a { - phy_int: phy-int { - rockchip,pins = <3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_up>; - }; - }; - - ir-receiver { - ir_recv_pin: ir-recv-pin { - rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; - }; - }; - - sd0 { - sdmmc_pwr: sdmmc-pwr { - rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>; - }; - }; - - usb { - host_vbus_drv: host-vbus-drv { - rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; - }; - otg_vbus_drv: otg-vbus-drv { - rockchip,pins = <2 RK_PD7 RK_FUNC_GPIO &pcfg_pull_none>; - }; - }; -}; - -&spdif { - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -&uart1 { - status = "okay"; -}; - -&uart2 { - status = "okay"; -}; - -&uart3 { - status = "okay"; -}; - -&usbphy { - status = "okay"; -}; - -&usb_host { - status = "okay"; -}; - -&usb_otg { - status = "okay"; -}; - -&wdt { - status = "okay"; -}; diff --git a/arch/arm/dts/rk3188-u-boot.dtsi b/arch/arm/dts/rk3188-u-boot.dtsi index 176f9e65c267..8f2849dda241 100644 --- a/arch/arm/dts/rk3188-u-boot.dtsi +++ b/arch/arm/dts/rk3188-u-boot.dtsi @@ -6,25 +6,8 @@ #include "rockchip-u-boot.dtsi" #include "rk3xxx-u-boot.dtsi" -&global_timer { - status = "okay"; -}; - &gpio0 { compatible = "rockchip,gpio-bank"; - gpio-ranges = <&pinctrl 0 0 32>; -}; - -&gpio1 { - gpio-ranges = <&pinctrl 0 32 32>; -}; - -&gpio2 { - gpio-ranges = <&pinctrl 0 64 32>; -}; - -&gpio3 { - gpio-ranges = <&pinctrl 0 96 32>; }; &pmu { diff --git a/arch/arm/dts/rk3188.dtsi b/arch/arm/dts/rk3188.dtsi deleted file mode 100644 index 44b54af0bbf9..000000000000 --- a/arch/arm/dts/rk3188.dtsi +++ /dev/null @@ -1,815 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (c) 2013 MundoReader S.L. - * Author: Heiko Stuebner <heiko(a)sntech.de> - */ - -#include <dt-bindings/gpio/gpio.h> -#include <dt-bindings/pinctrl/rockchip.h> -#include <dt-bindings/clock/rk3188-cru.h> -#include <dt-bindings/power/rk3188-power.h> -#include "rk3xxx.dtsi" - -/ { - compatible = "rockchip,rk3188"; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - enable-method = "rockchip,rk3066-smp"; - - cpu0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - next-level-cache = <&L2>; - reg = <0x0>; - clock-latency = <40000>; - clocks = <&cru ARMCLK>; - operating-points-v2 = <&cpu0_opp_table>; - resets = <&cru SRST_CORE0>; - }; - cpu1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - next-level-cache = <&L2>; - reg = <0x1>; - operating-points-v2 = <&cpu0_opp_table>; - resets = <&cru SRST_CORE1>; - }; - cpu2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - next-level-cache = <&L2>; - reg = <0x2>; - operating-points-v2 = <&cpu0_opp_table>; - resets = <&cru SRST_CORE2>; - }; - cpu3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a9"; - next-level-cache = <&L2>; - reg = <0x3>; - operating-points-v2 = <&cpu0_opp_table>; - resets = <&cru SRST_CORE3>; - }; - }; - - cpu0_opp_table: opp-table-0 { - compatible = "operating-points-v2"; - opp-shared; - - opp-312000000 { - opp-hz = /bits/ 64 <312000000>; - opp-microvolt = <875000>; - clock-latency-ns = <40000>; - }; - opp-504000000 { - opp-hz = /bits/ 64 <504000000>; - opp-microvolt = <925000>; - }; - opp-600000000 { - opp-hz = /bits/ 64 <600000000>; - opp-microvolt = <950000>; - opp-suspend; - }; - opp-816000000 { - opp-hz = /bits/ 64 <816000000>; - opp-microvolt = <975000>; - }; - opp-1008000000 { - opp-hz = /bits/ 64 <1008000000>; - opp-microvolt = <1075000>; - }; - opp-1200000000 { - opp-hz = /bits/ 64 <1200000000>; - opp-microvolt = <1150000>; - }; - opp-1416000000 { - opp-hz = /bits/ 64 <1416000000>; - opp-microvolt = <1250000>; - }; - opp-1608000000 { - opp-hz = /bits/ 64 <1608000000>; - opp-microvolt = <1350000>; - }; - }; - - display-subsystem { - compatible = "rockchip,display-subsystem"; - ports = <&vop0_out>, <&vop1_out>; - }; - - sram: sram@10080000 { - compatible = "mmio-sram"; - reg = <0x10080000 0x8000>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0x10080000 0x8000>; - - smp-sram@0 { - compatible = "rockchip,rk3066-smp-sram"; - reg = <0x0 0x50>; - }; - }; - - vop0: vop@1010c000 { - compatible = "rockchip,rk3188-vop"; - reg = <0x1010c000 0x1000>; - interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru ACLK_LCDC0>, <&cru DCLK_LCDC0>, <&cru HCLK_LCDC0>; - clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; - power-domains = <&power RK3188_PD_VIO>; - resets = <&cru SRST_LCDC0_AXI>, <&cru SRST_LCDC0_AHB>, <&cru SRST_LCDC0_DCLK>; - reset-names = "axi", "ahb", "dclk"; - status = "disabled"; - - vop0_out: port { - #address-cells = <1>; - #size-cells = <0>; - }; - }; - - vop1: vop@1010e000 { - compatible = "rockchip,rk3188-vop"; - reg = <0x1010e000 0x1000>; - interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru ACLK_LCDC1>, <&cru DCLK_LCDC1>, <&cru HCLK_LCDC1>; - clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; - power-domains = <&power RK3188_PD_VIO>; - resets = <&cru SRST_LCDC1_AXI>, <&cru SRST_LCDC1_AHB>, <&cru SRST_LCDC1_DCLK>; - reset-names = "axi", "ahb", "dclk"; - status = "disabled"; - - vop1_out: port { - #address-cells = <1>; - #size-cells = <0>; - }; - }; - - timer3: timer@2000e000 { - compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer"; - reg = <0x2000e000 0x20>; - interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_TIMER3>, <&cru SCLK_TIMER3>; - clock-names = "pclk", "timer"; - }; - - timer6: timer@200380a0 { - compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer"; - reg = <0x200380a0 0x20>; - interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER6>; - clock-names = "pclk", "timer"; - }; - - i2s0: i2s@1011a000 { - compatible = "rockchip,rk3188-i2s", "rockchip,rk3066-i2s"; - reg = <0x1011a000 0x2000>; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&i2s0_bus>; - clocks = <&cru SCLK_I2S0>, <&cru HCLK_I2S0>; - clock-names = "i2s_clk", "i2s_hclk"; - dmas = <&dmac1_s 6>, <&dmac1_s 7>; - dma-names = "tx", "rx"; - rockchip,playback-channels = <2>; - rockchip,capture-channels = <2>; - #sound-dai-cells = <0>; - status = "disabled"; - }; - - spdif: sound@1011e000 { - compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif"; - reg = <0x1011e000 0x2000>; - #sound-dai-cells = <0>; - clocks = <&cru SCLK_SPDIF>, <&cru HCLK_SPDIF>; - clock-names = "mclk", "hclk"; - dmas = <&dmac1_s 8>; - dma-names = "tx"; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - pinctrl-names = "default"; - pinctrl-0 = <&spdif_tx>; - status = "disabled"; - }; - - cru: clock-controller@20000000 { - compatible = "rockchip,rk3188-cru"; - reg = <0x20000000 0x1000>; - clocks = <&xin24m>; - clock-names = "xin24m"; - rockchip,grf = <&grf>; - #clock-cells = <1>; - #reset-cells = <1>; - }; - - efuse: efuse@20010000 { - compatible = "rockchip,rk3188-efuse"; - reg = <0x20010000 0x4000>; - #address-cells = <1>; - #size-cells = <1>; - clocks = <&cru PCLK_EFUSE>; - clock-names = "pclk_efuse"; - - cpu_leakage: cpu_leakage@17 { - reg = <0x17 0x1>; - }; - }; - - pinctrl: pinctrl { - compatible = "rockchip,rk3188-pinctrl"; - rockchip,grf = <&grf>; - rockchip,pmu = <&pmu>; - - #address-cells = <1>; - #size-cells = <1>; - ranges; - - gpio0: gpio@2000a000 { - compatible = "rockchip,rk3188-gpio-bank0"; - reg = <0x2000a000 0x100>; - interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO0>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio1: gpio@2003c000 { - compatible = "rockchip,gpio-bank"; - reg = <0x2003c000 0x100>; - interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO1>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio2: gpio@2003e000 { - compatible = "rockchip,gpio-bank"; - reg = <0x2003e000 0x100>; - interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO2>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio3: gpio@20080000 { - compatible = "rockchip,gpio-bank"; - reg = <0x20080000 0x100>; - interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru PCLK_GPIO3>; - - gpio-controller; - #gpio-cells = <2>; - - interrupt-controller; - #interrupt-cells = <2>; - }; - - pcfg_pull_up: pcfg-pull-up { - bias-pull-up; - }; - - pcfg_pull_down: pcfg-pull-down { - bias-pull-down; - }; - - pcfg_pull_none: pcfg-pull-none { - bias-disable; - }; - - emmc { - emmc_clk: emmc-clk { - rockchip,pins = <0 RK_PD0 2 &pcfg_pull_none>; - }; - - emmc_cmd: emmc-cmd { - rockchip,pins = <0 RK_PD2 2 &pcfg_pull_up>; - }; - - emmc_rst: emmc-rst { - rockchip,pins = <0 RK_PD3 2 &pcfg_pull_none>; - }; - - /* - * The data pins are shared between nandc and emmc and - * not accessible through pinctrl. Also they should've - * been already set correctly by firmware, as - * flash/emmc is the boot-device. - */ - }; - - emac { - emac_xfer: emac-xfer { - rockchip,pins = <3 RK_PC0 2 &pcfg_pull_none>, /* tx_en */ - <3 RK_PC1 2 &pcfg_pull_none>, /* txd1 */ - <3 RK_PC2 2 &pcfg_pull_none>, /* txd0 */ - <3 RK_PC3 2 &pcfg_pull_none>, /* rxd0 */ - <3 RK_PC4 2 &pcfg_pull_none>, /* rxd1 */ - <3 RK_PC5 2 &pcfg_pull_none>, /* mac_clk */ - <3 RK_PC6 2 &pcfg_pull_none>, /* rx_err */ - <3 RK_PC7 2 &pcfg_pull_none>; /* crs_dvalid */ - }; - - emac_mdio: emac-mdio { - rockchip,pins = <3 RK_PD0 2 &pcfg_pull_none>, - <3 RK_PD1 2 &pcfg_pull_none>; - }; - }; - - i2c0 { - i2c0_xfer: i2c0-xfer { - rockchip,pins = <1 RK_PD0 1 &pcfg_pull_none>, - <1 