June 2023 - U-Boot

[PATCH] lds: align u-boot-nodtb with 8 bytes boundary
by Eugen Hristev 29 Jan '25

29 Jan '25

Newer DTC require that the DTB start address is aligned at 8 bytes. In the u-boot.bin case, the u-boot-nodtb.bin is concatenated with the DTB, but there is no alignment/padding to the next 8byte aligned address. This causes the board to fail booting, because the FDT will claim that the DTB inside u-boot.bin is not a valid DTB, it will fail with -FDT_ERR_ALIGNMENT. To solve this, have the u-boot binary `_end` aligned with 8 bytes. The objcopy in the Makefile will create the u-boot-nodtb.bin and it has to be truncated to 8 bytes to correspond to the u-boot.map file which will have the `_end` aligned to 8 bytes. The lds files which use devicetrees have been changed to align the `_end` tag with 8 bytes. This patch is also a prerequisite to have the possibility to update the dtc inside u-boot to newer versions (1.6.1+) Signed-off-by: Eugen Hristev <eugen.hristev(a)microchip.com> --- Hi, I could not test all affected boards, it's an impossible task. I tried this on at91 boards which I have, and ran the CI on denx. I cannot guarantee that no other boards are affected, so this patch is a bit of an RFC. If the u-boot-nodtb.bin does not have the size equal with the corresponding one in u-boot.map, the binary_size_check will fail at build time with something like this: u-boot.map shows a binary size of 502684 but u-boot-nodtb.bin shows 502688 Thanks, Eugen Makefile | 2 ++ arch/arm/cpu/armv8/u-boot.lds | 4 ++-- arch/arm/cpu/u-boot-spl.lds | 1 + arch/arm/cpu/u-boot.lds | 1 + arch/arm/lib/elf_arm_efi.lds | 5 +++++ arch/arm/mach-at91/arm926ejs/u-boot-spl.lds | 2 +- arch/arm/mach-at91/armv7/u-boot-spl.lds | 2 +- arch/arm/mach-zynq/u-boot-spl.lds | 2 +- arch/mips/cpu/u-boot.lds | 2 +- arch/sandbox/cpu/u-boot.lds | 6 ++++++ arch/sh/cpu/u-boot.lds | 2 ++ board/ti/am335x/u-boot.lds | 1 + tools/binman/test/u_boot_binman_embed.lds | 2 +- 13 files changed, 25 insertions(+), 7 deletions(-) diff --git a/Makefile b/Makefile index 9d84f96481..b4d387bcce 100644 --- a/Makefile +++ b/Makefile @@ -1317,6 +1317,8 @@ endif u-boot-nodtb.bin: u-boot FORCE $(call if_changed,objcopy_uboot) +# Make sure the size is 8 byte-aligned. + @truncate -s %8 $@ $(BOARD_SIZE_CHECK) u-boot.ldr: u-boot diff --git a/arch/arm/cpu/armv8/u-boot.lds b/arch/arm/cpu/armv8/u-boot.lds index 8fe4682dd2..e5fa4ef95c 100644 --- a/arch/arm/cpu/armv8/u-boot.lds +++ b/arch/arm/cpu/armv8/u-boot.lds @@ -145,10 +145,10 @@ SECTIONS *(.__rel_dyn_end) } - _end = .; - . = ALIGN(8); + _end = .; + .bss_start : { KEEP(*(.__bss_start)); } diff --git a/arch/arm/cpu/u-boot-spl.lds b/arch/arm/cpu/u-boot-spl.lds index fb2189d50d..732ed42db1 100644 --- a/arch/arm/cpu/u-boot-spl.lds +++ b/arch/arm/cpu/u-boot-spl.lds @@ -55,6 +55,7 @@ SECTIONS .end : { + . = ALIGN(8); *(.__end) } diff --git a/arch/arm/cpu/u-boot.lds b/arch/arm/cpu/u-boot.lds index f25f72b2e0..274e1a7d30 100644 --- a/arch/arm/cpu/u-boot.lds +++ b/arch/arm/cpu/u-boot.lds @@ -193,6 +193,7 @@ SECTIONS .end : { + . = ALIGN(8); *(.