November 2024 - U-Boot

[PATCH] lds: align u-boot-nodtb with 8 bytes boundary
by Eugen Hristev 29 Jan '25

29 Jan '25

Newer DTC require that the DTB start address is aligned at 8 bytes. In the u-boot.bin case, the u-boot-nodtb.bin is concatenated with the DTB, but there is no alignment/padding to the next 8byte aligned address. This causes the board to fail booting, because the FDT will claim that the DTB inside u-boot.bin is not a valid DTB, it will fail with -FDT_ERR_ALIGNMENT. To solve this, have the u-boot binary `_end` aligned with 8 bytes. The objcopy in the Makefile will create the u-boot-nodtb.bin and it has to be truncated to 8 bytes to correspond to the u-boot.map file which will have the `_end` aligned to 8 bytes. The lds files which use devicetrees have been changed to align the `_end` tag with 8 bytes. This patch is also a prerequisite to have the possibility to update the dtc inside u-boot to newer versions (1.6.1+) Signed-off-by: Eugen Hristev <eugen.hristev(a)microchip.com> --- Hi, I could not test all affected boards, it's an impossible task. I tried this on at91 boards which I have, and ran the CI on denx. I cannot guarantee that no other boards are affected, so this patch is a bit of an RFC. If the u-boot-nodtb.bin does not have the size equal with the corresponding one in u-boot.map, the binary_size_check will fail at build time with something like this: u-boot.map shows a binary size of 502684 but u-boot-nodtb.bin shows 502688 Thanks, Eugen Makefile | 2 ++ arch/arm/cpu/armv8/u-boot.lds | 4 ++-- arch/arm/cpu/u-boot-spl.lds | 1 + arch/arm/cpu/u-boot.lds | 1 + arch/arm/lib/elf_arm_efi.lds | 5 +++++ arch/arm/mach-at91/arm926ejs/u-boot-spl.lds | 2 +- arch/arm/mach-at91/armv7/u-boot-spl.lds | 2 +- arch/arm/mach-zynq/u-boot-spl.lds | 2 +- arch/mips/cpu/u-boot.lds | 2 +- arch/sandbox/cpu/u-boot.lds | 6 ++++++ arch/sh/cpu/u-boot.lds | 2 ++ board/ti/am335x/u-boot.lds | 1 + tools/binman/test/u_boot_binman_embed.lds | 2 +- 13 files changed, 25 insertions(+), 7 deletions(-) diff --git a/Makefile b/Makefile index 9d84f96481..b4d387bcce 100644 --- a/Makefile +++ b/Makefile @@ -1317,6 +1317,8 @@ endif u-boot-nodtb.bin: u-boot FORCE $(call if_changed,objcopy_uboot) +# Make sure the size is 8 byte-aligned. + @truncate -s %8 $@ $(BOARD_SIZE_CHECK) u-boot.ldr: u-boot diff --git a/arch/arm/cpu/armv8/u-boot.lds b/arch/arm/cpu/armv8/u-boot.lds index 8fe4682dd2..e5fa4ef95c 100644 --- a/arch/arm/cpu/armv8/u-boot.lds +++ b/arch/arm/cpu/armv8/u-boot.lds @@ -145,10 +145,10 @@ SECTIONS *(.__rel_dyn_end) } - _end = .; - . = ALIGN(8); + _end = .; + .bss_start : { KEEP(*(.__bss_start)); } diff --git a/arch/arm/cpu/u-boot-spl.lds b/arch/arm/cpu/u-boot-spl.lds index fb2189d50d..732ed42db1 100644 --- a/arch/arm/cpu/u-boot-spl.lds +++ b/arch/arm/cpu/u-boot-spl.lds @@ -55,6 +55,7 @@ SECTIONS .end : { + . = ALIGN(8); *(.__end) } diff --git a/arch/arm/cpu/u-boot.lds b/arch/arm/cpu/u-boot.lds index f25f72b2e0..274e1a7d30 100644 --- a/arch/arm/cpu/u-boot.lds +++ b/arch/arm/cpu/u-boot.lds @@ -193,6 +193,7 @@ SECTIONS .end : { + . = ALIGN(8); *(.__end) } diff --git a/arch/arm/lib/elf_arm_efi.lds b/arch/arm/lib/elf_arm_efi.lds index 767ebda635..f3867021d3 100644 --- a/arch/arm/lib/elf_arm_efi.lds +++ b/arch/arm/lib/elf_arm_efi.lds @@ -54,6 +54,11 @@ SECTIONS .rel.data : { *(.rel.data) *(.rel.data*) } _data_size = . - _etext; + .end : { + . = ALIGN(8); + *(.__end) + } + /DISCARD/ : { *(.rel.reloc) *(.eh_frame) diff --git a/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds index 1a8bf94dee..d7e5d81ecc 100644 --- a/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds +++ b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds @@ -31,7 +31,7 @@ SECTIONS . = ALIGN(4); __u_boot_list : { KEEP(*(SORT(__u_boot_list*))) } > .sram - . = ALIGN(4); + . = ALIGN(8); __image_copy_end = .; .end : diff --git a/arch/arm/mach-at91/armv7/u-boot-spl.lds b/arch/arm/mach-at91/armv7/u-boot-spl.lds index 6ca725fc4c..2a0a1b4b86 100644 --- a/arch/arm/mach-at91/armv7/u-boot-spl.lds +++ b/arch/arm/mach-at91/armv7/u-boot-spl.lds @@ -38,7 +38,7 @@ SECTIONS . = ALIGN(4); __u_boot_list : { KEEP(*(SORT(__u_boot_list*))) } > .sram - . = ALIGN(4); + . = ALIGN(8); __image_copy_end = .; .end : diff --git a/arch/arm/mach-zynq/u-boot-spl.lds b/arch/arm/mach-zynq/u-boot-spl.lds index 8c18d3f91f..c0320dbe1e 100644 --- a/arch/arm/mach-zynq/u-boot-spl.lds +++ b/arch/arm/mach-zynq/u-boot-spl.lds @@ -41,7 +41,7 @@ SECTIONS KEEP(*(SORT(__u_boot_list*))); } > .sram - . = ALIGN(4); + . = ALIGN(8); _image_binary_end = .; diff --git a/arch/mips/cpu/u-boot.lds b/arch/mips/cpu/u-boot.lds index 9a4ebcd151..182e9bc6e5 100644 --- a/arch/mips/cpu/u-boot.lds +++ b/arch/mips/cpu/u-boot.lds @@ -56,7 +56,7 @@ SECTIONS . += CONFIG_MIPS_RELOCATION_TABLE_SIZE - 4; } - . = ALIGN(4); + . = ALIGN(8); _end = .; .bss __rel_start (OVERLAY) : { diff --git a/arch/sandbox/cpu/u-boot.lds b/arch/sandbox/cpu/u-boot.lds index ba8dee50c7..3fbca6d248 100644 --- a/arch/sandbox/cpu/u-boot.lds +++ b/arch/sandbox/cpu/u-boot.lds @@ -51,6 +51,12 @@ SECTIONS *(.dynsym) __dyn_sym_end = .; } + + .end : + { + . = ALIGN(8); + *(.__end) + } } INSERT BEFORE .data; diff --git a/arch/sh/cpu/u-boot.lds b/arch/sh/cpu/u-boot.lds index d360eea7eb..226f50b19c 100644 --- a/arch/sh/cpu/u-boot.lds +++ b/arch/sh/cpu/u-boot.lds @@ -74,6 +74,8 @@ SECTIONS KEEP(*(SORT(__u_boot_list*))); } >ram + . = ALIGN(8); + PROVIDE (__init_end = .); PROVIDE (reloc_dst_end = .); PROVIDE (_end = .); diff --git a/board/ti/am335x/u-boot.lds b/board/ti/am335x/u-boot.lds index 087dee8bb2..deb9098a90 100644 --- a/board/ti/am335x/u-boot.lds +++ b/board/ti/am335x/u-boot.lds @@ -118,6 +118,7 @@ SECTIONS .end : { + . = ALIGN(8); *(.__end) } diff --git a/tools/binman/test/u_boot_binman_embed.lds b/tools/binman/test/u_boot_binman_embed.lds index e213fa8a84..93c0ae6aed 100644 --- a/tools/binman/test/u_boot_binman_embed.lds +++ b/tools/binman/test/u_boot_binman_embed.lds @@ -18,7 +18,7 @@ SECTIONS *(.text*) } - . = ALIGN(4); + . = ALIGN(8); .data : { dtb_embed_begin = .; KEEP(*(.mydtb)); -- 2.25.1

8 26

[PATCH] board: solidrun: clearfog: enable ddr odt0 on write for both chip-select
by Josua Mayer 28 Jan '25

28 Jan '25

Enabling ODT is required to suppress reflection of the data signal on DDR write operation. SolidRun Armada 388 SoM only connects M_ODT[0] even when both chip-select are used. Enable ODT[0] for both chip-select during write only. Original work by Baruch Siach [1] and Chris Packham [2]. [1] https://github.com/SolidRun/u-boot-armada38x/commit/aba763a611e69fbcc4e2296… [2] https://github.com/SolidRun/u-boot-armada38x/commit/dbaf09590df9add19e738d2… Signed-off-by: Josua Mayer <josua(a)solid-run.com> --- board/solidrun/clearfog/clearfog.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 2dbd071abd9f29cee97fb813a67d0190a620bd32..67b60d2e7b43331383b6a01b13693b29b21129be 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -161,7 +161,7 @@ static struct mv_ddr_topology_map board_topology_map = { {0}, /* timing parameters */ { {0} }, /* electrical configuration */ {0,}, /* electrical parameters */ - 0, /* ODT configuration */ + 0x30000, /* ODT configuration */ 0x3, /* clock enable mask */ }; --- base-commit: 3881c6b90350b0b04085ad46ef64989b43967eef change-id: 20241127-a388-sr-som-odt-89f8dd6b6410 Best regards, -- Josua Mayer <josua(a)solid-run.com>

2 2

[PATCH] arm: kirkwood: Enable bootstd and other modernization for OpenRD boards
by Tony Dinh 28 Jan '25