RK_PD1 1 &pcfg_pull_none>; - }; - }; - - i2c1 { - i2c1_xfer: i2c1-xfer { - rockchip,pins = <1 RK_PD2 1 &pcfg_pull_none>, - <1 RK_PD3 1 &pcfg_pull_none>; - }; - }; - - i2c2 { - i2c2_xfer: i2c2-xfer { - rockchip,pins = <1 RK_PD4 1 &pcfg_pull_none>, - <1 RK_PD5 1 &pcfg_pull_none>; - }; - }; - - i2c3 { - i2c3_xfer: i2c3-xfer { - rockchip,pins = <3 RK_PB6 2 &pcfg_pull_none>, - <3 RK_PB7 2 &pcfg_pull_none>; - }; - }; - - i2c4 { - i2c4_xfer: i2c4-xfer { - rockchip,pins = <1 RK_PD6 1 &pcfg_pull_none>, - <1 RK_PD7 1 &pcfg_pull_none>; - }; - }; - - lcdc1 { - lcdc1_dclk: lcdc1-dclk { - rockchip,pins = <2 RK_PD0 1 &pcfg_pull_none>; - }; - - lcdc1_den: lcdc1-den { - rockchip,pins = <2 RK_PD1 1 &pcfg_pull_none>; - }; - - lcdc1_hsync: lcdc1-hsync { - rockchip,pins = <2 RK_PD2 1 &pcfg_pull_none>; - }; - - lcdc1_vsync: lcdc1-vsync { - rockchip,pins = <2 RK_PD3 1 &pcfg_pull_none>; - }; - - lcdc1_rgb24: lcdc1-rgb24 { - rockchip,pins = <2 RK_PA0 1 &pcfg_pull_none>, - <2 RK_PA1 1 &pcfg_pull_none>, - <2 RK_PA2 1 &pcfg_pull_none>, - <2 RK_PA3 1 &pcfg_pull_none>, - <2 RK_PA4 1 &pcfg_pull_none>, - <2 RK_PA5 1 &pcfg_pull_none>, - <2 RK_PA6 1 &pcfg_pull_none>, - <2 RK_PA7 1 &pcfg_pull_none>, - <2 RK_PB0 1 &pcfg_pull_none>, - <2 RK_PB1 1 &pcfg_pull_none>, - <2 RK_PB2 1 &pcfg_pull_none>, - <2 RK_PB3 1 &pcfg_pull_none>, - <2 RK_PB4 1 &pcfg_pull_none>, - <2 RK_PB5 1 &pcfg_pull_none>, - <2 RK_PB6 1 &pcfg_pull_none>, - <2 RK_PB7 1 &pcfg_pull_none>, - <2 RK_PC0 1 &pcfg_pull_none>, - <2 RK_PC1 1 &pcfg_pull_none>, - <2 RK_PC2 1 &pcfg_pull_none>, - <2 RK_PC3 1 &pcfg_pull_none>, - <2 RK_PC4 1 &pcfg_pull_none>, - <2 RK_PC5 1 &pcfg_pull_none>, - <2 RK_PC6 1 &pcfg_pull_none>, - <2 RK_PC7 1 &pcfg_pull_none>; - }; - }; - - pwm0 { - pwm0_out: pwm0-out { - rockchip,pins = <3 RK_PD3 1 &pcfg_pull_none>; - }; - }; - - pwm1 { - pwm1_out: pwm1-out { - rockchip,pins = <3 RK_PD4 1 &pcfg_pull_none>; - }; - }; - - pwm2 { - pwm2_out: pwm2-out { - rockchip,pins = <3 RK_PD5 1 &pcfg_pull_none>; - }; - }; - - pwm3 { - pwm3_out: pwm3-out { - rockchip,pins = <3 RK_PD6 1 &pcfg_pull_none>; - }; - }; - - spi0 { - spi0_clk: spi0-clk { - rockchip,pins = <1 RK_PA6 2 &pcfg_pull_up>; - }; - spi0_cs0: spi0-cs0 { - rockchip,pins = <1 RK_PA7 2 &pcfg_pull_up>; - }; - spi0_tx: spi0-tx { - rockchip,pins = <1 RK_PA5 2 &pcfg_pull_up>; - }; - spi0_rx: spi0-rx { - rockchip,pins = <1 RK_PA4 2 &pcfg_pull_up>; - }; - spi0_cs1: spi0-cs1 { - rockchip,pins = <1 RK_PB7 1 &pcfg_pull_up>; - }; - }; - - spi1 { - spi1_clk: spi1-clk { - rockchip,pins = <0 RK_PD6 1 &pcfg_pull_up>; - }; - spi1_cs0: spi1-cs0 { - rockchip,pins = <0 RK_PD7 1 &pcfg_pull_up>; - }; - spi1_rx: spi1-rx { - rockchip,pins = <0 RK_PD4 1 &pcfg_pull_up>; - }; - spi1_tx: spi1-tx { - rockchip,pins = <0 RK_PD5 1 &pcfg_pull_up>; - }; - spi1_cs1: spi1-cs1 { - rockchip,pins = <1 RK_PB6 2 &pcfg_pull_up>; - }; - }; - - uart0 { - uart0_xfer: uart0-xfer { - rockchip,pins = <1 RK_PA0 1 &pcfg_pull_up>, - <1 RK_PA1 1 &pcfg_pull_none>; - }; - - uart0_cts: uart0-cts { - rockchip,pins = <1 RK_PA2 1 &pcfg_pull_none>; - }; - - uart0_rts: uart0-rts { - rockchip,pins = <1 RK_PA3 1 &pcfg_pull_none>; - }; - }; - - uart1 { - uart1_xfer: uart1-xfer { - rockchip,pins = <1 RK_PA4 1 &pcfg_pull_up>, - <1 RK_PA5 1 &pcfg_pull_none>; - }; - - uart1_cts: uart1-cts { - rockchip,pins = <1 RK_PA6 1 &pcfg_pull_none>; - }; - - uart1_rts: uart1-rts { - rockchip,pins = <1 RK_PA7 1 &pcfg_pull_none>; - }; - }; - - uart2 { - uart2_xfer: uart2-xfer { - rockchip,pins = <1 RK_PB0 1 &pcfg_pull_up>, - <1 RK_PB1 1 &pcfg_pull_none>; - }; - /* no rts / cts for uart2 */ - }; - - uart3 { - uart3_xfer: uart3-xfer { - rockchip,pins = <1 RK_PB2 1 &pcfg_pull_up>, - <1 RK_PB3 1 &pcfg_pull_none>; - }; - - uart3_cts: uart3-cts { - rockchip,pins = <1 RK_PB4 1 &pcfg_pull_none>; - }; - - uart3_rts: uart3-rts { - rockchip,pins = <1 RK_PB5 1 &pcfg_pull_none>; - }; - }; - - sd0 { - sd0_clk: sd0-clk { - rockchip,pins = <3 RK_PA2 1 &pcfg_pull_none>; - }; - - sd0_cmd: sd0-cmd { - rockchip,pins = <3 RK_PA3 1 &pcfg_pull_none>; - }; - - sd0_cd: sd0-cd { - rockchip,pins = <3 RK_PB0 1 &pcfg_pull_none>; - }; - - sd0_wp: sd0-wp { - rockchip,pins = <3 RK_PB1 1 &pcfg_pull_none>; - }; - - sd0_pwr: sd0-pwr { - rockchip,pins = <3 RK_PA1 1 &pcfg_pull_none>; - }; - - sd0_bus1: sd0-bus-width1 { - rockchip,pins = <3 RK_PA4 1 &pcfg_pull_none>; - }; - - sd0_bus4: sd0-bus-width4 { - rockchip,pins = <3 RK_PA4 1 &pcfg_pull_none>, - <3 RK_PA5 1 &pcfg_pull_none>, - <3 RK_PA6 1 &pcfg_pull_none>, - <3 RK_PA7 1 &pcfg_pull_none>; - }; - }; - - sd1 { - sd1_clk: sd1-clk { - rockchip,pins = <3 RK_PC5 1 &pcfg_pull_none>; - }; - - sd1_cmd: sd1-cmd { - rockchip,pins = <3 RK_PC0 1 &pcfg_pull_none>; - }; - - sd1_cd: sd1-cd { - rockchip,pins = <3 RK_PC6 1 &pcfg_pull_none>; - }; - - sd1_wp: sd1-wp { - rockchip,pins = <3 RK_PC7 1 &pcfg_pull_none>; - }; - - sd1_bus1: sd1-bus-width1 { - rockchip,pins = <3 RK_PC1 1 &pcfg_pull_none>; - }; - - sd1_bus4: sd1-bus-width4 { - rockchip,pins = <3 RK_PC1 1 &pcfg_pull_none>, - <3 RK_PC2 1 &pcfg_pull_none>, - <3 RK_PC3 1 &pcfg_pull_none>, - <3 RK_PC4 1 &pcfg_pull_none>; - }; - }; - - i2s0 { - i2s0_bus: i2s0-bus { - rockchip,pins = <1 RK_PC0 1 &pcfg_pull_none>, - <1 RK_PC1 1 &pcfg_pull_none>, - <1 RK_PC2 1 &pcfg_pull_none>, - <1 RK_PC3 1 &pcfg_pull_none>, - <1 RK_PC4 1 &pcfg_pull_none>, - <1 RK_PC5 1 &pcfg_pull_none>; - }; - }; - - spdif { - spdif_tx: spdif-tx { - rockchip,pins = <1 RK_PB6 1 &pcfg_pull_none>; - }; - }; - }; -}; - -&emac { - compatible = "rockchip,rk3188-emac"; -}; - -&global_timer { - interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; -}; - -&local_timer { - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; -}; - -&gpu { - compatible = "rockchip,rk3188-mali", "arm,mali-400"; - interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "gp", - "gpmmu", - "pp0", - "ppmmu0", - "pp1", - "ppmmu1", - "pp2", - "ppmmu2", - "pp3", - "ppmmu3"; - power-domains = <&power RK3188_PD_GPU>; -}; - -&grf { - compatible = "rockchip,rk3188-grf", "syscon", "simple-mfd"; - - io_domains: io-domains { - compatible = "rockchip,rk3188-io-voltage-domain"; - status = "disabled"; - }; - - usbphy: usbphy { - compatible = "rockchip,rk3188-usb-phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - usbphy0: usb-phy@10c { - reg = <0x10c>; - clocks = <&cru SCLK_OTGPHY0>; - clock-names = "phyclk"; - #clock-cells = <0>; - #phy-cells = <0>; - }; - - usbphy1: usb-phy@11c { - reg = <0x11c>; - clocks = <&cru SCLK_OTGPHY1>; - clock-names = "phyclk"; - #clock-cells = <0>; - #phy-cells = <0>; - }; - }; -}; - -&i2c0 { - compatible = "rockchip,rk3188-i2c"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_xfer>; -}; - -&i2c1 { - compatible = "rockchip,rk3188-i2c"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_xfer>; -}; - -&i2c2 { - compatible = "rockchip,rk3188-i2c"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c2_xfer>; -}; - -&i2c3 { - compatible = "rockchip,rk3188-i2c"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c3_xfer>; -}; - -&i2c4 { - compatible = "rockchip,rk3188-i2c"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c4_xfer>; -}; - -&pmu { - power: power-controller { - compatible = "rockchip,rk3188-power-controller"; - #power-domain-cells = <1>; - #address-cells = <1>; - #size-cells = <0>; - - power-domain@RK3188_PD_VIO { - reg = <RK3188_PD_VIO>; - clocks = <&cru ACLK_LCDC0>, - <&cru ACLK_LCDC1>, - <&cru DCLK_LCDC0>, - <&cru DCLK_LCDC1>, - <&cru HCLK_LCDC0>, - <&cru HCLK_LCDC1>, - <&cru SCLK_CIF0>, - <&cru ACLK_CIF0>, - <&cru HCLK_CIF0>, - <&cru ACLK_IPP>, - <&cru HCLK_IPP>, - <&cru ACLK_RGA>, - <&cru HCLK_RGA>; - pm_qos = <&qos_lcdc0>, - <&qos_lcdc1>, - <&qos_cif0>, - <&qos_ipp>, - <&qos_rga>; - #power-domain-cells = <0>; - }; - - power-domain@RK3188_PD_VIDEO { - reg = <RK3188_PD_VIDEO>; - clocks = <&cru ACLK_VDPU>, - <&cru ACLK_VEPU>, - <&cru HCLK_VDPU>, - <&cru HCLK_VEPU>; - pm_qos = <&qos_vpu>; - #power-domain-cells = <0>; - }; - - power-domain@RK3188_PD_GPU { - reg = <RK3188_PD_GPU>; - clocks = <&cru ACLK_GPU>; - pm_qos = <&qos_gpu>; - #power-domain-cells = <0>; - }; - }; -}; - -&pwm0 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm0_out>; -}; - -&pwm1 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm1_out>; -}; - -&pwm2 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm2_out>; -}; - -&pwm3 { - pinctrl-names = "default"; - pinctrl-0 = <&pwm3_out>; -}; - -&spi0 { - compatible = "rockchip,rk3188-spi", "rockchip,rk3066-spi"; - pinctrl-names = "default"; - pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>; -}; - -&spi1 { - compatible = "rockchip,rk3188-spi", "rockchip,rk3066-spi"; - pinctrl-names = "default"; - pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>; -}; - -&uart0 { - compatible = "rockchip,rk3188-uart", "snps,dw-apb-uart"; - pinctrl-names = "default"; - pinctrl-0 = <&uart0_xfer>; -}; - -&uart1 { - compatible = "rockchip,rk3188-uart", "snps,dw-apb-uart"; - pinctrl-names = "default"; - pinctrl-0 = <&uart1_xfer>; -}; - -&uart2 { - compatible = "rockchip,rk3188-uart", "snps,dw-apb-uart"; - pinctrl-names = "default"; - pinctrl-0 = <&uart2_xfer>; -}; - -&uart3 { - compatible = "rockchip,rk3188-uart", "snps,dw-apb-uart"; - pinctrl-names = "default"; - pinctrl-0 = <&uart3_xfer>; -}; - -&vpu { - compatible = "rockchip,rk3188-vpu", "rockchip,rk3066-vpu"; - power-domains = <&power RK3188_PD_VIDEO>; -}; - -&wdt { - compatible = "rockchip,rk3188-wdt", "snps,dw-wdt"; -}; diff --git a/arch/arm/dts/rk3xxx.dtsi b/arch/arm/dts/rk3xxx.dtsi deleted file mode 100644 index cb4e42ede56a..000000000000 --- a/arch/arm/dts/rk3xxx.dtsi +++ /dev/null @@ -1,488 +0,0 @@ -// SPDX-License-Identifier: (GPL-2.0+ OR MIT) -/* - * Copyright (c) 2013 MundoReader S.L. - * Author: Heiko Stuebner <heiko(a)sntech.de> - */ - -#include <dt-bindings/interrupt-controller/irq.h> -#include <dt-bindings/interrupt-controller/arm-gic.h> -#include <dt-bindings/soc/rockchip,boot-mode.h> - -/ { - #address-cells = <1>; - #size-cells = <1>; - - interrupt-parent = <&gic>; - - aliases { - ethernet0 = &emac; - i2c0 = &i2c0; - i2c1 = &i2c1; - i2c2 = &i2c2; - i2c3 = &i2c3; - i2c4 = &i2c4; - serial0 = &uart0; - serial1 = &uart1; - serial2 = &uart2; - serial3 = &uart3; - spi0 = &spi0; - spi1 = &spi1; - }; - - xin24m: oscillator { - compatible = "fixed-clock"; - clock-frequency = <24000000>; - #clock-cells = <0>; - clock-output-names = "xin24m"; - }; - - gpu: gpu@10090000 { - compatible = "arm,mali-400"; - reg = <0x10090000 0x10000>; - clocks = <&cru ACLK_GPU>, <&cru ACLK_GPU>; - clock-names = "bus", "core"; - assigned-clocks = <&cru ACLK_GPU>; - assigned-clock-rates = <100000000>; - resets = <&cru SRST_GPU>; - status = "disabled"; - }; - - vpu: video-codec@10104000 { - compatible = "rockchip,rk3066-vpu"; - reg = <0x10104000 0x800>; - interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "vepu", "vdpu"; - clocks = <&cru ACLK_VDPU>, <&cru HCLK_VDPU>, - <&cru ACLK_VEPU>, <&cru HCLK_VEPU>; - clock-names = "aclk_vdpu", "hclk_vdpu", - "aclk_vepu", "hclk_vepu"; - }; - - L2: cache-controller@10138000 { - compatible = "arm,pl310-cache"; - reg = <0x10138000 0x1000>; - cache-unified; - cache-level = <2>; - }; - - scu@1013c000 { - compatible = "arm,cortex-a9-scu"; - reg = <0x1013c000 0x100>; - }; - - global_timer: global-timer@1013c200 { - compatible = "arm,cortex-a9-global-timer"; - reg = <0x1013c200 0x20>; - interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>; - clocks = <&cru CORE_PERI>; - status = "disabled"; - /* The clock source and the sched_clock provided by the arm_global_timer - * on Rockchip rk3066a/rk3188 are quite unstable because their rates - * depend on the CPU frequency. - * Keep the arm_global_timer disabled in order to have the - * DW_APB_TIMER (rk3066a) or ROCKCHIP_TIMER (rk3188) selected by default. - */ - }; - - local_timer: local-timer@1013c600 { - compatible = "arm,cortex-a9-twd-timer"; - reg = <0x1013c600 0x20>; - interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>; - clocks = <&cru CORE_PERI>; - }; - - gic: interrupt-controller@1013d000 { - compatible = "arm,cortex-a9-gic"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0x1013d000 0x1000>, - <0x1013c100 0x0100>; - }; - - uart0: serial@10124000 { - compatible = "snps,dw-apb-uart"; - reg = <0x10124000 0x400>; - interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <1>; - clock-names = "baudclk", "apb_pclk"; - clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; - status = "disabled"; - }; - - uart1: serial@10126000 { - compatible = "snps,dw-apb-uart"; - reg = <0x10126000 0x400>; - interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <1>; - clock-names = "baudclk", "apb_pclk"; - clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; - status = "disabled"; - }; - - qos_gpu: qos@1012d000 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012d000 0x20>; - }; - - qos_vpu: qos@1012e000 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012e000 0x20>; - }; - - qos_lcdc0: qos@1012f000 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012f000 0x20>; - }; - - qos_cif0: qos@1012f080 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012f080 0x20>; - }; - - qos_ipp: qos@1012f100 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012f100 0x20>; - }; - - qos_lcdc1: qos@1012f180 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012f180 0x20>; - }; - - qos_cif1: qos@1012f200 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012f200 0x20>; - }; - - qos_rga: qos@1012f280 { - compatible = "rockchip,rk3066-qos", "syscon"; - reg = <0x1012f280 0x20>; - }; - - usb_otg: usb@10180000 { - compatible = "rockchip,rk3066-usb", "snps,dwc2"; - reg = <0x10180000 0x40000>; - interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_OTG0>; - clock-names = "otg"; - dr_mode = "otg"; - g-np-tx-fifo-size = <16>; - g-rx-fifo-size = <275>; - g-tx-fifo-size = <256 128 128 64 64 32>; - phys = <&usbphy0>; - phy-names = "usb2-phy"; - status = "disabled"; - }; - - usb_host: usb@101c0000 { - compatible = "snps,dwc2"; - reg = <0x101c0000 0x40000>; - interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_OTG1>; - clock-names = "otg"; - dr_mode = "host"; - phys = <&usbphy1>; - phy-names = "usb2-phy"; - status = "disabled"; - }; - - emac: ethernet@10204000 { - compatible = "snps,arc-emac"; - reg = <0x10204000 0x3c>; - interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; - - rockchip,grf = <&grf>; - - clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; - clock-names = "hclk", "macref"; - max-speed = <100>; - phy-mode = "rmii"; - - status = "disabled"; - }; - - mmc0: mmc@10214000 { - compatible = "rockchip,rk2928-dw-mshc"; - reg = <0x10214000 0x1000>; - interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>; - clock-names = "biu", "ciu"; - dmas = <&dmac2 1>; - dma-names = "rx-tx"; - fifo-depth = <256>; - resets = <&cru SRST_SDMMC>; - reset-names = "reset"; - status = "disabled"; - }; - - mmc1: mmc@10218000 { - compatible = "rockchip,rk2928-dw-mshc"; - reg = <0x10218000 0x1000>; - interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>; - clock-names = "biu", "ciu"; - dmas = <&dmac2 3>; - dma-names = "rx-tx"; - fifo-depth = <256>; - resets = <&cru SRST_SDIO>; - reset-names = "reset"; - status = "disabled"; - }; - - emmc: mmc@1021c000 { - compatible = "rockchip,rk2928-dw-mshc"; - reg = <0x1021c000 0x1000>; - interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>; - clock-names = "biu", "ciu"; - dmas = <&dmac2 4>; - dma-names = "rx-tx"; - fifo-depth = <256>; - resets = <&cru SRST_EMMC>; - reset-names = "reset"; - status = "disabled"; - }; - - nfc: nand-controller@10500000 { - compatible = "rockchip,rk2928-nfc"; - reg = <0x10500000 0x4000>; - interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&cru HCLK_NANDC0>; - clock-names = "ahb"; - status = "disabled"; - }; - - pmu: pmu@20004000 { - compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd"; - reg = <0x20004000 0x100>; - - reboot-mode { - compatible = "syscon-reboot-mode"; - offset = <0x40>; - mode-normal = <BOOT_NORMAL>; - mode-recovery = <BOOT_RECOVERY>; - mode-bootloader = <BOOT_FASTBOOT>; - mode-loader = <BOOT_BL_DOWNLOAD>; - }; - }; - - grf: grf@20008000 { - compatible = "syscon", "simple-mfd"; - reg = <0x20008000 0x200>; - }; - - dmac1_s: dma-controller@20018000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x20018000 0x4000>; - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMA1>; - clock-names = "apb_pclk"; - }; - - dmac1_ns: dma-controller@2001c000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x2001c000 0x4000>; - interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMA1>; - clock-names = "apb_pclk"; - status = "disabled"; - }; - - i2c0: i2c@2002d000 { - compatible = "rockchip,rk3066-i2c"; - reg = <0x2002d000 0x1000>; - interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - rockchip,grf = <&grf>; - - clock-names = "i2c"; - clocks = <&cru PCLK_I2C0>; - - status = "disabled"; - }; - - i2c1: i2c@2002f000 { - compatible = "rockchip,rk3066-i2c"; - reg = <0x2002f000 0x1000>; - interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - rockchip,grf = <&grf>; - - clocks = <&cru PCLK_I2C1>; - clock-names = "i2c"; - - status = "disabled"; - }; - - pwm0: pwm@20030000 { - compatible = "rockchip,rk2928-pwm"; - reg = <0x20030000 0x10>; - #pwm-cells = <2>; - clocks = <&cru PCLK_PWM01>; - status = "disabled"; - }; - - pwm1: pwm@20030010 { - compatible = "rockchip,rk2928-pwm"; - reg = <0x20030010 0x10>; - #pwm-cells = <2>; - clocks = <&cru PCLK_PWM01>; - status = "disabled"; - }; - - wdt: watchdog@2004c000 { - compatible = "snps,dw-wdt"; - reg = <0x2004c000 0x100>; - clocks = <&cru PCLK_WDT>; - interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - pwm2: pwm@20050020 { - compatible = "rockchip,rk2928-pwm"; - reg = <0x20050020 0x10>; - #pwm-cells = <2>; - clocks = <&cru PCLK_PWM23>; - status = "disabled"; - }; - - pwm3: pwm@20050030 { - compatible = "rockchip,rk2928-pwm"; - reg = <0x20050030 0x10>; - #pwm-cells = <2>; - clocks = <&cru PCLK_PWM23>; - status = "disabled"; - }; - - i2c2: i2c@20056000 { - compatible = "rockchip,rk3066-i2c"; - reg = <0x20056000 0x1000>; - interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - rockchip,grf = <&grf>; - - clocks = <&cru PCLK_I2C2>; - clock-names = "i2c"; - - status = "disabled"; - }; - - i2c3: i2c@2005a000 { - compatible = "rockchip,rk3066-i2c"; - reg = <0x2005a000 