June 2022 - U-Boot

[PATCH 01/10] i2c: stm32: add support for the st,stm32mp13 SOC
by Patrick Delaunay 30 Jun '22

30 Jun '22

The stm32mp13 soc differs from the stm32mp15 in terms of clear register offset for controlling the FMP (Fast Mode Plus). Signed-off-by: Patrick Delaunay <patrick.delaunay(a)foss.st.com> --- (no changes since v1) drivers/i2c/stm32f7_i2c.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/i2c/stm32f7_i2c.c b/drivers/i2c/stm32f7_i2c.c index c6ae65badb7..bf2a6c9b4bd 100644 --- a/drivers/i2c/stm32f7_i2c.c +++ b/drivers/i2c/stm32f7_i2c.c @@ -267,6 +267,10 @@ static const struct stm32_i2c_data stm32mp15_data = { .fmp_clr_offset = 0x40, }; +static const struct stm32_i2c_data stm32mp13_data = { + .fmp_clr_offset = 0x4, +}; + static int stm32_i2c_check_device_busy(struct stm32_i2c_priv *i2c_priv) { struct stm32_i2c_regs *regs = i2c_priv->regs; @@ -957,6 +961,7 @@ static const struct dm_i2c_ops stm32_i2c_ops = { static const struct udevice_id stm32_i2c_of_match[] = { { .compatible = "st,stm32f7-i2c", .data = (ulong)&stm32f7_data }, { .compatible = "st,stm32mp15-i2c", .data = (ulong)&stm32mp15_data }, + { .compatible = "st,stm32mp13-i2c", .data = (ulong)&stm32mp13_data }, {} }; -- 2.25.1

2 10

xilinx uboot gpio ctrl
by 张鹏 30 Jun '22

30 Jun '22

Hi, https://github.com/Xilinx/u-boot-xlnx My device is ad9361+7z035,when I tested the led, I found that the gpio pin value cannot be changed. leds(gpio) : 58 59 60 61 (Works no problem in linux system) cmd: gpio s 58 gpio: pin 58 (gpio 58) value is 1 Warning: value of pin is still 0 gpio status -a 58 58: output: 0 [ ] When using gpio command to set gpio58, its mode is changed from input to output, but the pin value is always 0.

1 0

[PATCH 1/8] env: Do not make CONFIG_EXTRA_ENV_TEXT and CONFIG_EXTRA_ENV_SETTINGS conflict
by Tom Rini 29 Jun '22

29 Jun '22

Largely, the use of CONFIG_EXTRA_ENV_SETTINGS can be migrated directly to come from CONFIG_EXTRA_ENV_TEXT. The biggest case that cannot easily be migrated is distro_bootcmd support. Rather than block migration on this, remove the #error here so that we can being moving forward. Cc: Joe Hershberger <joe.hershberger(a)ni.com> Cc: Wolfgang Denk <wd(a)denx.de> Cc: Simon Glass <sjg(a)chromium.org> Signed-off-by: Tom Rini <trini(a)konsulko.com> --- I spent about a day working at getting config_distro_bootcmd to work via CONFIG_EXTRA_ENV_TEXT and _maybe_ there's a path forward if we rely on less nesting of macros, I'm not convinced. But I can clearly see how moving everything else forward to text based environment files will encourage sharing of environment and both remove otherwise unmigrated CONFIG symbols and generally move forward with being able to remove include/config/board.h files. --- include/env_default.h | 3 --- 1 file changed, 3 deletions(-) diff --git a/include/env_default.h b/include/env_default.h index 7004a6fef29b..7113e08e6b0f 100644 --- a/include/env_default.h +++ b/include/env_default.h @@ -109,9 +109,6 @@ const char default_environment[] = { "bootlimit=" __stringify(CONFIG_BOOTCOUNT_BOOTLIMIT)"\0" #endif #ifdef CONFIG_EXTRA_ENV_TEXT -# ifdef CONFIG_EXTRA_ENV_SETTINGS -# error "Your board uses a text-file environment, so must not define CONFIG_EXTRA_ENV_SETTINGS" -# endif /* This is created in the Makefile */ CONFIG_EXTRA_ENV_TEXT #endif -- 2.25.1

2 13

[PATCH 1/8] Convert CONFIG_ENV_MIN_ENTRIES et al to Kconfig
by Tom Rini 29 Jun '22