28 Jan '25

Enable bootstd for OpenRD boards Update defconfigs to the latest u-boot requirements Remove JFFS2 support. See JFFS2 Vulnerability[1]. Move default envs to text-base environment [1] https://lore.kernel.org/u-boot/20241114233005.GN3600562@bill-the-cat/T/#m2f… Signed-off-by: Tony Dinh <mibodhi(a)gmail.com> --- arch/arm/mach-kirkwood/Kconfig | 1 + board/Marvell/openrd/openrd.env | 20 ++++++++++++++++++++ configs/openrd_base_defconfig | 18 +++++------------- configs/openrd_client_defconfig | 18 +++++------------- configs/openrd_ultimate_defconfig | 18 +++++------------- include/configs/openrd.h | 18 ------------------ 6 files changed, 36 insertions(+), 57 deletions(-) create mode 100644 board/Marvell/openrd/openrd.env diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig index 031d4e5ecd..6761a9cb39 100644 --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig @@ -38,6 +38,7 @@ config TARGET_OPENRD bool "Marvell OpenRD Board" select KW88F6281 select SHEEVA_88SV131 + select KIRKWOOD_COMMON config TARGET_DREAMPLUG bool "DreamPlug Board" diff --git a/board/Marvell/openrd/openrd.env b/board/Marvell/openrd/openrd.env new file mode 100644 index 0000000000..70ca704b73 --- /dev/null +++ b/board/Marvell/openrd/openrd.env @@ -0,0 +1,20 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2024 Tony Dinh <mibodhi(a)gmail.com> + * + * Environment variables configurations + */ + +kernel_addr_r=0x800000 +fdt_addr_r=0x2c00000 +ramdisk_addr_r=0x01100000 +scriptaddr=0x200000 +fdtfile=CONFIG_DEFAULT_DEVICE_TREE.dtb +mtdparts=CONFIG_MTDPARTS_DEFAULT +console=ttyS0,115200 + +/* Standard Boot */ +bootcmd= + bootflow scan -lb +failed= + echo CONFIG_SYS_BOARD boot failed - please check your image diff --git a/configs/openrd_base_defconfig b/configs/openrd_base_defconfig index 708bf5eefd..1ca0b45d93 100644 --- a/configs/openrd_base_defconfig +++ b/configs/openrd_base_defconfig @@ -4,22 +4,22 @@ CONFIG_SYS_DCACHE_OFF=y CONFIG_ARCH_CPU_INIT=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_KIRKWOOD=y +CONFIG_SUPPORT_PASSING_ATAGS=y +CONFIG_CMDLINE_TAG=y +CONFIG_INITRD_TAG=y CONFIG_SYS_KWD_CONFIG="board/Marvell/openrd/kwbimage.cfg" CONFIG_TEXT_BASE=0x600000 CONFIG_NR_DRAM_BANKS=2 -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_OPENRD=y CONFIG_ENV_SIZE=0x20000 CONFIG_ENV_OFFSET=0x80000 CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-openrd-base" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_IDENT_STRING="\nOpenRD-Base" -# CONFIG_SYS_MALLOC_F is not set CONFIG_HAS_BOARD_SIZE_LIMIT=y CONFIG_BOARD_SIZE_LIMIT=524288 +CONFIG_BOOTSTD_FULL=y CONFIG_BOOTDELAY=3 -CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;" CONFIG_USE_PREBOOT=y CONFIG_LOGLEVEL=2 # CONFIG_DISPLAY_BOARDINFO is not set @@ -30,23 +30,17 @@ CONFIG_CMD_MMC=y CONFIG_CMD_NAND=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_JFFS2=y CONFIG_CMD_MTDPARTS=y CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd" CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)" CONFIG_CMD_UBI=y -CONFIG_ISO_PARTITION=y CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_NAND=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NETCONSOLE=y CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SYS_ATA_STRIDE=4 CONFIG_SYS_ATA_DATA_OFFSET=0x100 CONFIG_SYS_ATA_REG_OFFSET=0x100 @@ -59,7 +53,5 @@ CONFIG_MTD=y CONFIG_MTD_RAW_NAND=y CONFIG_MVGBE=y CONFIG_MII=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SYS_NS16550_REG_SIZE=-4 CONFIG_USB=y CONFIG_USB_EHCI_HCD=y diff --git a/configs/openrd_client_defconfig b/configs/openrd_client_defconfig index 82a9c77761..e0cc2e65db 100644 --- a/configs/openrd_client_defconfig +++ b/configs/openrd_client_defconfig @@ -4,10 +4,12 @@ CONFIG_SYS_DCACHE_OFF=y CONFIG_ARCH_CPU_INIT=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_KIRKWOOD=y +CONFIG_SUPPORT_PASSING_ATAGS=y +CONFIG_CMDLINE_TAG=y +CONFIG_INITRD_TAG=y CONFIG_SYS_KWD_CONFIG="board/Marvell/openrd/kwbimage.cfg" CONFIG_TEXT_BASE=0x600000 CONFIG_NR_DRAM_BANKS=2 -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_OPENRD=y CONFIG_BOARD_IS_OPENRD_CLIENT=y CONFIG_ENV_SIZE=0x20000 @@ -15,12 +17,10 @@ CONFIG_ENV_OFFSET=0x80000 CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-openrd-client" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_IDENT_STRING="\nOpenRD-Client" -# CONFIG_SYS_MALLOC_F is not set CONFIG_HAS_BOARD_SIZE_LIMIT=y CONFIG_BOARD_SIZE_LIMIT=524288 +CONFIG_BOOTSTD_FULL=y CONFIG_BOOTDELAY=3 -CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;" CONFIG_USE_PREBOOT=y CONFIG_LOGLEVEL=2 # CONFIG_DISPLAY_BOARDINFO is not set @@ -31,23 +31,17 @@ CONFIG_CMD_MMC=y CONFIG_CMD_NAND=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_JFFS2=y CONFIG_CMD_MTDPARTS=y CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd" CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)" CONFIG_CMD_UBI=y -CONFIG_ISO_PARTITION=y CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_NAND=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NETCONSOLE=y CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SYS_ATA_STRIDE=4 CONFIG_SYS_ATA_DATA_OFFSET=0x100 CONFIG_SYS_ATA_REG_OFFSET=0x100 @@ -60,7 +54,5 @@ CONFIG_MTD=y CONFIG_MTD_RAW_NAND=y CONFIG_MVGBE=y CONFIG_MII=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SYS_NS16550_REG_SIZE=-4 CONFIG_USB=y CONFIG_USB_EHCI_HCD=y diff --git a/configs/openrd_ultimate_defconfig b/configs/openrd_ultimate_defconfig index 10b46e2ec1..a115691daa 100644 --- a/configs/openrd_ultimate_defconfig +++ b/configs/openrd_ultimate_defconfig @@ -4,10 +4,12 @@ CONFIG_SYS_DCACHE_OFF=y CONFIG_ARCH_CPU_INIT=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_KIRKWOOD=y +CONFIG_SUPPORT_PASSING_ATAGS=y +CONFIG_CMDLINE_TAG=y +CONFIG_INITRD_TAG=y CONFIG_SYS_KWD_CONFIG="board/Marvell/openrd/kwbimage.cfg" CONFIG_TEXT_BASE=0x600000 CONFIG_NR_DRAM_BANKS=2 -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc8012000 CONFIG_TARGET_OPENRD=y CONFIG_BOARD_IS_OPENRD_ULTIMATE=y CONFIG_ENV_SIZE=0x20000 @@ -15,12 +17,10 @@ CONFIG_ENV_OFFSET=0x80000 CONFIG_DEFAULT_DEVICE_TREE="marvell/kirkwood-openrd-ultimate" CONFIG_SYS_LOAD_ADDR=0x800000 CONFIG_IDENT_STRING="\nOpenRD-Ultimate" -# CONFIG_SYS_MALLOC_F is not set CONFIG_HAS_BOARD_SIZE_LIMIT=y CONFIG_BOARD_SIZE_LIMIT=524288 +CONFIG_BOOTSTD_FULL=y CONFIG_BOOTDELAY=3 -CONFIG_USE_BOOTCOMMAND=y -CONFIG_BOOTCOMMAND="${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;" CONFIG_USE_PREBOOT=y CONFIG_LOGLEVEL=2 # CONFIG_DISPLAY_BOARDINFO is not set @@ -31,23 +31,17 @@ CONFIG_CMD_MMC=y CONFIG_CMD_NAND=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_JFFS2=y CONFIG_CMD_MTDPARTS=y CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd" CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000@0x000000(uboot),0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs)" CONFIG_CMD_UBI=y -CONFIG_ISO_PARTITION=y CONFIG_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y CONFIG_ENV_IS_IN_NAND=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_NETCONSOLE=y CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SYS_ATA_STRIDE=4 CONFIG_SYS_ATA_DATA_OFFSET=0x100 CONFIG_SYS_ATA_REG_OFFSET=0x100 @@ -60,7 +54,5 @@ CONFIG_MTD=y CONFIG_MTD_RAW_NAND=y CONFIG_MVGBE=y CONFIG_MII=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SYS_NS16550_REG_SIZE=-4 CONFIG_USB=y CONFIG_USB_EHCI_HCD=y diff --git a/include/configs/openrd.h b/include/configs/openrd.h index 1e6b16b4e7..f91e62a2e4 100644 --- a/include/configs/openrd.h +++ b/include/configs/openrd.h @@ -15,22 +15,4 @@ #include "mv-common.h" -/* - * Environment variables configurations - */ -/* - * max 4k env size is enough, but in case of nand - * it has to be rounded to sector size - */ - -/* - * Default environment variables - */ - -#define CFG_EXTRA_ENV_SETTINGS "x_bootargs=console=ttyS0,115200 " \ - CONFIG_MTDPARTS_DEFAULT " rw ubi.mtd=2,2048\0" \ - "x_bootcmd_kernel=nand read 0x6400000 0x100000 0x300000\0" \ - "x_bootcmd_usb=usb start\0" \ - "x_bootargs_root=root=ubi0:rootfs rootfstype=ubifs\0" - #endif /* _CONFIG_OPENRD_BASE_H */ -- 2.39.5

2 2

[PATCH 00/16] EFI: ti: Enable EFI capsule updates
by Jonathan Humphreys 28 Jan '25

28 Jan '25

Enable on disk capsule updates, which includes defining the firmware components (tiboot3, spl, u-boot) and enabling processing of raw capsule updates. This is enabled for several TI SoC based platforms: AM64, AM62, AM62p, BeaglePlay, J7, and BeagleboneAI. This series also includes enabling seral flash DFU for AM62 and MMC DFU for beagleplay, and adding the sysreset controller node for AM62 to enable system reset. Jonathan Humphreys (16): board: Define GUIDs for firmware images board: am64x: Define capsule update firmware info configs: am64x: Enable EFI capsule update board: j721e: Define capsule update firmware info configs: j721e: Enable EFI capsule update board: beagleplay: Define capsule update firmware info configs: beagleplay: Enable DFU for MMC configs: beagleplay: Enable EFI capsule update board: am62px: Define capsule update firmware info configs: am62px: Enable EFI capsule update configs: am62x: Enable serial flash DFU arm: dts: k3-am625-sk-u-boot: Add sysreset-controller node board: am62x: Define capsule update firmware info configs: am62x: Enable EFI capsule update board: beagleboneai64: Define capsule update firmware info configs: beagleboneai64: Enable EFI capsule update arch/arm/dts/k3-am625-sk-u-boot.dtsi | 9 +++++ board/beagle/beagleboneai64/beagleboneai64.c | 33 +++++++++++++++++ board/beagle/beagleplay/beagleplay.c | 33 +++++++++++++++++ board/ti/am62px/evm.c | 32 +++++++++++++++++ board/ti/am62x/evm.c | 32 +++++++++++++++++ board/ti/am64x/evm.c | 33 +++++++++++++++++ board/ti/j721e/evm.c | 38 ++++++++++++++++++++ configs/am62px_evm_a53_defconfig | 2 ++ configs/am62x_beagleplay_a53_defconfig | 5 +++ configs/am62x_evm_a53_defconfig | 3 ++ configs/am64x_evm_a53_defconfig | 2 ++ configs/j721e_beagleboneai64_a72_defconfig | 2 ++ configs/j721e_evm_a72_defconfig | 2 ++ include/configs/ti_armv7_common.h | 17 +++++++++ 14 files changed, 243 insertions(+) -- 2.34.1

2 17

[PATCH v4 v5 00/10] add support for Enclustra Mercury AA1 SoMs
by Lothar Rubusch 27 Jan '25

27 Jan '25

Introduce the support for three variants of Enclustra's Intel Mercury AA1 (with Intel Arria10) SoMs and additional configs. The DT approach is partly based on dts/upstream, which are (going to be) upstreamed to the linux kernel. Signed-off-by: Lothar Rubusch <l.rubusch(a)gmail.com> --- v4 -> v5: - exclude typo / wording fixes for binman.rst, gdb.rst and binman/entries.rst - implicitely builds using binman v3 -> v4: - fix wrong mail address in v2 and author - update scripts for stdboot and generic load - clean up patch organization (patch 7/10 was malformed and almost empty, added and removed stances,..) - fix binding used for "enclustra,altera_set_storage" - separate u-boot specific part of .dts to a socfpga_arria10_mercury_aa1-u-boot.dtsi file - integrate fpga.itb build with binman in the -u-boot.dtsi file note: 1. due to binman, now the build will need binman build (i.e. requirements) and is build then with "make NO_PYTHON=1" 2. the fpga bitstream files bitstream.core.rbf and bitstream.periph.rbf are generated by a particular Quartus design, so they can't be committed here. This makes the build fail, if build with binman. For testing, thus build with "make CONFIG_BINMAN=n" - fix some typos in binman and gdb documentation (additional patch) v2 -> v3: - update of DT concept to work with dts/upstream - update of DT parts in arch/arm/dts, because of: -- the handoff initialization of the Arria10 SoC -- the fpga loader for the bitstream in the DTS -- the adjustments to access the boot media, from where to load the fpga.itb -- and to mux media for booting, e.g. QSPI off, when booting from MMC - implementation of kconfig options to combine SoM .dtsi file, carrier board .dtsi files, boot-mode parts, and so on resulting in a single .dts file located in arch/arm/dts because of the above mentioned reasons - adjustents to (better) satisfy dtb checks - updated MAINTAINERS - updated documentation - update to use standard boot and environment as only environment, removal of explicit variables and environment files - removal of duplicate codes - cleanup and implement altera_set_storage (boot media switch command in u-boot shell) based on DM - fix spansion flash access to allow flashing from off the u-boot shell, this patch was already presented separately, the fix is actively needed for the AA1 SoM - sort lists in several files alfabetically - update boot commands using && instead of ; v1 -> v2: - removal si5338 driver - removal si5338 driver usage - rename .c file for the boot cmd, build conditionally - add separate .c file for late boot init to read MAC address from eeprom - keep DT approach for u-boot under discussion - fix issues in doc - update MAINTAINERS to cover doc --- Lothar Rubusch (10): doc: board: enclustra: add Enclustra Mercury+ AA1 ARM: socfpga: add Mercury+ AA1 SoM support ARM: dts: socfpga: add Mercury+ AA1 for u-boot dts ARM: socfpga: add Enclustra storage switch ARM: socfpga: add Mercury+ AA1 boot scripts ARM: socfpga: AA1: support MAC from secure eeprom misc: atsha204a: update kconfig description ARM: dts: arria10: update according to DTSpec ARM: socfpga: update function call to modern API ARM: socfpga: apply binman approach to fpga parts arch/arm/dts/socfpga_arria10.dtsi | 42 ++- ..._arria10_enclustra_mercury_aa1-u-boot.dtsi | 89 +++++ .../socfpga_arria10_enclustra_mercury_aa1.dts | 62 ++++ .../socfpga_arria10_mercury_aa1-u-boot.dtsi | 19 ++ .../dts/socfpga_arria10_mercury_aa1_handoff.h | 305 ++++++++++++++++++ arch/arm/mach-socfpga/Kconfig | 10 + arch/arm/mach-socfpga/misc_arria10.c | 2 - board/enclustra/bootscripts/qspi-aa1.cmd | 12 + board/enclustra/bootscripts/sd-aa1.cmd | 9 + board/enclustra/common/Kconfig | 25 ++ board/enclustra/common/Makefile | 7 + board/enclustra/common/enclustra_mac.h | 48 +++ board/enclustra/common/mac_atsha204.c | 102 ++++++ board/enclustra/common/mac_common.c | 52 +++ board/enclustra/common/mac_ds28.c | 93 ++++++ board/enclustra/mercury_aa1/Kconfig | 52 +++ board/enclustra/mercury_aa1/MAINTAINERS | 12 + board/enclustra/mercury_aa1/Makefile | 10 + .../mercury_aa1/aa1_board_late_init.c | 17 + .../mercury_aa1/aa1_set_storage_cmd.c | 190 +++++++++++ .../socfpga_enclustra_mercury_aa1_defconfig | 86 +++++ doc/board/enclustra/index.rst | 9 + doc/board/enclustra/mercury-aa1.rst | 230 +++++++++++++ doc/board/index.rst | 1 + drivers/misc/Kconfig | 2 +- include/configs/socfpga_mercury_aa1.h | 23 ++ 26 files changed, 1497 insertions(+), 12 deletions(-) create mode 100644 arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1-u-boot.dtsi create mode 100644 arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1.dts create mode 100644 arch/arm/dts/socfpga_arria10_mercury_aa1_handoff.h create mode 100644 board/enclustra/bootscripts/qspi-aa1.cmd create mode 100644 board/enclustra/bootscripts/sd-aa1.cmd create mode 100644 board/enclustra/common/Kconfig create mode 100644 board/enclustra/common/Makefile create mode 100644 board/enclustra/common/enclustra_mac.h create mode 100644 board/enclustra/common/mac_atsha204.c create mode 100644 board/enclustra/common/mac_common.c create mode 100644 board/enclustra/common/mac_ds28.c create mode 100644 board/enclustra/mercury_aa1/Kconfig create mode 100644 board/enclustra/mercury_aa1/MAINTAINERS create mode 100644 board/enclustra/mercury_aa1/Makefile create mode 100644 board/enclustra/mercury_aa1/aa1_board_late_init.c create mode 100644 board/enclustra/mercury_aa1/aa1_set_storage_cmd.c create mode 100644 configs/socfpga_enclustra_mercury_aa1_defconfig create mode 100644 doc/board/enclustra/index.rst create mode 100644 doc/board/enclustra/mercury-aa1.rst create mode 100644 include/configs/socfpga_mercury_aa1.h -- 2.39.2

2 12

[PATCH v4 00/11] add support for Enclustra Mercury AA1 SoMs
by Lothar Rubusch 27 Jan '25