0x1000>; - interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - rockchip,grf = <&grf>; - - clocks = <&cru PCLK_I2C3>; - clock-names = "i2c"; - - status = "disabled"; - }; - - i2c4: i2c@2005e000 { - compatible = "rockchip,rk3066-i2c"; - reg = <0x2005e000 0x1000>; - interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; - #address-cells = <1>; - #size-cells = <0>; - - rockchip,grf = <&grf>; - - clocks = <&cru PCLK_I2C4>; - clock-names = "i2c"; - - status = "disabled"; - }; - - uart2: serial@20064000 { - compatible = "snps,dw-apb-uart"; - reg = <0x20064000 0x400>; - interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <1>; - clock-names = "baudclk", "apb_pclk"; - clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; - status = "disabled"; - }; - - uart3: serial@20068000 { - compatible = "snps,dw-apb-uart"; - reg = <0x20068000 0x400>; - interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; - reg-shift = <2>; - reg-io-width = <1>; - clock-names = "baudclk", "apb_pclk"; - clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>; - status = "disabled"; - }; - - saradc: saradc@2006c000 { - compatible = "rockchip,saradc"; - reg = <0x2006c000 0x100>; - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; - #io-channel-cells = <1>; - clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; - clock-names = "saradc", "apb_pclk"; - resets = <&cru SRST_SARADC>; - reset-names = "saradc-apb"; - status = "disabled"; - }; - - spi0: spi@20070000 { - compatible = "rockchip,rk3066-spi"; - clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; - clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x20070000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmac2 10>, <&dmac2 11>; - dma-names = "tx", "rx"; - status = "disabled"; - }; - - spi1: spi@20074000 { - compatible = "rockchip,rk3066-spi"; - clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>; - clock-names = "spiclk", "apb_pclk"; - interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; - reg = <0x20074000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - dmas = <&dmac2 12>, <&dmac2 13>; - dma-names = "tx", "rx"; - status = "disabled"; - }; - - dmac2: dma-controller@20078000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x20078000 0x4000>; - interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMA2>; - clock-names = "apb_pclk"; - }; -}; diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig index 92dca5e57600..a9420406649c 100644 --- a/arch/arm/mach-rockchip/Kconfig +++ b/arch/arm/mach-rockchip/Kconfig @@ -48,6 +48,7 @@ config ROCKCHIP_RK3066 select TPL select TPL_ROCKCHIP_BACK_TO_BROM select TPL_ROCKCHIP_EARLYRETURN_TO_BROM + imply OF_UPSTREAM imply ROCKCHIP_COMMON_BOARD imply SPL_ROCKCHIP_COMMON_BOARD imply SPL_SERIAL @@ -84,6 +85,7 @@ config ROCKCHIP_RK3188 select SPL_ROCKCHIP_EARLYRETURN_TO_BROM select SPL_ROCKCHIP_BACK_TO_BROM select BOARD_LATE_INIT + imply OF_UPSTREAM imply ROCKCHIP_COMMON_BOARD imply SPL_ROCKCHIP_COMMON_BOARD help diff --git a/configs/mk808_defconfig b/configs/mk808_defconfig index 12a37054b4da..e47d0b594f35 100644 --- a/configs/mk808_defconfig +++ b/configs/mk808_defconfig @@ -14,7 +14,7 @@ CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x78000000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_SIZE=0x8000 -CONFIG_DEFAULT_DEVICE_TREE="rk3066a-mk808" +CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3066a-mk808" CONFIG_DM_RESET=y CONFIG_ROCKCHIP_RK3066=y # CONFIG_ROCKCHIP_STIMER is not set @@ -35,7 +35,7 @@ CONFIG_SPL_PAYLOAD="u-boot.bin" CONFIG_DEBUG_UART=y CONFIG_SD_BOOT=y CONFIG_USE_PREBOOT=y -CONFIG_DEFAULT_FDT_FILE="rk3066a-mk808.dtb" +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3066a-mk808.dtb" CONFIG_SYS_CBSIZE=256 CONFIG_SYS_PBSIZE=276 # CONFIG_DISPLAY_CPUINFO is not set diff --git a/configs/rock_defconfig b/configs/rock_defconfig index d7f11310cba1..9c05bf451465 100644 --- a/configs/rock_defconfig +++ b/configs/rock_defconfig @@ -11,7 +11,7 @@ CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x60100000 CONFIG_SF_DEFAULT_SPEED=20000000 CONFIG_ENV_OFFSET=0x3F8000 -CONFIG_DEFAULT_DEVICE_TREE="rk3188-radxarock" +CONFIG_DEFAULT_DEVICE_TREE="rockchip/rk3188-radxarock" CONFIG_ROCKCHIP_RK3188=y # CONFIG_ROCKCHIP_STIMER is not set CONFIG_TARGET_ROCK=y @@ -25,7 +25,7 @@ CONFIG_DEBUG_UART_BASE=0x20064000 CONFIG_DEBUG_UART_CLOCK=24000000 CONFIG_DEBUG_UART=y CONFIG_USE_PREBOOT=y -CONFIG_DEFAULT_FDT_FILE="rk3188-radxarock.dtb" +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3188-radxarock.dtb" # CONFIG_DISPLAY_CPUINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_MAX_SIZE=0x7800 -- 2.39.5