__end) } diff --git a/arch/arm/lib/elf_arm_efi.lds b/arch/arm/lib/elf_arm_efi.lds index 767ebda635..f3867021d3 100644 --- a/arch/arm/lib/elf_arm_efi.lds +++ b/arch/arm/lib/elf_arm_efi.lds @@ -54,6 +54,11 @@ SECTIONS .rel.data : { *(.rel.data) *(.rel.data*) } _data_size = . - _etext; + .end : { + . = ALIGN(8); + *(.__end) + } + /DISCARD/ : { *(.rel.reloc) *(.eh_frame) diff --git a/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds index 1a8bf94dee..d7e5d81ecc 100644 --- a/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds +++ b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds @@ -31,7 +31,7 @@ SECTIONS . = ALIGN(4); __u_boot_list : { KEEP(*(SORT(__u_boot_list*))) } > .sram - . = ALIGN(4); + . = ALIGN(8); __image_copy_end = .; .end : diff --git a/arch/arm/mach-at91/armv7/u-boot-spl.lds b/arch/arm/mach-at91/armv7/u-boot-spl.lds index 6ca725fc4c..2a0a1b4b86 100644 --- a/arch/arm/mach-at91/armv7/u-boot-spl.lds +++ b/arch/arm/mach-at91/armv7/u-boot-spl.lds @@ -38,7 +38,7 @@ SECTIONS . = ALIGN(4); __u_boot_list : { KEEP(*(SORT(__u_boot_list*))) } > .sram - . = ALIGN(4); + . = ALIGN(8); __image_copy_end = .; .end : diff --git a/arch/arm/mach-zynq/u-boot-spl.lds b/arch/arm/mach-zynq/u-boot-spl.lds index 8c18d3f91f..c0320dbe1e 100644 --- a/arch/arm/mach-zynq/u-boot-spl.lds +++ b/arch/arm/mach-zynq/u-boot-spl.lds @@ -41,7 +41,7 @@ SECTIONS KEEP(*(SORT(__u_boot_list*))); } > .sram - . = ALIGN(4); + . = ALIGN(8); _image_binary_end = .; diff --git a/arch/mips/cpu/u-boot.lds b/arch/mips/cpu/u-boot.lds index 9a4ebcd151..182e9bc6e5 100644 --- a/arch/mips/cpu/u-boot.lds +++ b/arch/mips/cpu/u-boot.lds @@ -56,7 +56,7 @@ SECTIONS . += CONFIG_MIPS_RELOCATION_TABLE_SIZE - 4; } - . = ALIGN(4); + . = ALIGN(8); _end = .; .bss __rel_start (OVERLAY) : { diff --git a/arch/sandbox/cpu/u-boot.lds b/arch/sandbox/cpu/u-boot.lds index ba8dee50c7..3fbca6d248 100644 --- a/arch/sandbox/cpu/u-boot.lds +++ b/arch/sandbox/cpu/u-boot.lds @@ -51,6 +51,12 @@ SECTIONS *(.dynsym) __dyn_sym_end = .; } + + .end : + { + . = ALIGN(8); + *(.__end) + } } INSERT BEFORE .data; diff --git a/arch/sh/cpu/u-boot.lds b/arch/sh/cpu/u-boot.lds index d360eea7eb..226f50b19c 100644 --- a/arch/sh/cpu/u-boot.lds +++ b/arch/sh/cpu/u-boot.lds @@ -74,6 +74,8 @@ SECTIONS KEEP(*(SORT(__u_boot_list*))); } >ram + . = ALIGN(8); + PROVIDE (__init_end = .); PROVIDE (reloc_dst_end = .); PROVIDE (_end = .); diff --git a/board/ti/am335x/u-boot.lds b/board/ti/am335x/u-boot.lds index 087dee8bb2..deb9098a90 100644 --- a/board/ti/am335x/u-boot.lds +++ b/board/ti/am335x/u-boot.lds @@ -118,6 +118,7 @@ SECTIONS .end : { + . = ALIGN(8); *(.__end) } diff --git a/tools/binman/test/u_boot_binman_embed.lds b/tools/binman/test/u_boot_binman_embed.lds index e213fa8a84..93c0ae6aed 100644 --- a/tools/binman/test/u_boot_binman_embed.lds +++ b/tools/binman/test/u_boot_binman_embed.lds @@ -18,7 +18,7 @@ SECTIONS *(.text*) } - . = ALIGN(4); + . = ALIGN(8); .data : { dtb_embed_begin = .; KEEP(*(.mydtb)); -- 2.25.1