27 Jan '25

Introduce the support for three variants of Enclustra's Intel Mercury AA1 (with Intel Arria10) SoMs and additional configs. The DT approach is partly based on dts/upstream, which are (going to be) upstreamed to the linux kernel. Signed-off-by: Lothar Rubusch <l.rubusch(a)gmail.com> --- v3 -> v4: - fix wrong mail address in v2 and author - update scripts for stdboot and generic load - clean up patch organization (patch 7/10 was malformed and almost empty, added and removed stances,..) - fix binding used for "enclustra,altera_set_storage" - separate u-boot specific part of .dts to a socfpga_arria10_mercury_aa1-u-boot.dtsi file - integrate fpga.itb build with binman in the -u-boot.dtsi file note: 1. due to binman, now the build will need binman build (i.e. requirements) and is build then with "make NO_PYTHON=1" 2. the fpga bitstream files bitstream.core.rbf and bitstream.periph.rbf are generated by a particular Quartus design, so they can't be committed here. This makes the build fail, if build with binman. For testing, thus build with "make CONFIG_BINMAN=n" - fix some typos in binman and gdb documentation (additional patch) v2 -> v3: - update of DT concept to work with dts/upstream - update of DT parts in arch/arm/dts, because of: -- the handoff initialization of the Arria10 SoC -- the fpga loader for the bitstream in the DTS -- the adjustments to access the boot media, from where to load the fpga.itb -- and to mux media for booting, e.g. QSPI off, when booting from MMC - implementation of kconfig options to combine SoM .dtsi file, carrier board .dtsi files, boot-mode parts, and so on resulting in a single .dts file located in arch/arm/dts because of the above mentioned reasons - adjustents to (better) satisfy dtb checks - updated MAINTAINERS - updated documentation - update to use standard boot and environment as only environment, removal of explicit variables and environment files - removal of duplicate codes - cleanup and implement altera_set_storage (boot media switch command in u-boot shell) based on DM - fix spansion flash access to allow flashing from off the u-boot shell, this patch was already presented separately, the fix is actively needed for the AA1 SoM - sort lists in several files alfabetically - update boot commands using && instead of ; v1 -> v2: - removal si5338 driver - removal si5338 driver usage - rename .c file for the boot cmd, build conditionally - add separate .c file for late boot init to read MAC address from eeprom - keep DT approach for u-boot under discussion - fix issues in doc - update MAINTAINERS to cover doc --- Lothar Rubusch (11): doc: board: enclustra: add Enclustra Mercury+ AA1 ARM: socfpga: add Mercury+ AA1 SoM support ARM: dts: socfpga: add Mercury+ AA1 for u-boot dts ARM: socfpga: add Enclustra storage switch ARM: socfpga: add Mercury+ AA1 boot scripts ARM: socfpga: AA1: support MAC from secure eeprom misc: atsha204a: update kconfig description ARM: dts: arria10: update according to DTSpec ARM: socfpga: update function call to modern API ARM: socfpga: apply binman approach to fpga parts doc: develop: orthographic delights arch/arm/dts/socfpga_arria10.dtsi | 42 ++- ..._arria10_enclustra_mercury_aa1-u-boot.dtsi | 89 +++++ .../socfpga_arria10_enclustra_mercury_aa1.dts | 62 ++++ .../socfpga_arria10_mercury_aa1-u-boot.dtsi | 19 ++ .../dts/socfpga_arria10_mercury_aa1_handoff.h | 305 ++++++++++++++++++ arch/arm/mach-socfpga/Kconfig | 10 + arch/arm/mach-socfpga/misc_arria10.c | 2 - board/enclustra/bootscripts/qspi-aa1.cmd | 12 + board/enclustra/bootscripts/sd-aa1.cmd | 9 + board/enclustra/common/Kconfig | 25 ++ board/enclustra/common/Makefile | 7 + board/enclustra/common/enclustra_mac.h | 48 +++ board/enclustra/common/mac_atsha204.c | 102 ++++++ board/enclustra/common/mac_common.c | 52 +++ board/enclustra/common/mac_ds28.c | 93 ++++++ board/enclustra/mercury_aa1/Kconfig | 52 +++ board/enclustra/mercury_aa1/MAINTAINERS | 12 + board/enclustra/mercury_aa1/Makefile | 10 + .../mercury_aa1/aa1_board_late_init.c | 17 + .../mercury_aa1/aa1_set_storage_cmd.c | 190 +++++++++++ .../socfpga_enclustra_mercury_aa1_defconfig | 86 +++++ doc/board/enclustra/index.rst | 9 + doc/board/enclustra/mercury-aa1.rst | 230 +++++++++++++ doc/board/index.rst | 1 + doc/develop/gdb.rst | 2 +- drivers/misc/Kconfig | 2 +- include/configs/socfpga_mercury_aa1.h | 23 ++ tools/binman/binman.rst | 4 +- tools/binman/entries.rst | 22 +- 29 files changed, 1511 insertions(+), 26 deletions(-) create mode 100644 arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1-u-boot.dtsi create mode 100644 arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1.dts create mode 100644 arch/arm/dts/socfpga_arria10_mercury_aa1_handoff.h create mode 100644 board/enclustra/bootscripts/qspi-aa1.cmd create mode 100644 board/enclustra/bootscripts/sd-aa1.cmd create mode 100644 board/enclustra/common/Kconfig create mode 100644 board/enclustra/common/Makefile create mode 100644 board/enclustra/common/enclustra_mac.h create mode 100644 board/enclustra/common/mac_atsha204.c create mode 100644 board/enclustra/common/mac_common.c create mode 100644 board/enclustra/common/mac_ds28.c create mode 100644 board/enclustra/mercury_aa1/Kconfig create mode 100644 board/enclustra/mercury_aa1/MAINTAINERS create mode 100644 board/enclustra/mercury_aa1/Makefile create mode 100644 board/enclustra/mercury_aa1/aa1_board_late_init.c create mode 100644 board/enclustra/mercury_aa1/aa1_set_storage_cmd.c create mode 100644 configs/socfpga_enclustra_mercury_aa1_defconfig create mode 100644 doc/board/enclustra/index.rst create mode 100644 doc/board/enclustra/mercury-aa1.rst create mode 100644 include/configs/socfpga_mercury_aa1.h -- 2.25.1

3 14

Git commit failed with mbedtls/framework
by Tony Dinh 27 Jan '25

27 Jan '25

Hi Tom, I am on 2025.01-rc2, and I am trying to commit some files. The error seems to indicate this framework directory might need some modification. Did I miss something? error: 'lib/mbedtls/external/mbedtls/framework' does not have a commit checked out fatal: updating files failed All the best, Tony

4 20

[PATCH v2] mmc: Remove alignment hole for cmdidx in struct mmc_cmd
by Jonas Karlman 27 Jan '25

27 Jan '25

The alignment hole caused by cmdidx in struct mmc_cmd cause strange issues together with the peephole2 optimization on Amlogic SoCs. Following was observed while working on SPL support for Amlogic SoCs. sd_get_capabilities() normally issue a CMD55 followed by a CMD51. However, on at least Amlogic S905 (Cortex-A53) and S905X3 (Cortex-A55), CMD55 was instead followed by CMD8 (and a few reties) in SPL. Code from the call site: cmd.cmdidx = SD_CMD_APP_SEND_SCR; // 51 ... data.blocksize = 8; ... err = mmc_send_cmd_retry(mmc, &cmd, &data, 3); Running the code with MMC_TRACE enabled shows: CMD_SEND:55 ARG 0x50480000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:8 ARG 0x00000000 RET -110 Removing the alignment hole by changing cmdidx from ushort to uint or building with -fno-peephole2 flag seem to resolve this issue. CMD_SEND:55 ARG 0x50480000 MMC_RSP_R1,5,6,7 0x00000920 CMD_SEND:51 ARG 0x00000000 MMC_RSP_R1,5,6,7 0x00000920 Same issue was observed building U-Boot with gcc 8 - 13. Remove this alignment hole by changing cmdidx from ushort to uint. Signed-off-by: Jonas Karlman <jonas(a)kwiboo.se> --- Changes in v2: - Drop use of -fno-peephole2 flag Link to RFC: https://patchwork.ozlabs.org/patch/1841495/ --- include/mmc.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/mmc.h b/include/mmc.h index 1022db3ffa7c..031ea0fb3545 100644 --- a/include/mmc.h +++ b/include/mmc.h @@ -413,7 +413,7 @@ struct mmc_cid { }; struct mmc_cmd { - ushort cmdidx; + uint cmdidx; uint resp_type; uint cmdarg; uint response[4]; -- 2.43.0

4 5

[PATCH v3 00/19] bootstd: Support recording images
by Simon Glass 25 Jan '25

25 Jan '25

This series provides a way to keep track of the images used in bootstd, including the type of each image. At present this is sort-of handled by struct bootflow but in quite an ad-hoc way. The structure has become quite large and is hard to query. Future work will be able to reduce its size. Ultimately the 'bootflow info' command may change to also show images as a list, but that is left for later, as this series is already fairly long. So for now, just introduce the concept and adjust bootstd to use it, with a simple command to list the images. This series includes various alist enhancements, to make use of this new data structure a little easier. Changes in v3: - Add a helper in bootflow - Add a new patch supporting ad-hoc bootflows - Add new patch to export bootdev_get_from_blk() - Add new patch to record loaded files in an ad-hoc bootflow - Update bootstd_add_bootflow() to return the element number - Use the helper function Changes in v2: - Add an image type extension in bootflow.h - Change the tag to bootmeth_efi - Drop patches already applied - Drop patches which add new image types - Update to use a new image-type enum in bootflow.h - Use the word 'feature' instead of 'hack' Simon Glass (19): bootstd: Move bootflow-adding to bootstd bootstd: Move bootflow-clearing to bootstd bootstd: Add a function to get bootstd only if available bootstd: Drop the bootdev-specific list of bootflows bootstd: Move the bootflow list into an alist bootstd: Maintain a list of images bootstd: Update bootmeth_alloc_file() to record images boot: pxe: Drop the duplicate comment on get_pxe_file() bootmeth_efi: Simplify reading files by using the common function bootmeth: Update the read_file() method to include a type bootmeth_efi: Check the filename-allocation in the network path boot: Update extlinux pxe_getfile_func() to include type boot: Update pxe bootmeth to record images Update bootmeth_alloc_other() to record images bootstd: Update cros bootmeth to record images bootstd: Add a simple command to list images bootstd: Export bootdev_get_from_blk() bootstd: Add the concept of an ad-hoc bootflow fs: Record loaded files in an ad-hoc bootflow boot/bootdev-uclass.c | 78 ++++++------------- boot/bootflow.c | 77 +++++++++++++++---- boot/bootmeth-uclass.c | 29 +++++-- boot/bootmeth_android.c | 3 +- boot/bootmeth_cros.c | 17 ++++- boot/bootmeth_efi.c | 16 ++-- boot/bootmeth_efi_mgr.c | 3 +- boot/bootmeth_extlinux.c | 7 +- boot/bootmeth_pxe.c | 10 ++- boot/bootmeth_qfw.c | 3 +- boot/bootmeth_sandbox.c | 3 +- boot/bootmeth_script.c | 7 +- boot/bootstd-uclass.c | 104 +++++++++++++++++++++++-- boot/pxe_utils.c | 36 ++++----- boot/vbe_simple.c | 5 +- cmd/Kconfig | 9 +++ cmd/Makefile | 1 + cmd/bootdev.c | 2 +- cmd/bootflow.c | 11 +-- cmd/bootstd.c | 65 ++++++++++++++++ cmd/pxe.c | 2 +- cmd/sysboot.c | 6 +- doc/develop/bootstd/overview.rst | 24 +++++- doc/usage/cmd/bootstd.rst | 79 +++++++++++++++++++ doc/usage/index.rst | 1 + fs/fs.c | 15 ++++ include/bootdev.h | 36 +++------ include/bootflow.h | 88 ++++++++++++++++++--- include/bootmeth.h | 22 ++++-- include/bootstd.h | 69 ++++++++++++++++- include/pxe_utils.h | 14 +++- test/boot/bootflow.c | 126 +++++++++++++++++++++++++++++++ test/py/tests/test_ut.py | 3 +- 33 files changed, 788 insertions(+), 183 deletions(-) create mode 100644 cmd/bootstd.c create mode 100644 doc/usage/cmd/bootstd.rst -- 2.34.1