29 Jun '22

This converts the following to Kconfig: CONFIG_ENV_MIN_ENTRIES CONFIG_ENV_MAX_ENTRIES Cc: Michal Simek <michal.simek(a)amd.com> Signed-off-by: Tom Rini <trini(a)konsulko.com> --- I'm not 100% sure that what was being done in xilinx_zynqmp.h was working before this change. If we _need_ to tweak this value down in SPL we need to introduce CONFIG_SPL_ENV_{MIN,MAX}_ENTRIES and use CONFIG_VAL() in the code. --- README | 8 -------- configs/clearfog_defconfig | 1 + configs/helios4_defconfig | 1 + env/Kconfig | 16 ++++++++++++++++ include/configs/clearfog.h | 2 -- include/configs/helios4.h | 2 -- include/configs/xilinx_zynqmp.h | 5 ----- lib/hashtable.c | 7 ------- 8 files changed, 18 insertions(+), 24 deletions(-) diff --git a/README b/README index 841f8ce082c0..7649dae36338 100644 --- a/README +++ b/README @@ -1877,14 +1877,6 @@ Configuration Settings: while unprotecting/erasing/programming. Please only enable this option if you really know what you are doing. -- CONFIG_ENV_MAX_ENTRIES - - Maximum number of entries in the hash table that is used - internally to store the environment settings. The default - setting is supposed to be generous and should work in most - cases. This setting can be used to tune behaviour; see - lib/hashtable.c for details. - - CONFIG_ENV_FLAGS_LIST_DEFAULT - CONFIG_ENV_FLAGS_LIST_STATIC Enable validation of the values given to environment variables when diff --git a/configs/clearfog_defconfig b/configs/clearfog_defconfig index bec36beb8554..1ee0c6637573 100644 --- a/configs/clearfog_defconfig +++ b/configs/clearfog_defconfig @@ -50,6 +50,7 @@ CONFIG_CMD_TIME=y CONFIG_CMD_MVEBU_BUBT=y # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_MIN_ENTRIES=128 CONFIG_ARP_TIMEOUT=200 CONFIG_NET_RETRY_COUNT=50 CONFIG_NET_RANDOM_ETHADDR=y diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig index 2a1db65d1bfd..4642eb1ccb25 100644 --- a/configs/helios4_defconfig +++ b/configs/helios4_defconfig @@ -51,6 +51,7 @@ CONFIG_CMD_TIME=y CONFIG_CMD_MVEBU_BUBT=y # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_MIN_ENTRIES=128 CONFIG_ARP_TIMEOUT=200 CONFIG_NET_RETRY_COUNT=50 CONFIG_NET_RANDOM_ETHADDR=y diff --git a/env/Kconfig b/env/Kconfig index 2f625b22575a..0aed7aea46bc 100644 --- a/env/Kconfig +++ b/env/Kconfig @@ -30,6 +30,22 @@ config ENV_OVERWRITE Use this to permit overriding of certain environmental variables like Ethernet and Serial +config ENV_MIN_ENTRIES + int "Minimum number of entries in the environment hashtable" + default 64 + help + Minimum number of entries in the hash table that is used internally + to store the environment settings. + +config ENV_MAX_ENTRIES + int "Maximumm number of entries in the environment hashtable" + default 512 + help + Maximum number of entries in the hash table that is used internally + to store the environment settings. The default setting is supposed to + be generous and should work in most cases. This setting can be used + to tune behaviour; see lib/hashtable.c for details. + config ENV_IS_NOWHERE bool "Environment is not stored" default y if !ENV_IS_IN_EEPROM && !ENV_IS_IN_EXT4 && \ diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h index af04352eda3b..9969269bf2ac 100644 --- a/include/configs/clearfog.h +++ b/include/configs/clearfog.h @@ -18,8 +18,6 @@ * U-Boot into it. */ -#define CONFIG_ENV_MIN_ENTRIES 128 - /* Environment in MMC */ /* * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC diff --git a/include/configs/helios4.h b/include/configs/helios4.h index cae20073584c..ff2c50644326 100644 --- a/include/configs/helios4.h +++ b/include/configs/helios4.h @@ -18,8 +18,6 @@ * U-Boot into it. */ -#define CONFIG_ENV_MIN_ENTRIES 128 - /* Environment in MMC */ /* * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC diff --git a/include/configs/xilinx_zynqmp.h b/include/configs/xilinx_zynqmp.h index 20515b4e26ac..4e71a42cd346 100644 --- a/include/configs/xilinx_zynqmp.h +++ b/include/configs/xilinx_zynqmp.h @@ -207,11 +207,6 @@ /* ATF is my kernel image */ -#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_DFU) -# define CONFIG_SPL_HASH -# define CONFIG_ENV_MAX_ENTRIES 10 -#endif - #ifdef CONFIG_SPL_SYS_MALLOC_SIMPLE # error "Disable CONFIG_SPL_SYS_MALLOC_SIMPLE. Full malloc needs to be used" #endif diff --git a/lib/hashtable.c b/lib/hashtable.c index ff5ff7263949..90c8465611e9 100644 --- a/lib/hashtable.c +++ b/lib/hashtable.c @@ -35,13 +35,6 @@ # include <linux/ctype.h> #endif -#ifndef CONFIG_ENV_MIN_ENTRIES /* minimum number of entries */ -#define CONFIG_ENV_MIN_ENTRIES 64 -#endif -#ifndef CONFIG_ENV_MAX_ENTRIES /* maximum number of entries */ -#define CONFIG_ENV_MAX_ENTRIES 512 -#endif - #define USED_FREE 0 #define USED_DELETED -1 -- 2.25.1