8 26

[PATCH v2 0/2] sunxi, usb: UDC/DM gadget model support
by Sam Edwards 15 Jul '24

15 Jul '24

Happy Thursday, U-Boot list! Here is attempt 2 at making this USB controller driver compatible with DM's gadget model, following what most of the other musb variants do. v2 removes the unwanted printfs in the probe func, per feedback from Marek. I received no other feedback against v1 of this patch. Cheers, Sam Sam Edwards (2): usb: musb-new: sunxi: remove unwanted printfs usb: musb-new: sunxi: make compatible with UDC/DM gadget model drivers/usb/musb-new/sunxi.c | 52 +++++++++++++++++++++--------------- 1 file changed, 31 insertions(+), 21 deletions(-) -- 2.39.2

3 9

[PATCH v2 0/8] Add DFU, emmc and usb boot for TI am62x
by Sjoerd Simons 29 May '24

29 May '24

This series adds more boot sources for the TI am62x. For that the dts' are synced from the upstream ti-next git tree (to add usb nodes), some dwc3 glue is and finally the default configuration is tuned to add support for DFU and USB (host and gadget) Changes in v2: - Update dts sync to v6.3-rc5 - Switch dwc3 glue to a seperate driver rather then in dwc-generic - Minimize config changes to just DFU configuration - Only enable usb port 0 DFU in SPL - Create a seperate defconfig for R5 Sjoerd Simons (8): omap: timer: add ti,am654-timer compatibility arm: mach-k3: am62: Add timer0 id to the dev list arm: dts: k3-am62: Bump dtsi from linux arm: dts: k3-am625-sk: Enable emmc in SPL usb: dwc3: Add dwc3 glue driver for am62 configs: am62: Add configs for enabling USB in U-Boot arm: dts: k3-am625-sk: Enable usb ports in u-boot configs: am62x_evm_*: Enable USB and DFU support arch/arm/dts/k3-am62-main.dtsi | 259 +++++++++++++++++++++++--- arch/arm/dts/k3-am62-mcu.dtsi | 49 +++++ arch/arm/dts/k3-am62-wakeup.dtsi | 4 +- arch/arm/dts/k3-am625-r5-sk.dts | 2 +- arch/arm/dts/k3-am625-sk-u-boot.dtsi | 27 ++- arch/arm/dts/k3-am625-sk.dts | 95 +++++----- arch/arm/dts/k3-am625.dtsi | 52 ++++++ arch/arm/mach-k3/am62x/dev-data.c | 1 + configs/am62x_evm_a53_defconfig | 35 +++- configs/am62x_evm_r5_usbdfu_defconfig | 116 ++++++++++++ drivers/timer/omap-timer.c | 1 + drivers/usb/dwc3/Kconfig | 14 ++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-am62.c | 127 +++++++++++++ include/configs/am62x_evm.h | 10 +- 15 files changed, 701 insertions(+), 92 deletions(-) create mode 100644 configs/am62x_evm_r5_usbdfu_defconfig create mode 100644 drivers/usb/dwc3/dwc3-am62.c -- 2.40.0