4 40

[PATCH] phy: qcom: add QMP PCIe PHY driver
by Neil Armstrong 22 Jan '25

22 Jan '25

Add support for the PCIe QMP PHY on the SM8550, SM8650 and x1e80100 SoCs. The driver is based on the Linux phy/qualcomm/phy-qcom-qmp-pcie.c driver and adapted to U-Boot. Signed-off-by: Neil Armstrong <neil.armstrong(a)linaro.org> --- drivers/phy/qcom/Kconfig | 6 + drivers/phy/qcom/Makefile | 1 + drivers/phy/qcom/phy-qcom-qmp-pcie-qhp.h | 123 +++ drivers/phy/qcom/phy-qcom-qmp-pcie.c | 1131 ++++++++++++++++++++ drivers/phy/qcom/phy-qcom-qmp-pcs-misc-v3.h | 17 + drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4.h | 72 ++ drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4_20.h | 19 + drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5.h | 17 + drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5_20.h | 23 + drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6.h | 17 + drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6_20.h | 25 + drivers/phy/qcom/phy-qcom-qmp-pcs-v5.h | 34 + drivers/phy/qcom/phy-qcom-qmp-pcs-v6.h | 32 + drivers/phy/qcom/phy-qcom-qmp-pcs-v6_20.h | 19 + drivers/phy/qcom/phy-qcom-qmp-qserdes-ln-shrd-v6.h | 32 + drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6.h | 83 ++ drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6_20.h | 51 + 17 files changed, 1702 insertions(+) diff --git a/drivers/phy/qcom/Kconfig b/drivers/phy/qcom/Kconfig index 5c77203d606d2e7463be808d76a88ce26dbaa9e2..61e5e2fca413b4706d9b8ff25cea3fb5e20a5da6 100644 --- a/drivers/phy/qcom/Kconfig +++ b/drivers/phy/qcom/Kconfig @@ -12,6 +12,12 @@ config PHY_QCOM_IPQ4019_USB help Support for the USB PHY-s on Qualcomm IPQ40xx SoC-s. +config PHY_QCOM_QMP_PCIE + tristate "Qualcomm QMP PCIe PHY driver" + depends on PHY && ARCH_SNAPDRAGON + help + Enable this to support the PCIe QMP PHY on various Qualcomm chipsets. + config PHY_QCOM_QMP_UFS tristate "Qualcomm QMP UFS PHY driver" depends on PHY && ARCH_SNAPDRAGON diff --git a/drivers/phy/qcom/Makefile b/drivers/phy/qcom/Makefile index dc3ed492696f36340d5fe901d45d6f8678da86c3..1c4e7d8d39178d6d604092f9d9890f17c03d963d 100644 --- a/drivers/phy/qcom/Makefile +++ b/drivers/phy/qcom/Makefile @@ -1,5 +1,6 @@ obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o obj-$(CONFIG_MSM8916_USB_PHY) += msm8916-usbh-phy.o +obj-$(CONFIG_PHY_QCOM_QMP_PCIE) += phy-qcom-qmp-pcie.o obj-$(CONFIG_PHY_QCOM_QMP_UFS) += phy-qcom-qmp-ufs.o obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o obj-$(CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2) += phy-qcom-snps-femto-v2.o diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcie-qhp.h b/drivers/phy/qcom/phy-qcom-qmp-pcie-qhp.h new file mode 100644 index 0000000000000000000000000000000000000000..e4a4d2cd85ebde614fbb4c04afeea22eb7131aaa --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcie-qhp.h @@ -0,0 +1,123 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCIE_QHP_H_ +#define QCOM_PHY_QMP_PCIE_QHP_H_ + +/* PCIE GEN3 COM registers */ +#define PCIE_GEN3_QHP_COM_SSC_EN_CENTER 0x14 +#define PCIE_GEN3_QHP_COM_SSC_PER1 0x20 +#define PCIE_GEN3_QHP_COM_SSC_PER2 0x24 +#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE1 0x28 +#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE2 0x2c +#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE1_MODE1 0x34 +#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE2_MODE1 0x38 +#define PCIE_GEN3_QHP_COM_BIAS_EN_CKBUFLR_EN 0x54 +#define PCIE_GEN3_QHP_COM_CLK_ENABLE1 0x58 +#define PCIE_GEN3_QHP_COM_LOCK_CMP1_MODE0 0x6c +#define PCIE_GEN3_QHP_COM_LOCK_CMP2_MODE0 0x70 +#define PCIE_GEN3_QHP_COM_LOCK_CMP1_MODE1 0x78 +#define PCIE_GEN3_QHP_COM_LOCK_CMP2_MODE1 0x7c +#define PCIE_GEN3_QHP_COM_BGV_TRIM 0x98 +#define PCIE_GEN3_QHP_COM_CP_CTRL_MODE0 0xb4 +#define PCIE_GEN3_QHP_COM_CP_CTRL_MODE1 0xb8 +#define PCIE_GEN3_QHP_COM_PLL_RCTRL_MODE0 0xc0 +#define PCIE_GEN3_QHP_COM_PLL_RCTRL_MODE1 0xc4 +#define PCIE_GEN3_QHP_COM_PLL_CCTRL_MODE0 0xcc +#define PCIE_GEN3_QHP_COM_PLL_CCTRL_MODE1 0xd0 +#define PCIE_GEN3_QHP_COM_SYSCLK_EN_SEL 0xdc +#define PCIE_GEN3_QHP_COM_RESTRIM_CTRL2 0xf0 +#define PCIE_GEN3_QHP_COM_LOCK_CMP_EN 0xf8 +#define PCIE_GEN3_QHP_COM_DEC_START_MODE0 0x100 +#define PCIE_GEN3_QHP_COM_DEC_START_MODE1 0x108 +#define PCIE_GEN3_QHP_COM_DIV_FRAC_START1_MODE0 0x11c +#define PCIE_GEN3_QHP_COM_DIV_FRAC_START2_MODE0 0x120 +#define PCIE_GEN3_QHP_COM_DIV_FRAC_START3_MODE0 0x124 +#define PCIE_GEN3_QHP_COM_DIV_FRAC_START1_MODE1 0x128 +#define PCIE_GEN3_QHP_COM_DIV_FRAC_START2_MODE1 0x12c +#define PCIE_GEN3_QHP_COM_DIV_FRAC_START3_MODE1 0x130 +#define PCIE_GEN3_QHP_COM_INTEGLOOP_GAIN0_MODE0 0x150 +#define PCIE_GEN3_QHP_COM_INTEGLOOP_GAIN0_MODE1 0x158 +#define PCIE_GEN3_QHP_COM_VCO_TUNE_MAP 0x178 +#define PCIE_GEN3_QHP_COM_BG_CTRL 0x1c8 +#define PCIE_GEN3_QHP_COM_CLK_SELECT 0x1cc +#define PCIE_GEN3_QHP_COM_HSCLK_SEL1 0x1d0 +#define PCIE_GEN3_QHP_COM_CORECLK_DIV 0x1e0 +#define PCIE_GEN3_QHP_COM_CORE_CLK_EN 0x1e8 +#define PCIE_GEN3_QHP_COM_CMN_CONFIG 0x1f0 +#define PCIE_GEN3_QHP_COM_SVS_MODE_CLK_SEL 0x1fc +#define PCIE_GEN3_QHP_COM_CORECLK_DIV_MODE1 0x21c +#define PCIE_GEN3_QHP_COM_CMN_MODE 0x224 +#define PCIE_GEN3_QHP_COM_VREGCLK_DIV1 0x228 +#define PCIE_GEN3_QHP_COM_VREGCLK_DIV2 0x22c + +/* PCIE GEN3 QHP Lane registers */ +#define PCIE_GEN3_QHP_L0_DRVR_CTRL0 0xc +#define PCIE_GEN3_QHP_L0_DRVR_CTRL1 0x10 +#define PCIE_GEN3_QHP_L0_DRVR_CTRL2 0x14 +#define PCIE_GEN3_QHP_L0_DRVR_TAP_EN 0x18 +#define PCIE_GEN3_QHP_L0_TX_BAND_MODE 0x60 +#define PCIE_GEN3_QHP_L0_LANE_MODE 0x64 +#define PCIE_GEN3_QHP_L0_PARALLEL_RATE 0x7c +#define PCIE_GEN3_QHP_L0_CML_CTRL_MODE0 0xc0 +#define PCIE_GEN3_QHP_L0_CML_CTRL_MODE1 0xc4 +#define PCIE_GEN3_QHP_L0_CML_CTRL_MODE2 0xc8 +#define PCIE_GEN3_QHP_L0_PREAMP_CTRL_MODE1 0xd0 +#define PCIE_GEN3_QHP_L0_PREAMP_CTRL_MODE2 0xd4 +#define PCIE_GEN3_QHP_L0_MIXER_CTRL_MODE0 0xd8 +#define PCIE_GEN3_QHP_L0_MIXER_CTRL_MODE1 0xdc +#define PCIE_GEN3_QHP_L0_MIXER_CTRL_MODE2 0xe0 +#define PCIE_GEN3_QHP_L0_CTLE_THRESH_DFE 0xfc +#define PCIE_GEN3_QHP_L0_CGA_THRESH_DFE 0x100 +#define PCIE_GEN3_QHP_L0_RXENGINE_EN0 0x108 +#define PCIE_GEN3_QHP_L0_CTLE_TRAIN_TIME 0x114 +#define PCIE_GEN3_QHP_L0_CTLE_DFE_OVRLP_TIME 0x118 +#define PCIE_GEN3_QHP_L0_DFE_REFRESH_TIME 0x11c +#define PCIE_GEN3_QHP_L0_DFE_ENABLE_TIME 0x120 +#define PCIE_GEN3_QHP_L0_VGA_GAIN 0x124 +#define PCIE_GEN3_QHP_L0_DFE_GAIN 0x128 +#define PCIE_GEN3_QHP_L0_EQ_GAIN 0x130 +#define PCIE_GEN3_QHP_L0_OFFSET_GAIN 0x134 +#define PCIE_GEN3_QHP_L0_PRE_GAIN 0x138 +#define PCIE_GEN3_QHP_L0_VGA_INITVAL 0x13c +#define PCIE_GEN3_QHP_L0_EQ_INTVAL 0x154 +#define PCIE_GEN3_QHP_L0_EDAC_INITVAL 0x160 +#define PCIE_GEN3_QHP_L0_RXEQ_INITB0 0x168 +#define PCIE_GEN3_QHP_L0_RXEQ_INITB1 0x16c +#define PCIE_GEN3_QHP_L0_RCVRDONE_THRESH1 0x178 +#define PCIE_GEN3_QHP_L0_RXEQ_CTRL 0x180 +#define PCIE_GEN3_QHP_L0_UCDR_FO_GAIN_MODE0 0x184 +#define PCIE_GEN3_QHP_L0_UCDR_FO_GAIN_MODE1 0x188 +#define PCIE_GEN3_QHP_L0_UCDR_FO_GAIN_MODE2 0x18c +#define PCIE_GEN3_QHP_L0_UCDR_SO_GAIN_MODE0 0x190 +#define PCIE_GEN3_QHP_L0_UCDR_SO_GAIN_MODE1 0x194 +#define PCIE_GEN3_QHP_L0_UCDR_SO_GAIN_MODE2 0x198 +#define PCIE_GEN3_QHP_L0_UCDR_SO_CONFIG 0x19c +#define PCIE_GEN3_QHP_L0_RX_BAND 0x1a4 +#define PCIE_GEN3_QHP_L0_RX_RCVR_PATH1_MODE0 0x1c0 +#define PCIE_GEN3_QHP_L0_RX_RCVR_PATH1_MODE1 0x1c4 +#define PCIE_GEN3_QHP_L0_RX_RCVR_PATH1_MODE2 0x1c8 +#define PCIE_GEN3_QHP_L0_SIGDET_ENABLES 0x230 +#define PCIE_GEN3_QHP_L0_SIGDET_CNTRL 0x234 +#define PCIE_GEN3_QHP_L0_SIGDET_DEGLITCH_CNTRL 0x238 +#define PCIE_GEN3_QHP_L0_DCC_GAIN 0x2a4 +#define PCIE_GEN3_QHP_L0_RSM_START 0x2a8 +#define PCIE_GEN3_QHP_L0_RX_EN_SIGNAL 0x2ac +#define PCIE_GEN3_QHP_L0_PSM_RX_EN_CAL 0x2b0 +#define PCIE_GEN3_QHP_L0_RX_MISC_CNTRL0 0x2b8 +#define PCIE_GEN3_QHP_L0_TS0_TIMER 0x2c0 +#define PCIE_GEN3_QHP_L0_DLL_HIGHDATARATE 0x2c4 +#define PCIE_GEN3_QHP_L0_RX_RESETCODE_OFFSET 0x2cc + +/* PCIE GEN3 PCS registers */ +#define PCIE_GEN3_QHP_PHY_TXMGN_MAIN_V0_M3P5DB 0x2c +#define PCIE_GEN3_QHP_PHY_TXMGN_POST_V0_M3P5DB 0x40 +#define PCIE_GEN3_QHP_PHY_TXMGN_MAIN_V0_M6DB 0x54 +#define PCIE_GEN3_QHP_PHY_TXMGN_POST_V0_M6DB 0x68 +#define PCIE_GEN3_QHP_PHY_POWER_STATE_CONFIG 0x15c +#define PCIE_GEN3_QHP_PHY_POWER_STATE_CONFIG5 0x16c +#define PCIE_GEN3_QHP_PHY_PCS_TX_RX_CONFIG 0x174 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcie.c b/drivers/phy/qcom/phy-qcom-qmp-pcie.c new file mode 100644 index 0000000000000000000000000000000000000000..2f6ff259b353dbd92303d5db79e6092385911c69 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcie.c @@ -0,0 +1,1131 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2023 Bhupesh Sharma <bhupesh.sharma(a)linaro.org> + * + * Based on Linux driver + */ + +#include <clk.h> +#include <clk-uclass.h> +#include <dm.h> +#include <dm/device_compat.h> +#include <dm/devres.h> +#include <generic-phy.h> +#include <malloc.h> +#include <reset.h> +#include <power/regulator.h> + +#include <asm/io.h> +#include <linux/bitops.h> +#include <linux/clk-provider.h> +#include <linux/delay.h> +#include <linux/iopoll.h> +#include <linux/ioport.h> + +#include "phy-qcom-qmp.h" +#include "phy-qcom-qmp-pcs-misc-v3.h" +#include "phy-qcom-qmp-pcs-v5.h" +#include "phy-qcom-qmp-pcs-v6.h" +#include "phy-qcom-qmp-pcs-v6_20.h" +#include "phy-qcom-qmp-pcs-pcie-v6.h" +#include "phy-qcom-qmp-pcs-pcie-v6_20.h" +#include "phy-qcom-qmp-pcie-qhp.h" +#include "phy-qcom-qmp-qserdes-com-v6.h" +#include "phy-qcom-qmp-qserdes-txrx-v6.h" +#include "phy-qcom-qmp-qserdes-txrx-v6_20.h" +#include "phy-qcom-qmp-qserdes-ln-shrd-v6.h" + +/* QPHY_SW_RESET bit */ +#define SW_RESET BIT(0) +/* QPHY_POWER_DOWN_CONTROL */ +#define SW_PWRDN BIT(0) +#define REFCLK_DRV_DSBL BIT(1) +/* QPHY_START_CONTROL bits */ +#define SERDES_START BIT(0) +#define PCS_START BIT(1) +/* QPHY_PCS_READY_STATUS bit */ +#define PCS_READY BIT(0) + +/* QPHY_PCS_STATUS bit */ +#define PHYSTATUS BIT(6) +#define PHYSTATUS_4_20 BIT(7) + +#define PHY_INIT_COMPLETE_TIMEOUT (200 * 10000) + +#define NUM_SUPPLIES 3 + +struct qmp_pcie_init_tbl { + unsigned int offset; + unsigned int val; + /* + * mask of lanes for which this register is written + * for cases when second lane needs different values + */ + u8 lane_mask; +}; + +#define QMP_PHY_INIT_CFG(o, v) \ + { \ + .offset = o, \ + .val = v, \ + .lane_mask = 0xff, \ + } + +#define QMP_PHY_INIT_CFG_LANE(o, v, l) \ + { \ + .offset = o, \ + .val = v, \ + .lane_mask = l, \ + } + +/* set of registers with offsets different per-PHY */ +enum qphy_reg_layout { + /* PCS registers */ + QPHY_SW_RESET, + QPHY_START_CTRL, + QPHY_PCS_STATUS, + QPHY_PCS_POWER_DOWN_CONTROL, + /* Keep last to ensure regs_layout arrays are properly initialized */ + QPHY_LAYOUT_SIZE +}; + +static const unsigned int pciephy_v5_regs_layout[QPHY_LAYOUT_SIZE] = { + [QPHY_SW_RESET] = QPHY_V5_PCS_SW_RESET, + [QPHY_START_CTRL] = QPHY_V5_PCS_START_CONTROL, + [QPHY_PCS_STATUS] = QPHY_V5_PCS_PCS_STATUS1, + [QPHY_PCS_POWER_DOWN_CONTROL] = QPHY_V5_PCS_POWER_DOWN_CONTROL, +}; + +static const unsigned int pciephy_v6_regs_layout[QPHY_LAYOUT_SIZE] = { + [QPHY_SW_RESET] = QPHY_V6_PCS_SW_RESET, + [QPHY_START_CTRL] = QPHY_V6_PCS_START_CONTROL, + [QPHY_PCS_STATUS] = QPHY_V6_PCS_PCS_STATUS1, + [QPHY_PCS_POWER_DOWN_CONTROL] = QPHY_V6_PCS_POWER_DOWN_CONTROL, +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen3x2_pcie_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x93), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x07), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x42), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x34), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0x55), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0x55), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_ADDITIONAL_MISC_3, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen3x2_pcie_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0x15), + QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_4, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_V6_TX_PI_QEC_CTRL, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x18), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen3x2_pcie_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_GM_CAL, 0x11), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH, 0xbf), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH2, 0xbf), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH3, 0xb7), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_HIGH4, 0xea), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_00_LOW, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH, 0x5c), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH2, 0x9c), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH3, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_HIGH4, 0x89), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_01_LOW, 0xdc), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH, 0x94), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH2, 