3 2

[PATCH v2 0/4] rockchip: rk3288: Include files from dts/upstream
by Jonas Karlman 10 Jan '25

10 Jan '25

This series remove common rk3288 related device tree files that instead can be included directly from dts/upstream. No functional change to board DTs is intended with these removals. Changes in v2: - Keep code for use of gmac internal clock source - Collect r-b tags Jonas Karlman (4): rockchip: rk3288: Use rk3288-power.h from dts/upstream rockchip: clk: rk3288: Drop use of SCLK_MAC_PLL rockchip: rk3288: Use rk3288-cru.h from dts/upstream rockchip: rk3288: Use rk3288.dtsi from dts/upstream arch/arm/dts/rk3288-u-boot.dtsi | 9 - arch/arm/dts/rk3288.dtsi | 2035 ----------------- .../clock/rockchip,rk3288-cru.txt | 61 - drivers/clk/rockchip/clk_rk3288.c | 8 +- include/dt-bindings/clock/rk3288-cru.h | 381 --- include/dt-bindings/power/rk3288-power.h | 32 - 6 files changed, 4 insertions(+), 2522 deletions(-) delete mode 100644 arch/arm/dts/rk3288.dtsi delete mode 100644 doc/device-tree-bindings/clock/rockchip,rk3288-cru.txt delete mode 100644 include/dt-bindings/clock/rk3288-cru.h delete mode 100644 include/dt-bindings/power/rk3288-power.h -- 2.46.2

2 5

[PATCH 0/2] Broadcom bcmbca dts updates
by david regan 09 Jan '25

09 Jan '25

Updates for Broadcom bcmbca devices, make use of OF_UPSTREAM which uses Linux dts, update bcmbca dts to current nand node naming convention. david regan (2): arm: dts: Use upstream dts arm: dts: Update nand node arch/arm/dts/bcm4908.dtsi | 127 ---------------------- arch/arm/dts/bcm63138.dtsi | 149 -------------------------- arch/arm/dts/bcm63148.dtsi | 103 ------------------ arch/arm/dts/bcm94908.dts | 30 ------ arch/arm/dts/bcm963138.dts | 30 ------ arch/arm/dts/bcm963148.dts | 30 ------ arch/arm/dts/bcm96753ref.dts | 19 ++-- arch/arm/dts/bcm968360bg.dts | 19 ++-- arch/arm/dts/bcm968580xref.dts | 19 ++-- arch/arm/mach-bcmbca/bcm4908/Kconfig | 1 + arch/arm/mach-bcmbca/bcm63138/Kconfig | 1 + arch/arm/mach-bcmbca/bcm63148/Kconfig | 1 + configs/bcm94908_defconfig | 11 +- configs/bcm963138_defconfig | 11 +- configs/bcm963148_defconfig | 11 +- 15 files changed, 57 insertions(+), 505 deletions(-) delete mode 100644 arch/arm/dts/bcm4908.dtsi delete mode 100644 arch/arm/dts/bcm63138.dtsi delete mode 100644 arch/arm/dts/bcm63148.dtsi delete mode 100644 arch/arm/dts/bcm94908.dts delete mode 100644 arch/arm/dts/bcm963138.dts delete mode 100644 arch/arm/dts/bcm963148.dts -- 2.37.3

4 7

[PATCH v3 0/5] rpi: Tidy up booting
by Simon Glass 09 Jan '25

09 Jan '25

This series allows rpi to boot a compressed Ubuntu kernel with ~100MB ramdisk, by expanding the available space. It also tidies up some strange behaviour with the provided FDT, where a separate pointer is maintained to it, even though U-Boot has copied it and placed it in its own space. This avoids strange bugs where it accidentally gets overwritten when loading a file into memory. The patch to expand the devicetree was dropped, meaning that people should be careful to unset fdt_addr in the environment. Changes in v3: - Add to the existing comment block - Update the comment block with the new values, including compression Changes in v2: - Add new patch to make myself an rpi maintainer - Add new patch to set bootm_size - Add new patch to drop fdt_high and initrd_high - Drop patch to allow expanding the devicetree during relocation Simon Glass (5): rpi: Add myself to the list of maintainers rpi: Set bootm_size to 512MB rpi: Drop fdt_high and initrd_high rpi: Update environment to support booti and large initrd rpi: Use the U-Boot control FDT for fdt_addr MAINTAINERS | 1 + board/raspberrypi/rpi/rpi.c | 20 ++++++++----------- board/raspberrypi/rpi/rpi.env | 37 +++++++++++++++++++---------------- 3 files changed, 29 insertions(+), 29 deletions(-) -- 2.34.1

4 18

[PATCH v1 0/6] Enable SYS_64BIT_LBA flag for STM32MP
by Patrice Chotard 08 Jan '25

08 Jan '25

Enable SYS_64BIT_LBA flag in order to fix issue when flashing big binary using stm32prog. Patrice Chotard (6): fastboot: Fix warning when CONFIG_SYS_64BIT_LBA is enable arm: stm32mp: stm32prog: fix warning when CONFIG_SYS_64BIT_LBA is enable arm: stm32mp: stm32prog: update multiplier is part-size is above SZ_1G configs: stm32mp13: enable CONFIG_SYS_64BIT_LBA configs: stm32mp15: enable CONFIG_SYS_64BIT_LBA configs: stm32mp25: enable CONFIG_SYS_64BIT_LBA arch/arm/mach-stm32mp/cmd_stm32prog/stm32prog.c | 9 ++++++--- configs/stm32mp13_defconfig | 1 + configs/stm32mp15_basic_defconfig | 1 + configs/stm32mp15_defconfig | 1 + configs/stm32mp15_trusted_defconfig | 1 + configs/stm32mp25_defconfig | 1 + drivers/fastboot/fb_mmc.c | 8 ++++---- 7 files changed, 15 insertions(+), 7 deletions(-) -- 2.25.1

4 14