9 23

[PATCH v4 0/5] fs/erofs: new filesystem
by Huang Jianan 28 May '24

28 May '24

Changes since v3: - update tools/docker/Dockerfile; Changes since v2: - sync up with erofs-utils 1.4; - update lib/lz4 to v1.8.3; - add test for filesystem functions; Changes since v1: - fix the inconsistency between From and SoB; - add missing license header; Huang Jianan (5): fs/erofs: add erofs filesystem support lib/lz4: update LZ4 decompressor module fs/erofs: add lz4 decompression support fs/erofs: add filesystem commands test/py: Add tests for the erofs MAINTAINERS | 9 + cmd/Kconfig | 6 + cmd/Makefile | 1 + cmd/erofs.c | 42 ++ configs/sandbox_defconfig | 1 + fs/Kconfig | 2 + fs/Makefile | 1 + fs/erofs/Kconfig | 21 + fs/erofs/Makefile | 9 + fs/erofs/data.c | 311 +++++++++++++ fs/erofs/decompress.c | 78 ++++ fs/erofs/decompress.h | 24 + fs/erofs/erofs_fs.h | 436 ++++++++++++++++++ fs/erofs/fs.c | 267 +++++++++++ fs/erofs/internal.h | 313 +++++++++++++ fs/erofs/namei.c | 252 +++++++++++ fs/erofs/super.c | 105 +++++ fs/erofs/zmap.c | 601 ++++++++++++++++++++++++ fs/fs.c | 22 + include/erofs.h | 19 + include/fs.h | 1 + include/u-boot/lz4.h | 49 ++ lib/lz4.c | 679 ++++++++++++++++++++-------- lib/lz4_wrapper.c | 23 +- test/py/tests/test_fs/test_erofs.py | 211 +++++++++ tools/docker/Dockerfile | 1 + 26 files changed, 3269 insertions(+), 215 deletions(-) create mode 100644 cmd/erofs.c create mode 100644 fs/erofs/Kconfig create mode 100644 fs/erofs/Makefile create mode 100644 fs/erofs/data.c create mode 100644 fs/erofs/decompress.c create mode 100644 fs/erofs/decompress.h create mode 100644 fs/erofs/erofs_fs.h create mode 100644 fs/erofs/fs.c create mode 100644 fs/erofs/internal.h create mode 100644 fs/erofs/namei.c create mode 100644 fs/erofs/super.c create mode 100644 fs/erofs/zmap.c create mode 100644 include/erofs.h create mode 100644 test/py/tests/test_fs/test_erofs.py -- 2.25.1

5 20

rk3399 issue: no DMA in Linux with mainline TF-A and U-Boot SPL
by Christoph Fritz 24 Apr '24

24 Apr '24

Hello Kever, on a rk3399, booting current U-Boot SPL with mainline TF-A leads to missing DMA (and no sound) on Linux. However, when using rockchip its so called mini-loader (rk3399_miniloader_v1.26.bin) and their BL31 (rk3399_bl31_v1.35.elf) to boot, DMA works perfectly fine. Tested on a custom rk3399 board and on ROCK Pi4. Attached to this mail are two boot logs with some debug prints: - good_amba_log.txt (DMA works) - no_amba_log.txt (no DMA device) The main difference I can spot between the two logs is that on Linux (drivers/amba/bus.c) AMBA_CID (0xb105f00d) cannot be found. Instead, only some CORESIGHT_CIDs (presumably for debugging) and four 0x00000000 CIDs are detected. As a result, the "PL330 DMAC-241330" driver does not load. My theory is that DMA needs to be allowed somewhere in the undocumented syscon- registers, similar to what U-Boot is already doing for eMMC in arch_cpu_init() (arch/arm/mach-rockchip/rk3399/rk3399.c). Any ideas? Or maybe I'm just missing some configuration? Since multiple software projects are involved (TF-A, OP-TEE, U-Boot, Linux), I Cc'ed a bit. Thanks -- Christoph