0x5b), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH3, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_MODE_10_HIGH4, 0x89), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_TX_ADAPT_POST_THRESH, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_FO_GAIN, 0x09), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SO_GAIN, 0x05), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SB2_THRESH1, 0x08), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_UCDR_SB2_THRESH2, 0x08), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_VGA_CAL_CNTRL2, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_SIDGET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_RX_IDAC_TSETTLE_LOW, 0x07), + QMP_PHY_INIT_CFG(QSERDES_V6_RX_SIGDET_CAL_TRIM, 0x08), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen3x2_pcie_pcs_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_V6_PCS_REFGEN_REQ_CONFIG1, 0x05), + QMP_PHY_INIT_CFG(QPHY_V6_PCS_RX_SIGDET_LVL, 0x77), + QMP_PHY_INIT_CFG(QPHY_V6_PCS_RATE_SLEW_CNTRL1, 0x0b), + QMP_PHY_INIT_CFG(QPHY_V6_PCS_EQ_CONFIG2, 0x0f), + QMP_PHY_INIT_CFG(QPHY_V6_PCS_PCS_TX_RX_CONFIG, 0x8c), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen3x2_pcie_pcs_misc_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_EQ_CONFIG1, 0x1e), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_RXEQEVAL_TIME, 0x27), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2, 0x1d), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4, 0x07), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_PCS_PCIE_OSC_DTCT_ACTIONS, 0x00), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen4x2_pcie_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x26), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x68), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0xab), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0xaa), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x12), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_POST_DIV_MUX, 0x40), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x46), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MISC_1, 0x88), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MODE, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_VCO_DC_LEVEL_CTRL, 0x0f), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen4x2_pcie_ln_shrd_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0, 0x12), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1, 0x12), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2, 0xdb), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3, 0x9a), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4, 0x38), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5, 0xb6), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6, 0x64), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_SUMMER_CAL_SPD_MODE, 0x5b), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen4x2_pcie_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX, 0x1d), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_3, 0x51), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN, 0x34), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen4x2_pcie_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_GAIN_RATE_2, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_PI_CONTROLS, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_CAL_CTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET, 0x7c), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_3, 0x05), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_TX_ADPT_CTRL, 0x10), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_GM_CAL, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_PHPRE_CTRL, 0x20), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x30), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32, 0x09), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B0, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B1, 0xb3), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B2, 0x58), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B3, 0x9a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B4, 0x26), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B5, 0xb6), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B6, 0xee), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B0, 0xdb), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B1, 0xdb), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B2, 0xa0), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B3, 0xdf), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B4, 0x78), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B5, 0x76), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B6, 0xff), + QMP_PHY_INIT_CFG(QSERDES_V6_20_VGA_CAL_CNTRL1, 0x00), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen4x2_pcie_pcs_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_G12S1_TXDEEMPH_M6DB, 0x17), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_G3S2_PRE_GAIN, 0x2e), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_RX_SIGDET_LVL, 0xcc), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG4, 0x00), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG5, 0x22), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG1, 0x04), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG2, 0x02), +}; + +static const struct qmp_pcie_init_tbl sm8550_qmp_gen4x2_pcie_pcs_misc_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE, 0xc1), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS, 0x00), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG1, 0x16), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G3_RXEQEVAL_TIME, 0x27), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_RXEQEVAL_TIME, 0x27), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG5, 0x02), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN, 0x2e), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1, 0x03), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3, 0x28), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG, 0xc0), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2, 0x1d), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5, 0x0f), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5, 0xf2), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5, 0xf2), +}; + +static const struct qmp_pcie_init_tbl sm8650_qmp_gen4x2_pcie_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_PI_CONTROLS, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_CAL_CTRL2, 0x82), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_3, 0x05), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_GM_CAL, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_PHPRE_CTRL, 0x20), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B0, 0xd3), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B1, 0xd3), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B3, 0x9a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B4, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B5, 0xb6), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B6, 0xee), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B0, 0x23), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B1, 0x9b), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B2, 0x60), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B3, 0xdf), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B4, 0x43), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B5, 0x76), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B6, 0xff), +}; + +static const struct qmp_pcie_init_tbl x1e80100_qmp_gen4x2_pcie_serdes_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE1, 0x26), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE1, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORECLK_DIV_MODE1, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x1a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x68), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE1, 0xab), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE1, 0xaa), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x12), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE1_MODE0, 0xf8), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_STEP_SIZE2_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x36), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CORE_CLK_DIV_MODE0, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START1_MODE0, 0xab), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START2_MODE0, 0xaa), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DIV_FRAC_START3_MODE0, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_BG_TIMER, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_EN_CENTER, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER1, 0x62), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SSC_PER2, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_POST_DIV_MUX, 0x40), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_ENABLE1, 0x90), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYS_CLK_CTRL, 0x82), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0x08), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x46), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CLK_SELECT, 0x34), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CORE_CLK_EN, 0xa0), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MISC_1, 0x88), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_MODE, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_VCO_DC_LEVEL_CTRL, 0x0f), +}; + +static const struct qmp_pcie_init_tbl x1e80100_qmp_gen4x2_pcie_ln_shrd_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1, 0x88), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1, 0x02), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0, 0xd4), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1, 0x12), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2, 0xdb), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3, 0x9a), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4, 0x32), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5, 0xb6), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6, 0x64), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3, 0x1f), + QMP_PHY_INIT_CFG(QSERDES_V6_LN_SHRD_RX_SUMMER_CAL_SPD_MODE, 0x5b), +}; + +static const struct qmp_pcie_init_tbl x1e80100_qmp_gen4x2_pcie_tx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX, 0x1d), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_2, 0x10), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_LANE_MODE_3, 0x51), + QMP_PHY_INIT_CFG(QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN, 0x34), +}; + +static const struct qmp_pcie_init_tbl x1e80100_qmp_gen4x2_pcie_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_GAIN_RATE_2, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_PI_CONTROLS, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_CAL_CTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_BKUP_CTRL1, 0x15), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_2, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_DFE_3, 0x45), + QMP_PHY_INIT_CFG_LANE(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0a, 1), + QMP_PHY_INIT_CFG_LANE(QSERDES_V6_20_RX_VGA_CAL_MAN_VAL, 0x0b, 2), + QMP_PHY_INIT_CFG(QSERDES_V6_20_VGA_CAL_CNTRL1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_GM_CAL, 0x0d), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_SIGDET_ENABLES, 0x1c), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_PHPRE_CTRL, 0x20), + QMP_PHY_INIT_CFG_LANE(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x3a, 1), + QMP_PHY_INIT_CFG_LANE(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38, 2), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32, 0x39), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B0, 0x14), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B1, 0xb3), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B2, 0x58), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B3, 0x9a), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B4, 0x26), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B5, 0xb6), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE2_B6, 0xee), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B0, 0xe4), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B1, 0xa4), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B2, 0x60), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B3, 0xdf), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B4, 0x4b), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B5, 0x76), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_MODE_RATE3_B6, 0xff), + QMP_PHY_INIT_CFG(QSERDES_V6_20_RX_TX_ADPT_CTRL, 0x10), +}; + +static const struct qmp_pcie_init_tbl x1e80100_qmp_gen4x2_pcie_pcs_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_G3S2_PRE_GAIN, 0x2e), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_RX_SIGDET_LVL, 0xcc), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG4, 0x00), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_EQ_CONFIG5, 0x22), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG1, 0x04), + QMP_PHY_INIT_CFG(QPHY_V6_20_PCS_TX_RX_CONFIG2, 0x02), +}; + +static const struct qmp_pcie_init_tbl x1e80100_qmp_gen4x2_pcie_pcs_misc_tbl[] = { + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE, 0xc1), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS, 0x00), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG1, 0x16), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_EQ_CONFIG5, 0x02), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN, 0x2e), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1, 0x03), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3, 0x28), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G3_RXEQEVAL_TIME, 0x27), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_RXEQEVAL_TIME, 0x27), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG, 0xc0), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2, 0x1d), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5, 0x18), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5, 0x7a), + QMP_PHY_INIT_CFG(QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5, 0x8a), +}; + +struct qmp_pcie_offsets { + u16 serdes; + u16 pcs; + u16 pcs_misc; + u16 tx; + u16 rx; + u16 tx2; + u16 rx2; + u16 ln_shrd; +}; + +struct qmp_pcie_cfg_tbls { + /* Init sequence for PHY blocks - serdes, tx, rx, pcs */ + const struct qmp_pcie_init_tbl *serdes; + int serdes_num; + const struct qmp_pcie_init_tbl *tx; + int tx_num; + const struct qmp_pcie_init_tbl *rx; + int rx_num; + const struct qmp_pcie_init_tbl *pcs; + int pcs_num; + const struct qmp_pcie_init_tbl *pcs_misc; + int pcs_misc_num; + const struct qmp_pcie_init_tbl *ln_shrd; + int ln_shrd_num; +}; + +/* struct qmp_pcie_cfg - per-PHY initialization config */ +struct qmp_pcie_cfg { + int lanes; + + const struct qmp_pcie_offsets *offsets; + + /* Main init sequence for PHY blocks - serdes, tx, rx, pcs */ + const struct qmp_pcie_cfg_tbls tbls; + + /* regulators to be requested */ + const char * const *vreg_list; + int num_vregs; + /* resets to be requested */ + const char * const *reset_list; + int num_resets; + + /* array of registers with different offsets */ + const unsigned int *regs; + + unsigned int pwrdn_ctrl; + /* bit offset of PHYSTATUS in QPHY_PCS_STATUS register */ + unsigned int phy_status; + + bool has_nocsr_reset; +}; + +struct qmp_pcie_priv { + struct phy *phy; + + void __iomem *serdes; + void __iomem *pcs; + void __iomem *pcs_misc; + void __iomem *tx; + void __iomem *rx; + void __iomem *tx2; + void __iomem *rx2; + void __iomem *ln_shrd; + + struct clk *clks; + unsigned int clk_count; + + struct clk pipe_clk; + + struct reset_ctl *resets; + unsigned int reset_count; + + struct reset_ctl nocsr_reset; + + struct udevice *vregs[NUM_SUPPLIES]; + unsigned int vreg_count; + + const struct qmp_pcie_cfg *cfg; + struct udevice *dev; +}; + +static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val) +{ + u32 reg; + + reg = readl(base + offset); + reg |= val; + writel(reg, base + offset); + + /* ensure that above write is through */ + readl(base + offset); +} + +static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val) +{ + u32 reg; + + reg = readl(base + offset); + reg &= ~val; + writel(reg, base + offset); + + /* ensure that above write is through */ + readl(base + offset); +} + +/* list of clocks required by phy */ +static const char * const qmp_pciephy_clk_l[] = { + "aux", "cfg_ahb", "ref", "rchng", +}; + +/* list of regulators */ +static const char * const qmp_phy_vreg_l[] = { + "vdda-phy-supply", "vdda-pll-supply", +}; + +static const char * const sm8550_qmp_phy_vreg_l[] = { + "vdda-phy-supply", "vdda-pll-supply", "vdda-qref-supply", +}; + +/* list of resets */ +static const char * const sdm845_pciephy_reset_l[] = { + "phy", +}; + +static const struct qmp_pcie_offsets qmp_pcie_offsets_v5 = { + .serdes = 0, + .pcs = 0x0200, + .pcs_misc = 0x0600, + .tx = 0x0e00, + .rx = 0x1000, + .tx2 = 0x1600, + .rx2 = 0x1800, +}; + +static const struct qmp_pcie_offsets qmp_pcie_offsets_v6_20 = { + .serdes = 0x1000, + .pcs = 0x1200, + .pcs_misc = 0x1400, + .tx = 0x0000, + .rx = 0x0200, + .tx2 = 0x0800, + .rx2 = 0x0a00, + .ln_shrd = 0x0e00, +}; + +static const struct qmp_pcie_cfg sm8550_qmp_gen3x2_pciephy_cfg = { + .lanes = 2, + + .offsets = &qmp_pcie_offsets_v5, + + .tbls = { + .serdes = sm8550_qmp_gen3x2_pcie_serdes_tbl, + .serdes_num = ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_serdes_tbl), + .tx = sm8550_qmp_gen3x2_pcie_tx_tbl, + .tx_num = ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_tx_tbl), + .rx = sm8550_qmp_gen3x2_pcie_rx_tbl, + .rx_num = ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_rx_tbl), + .pcs = sm8550_qmp_gen3x2_pcie_pcs_tbl, + .pcs_num = ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_pcs_tbl), + .pcs_misc = sm8550_qmp_gen3x2_pcie_pcs_misc_tbl, + .pcs_misc_num = ARRAY_SIZE(sm8550_qmp_gen3x2_pcie_pcs_misc_tbl), + }, + .reset_list = sdm845_pciephy_reset_l, + .num_resets = ARRAY_SIZE(sdm845_pciephy_reset_l), + .vreg_list = qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), + .regs = pciephy_v5_regs_layout, + + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .phy_status = PHYSTATUS, +}; + +static const struct qmp_pcie_cfg sm8550_qmp_gen4x2_pciephy_cfg = { + .lanes = 2, + + .offsets = &qmp_pcie_offsets_v6_20, + + .tbls = { + .serdes = sm8550_qmp_gen4x2_pcie_serdes_tbl, + .serdes_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_serdes_tbl), + .tx = sm8550_qmp_gen4x2_pcie_tx_tbl, + .tx_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_tx_tbl), + .rx = sm8550_qmp_gen4x2_pcie_rx_tbl, + .rx_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_rx_tbl), + .pcs = sm8550_qmp_gen4x2_pcie_pcs_tbl, + .pcs_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_tbl), + .pcs_misc = sm8550_qmp_gen4x2_pcie_pcs_misc_tbl, + .pcs_misc_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_misc_tbl), + .ln_shrd = sm8550_qmp_gen4x2_pcie_ln_shrd_tbl, + .ln_shrd_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_ln_shrd_tbl), + }, + .reset_list = sdm845_pciephy_reset_l, + .num_resets = ARRAY_SIZE(sdm845_pciephy_reset_l), + .vreg_list = sm8550_qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(sm8550_qmp_phy_vreg_l), + .regs = pciephy_v6_regs_layout, + + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .phy_status = PHYSTATUS_4_20, + .has_nocsr_reset = true, +}; + +static const struct qmp_pcie_cfg sm8650_qmp_gen4x2_pciephy_cfg = { + .lanes = 2, + + .offsets = &qmp_pcie_offsets_v6_20, + + .tbls = { + .serdes = sm8550_qmp_gen4x2_pcie_serdes_tbl, + .serdes_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_serdes_tbl), + .tx = sm8550_qmp_gen4x2_pcie_tx_tbl, + .tx_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_tx_tbl), + .rx = sm8650_qmp_gen4x2_pcie_rx_tbl, + .rx_num = ARRAY_SIZE(sm8650_qmp_gen4x2_pcie_rx_tbl), + .pcs = sm8550_qmp_gen4x2_pcie_pcs_tbl, + .pcs_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_tbl), + .pcs_misc = sm8550_qmp_gen4x2_pcie_pcs_misc_tbl, + .pcs_misc_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_pcs_misc_tbl), + .ln_shrd = sm8550_qmp_gen4x2_pcie_ln_shrd_tbl, + .ln_shrd_num = ARRAY_SIZE(sm8550_qmp_gen4x2_pcie_ln_shrd_tbl), + }, + .reset_list = sdm845_pciephy_reset_l, + .num_resets = ARRAY_SIZE(sdm845_pciephy_reset_l), + .vreg_list = sm8550_qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(sm8550_qmp_phy_vreg_l), + .regs = pciephy_v6_regs_layout, + + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .phy_status = PHYSTATUS_4_20, + .has_nocsr_reset = true, +}; + +static const struct qmp_pcie_cfg x1e80100_qmp_gen4x2_pciephy_cfg = { + .lanes = 2, + + .offsets = &qmp_pcie_offsets_v6_20, + + .tbls = { + .serdes = x1e80100_qmp_gen4x2_pcie_serdes_tbl, + .serdes_num = ARRAY_SIZE(x1e80100_qmp_gen4x2_pcie_serdes_tbl), + .tx = x1e80100_qmp_gen4x2_pcie_tx_tbl, + .tx_num = ARRAY_SIZE(x1e80100_qmp_gen4x2_pcie_tx_tbl), + .rx = x1e80100_qmp_gen4x2_pcie_rx_tbl, + .rx_num = ARRAY_SIZE(x1e80100_qmp_gen4x2_pcie_rx_tbl), + .pcs = x1e80100_qmp_gen4x2_pcie_pcs_tbl, + .pcs_num = ARRAY_SIZE(x1e80100_qmp_gen4x2_pcie_pcs_tbl), + .pcs_misc = x1e80100_qmp_gen4x2_pcie_pcs_misc_tbl, + .pcs_misc_num = ARRAY_SIZE(x1e80100_qmp_gen4x2_pcie_pcs_misc_tbl), + .ln_shrd = x1e80100_qmp_gen4x2_pcie_ln_shrd_tbl, + .ln_shrd_num = ARRAY_SIZE(x1e80100_qmp_gen4x2_pcie_ln_shrd_tbl), + }, + .reset_list = sdm845_pciephy_reset_l, + .num_resets = ARRAY_SIZE(sdm845_pciephy_reset_l), + .vreg_list = qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), + .regs = pciephy_v6_regs_layout, + + .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL, + .phy_status = PHYSTATUS_4_20, + .has_nocsr_reset = true, +}; + +static void qmp_pcie_configure_lane(void __iomem *base, + const struct qmp_pcie_init_tbl tbl[], + int num, u8 lane_mask) +{ + int i; + const struct qmp_pcie_init_tbl *t = tbl; + + if (!t) + return; + + for (i = 0; i < num; i++, t++) { + if (!(t->lane_mask & lane_mask)) + continue; + + writel(t->val, base + t->offset); + } +} + +static void qmp_pcie_configure(void __iomem *base, + const struct qmp_pcie_init_tbl tbl[], + int num) +{ + qmp_pcie_configure_lane(base, tbl, num, 0xff); +} + +static void qmp_pcie_init_registers(struct qmp_pcie_priv *qmp, const struct qmp_pcie_cfg *cfg) +{ + const struct qmp_pcie_cfg_tbls *tbls = &cfg->tbls; + void __iomem *serdes = qmp->serdes; + void __iomem *tx = qmp->tx; + void __iomem *rx = qmp->rx; + void __iomem *tx2 = qmp->tx2; + void __iomem *rx2 = qmp->rx2; + void __iomem *pcs = qmp->pcs; + void __iomem *pcs_misc = qmp->pcs_misc; + void __iomem *ln_shrd = qmp->ln_shrd; + + qmp_pcie_configure(serdes, tbls->serdes, tbls->serdes_num); + + qmp_pcie_configure_lane(tx, tbls->tx, tbls->tx_num, 1); + qmp_pcie_configure_lane(rx, tbls->rx, tbls->rx_num, 1); + + if (cfg->lanes >= 2) { + qmp_pcie_configure_lane(tx2, tbls->tx, tbls->tx_num, 2); + qmp_pcie_configure_lane(rx2, tbls->rx, tbls->rx_num, 2); + } + + qmp_pcie_configure(pcs, tbls->pcs, tbls->pcs_num); + qmp_pcie_configure(pcs_misc, tbls->pcs_misc, tbls->pcs_misc_num); + + qmp_pcie_configure(ln_shrd, tbls->ln_shrd, tbls->ln_shrd_num); +} + +static int qmp_pcie_do_reset(struct qmp_pcie_priv *qmp) +{ + const struct qmp_pcie_cfg *cfg = qmp->cfg; + int i, ret; + + for (i = 0; i < qmp->reset_count; i++) { + ret = reset_assert(&qmp->resets[i]); + if (ret) + return ret; + } + + if (cfg->has_nocsr_reset) + reset_assert(&qmp->nocsr_reset); + + udelay(10); + + for (i = 0; i < qmp->reset_count; i++) { + ret = reset_deassert(&qmp->resets[i]); + if (ret) + return ret; + } + + udelay(50); + + return 0; +} + +static int qmp_pcie_power_on(struct phy *phy) +{ + struct qmp_pcie_priv *qmp = dev_get_priv(phy->dev); + const struct qmp_pcie_cfg *cfg = qmp->cfg; + void __iomem *pcs = qmp->pcs; + void __iomem *status; + unsigned int mask, val; + int ret, i; + + for (i = 0; i < qmp->vreg_count; i++) { + ret = regulator_set_enable(qmp->vregs[i], true); + if (ret && ret != -ENOSYS) + dev_err(phy->dev, "failed to enable regulator %d (%d)\n", i, ret); + } + + ret = qmp_pcie_do_reset(qmp); + if (ret) + return ret; + + for (i = 0; i < qmp->clk_count; i++) { + ret = clk_enable(&qmp->clks[i]); + if (ret && ret != -ENOSYS) { + dev_err(phy->dev, "failed to enable clock %d\n", i); + return ret; + } + } + + /* Power down PHY */ + qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], cfg->pwrdn_ctrl); + + qmp_pcie_init_registers(qmp, cfg); + + clk_enable(&qmp->pipe_clk); + + if (cfg->has_nocsr_reset) + reset_deassert(&qmp->nocsr_reset); + + /* Pull PHY out of reset state */ + qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); + + /* start SerDes */ + qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], SERDES_START | PCS_START); + + status = pcs + cfg->regs[QPHY_PCS_STATUS]; + mask = cfg->phy_status; + ret = readl_poll_timeout(status, val, !