4 6

[PATCH] drivers: pinctrl-sunxi: add suniv spi1 function
by 路辉 19 Apr '24

19 Apr '24

>From 570b40e19de75511d9ce066e1a28333ada04baf2 Mon Sep 17 00:00:00 2001 From: Lu Hui <luhux76(a)gmail.com> Date: Mon, 29 May 2023 22:26:25 +0800 Subject: [PATCH] drivers: pinctrl-sunxi: add suniv spi1 function --- drivers/pinctrl/sunxi/pinctrl-sunxi.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/pinctrl/sunxi/pinctrl-sunxi.c b/drivers/pinctrl/sunxi/pinctrl-sunxi.c index e510218090..c448e40ab0 100644 --- a/drivers/pinctrl/sunxi/pinctrl-sunxi.c +++ b/drivers/pinctrl/sunxi/pinctrl-sunxi.c @@ -240,6 +240,7 @@ static const struct sunxi_pinctrl_function suniv_f1c100s_pinctrl_functions[] = { { "mmc0", 2 }, /* PF0-PF5 */ { "mmc1", 3 }, /* PC0-PC2 */ { "spi0", 2 }, /* PC0-PC3 */ + { "spi1", 6 }, /* PA0-PA3 */ #if IS_ENABLED(CONFIG_UART0_PORT_F) { "uart0", 3 }, /* PF2-PF4 */ #else -- 2.40.1

2 1

[Patch] net: dwc_eth_qos - works with fixed-phy
by Elmar Psilog 17 Apr '24

17 Apr '24

Let the EQoS in imx8mp handle fixed-phy too. Without that patch it lost track to the node to scan speed and duplex. Patch was created by Marek Vasut, just tested by me. Signed-off-by: Elmar Psilog <epsi at gmx.de> --- drivers/net/dwc_eth_qos.c 1 file changed diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c index afc47b56ff..10915d8e47 100644 --- a/drivers/net/dwc_eth_qos.c +++ b/drivers/net/dwc_eth_qos.c @@ -785,9 +785,21 @@ static int eqos_start(struct udevice *dev) */ if (!eqos->phy) { int addr = -1; - addr = eqos_get_phy_addr(eqos, dev); - eqos->phy = phy_connect(eqos->mii, addr, dev, - eqos->config->interface(dev)); + ofnode fixed_node; + + if (IS_ENABLED(CONFIG_PHY_FIXED)) { + fixed_node = ofnode_find_subnode(dev_ofnode(dev), + "fixed-link"); + if (ofnode_valid(fixed_node)) { + eqos->phy = fixed_phy_create(dev_ofnode(dev)); + eqos->phy_of_node = fixed_node; + } + } + if (!eqos->phy) { + addr = eqos_get_phy_addr(eqos, dev); + eqos->phy = phy_connect(eqos->mii, addr, dev, eqos->config->interface(dev)); + } + if (!eqos->phy) { pr_err("phy_connect() failed"); goto err_stop_resets;

4 7

[PATCH 0/8] SUNIV SPI NAND support in SPL
by Icenowy Zheng 11 Apr '24

11 Apr '24

This patchset tries to extend SPI-based boot code in sunxi SPL to support SPI NAND, following the same principle with current SPI NOR code (mimicking the behavior of sunxi BROM). In addition, as part of test to this patchset, some patches for Source Parts Inc. PopStick is attached, although marked DO NOT MERGE because the DT should come from Linux after it's ready. To keep thr code that accesses SPI NAND as simple as possible, it assumes fixed page size, which is also what sunxi BROM does. The SUNIV SPL assumes 0x400 page size, but here to utilize the space better, in the attached example of PopStick, U-Boot main part is assumed to be with 0x800 page size (which is the real situation of the W25N01 flash used by PopStick). Icenowy Zheng (8): sunxi: SPL SPI: extract code for doing SPI transfer sunxi: SPL SPI: add support for read command with 2 byte address sunxi: SPL SPI: allow multiple boot attempt sunxi: SPL SPI: add initial support for booting from SPI NAND sunxi: enable support for SPI NAND booting on SUNIV [DO NOT MERGE] sunxi: sync DT from my tree for PopStick [DO NOT MERGE, DIRTY HACK] sunxi: use UBI for environement storage [DO NOT MERGE] sunxi: add a defconfig for PopStick arch/arm/dts/Makefile | 3 +- arch/arm/dts/suniv-f1c100s-licheepi-nano.dts | 16 ++ arch/arm/dts/suniv-f1c100s.dtsi | 26 ++ arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts | 101 ++++++++ arch/arm/mach-sunxi/Kconfig | 16 ++ arch/arm/mach-sunxi/board.c | 4 +- arch/arm/mach-sunxi/spl_spi_sunxi.c | 247 ++++++++++++++----- board/sunxi/board.c | 1 + configs/popstick_defconfig | 35 +++ 9 files changed, 377 insertions(+), 72 deletions(-) create mode 100644 arch/arm/dts/suniv-f1c200s-popstick-v1.1.dts create mode 100644 configs/popstick_defconfig -- 2.37.1

5 21

[PATCH] clk: imx8mp: add pwm clocks support
by Tommaso Merciai 11 Apr '24

11 Apr '24

Add clocks support for the PWM controllers. This is ported from Linux v6.3.0-rc1 Signed-off-by: Tommaso Merciai <tomm.merciai(a)gmail.com> --- drivers/clk/imx/clk-imx8mp.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c index ffbc1d1ba9..fac87ff505 100644 --- a/drivers/clk/imx/clk-imx8mp.c +++ b/drivers/clk/imx/clk-imx8mp.c @@ -122,6 +122,22 @@ static const char *imx8mp_gic_sels[] = {"clock-osc-24m", "sys_pll2_200m", "sys_p "sys_pll2_100m", "sys_pll1_800m", "sys_pll2_500m", "clk_ext4", "audio_pll2_out" }; +static const char * const imx8mp_pwm1_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_pll1_160m", + "sys_pll1_40m", "sys_pll3_out", "clk_ext1", + "sys_pll1_80m", "video_pll1_out", }; + +static const char * const imx8mp_pwm2_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_pll1_160m", + "sys_pll1_40m", "sys_pll3_out", "clk_ext1", + "sys_pll1_80m", "video_pll1_out", }; + +static const char * const imx8mp_pwm3_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_pll1_160m", + "sys_pll1_40m", "sys_pll3_out", "clk_ext2", + "sys_pll1_80m", "video_pll1_out", }; + +static const char * const imx8mp_pwm4_sels[] = {"clock-osc-24m", "sys_pll2_100m", "sys_pll1_160m", + "sys_pll1_40m", "sys_pll3_out", "clk_ext2", + "sys_pll1_80m", "video_pll1_out", }; + static const char *imx8mp_ecspi1_sels[] = {"clock-osc-24m", "sys_pll2_200m", "sys_pll1_40m", "sys_pll1_160m", "sys_pll1_800m", "sys_pll3_out", "sys_pll2_250m", "audio_pll2_out", }; @@ -270,6 +286,10 @@ static int imx8mp_clk_probe(struct udevice *dev) clk_dm(IMX8MP_CLK_GIC, imx8m_clk_composite_critical("gic", imx8mp_gic_sels, base + 0xb200)); clk_dm(IMX8MP_CLK_ECSPI1, imx8m_clk_composite("ecspi1", imx8mp_ecspi1_sels, base + 0xb280)); clk_dm(IMX8MP_CLK_ECSPI2, imx8m_clk_composite("ecspi2", imx8mp_ecspi2_sels, base + 0xb300)); + clk_dm(IMX8MP_CLK_PWM1, imx8m_clk_composite_critical("pwm1", imx8mp_pwm1_sels, base + 0xb380)); + clk_dm(IMX8MP_CLK_PWM2, imx8m_clk_composite_critical("pwm2", imx8mp_pwm2_sels, base + 0xb400)); + clk_dm(IMX8MP_CLK_PWM3, imx8m_clk_composite_critical("pwm3", imx8mp_pwm3_sels, base + 0xb480)); + clk_dm(IMX8MP_CLK_PWM4, imx8m_clk_composite_critical("pwm4", imx8mp_pwm4_sels, base + 0xb500)); clk_dm(IMX8MP_CLK_ECSPI3, imx8m_clk_composite("ecspi3", imx8mp_ecspi3_sels, base + 0xc180)); clk_dm(IMX8MP_CLK_WDOG, imx8m_clk_composite("wdog", imx8mp_wdog_sels, base + 0xb900)); @@ -292,6 +312,10 @@ static int imx8mp_clk_probe(struct udevice *dev) clk_dm(IMX8MP_CLK_I2C2_ROOT, imx_clk_gate4("i2c2_root_clk", "i2c2", base + 0x4180, 0)); clk_dm(IMX8MP_CLK_I2C3_ROOT, imx_clk_gate4("i2c3_root_clk", "i2c3", base + 0x4190, 0)); clk_dm(IMX8MP_CLK_I2C4_ROOT, imx_clk_gate4("i2c4_root_clk", "i2c4", base + 0x41a0, 0)); + clk_dm(IMX8MP_CLK_PWM1_ROOT, imx_clk_gate4("pwm1_root_clk", "pwm1", base + 0x4280, 0)); + clk_dm(IMX8MP_CLK_PWM2_ROOT, imx_clk_gate4("pwm2_root_clk", "pwm2", base + 0x4290, 0)); + clk_dm(IMX8MP_CLK_PWM3_ROOT, imx_clk_gate4("pwm3_root_clk", "pwm3", base + 0x42a0, 0)); + clk_dm(IMX8MP_CLK_PWM4_ROOT, imx_clk_gate4("pwm4_root_clk", "pwm4", base + 0x42b0, 0)); clk_dm(IMX8MP_CLK_QSPI_ROOT, imx_clk_gate4("qspi_root_clk", "qspi", base + 0x42f0, 0)); clk_dm(IMX8MP_CLK_I2C5_ROOT, imx_clk_gate2("i2c5_root_clk", "i2c5", base + 0x4330, 0)); clk_dm(IMX8MP_CLK_I2C6_ROOT, imx_clk_gate2("i2c6_root_clk", "i2c6", base + 0x4340, 0)); -- 2.34.1