(val & mask), PHY_INIT_COMPLETE_TIMEOUT); + if (ret) { + dev_err(phy->dev, "phy initialization timed-out\n"); + return ret; + } + + return 0; +} + +static int qmp_pcie_power_off(struct phy *phy) +{ + struct qmp_pcie_priv *qmp = dev_get_priv(phy->dev); + const struct qmp_pcie_cfg *cfg = qmp->cfg; + + clk_disable(&qmp->pipe_clk); + + /* PHY reset */ + qphy_setbits(qmp->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); + + /* stop SerDes and Phy-Coding-Sublayer */ + qphy_clrbits(qmp->pcs, cfg->regs[QPHY_START_CTRL], + SERDES_START | PCS_START); + + /* Put PHY into POWER DOWN state: active low */ + qphy_clrbits(qmp->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], + cfg->pwrdn_ctrl); + + return 0; +} + +static int qmp_pcie_vreg_init(struct udevice *dev, struct qmp_pcie_priv *qmp) +{ + const struct qmp_pcie_cfg *cfg = qmp->cfg; + unsigned int vreg; + int ret; + + qmp->vreg_count = cfg->num_vregs; + + for (vreg = 0; vreg < NUM_SUPPLIES && vreg < qmp->vreg_count; ++vreg) { + ret = device_get_supply_regulator(dev, cfg->vreg_list[vreg], &qmp->vregs[vreg]); + if (ret) + dev_warn(dev, "failed to get regulator %d (%d)\n", vreg, ret); + + regulator_set_enable(qmp->vregs[vreg], true); + } + + return 0; +} + +static int qmp_pcie_reset_init(struct udevice *dev, struct qmp_pcie_priv *qmp) +{ + const struct qmp_pcie_cfg *cfg = qmp->cfg; + int num = cfg->num_resets; + int i, ret; + + qmp->reset_count = 0; + qmp->resets = devm_kcalloc(dev, num, sizeof(*qmp->resets), GFP_KERNEL); + if (!qmp->resets) + return -ENOMEM; + + for (i = 0; i < num; i++) { + ret = reset_get_by_name(dev, cfg->reset_list[i], &qmp->resets[i]); + if (ret) { + dev_err(dev, "failed to get reset %d\n", i); + goto reset_get_err; + } + + ++qmp->reset_count; + } + + if (cfg->has_nocsr_reset) { + ret = reset_get_by_name(dev, "phy_nocsr", &qmp->nocsr_reset); + if (ret) + dev_warn(dev, "failed to get nocsr reset\n"); + } + + return 0; + +reset_get_err: + reset_release_all(qmp->resets, qmp->reset_count); + + return ret; +} + +static int qmp_pcie_clk_init(struct udevice *dev, struct qmp_pcie_priv *qmp) +{ + int num = ARRAY_SIZE(qmp_pciephy_clk_l); + int i, ret; + + qmp->clk_count = 0; + qmp->clks = devm_kcalloc(dev, num, sizeof(*qmp->clks), GFP_KERNEL); + if (!qmp->clks) + return -ENOMEM; + + for (i = 0; i < num; i++) { + ret = clk_get_by_name(dev, qmp_pciephy_clk_l[i], &qmp->clks[i]); + /* Ignore failure to get ref clock */ + if (ret && strcmp(qmp_pciephy_clk_l[i], "ref") != 0) { + dev_err(dev, "failed to get clock %d\n", i); + goto clk_get_err; + } + + ++qmp->clk_count; + } + + ret = clk_get_by_name(dev, "pipe", &qmp->pipe_clk); + if (ret) + dev_warn(dev, "failed to get pipe clock\n"); + + return 0; + +clk_get_err: + clk_release_all(qmp->clks, qmp->clk_count); + + return ret; +} + +static int qmp_pcie_parse_dt(struct udevice *dev, struct qmp_pcie_priv *qmp) +{ + const struct qmp_pcie_offsets *offs = qmp->cfg->offsets; + const struct qmp_pcie_cfg *cfg = qmp->cfg; + struct resource res; + int ret; + + if (!qmp->cfg->offsets) { + dev_err(dev, "missing PCIE offsets\n"); + return -EINVAL; + } + + ret = ofnode_read_resource(dev_ofnode(dev), 0, &res); + if (ret) { + dev_err(dev, "can't get reg property\n"); + return ret; + } + + qmp->serdes = (void __iomem *)res.start + offs->serdes; + qmp->pcs = (void __iomem *)res.start + offs->pcs; + qmp->pcs_misc = (void __iomem *)res.start + offs->pcs_misc; + qmp->tx = (void __iomem *)res.start + offs->tx; + qmp->rx = (void __iomem *)res.start + offs->rx; + + if (qmp->cfg->lanes >= 2) { + qmp->tx2 = (void __iomem *)res.start + offs->tx2; + qmp->rx2 = (void __iomem *)res.start + offs->rx2; + } + + if (cfg->tbls.ln_shrd) + qmp->ln_shrd = (void __iomem *)res.start + offs->ln_shrd; + + return 0; +} + +static int qmp_pcie_probe(struct udevice *dev) +{ + struct qmp_pcie_priv *qmp = dev_get_priv(dev); + int ret; + + qmp->serdes = (void __iomem *)dev_read_addr(dev); + if (IS_ERR(qmp->serdes)) + return PTR_ERR(qmp->serdes); + + qmp->cfg = (const struct qmp_pcie_cfg *)dev_get_driver_data(dev); + if (!qmp->cfg) + return -EINVAL; + + ret = qmp_pcie_clk_init(dev, qmp); + if (ret) { + dev_err(dev, "failed to get PCIE clks\n"); + return ret; + } + + ret = qmp_pcie_vreg_init(dev, qmp); + if (ret) { + dev_err(dev, "failed to get PCIE voltage regulators\n"); + return ret; + } + + ret = qmp_pcie_reset_init(dev, qmp); + if (ret) { + dev_err(dev, "failed to get PCIE resets\n"); + return ret; + } + + qmp->dev = dev; + + return qmp_pcie_parse_dt(dev, qmp); +} + +static struct phy_ops qmp_pcie_ops = { + .power_on = qmp_pcie_power_on, + .power_off = qmp_pcie_power_off, +}; + +static const struct udevice_id qmp_pcie_ids[] = { + { + .compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy", + .data = (ulong)&sm8550_qmp_gen3x2_pciephy_cfg, + }, { + .compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy", + .data = (ulong)&sm8550_qmp_gen4x2_pciephy_cfg + }, { + .compatible = "qcom,sm8650-qmp-gen3x2-pcie-phy", + .data = (ulong)&sm8550_qmp_gen3x2_pciephy_cfg, + }, { + .compatible = "qcom,sm8650-qmp-gen4x2-pcie-phy", + .data = (ulong)&sm8650_qmp_gen4x2_pciephy_cfg + }, { + .compatible = "qcom,x1e80100-qmp-gen3x2-pcie-phy", + .data = (ulong)&sm8550_qmp_gen3x2_pciephy_cfg + }, { + .compatible = "qcom,x1e80100-qmp-gen4x2-pcie-phy", + .data = (ulong)&x1e80100_qmp_gen4x2_pciephy_cfg + }, { + .compatible = "qcom,x1e80100-qmp-gen4x4-pcie-phy", + .data = (ulong)&x1e80100_qmp_gen4x2_pciephy_cfg + }, + { /* sentinel */ } +}; + +U_BOOT_DRIVER(qcom_qmp_pcie) = { + .name = "qcom-qmp-pcie", + .id = UCLASS_PHY, + .of_match = qmp_pcie_ids, + .ops = &qmp_pcie_ops, + .probe = qmp_pcie_probe, + .priv_auto = sizeof(struct qmp_pcie_priv), +}; diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-misc-v3.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-misc-v3.h new file mode 100644 index 0000000000000000000000000000000000000000..a45bd301bc9ea68114d4943ce51ce50bec6c560f --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-misc-v3.h @@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCS_MISC_V3_H_ +#define QCOM_PHY_QMP_PCS_MISC_V3_H_ + +/* Only for QMP V3 PHY - PCS_MISC registers */ +#define QPHY_V3_PCS_MISC_CLAMP_ENABLE 0x0c +#define QPHY_V3_PCS_MISC_OSC_DTCT_CONFIG2 0x2c +#define QPHY_V3_PCS_MISC_PCIE_INT_AUX_CLK_CONFIG1 0x44 +#define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG2 0x54 +#define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG4 0x5c +#define QPHY_V3_PCS_MISC_OSC_DTCT_MODE2_CONFIG5 0x60 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4.h new file mode 100644 index 0000000000000000000000000000000000000000..4cc02288d418aac6a6464887886a5e913dc9fdb1 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4.h @@ -0,0 +1,72 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCS_PCIE_V4_H_ +#define QCOM_PHY_QMP_PCS_PCIE_V4_H_ + +/* Only for QMP V4 PHY - PCS_PCIE registers (same as PCS_MISC?) */ +#define QPHY_V4_PCS_PCIE_INT_AUX_CLK_STATUS 0x00 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_STATUS 0x04 +#define QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG1 0x08 +#define QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG2 0x0c +#define QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG3 0x10 +#define QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG4 0x14 +#define QPHY_V4_PCS_PCIE_PCS_TX_RX_CONFIG 0x18 +#define QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_DRIVE 0x1c +#define QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_CNTRL 0x20 +#define QPHY_V4_PCS_PCIE_EPCLK_PRE_PLL_LOCK_DLY_AUXCLK 0x24 +#define QPHY_V4_PCS_PCIE_EPCLK_DLY_COUNT_VAL_L 0x28 +#define QPHY_V4_PCS_PCIE_EPCLK_DLY_COUNT_VAL_H 0x2c +#define QPHY_V4_PCS_PCIE_RX_IDLE_DTCT_CNTRL1 0x30 +#define QPHY_V4_PCS_PCIE_RX_IDLE_DTCT_CNTRL2 0x34 +#define QPHY_V4_PCS_PCIE_SIGDET_CNTRL 0x38 +#define QPHY_V4_PCS_PCIE_SIGDET_LOW_2_IDLE_TIME 0x3c +#define QPHY_V4_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L 0x40 +#define QPHY_V4_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_H 0x44 +#define QPHY_V4_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L 0x48 +#define QPHY_V4_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_H 0x4c +#define QPHY_V4_PCS_PCIE_INT_AUX_CLK_CONFIG1 0x50 +#define QPHY_V4_PCS_PCIE_INT_AUX_CLK_CONFIG2 0x54 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG1 0x58 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG2 0x5c +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG3 0x60 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG4 0x64 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG5 0x68 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG6 0x6c +#define QPHY_V4_PCS_PCIE_OSC_DTCT_CONFIG7 0x70 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG1 0x74 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG2 0x78 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG3 0x7c +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG4 0x80 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5 0x84 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG6 0x88 +#define QPHY_V4_PCS_PCIE_OSC_DTCT_MODE2_CONFIG7 0x8c +#define QPHY_V4_PCS_PCIE_OSC_DTCT_ACTIONS 0x90 +#define QPHY_V4_PCS_PCIE_LOCAL_FS 0x94 +#define QPHY_V4_PCS_PCIE_LOCAL_LF 0x98 +#define QPHY_V4_PCS_PCIE_LOCAL_FS_RS 0x9c +#define QPHY_V4_PCS_PCIE_EQ_CONFIG1 0xa0 +#define QPHY_V4_PCS_PCIE_EQ_CONFIG2 0xa4 +#define QPHY_V4_PCS_PCIE_PRESET_P0_P1_PRE 0xa8 +#define QPHY_V4_PCS_PCIE_PRESET_P2_P3_PRE 0xac +#define QPHY_V4_PCS_PCIE_PRESET_P4_P5_PRE 0xb0 +#define QPHY_V4_PCS_PCIE_PRESET_P6_P7_PRE 0xb4 +#define QPHY_V4_PCS_PCIE_PRESET_P8_P9_PRE 0xb8 +#define QPHY_V4_PCS_PCIE_PRESET_P10_PRE 0xbc +#define QPHY_V4_PCS_PCIE_PRESET_P1_P3_PRE_RS 0xc0 +#define QPHY_V4_PCS_PCIE_PRESET_P4_P5_PRE_RS 0xc4 +#define QPHY_V4_PCS_PCIE_PRESET_P6_P9_PRE_RS 0xc8 +#define QPHY_V4_PCS_PCIE_PRESET_P0_P1_POST 0xcc +#define QPHY_V4_PCS_PCIE_PRESET_P2_P3_POST 0xd0 +#define QPHY_V4_PCS_PCIE_PRESET_P4_P5_POST 0xd4 +#define QPHY_V4_PCS_PCIE_PRESET_P6_P7_POST 0xd8 +#define QPHY_V4_PCS_PCIE_PRESET_P8_P9_POST 0xdc +#define QPHY_V4_PCS_PCIE_PRESET_P10_POST 0xe0 +#define QPHY_V4_PCS_PCIE_PRESET_P1_P3_POST_RS 0xe4 +#define QPHY_V4_PCS_PCIE_PRESET_P4_P5_POST_RS 0xe8 +#define QPHY_V4_PCS_PCIE_PRESET_P6_P9_POST_RS 0xec +#define QPHY_V4_PCS_PCIE_RXEQEVAL_TIME 0xf0 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4_20.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4_20.h new file mode 100644 index 0000000000000000000000000000000000000000..ac872a9eff9a8fe7fc3307759288aee15d17bd24 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v4_20.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCS_PCIE_V4_20_H_ +#define QCOM_PHY_QMP_PCS_PCIE_V4_20_H_ + +#define QPHY_V4_20_PCS_PCIE_ENDPOINT_REFCLK_DRIVE 0x01c +#define QPHY_V4_20_PCS_PCIE_OSC_DTCT_ACTIONS 0x090 +#define QPHY_V4_20_PCS_PCIE_EQ_CONFIG1 0x0a0 +#define QPHY_V4_20_PCS_PCIE_G3_RXEQEVAL_TIME 0x0f0 +#define QPHY_V4_20_PCS_PCIE_G4_RXEQEVAL_TIME 0x0f4 +#define QPHY_V4_20_PCS_PCIE_G4_EQ_CONFIG2 0x0fc +#define QPHY_V4_20_PCS_PCIE_G4_EQ_CONFIG5 0x108 +#define QPHY_V4_20_PCS_LANE1_INSIG_SW_CTRL2 0x824 +#define QPHY_V4_20_PCS_LANE1_INSIG_MX_CTRL2 0x828 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5.h new file mode 100644 index 0000000000000000000000000000000000000000..2801bcf10f28e323b62a577b3bee82c2ca22c245 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5.h @@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCS_PCIE_V5_H_ +#define QCOM_PHY_QMP_PCS_PCIE_V5_H_ + +/* Only for QMP V5 PHY - PCS_PCIE registers */ +#define QPHY_V5_PCS_PCIE_POWER_STATE_CONFIG2 0x0c +#define QPHY_V5_PCS_PCIE_POWER_STATE_CONFIG4 0x14 +#define QPHY_V5_PCS_PCIE_ENDPOINT_REFCLK_DRIVE 0x20 +#define QPHY_V5_PCS_PCIE_INT_AUX_CLK_CONFIG1 0x54 +#define QPHY_V5_PCS_PCIE_OSC_DTCT_ACTIONS 0x94 +#define QPHY_V5_PCS_PCIE_EQ_CONFIG2 0xa8 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5_20.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5_20.h new file mode 100644 index 0000000000000000000000000000000000000000..cdf8c04ea078a985be82d561ad0918dfdece9987 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v5_20.h @@ -0,0 +1,23 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCS_PCIE_V5_20_H_ +#define QCOM_PHY_QMP_PCS_PCIE_V5_20_H_ + +/* Only for QMP V5_20 PHY - PCIe PCS registers */ +#define QPHY_V5_20_PCS_PCIE_POWER_STATE_CONFIG2 0x00c +#define QPHY_V5_20_PCS_PCIE_ENDPOINT_REFCLK_DRIVE 0x01c +#define QPHY_V5_20_PCS_PCIE_OSC_DTCT_MODE2_CONFIG5 0x084 +#define QPHY_V5_20_PCS_PCIE_OSC_DTCT_ACTIONS 0x090 +#define QPHY_V5_20_PCS_PCIE_EQ_CONFIG1 0x0a0 +#define QPHY_V5_20_PCS_PCIE_PRESET_P10_POST 0x0e0 +#define QPHY_V5_20_PCS_PCIE_G4_EQ_CONFIG2 0x0fc +#define QPHY_V5_20_PCS_PCIE_G4_EQ_CONFIG5 0x108 +#define QPHY_V5_20_PCS_PCIE_G4_PRE_GAIN 0x15c +#define QPHY_V5_20_PCS_PCIE_RX_MARGINING_CONFIG3 0x184 +#define QPHY_V5_20_PCS_LANE1_INSIG_SW_CTRL2 0xa24 +#define QPHY_V5_20_PCS_LANE1_INSIG_MX_CTRL2 0xa28 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6.h new file mode 100644 index 0000000000000000000000000000000000000000..0ca79333d94261610f7274968c96362dcfb1f354 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6.h @@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_H_ +#define QCOM_PHY_QMP_PCS_PCIE_V6_H_ + +/* Only for QMP V6 PHY - PCIE have different offsets than V5 */ +#define QPHY_PCIE_V6_PCS_PCIE_EQ_CONFIG1 0xa4 +#define QPHY_PCIE_V6_PCS_PCIE_RXEQEVAL_TIME 0xf4 +#define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG2 0x0c +#define QPHY_PCIE_V6_PCS_PCIE_POWER_STATE_CONFIG4 0x14 +#define QPHY_PCIE_V6_PCS_PCIE_ENDPOINT_REFCLK_DRIVE 0x20 +#define QPHY_PCIE_V6_PCS_PCIE_OSC_DTCT_ACTIONS 0x94 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6_20.