2 2

[PATCH 00/33] doc: board: amlogic: spring clean-up of Amlogic docs
by Christian Hewitt 05 Apr '24

05 Apr '24

Amlogic documentation spans U-Boot support from 2015-current resulting in older content being harder to follow. And due to many international contributors the docs also contain grammar quirks. This series reworks all board documents to be more consistent. There is deliberate emphasis on using the amlogic-boot-fip repo for signing tasks as this is easier for most users to follow. The original/longer signing process (described as Manual Signing) has been tidied up. In the index.rst file I've dropped board names from the features table as this adds considerable width and makes adding new boards a fiddly process. I've appended the SoC type to the boader header so it shows in the TOC list to retain a reference between boards and the table. I've added missing board docs for GS-King-X, BPI-M5, BPI-CM4IO, and we split ODROID-HC4 into its own document. It originally followed the same process as the ODROID0-C4, but now has a separate defconfig to enable SPI-NOR and PCIe SATA support. Users occasionally follow the current doc and build U-Boot for the C4 which omits this and then struggle to figure out why SATA boot doesn't work when wiki/forums say it does. There are other minor cleanups and tweaks for clarity of simply more up-to-date information for a board or process. Please review and flag any omissions or issues! Christian Hewitt (33): doc: boards: amlogic: update documentation for index page doc: boards: amlogic: update documentation for boot-flow doc: boards: amlogic: update documentation for pre-generated-fip's doc: boards: amlogic: update documentation for Beelink GT-King doc: boards: amlogic: update documentation for Beelink GT-King Pro doc: boards: amlogic: update documentation for JetHub J100 doc: boards: amlogic: update documentation for JetHub J80 doc: boards: amlogic: update documentation for Khadas VIM doc: boards: amlogic: update documentation for Khadas VIM2 doc: boards: amlogic: update documentation for Khadas VIM3 doc: boards: amlogic: update documentation for Khadas VIM3L doc: boards: amlogic: update documentation for LaFrite doc: boards: amlogic: update documentation for LePotato doc: boards: amlogic: update documentation for NanoPi-K2 doc: boards: amlogic: update documentation for ODROID-C2 doc: boards: amlogic: update documentation for ODROID-C4 doc: boards: amlogic: update documentation for ODROID GO ULTRA doc: boards: amlogic: update documentation for ODROID-N2/N2+ doc: boards: amlogic: update documentation for ODROID-N2L doc: boards: amlogic: update documentation for P200 doc: boards: amlogic: update documentation for P201 doc: boards: amlogic: update documentation for Q200 