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6_20.h new file mode 100644 index 0000000000000000000000000000000000000000..dfcecf31a6060981b912646fcdf5db83906f5835 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-pcie-v6_20.h @@ -0,0 +1,25 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_PCS_PCIE_V6_20_H_ +#define QCOM_PHY_QMP_PCS_PCIE_V6_20_H_ + +/* Only for QMP V6_20 PHY - PCIE have different offsets than V5 */ +#define QPHY_PCIE_V6_20_PCS_POWER_STATE_CONFIG2 0x00c +#define QPHY_PCIE_V6_20_PCS_TX_RX_CONFIG 0x018 +#define QPHY_PCIE_V6_20_PCS_ENDPOINT_REFCLK_DRIVE 0x01c +#define QPHY_PCIE_V6_20_PCS_OSC_DTCT_ATCIONS 0x090 +#define QPHY_PCIE_V6_20_PCS_EQ_CONFIG1 0x0a0 +#define QPHY_PCIE_V6_20_PCS_G3_RXEQEVAL_TIME 0x0f0 +#define QPHY_PCIE_V6_20_PCS_G4_RXEQEVAL_TIME 0x0f4 +#define QPHY_PCIE_V6_20_PCS_EQ_CONFIG5 0x108 +#define QPHY_PCIE_V6_20_PCS_G4_PRE_GAIN 0x15c +#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG1 0x17c +#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG3 0x184 +#define QPHY_PCIE_V6_20_PCS_RX_MARGINING_CONFIG5 0x18c +#define QPHY_PCIE_V6_20_PCS_G3_FOM_EQ_CONFIG5 0x1ac +#define QPHY_PCIE_V6_20_PCS_G4_FOM_EQ_CONFIG5 0x1c0 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-v5.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-v5.h new file mode 100644 index 0000000000000000000000000000000000000000..36cc80bb9059f6b9262721beb007d3b4edb8219c --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-v5.h @@ -0,0 +1,34 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2017, The Linux Foundation. All rights reserved. + */ + +#ifndef QCOM_PHY_QMP_PCS_V5_H_ +#define QCOM_PHY_QMP_PCS_V5_H_ + +/* Only for QMP V5 PHY - USB/PCIe PCS registers */ +#define QPHY_V5_PCS_SW_RESET 0x000 +#define QPHY_V5_PCS_PCS_STATUS1 0x014 +#define QPHY_V5_PCS_POWER_DOWN_CONTROL 0x040 +#define QPHY_V5_PCS_START_CONTROL 0x044 +#define QPHY_V5_PCS_LOCK_DETECT_CONFIG1 0x0c4 +#define QPHY_V5_PCS_LOCK_DETECT_CONFIG2 0x0c8 +#define QPHY_V5_PCS_LOCK_DETECT_CONFIG3 0x0cc +#define QPHY_V5_PCS_LOCK_DETECT_CONFIG6 0x0d8 +#define QPHY_V5_PCS_REFGEN_REQ_CONFIG1 0x0dc +#define QPHY_V5_PCS_G3S2_PRE_GAIN 0x170 +#define QPHY_V5_PCS_RX_SIGDET_LVL 0x188 +#define QPHY_V5_PCS_RCVR_DTCT_DLY_P1U2_L 0x190 +#define QPHY_V5_PCS_RCVR_DTCT_DLY_P1U2_H 0x194 +#define QPHY_V5_PCS_RATE_SLEW_CNTRL1 0x198 +#define QPHY_V5_PCS_CDR_RESET_TIME 0x1b0 +#define QPHY_V5_PCS_RX_CONFIG 0x1b0 +#define QPHY_V5_PCS_ALIGN_DETECT_CONFIG1 0x1c0 +#define QPHY_V5_PCS_ALIGN_DETECT_CONFIG2 0x1c4 +#define QPHY_V5_PCS_PCS_TX_RX_CONFIG 0x1d0 +#define QPHY_V5_PCS_EQ_CONFIG1 0x1dc +#define QPHY_V5_PCS_EQ_CONFIG2 0x1e0 +#define QPHY_V5_PCS_EQ_CONFIG3 0x1e4 +#define QPHY_V5_PCS_EQ_CONFIG5 0x1ec + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-v6.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-v6.h new file mode 100644 index 0000000000000000000000000000000000000000..08299d2b78f096fa5f9388a4d54ddfa85667b18c --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-v6.h @@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_PCS_V6_H_ +#define QCOM_PHY_QMP_PCS_V6_H_ + +/* Only for QMP V6 PHY - USB/PCIe PCS registers */ +#define QPHY_V6_PCS_SW_RESET 0x000 +#define QPHY_V6_PCS_PCS_STATUS1 0x014 +#define QPHY_V6_PCS_POWER_DOWN_CONTROL 0x040 +#define QPHY_V6_PCS_START_CONTROL 0x044 +#define QPHY_V6_PCS_POWER_STATE_CONFIG1 0x090 +#define QPHY_V6_PCS_LOCK_DETECT_CONFIG1 0x0c4 +#define QPHY_V6_PCS_LOCK_DETECT_CONFIG2 0x0c8 +#define QPHY_V6_PCS_LOCK_DETECT_CONFIG3 0x0cc +#define QPHY_V6_PCS_LOCK_DETECT_CONFIG6 0x0d8 +#define QPHY_V6_PCS_REFGEN_REQ_CONFIG1 0x0dc +#define QPHY_V6_PCS_RX_SIGDET_LVL 0x188 +#define QPHY_V6_PCS_RCVR_DTCT_DLY_P1U2_L 0x190 +#define QPHY_V6_PCS_RCVR_DTCT_DLY_P1U2_H 0x194 +#define QPHY_V6_PCS_RATE_SLEW_CNTRL1 0x198 +#define QPHY_V6_PCS_CDR_RESET_TIME 0x1b0 +#define QPHY_V6_PCS_ALIGN_DETECT_CONFIG1 0x1c0 +#define QPHY_V6_PCS_ALIGN_DETECT_CONFIG2 0x1c4 +#define QPHY_V6_PCS_PCS_TX_RX_CONFIG 0x1d0 +#define QPHY_V6_PCS_EQ_CONFIG1 0x1dc +#define QPHY_V6_PCS_EQ_CONFIG2 0x1e0 +#define QPHY_V6_PCS_EQ_CONFIG5 0x1ec + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-pcs-v6_20.h b/drivers/phy/qcom/phy-qcom-qmp-pcs-v6_20.h new file mode 100644 index 0000000000000000000000000000000000000000..4d9615cc0383cee27f312cbb39771d7ae79f71bb --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-pcs-v6_20.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_PCS_V6_20_H_ +#define QCOM_PHY_QMP_PCS_V6_20_H_ + +/* Only for QMP V6_20 PHY - USB/PCIe PCS registers */ +#define QPHY_V6_20_PCS_G12S1_TXDEEMPH_M6DB 0x170 +#define QPHY_V6_20_PCS_G3S2_PRE_GAIN 0x178 +#define QPHY_V6_20_PCS_RX_SIGDET_LVL 0x190 +#define QPHY_V6_20_PCS_COM_ELECIDLE_DLY_SEL 0x1b8 +#define QPHY_V6_20_PCS_TX_RX_CONFIG1 0x1dc +#define QPHY_V6_20_PCS_TX_RX_CONFIG2 0x1e0 +#define QPHY_V6_20_PCS_EQ_CONFIG4 0x1f8 +#define QPHY_V6_20_PCS_EQ_CONFIG5 0x1fc + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-qserdes-ln-shrd-v6.h b/drivers/phy/qcom/phy-qcom-qmp-qserdes-ln-shrd-v6.h new file mode 100644 index 0000000000000000000000000000000000000000..86d7d796d5d7b3693321e3fc12a31bfe30008dca --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-qserdes-ln-shrd-v6.h @@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_QSERDES_LN_SHRD_V6_H_ +#define QCOM_PHY_QMP_QSERDES_LN_SHRD_V6_H_ + +#define QSERDES_V6_LN_SHRD_RXCLK_DIV2_CTRL 0xa0 +#define QSERDES_V6_LN_SHRD_RX_Q_EN_RATES 0xb0 +#define QSERDES_V6_LN_SHRD_DFE_DAC_ENABLE1 0xb4 +#define QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH1 0xc4 +#define QSERDES_V6_LN_SHRD_TX_ADAPT_POST_THRESH2 0xc8 +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B0 0xd4 +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B1 0xd8 +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B2 0xdc +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B3 0xe0 +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B4 0xe4 +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B5 0xe8 +#define QSERDES_V6_LN_SHRD_RX_MODE_RATE_0_1_B6 0xec +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE210 0xf0 +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH1_RATE3 0xf4 +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE210 0xf8 +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH2_RATE3 0xfc +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE210 0x100 +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH3_RATE3 0x104 +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH4_RATE3 0x10c +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH5_RATE3 0x114 +#define QSERDES_V6_LN_SHRD_RX_MARG_COARSE_THRESH6_RATE3 0x11c +#define QSERDES_V6_LN_SHRD_RX_SUMMER_CAL_SPD_MODE 0x128 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6.h b/drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6.h new file mode 100644 index 0000000000000000000000000000000000000000..23ffcfae9efab4a9e081414f9b3bbd0079d34f18 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6.h @@ -0,0 +1,83 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_QSERDES_TXRX_USB_V6_H_ +#define QCOM_PHY_QMP_QSERDES_TXRX_USB_V6_H_ + +#define QSERDES_V6_TX_CLKBUF_ENABLE 0x08 +#define QSERDES_V6_TX_TX_EMP_POST1_LVL 0x0c +#define QSERDES_V6_TX_TX_DRV_LVL 0x14 +#define QSERDES_V6_TX_RESET_TSYNC_EN 0x1c +#define QSERDES_V6_TX_PRE_STALL_LDO_BOOST_EN 0x20 +#define QSERDES_V6_TX_TX_BAND 0x24 +#define QSERDES_V6_TX_INTERFACE_SELECT 0x2c +#define QSERDES_V6_TX_RES_CODE_LANE_TX 0x34 +#define QSERDES_V6_TX_RES_CODE_LANE_RX 0x38 +#define QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX 0x3c +#define QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX 0x40 +#define QSERDES_V6_TX_TRANSCEIVER_BIAS_EN 0x54 +#define QSERDES_V6_TX_HIGHZ_DRVR_EN 0x58 +#define QSERDES_V6_TX_TX_POL_INV 0x5c +#define QSERDES_V6_TX_PARRATE_REC_DETECT_IDLE_EN 0x60 +#define QSERDES_V6_TX_BIST_PATTERN7 0x7c +#define QSERDES_V6_TX_LANE_MODE_1 0x84 +#define QSERDES_V6_TX_LANE_MODE_2 0x88 +#define QSERDES_V6_TX_LANE_MODE_3 0x8c +#define QSERDES_V6_TX_LANE_MODE_4 0x90 +#define QSERDES_V6_TX_LANE_MODE_5 0x94 +#define QSERDES_V6_TX_RCV_DETECT_LVL_2 0xa4 +#define QSERDES_V6_TX_TRAN_DRVR_EMP_EN 0xc0 +#define QSERDES_V6_TX_TX_INTERFACE_MODE 0xc4 +#define QSERDES_V6_TX_VMODE_CTRL1 0xc8 +#define QSERDES_V6_TX_PI_QEC_CTRL 0xe4 + +#define QSERDES_V6_RX_UCDR_FO_GAIN 0x08 +#define QSERDES_V6_RX_UCDR_SO_GAIN 0x14 +#define QSERDES_V6_RX_UCDR_FASTLOCK_FO_GAIN 0x30 +#define QSERDES_V6_RX_UCDR_SO_SATURATION_AND_ENABLE 0x34 +#define QSERDES_V6_RX_UCDR_FASTLOCK_COUNT_LOW 0x3c +#define QSERDES_V6_RX_UCDR_FASTLOCK_COUNT_HIGH 0x40 +#define QSERDES_V6_RX_UCDR_PI_CONTROLS 0x44 +#define QSERDES_V6_RX_UCDR_SB2_THRESH1 0x4c +#define QSERDES_V6_RX_UCDR_SB2_THRESH2 0x50 +#define QSERDES_V6_RX_UCDR_SB2_GAIN1 0x54 +#define QSERDES_V6_RX_UCDR_SB2_GAIN2 0x58 +#define QSERDES_V6_RX_AUX_DATA_TCOARSE_TFINE 0x60 +#define QSERDES_V6_RX_TX_ADAPT_POST_THRESH 0xcc +#define QSERDES_V6_RX_VGA_CAL_CNTRL1 0xd4 +#define QSERDES_V6_RX_VGA_CAL_CNTRL2 0xd8 +#define QSERDES_V6_RX_GM_CAL 0xdc +#define QSERDES_V6_RX_RX_EQU_ADAPTOR_CNTRL2 0xec +#define QSERDES_V6_RX_RX_EQU_ADAPTOR_CNTRL3 0xf0 +#define QSERDES_V6_RX_RX_EQU_ADAPTOR_CNTRL4 0xf4 +#define QSERDES_V6_RX_RX_IDAC_TSETTLE_LOW 0xf8 +#define QSERDES_V6_RX_RX_IDAC_TSETTLE_HIGH 0xfc +#define QSERDES_V6_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x110 +#define QSERDES_V6_RX_SIDGET_ENABLES 0x118 +#define QSERDES_V6_RX_SIGDET_CNTRL 0x11c +#define QSERDES_V6_RX_SIGDET_DEGLITCH_CNTRL 0x124 +#define QSERDES_V6_RX_RX_MODE_00_LOW 0x15c +#define QSERDES_V6_RX_RX_MODE_00_HIGH 0x160 +#define QSERDES_V6_RX_RX_MODE_00_HIGH2 0x164 +#define QSERDES_V6_RX_RX_MODE_00_HIGH3 0x168 +#define QSERDES_V6_RX_RX_MODE_00_HIGH4 0x16c +#define QSERDES_V6_RX_RX_MODE_01_LOW 0x170 +#define QSERDES_V6_RX_RX_MODE_01_HIGH 0x174 +#define QSERDES_V6_RX_RX_MODE_01_HIGH2 0x178 +#define QSERDES_V6_RX_RX_MODE_01_HIGH3 0x17c +#define QSERDES_V6_RX_RX_MODE_01_HIGH4 0x180 +#define QSERDES_V6_RX_RX_MODE_10_LOW 0x184 +#define QSERDES_V6_RX_RX_MODE_10_HIGH 0x188 +#define QSERDES_V6_RX_RX_MODE_10_HIGH2 0x18c +#define QSERDES_V6_RX_RX_MODE_10_HIGH3 0x190 +#define QSERDES_V6_RX_RX_MODE_10_HIGH4 0x194 +#define QSERDES_V6_RX_DFE_EN_TIMER 0x1a0 +#define QSERDES_V6_RX_DFE_CTLE_POST_CAL_OFFSET 0x1a4 +#define QSERDES_V6_RX_DCC_CTRL1 0x1a8 +#define QSERDES_V6_RX_VTH_CODE 0x1b0 +#define QSERDES_V6_RX_SIGDET_CAL_CTRL1 0x1e4 +#define QSERDES_V6_RX_SIGDET_CAL_TRIM 0x1f8 + +#endif diff --git a/drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6_20.h b/drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6_20.h new file mode 100644 index 0000000000000000000000000000000000000000..7bac5d5c6c34485bdb357bf3a3caa7658ba07aa0 --- /dev/null +++ b/drivers/phy/qcom/phy-qcom-qmp-qserdes-txrx-v6_20.h @@ -0,0 +1,51 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2023, Linaro Limited + */ + +#ifndef QCOM_PHY_QMP_QSERDES_TXRX_PCIE_V6_20_H_ +#define QCOM_PHY_QMP_QSERDES_TXRX_PCIE_V6_20_H_ + +#define QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_TX 0x30 +#define QSERDES_V6_20_TX_RES_CODE_LANE_OFFSET_RX 0x34 +#define QSERDES_V6_20_TX_TRAN_DRVR_EMP_EN 0xac +#define QSERDES_V6_20_TX_LANE_MODE_1 0x78 +#define QSERDES_V6_20_TX_LANE_MODE_2 0x7c +#define QSERDES_V6_20_TX_LANE_MODE_3 0x80 + +#define QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_2 0x08 +#define QSERDES_V6_20_RX_UCDR_FO_GAIN_RATE_3 0x0c +#define QSERDES_V6_20_RX_UCDR_SO_GAIN_RATE_2 0x18 +#define QSERDES_V6_20_RX_UCDR_PI_CONTROLS 0x20 +#define QSERDES_V6_20_RX_UCDR_SO_ACC_DEFAULT_VAL_RATE3 0x34 +#define QSERDES_V6_20_RX_IVCM_CAL_CTRL2 0x9c +#define QSERDES_V6_20_RX_IVCM_POSTCAL_OFFSET 0xa0 +#define QSERDES_V6_20_RX_DFE_1 0xac +#define QSERDES_V6_20_RX_DFE_2 0xb0 +#define QSERDES_V6_20_RX_DFE_3 0xb4 +#define QSERDES_V6_20_RX_TX_ADPT_CTRL 0xd4 +#define QSERDES_V6_20_VGA_CAL_CNTRL1 0xe0 +#define QSERDES_V6_20_RX_VGA_CAL_MAN_VAL 0xe8 +#define QSERDES_V6_20_RX_GM_CAL 0x10c +#define QSERDES_V6_20_RX_EQU_ADAPTOR_CNTRL4 0x120 +#define QSERDES_V6_20_RX_SIGDET_ENABLES 0x148 +#define QSERDES_V6_20_RX_PHPRE_CTRL 0x188 +#define QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET 0x194 +#define QSERDES_V6_20_RX_Q_PI_INTRINSIC_BIAS_RATE32 0x1dc +#define QSERDES_V6_20_RX_MODE_RATE2_B0 0x1f4 +#define QSERDES_V6_20_RX_MODE_RATE2_B1 0x1f8 +#define QSERDES_V6_20_RX_MODE_RATE2_B2 0x1fc +#define QSERDES_V6_20_RX_MODE_RATE2_B3 0x200 +#define QSERDES_V6_20_RX_MODE_RATE2_B4 0x204 +#define QSERDES_V6_20_RX_MODE_RATE2_B5 0x208 +#define QSERDES_V6_20_RX_MODE_RATE2_B6 0x20c +#define QSERDES_V6_20_RX_MODE_RATE3_B0 0x210 +#define QSERDES_V6_20_RX_MODE_RATE3_B1 0x214 +#define QSERDES_V6_20_RX_MODE_RATE3_B2 0x218 +#define QSERDES_V6_20_RX_MODE_RATE3_B3 0x21c +#define QSERDES_V6_20_RX_MODE_RATE3_B4 0x220 +#define QSERDES_V6_20_RX_MODE_RATE3_B5 0x224 +#define QSERDES_V6_20_RX_MODE_RATE3_B6 0x228 +#define QSERDES_V6_20_RX_BKUP_CTRL1 0x22c + +#endif --- base-commit: 7fe55182d9263a62e18b450c97bdf0b8031e5667 change-id: 20241125-topic-pcie-phy-542f745f39b5 Best regards, -- Neil Armstrong <neil.armstrong(a)linaro.org>

2 1