doc: boards: amlogic: update documentation for Radxa Zero doc: boards: amlogic: update documentation for S400 doc: boards: amlogic: update documentation for SEI510 doc: boards: amlogic: update documentation for SEI610 doc: boards: amlogic: update documentation for U200 doc: boards: amlogic: update documentation for W400 doc: boards: amlogic: update documentation for WeTek Core2 doc: boards: amlogic: add documentation for BananaPi CM4IO doc: boards: amlogic: add documentation for BananaPi M5 doc: boards: amlogic: add documentation for GS-King-X doc: boards: amlogic: add documentation for ODROID-HC4 board/amlogic/beelink-s922x/MAINTAINERS | 3 +- board/amlogic/u200/MAINTAINERS | 1 - board/amlogic/w400/MAINTAINERS | 2 + doc/board/amlogic/bananapi-cm4io.rst | 152 ++++++++++++++++++++ doc/board/amlogic/bananapi-m5.rst | 141 +++++++++++++++++++ doc/board/amlogic/beelink-gskingx.rst | 121 ++++++++++++++++ doc/board/amlogic/beelink-gtking.rst | 120 ++++++++-------- doc/board/amlogic/beelink-gtkingpro.rst | 120 ++++++++-------- doc/board/amlogic/boot-flow.rst | 178 ++++++++++++------------ doc/board/amlogic/index.rst | 141 +++++++++---------- doc/board/amlogic/jethub-j100.rst | 66 ++++----- doc/board/amlogic/jethub-j80.rst | 46 +++--- doc/board/amlogic/khadas-vim.rst | 76 +++++----- doc/board/amlogic/khadas-vim2.rst | 76 +++++----- doc/board/amlogic/khadas-vim3.rst | 137 +++++++++--------- doc/board/amlogic/khadas-vim3l.rst | 137 +++++++++--------- doc/board/amlogic/libretech-ac.rst | 77 +++++----- doc/board/amlogic/libretech-cc.rst | 109 ++++++--------- doc/board/amlogic/nanopi-k2.rst | 93 +++++++------ doc/board/amlogic/odroid-c2.rst | 54 +++---- doc/board/amlogic/odroid-c4.rst | 117 ++++++++-------- doc/board/amlogic/odroid-go-ultra.rst | 25 +++- doc/board/amlogic/odroid-hc4.rst | 141 +++++++++++++++++++ doc/board/amlogic/odroid-n2.rst | 122 ++++++++-------- doc/board/amlogic/odroid-n2l.rst | 33 +++-- doc/board/amlogic/p200.rst | 87 +++++++----- doc/board/amlogic/p201.rst | 87 +++++++----- doc/board/amlogic/pre-generated-fip.rst | 138 +++++++++++------- doc/board/amlogic/q200.rst | 76 +++++----- doc/board/amlogic/radxa-zero.rst | 45 +++--- doc/board/amlogic/s400.rst | 89 ++++++------ doc/board/amlogic/sei510.rst | 113 ++++++++------- doc/board/amlogic/sei610.rst | 118 ++++++++-------- doc/board/amlogic/u200.rst | 113 ++++++++------- doc/board/amlogic/w400.rst | 115 ++++++++------- doc/board/amlogic/wetek-core2.rst | 83 ++++++----- 36 files changed, 2042 insertions(+), 1310 deletions(-) create mode 100644 doc/board/amlogic/bananapi-cm4io.rst create mode 100644 doc/board/amlogic/bananapi-m5.rst create mode 100644 doc/board/amlogic/beelink-gskingx.rst create mode 100644 doc/board/amlogic/odroid-hc4.rst -- 2.34.1

5 41