2 9

[PATCH 01/15] xtensa: Switch to using CONFIG_XTENSA for building device trees
by Tom Rini 29 Jun '22

29 Jun '22

The only use of CONFIG_XTFPGA was to build all of the in-tree device trees. Switch to using CONFIG_XTENSA instead of a non-Kconfig symbol. Signed-off-by: Tom Rini <trini(a)konsulko.com> --- arch/xtensa/dts/Makefile | 2 +- include/configs/xtfpga.h | 6 ------ 2 files changed, 1 insertion(+), 7 deletions(-) diff --git a/arch/xtensa/dts/Makefile b/arch/xtensa/dts/Makefile index fbbdefaf2cf1..c22c50ac4e5d 100644 --- a/arch/xtensa/dts/Makefile +++ b/arch/xtensa/dts/Makefile @@ -1,6 +1,6 @@ # SPDX-License-Identifier: GPL-2.0+ -dtb-$(CONFIG_XTFPGA) += ml605.dtb ml605_nommu.dtb kc705.dtb kc705_nommu.dtb +dtb-$(CONFIG_XTENSA) += ml605.dtb ml605_nommu.dtb kc705.dtb kc705_nommu.dtb include $(srctree)/scripts/Makefile.dts diff --git a/include/configs/xtfpga.h b/include/configs/xtfpga.h index 7392582b5e46..f1ea47654671 100644 --- a/include/configs/xtfpga.h +++ b/include/configs/xtfpga.h @@ -16,12 +16,6 @@ * differences. */ -/*=====================*/ -/* Board and Processor */ -/*=====================*/ - -#define CONFIG_XTFPGA - /*===================*/ /* RAM Layout */ /*===================*/ -- 2.25.1

2 18

[PATCH] mtd: mxs_nand_spl: fix nand_command protocol violation
by Michael Trimarchi 29 Jun '22

29 Jun '22

From: Andrea Scian <andrea.scian(a)dave.eu> mxs_nand_command() implementation assume that it's working with a LP NAND, which is a common case nowadays and thus uses two bytes for column address. However this is wrong for NAND_CMD_READID and NAND_CMD_PARAM, which expects only one byte of column address, even for LP NANDs. This leads to ONFI detection problem with some NAND manufacturer (like Winbond) but not with others (like Samsung and Spansion) We fix this with a simple workaround to avoid the 2nd byte column address for those two commands. Also align the code with nand_base to support 16 bit devices. Tested on an iMX6SX device with: * Winbond W29N04GVSIAA * Spansion S34ML04G100TF100 * Samsung K9F4G08U00 Tested on imx8mn device with: * Windbond W29N04GV Signed-off-by: Andrea Scian <andrea.scian(a)dave.eu> CC: Stefano Babic <sbabic(a)denx.de> Signed-off-by: Michael Trimarchi <michael(a)amarulasolutions.com> --- drivers/mtd/nand/raw/mxs_nand_spl.c | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/nand/raw/mxs_nand_spl.c b/drivers/mtd/nand/raw/mxs_nand_spl.c index 2bfb181007..3daacbb330 100644 --- a/drivers/mtd/nand/raw/mxs_nand_spl.c +++ b/drivers/mtd/nand/raw/mxs_nand_spl.c @@ -29,8 +29,20 @@ static void mxs_nand_command(struct mtd_info *mtd, unsigned int command, /* Serially input address */ if (column != -1) { + /* Adjust columns for 16 bit buswidth */ + if (chip->options & NAND_BUSWIDTH_16 && + !nand_opcode_8bits(command)) + column >>= 1; chip->cmd_ctrl(mtd, column, NAND_ALE); - chip->cmd_ctrl(mtd, column >> 8, NAND_ALE); + + /* + * Assume LP NAND here, so use two bytes column address + * but not for CMD_READID and CMD_PARAM, which require + * only one byte column address + */ + if (command != NAND_CMD_READID && + command != NAND_CMD_PARAM) + chip->cmd_ctrl(mtd, column >> 8, NAND_ALE); } if (page_addr != -1) { chip->cmd_ctrl(mtd, page_addr, NAND_ALE); -- 2.25.1

4 3

[PATCH] mmc: zynq_sdhci: Fix timing macros for MMC High speed
by Ashok Reddy Soma 29 Jun '22

29 Jun '22

Timing macro's are wrong for MMC_HS_52 and MMC_DDR_52. Fix it with correct values of MMC_TIMING_MMC_HS and MMC_TIMING_MMC_DDR52 respectively. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma(a)xilinx.com> --- drivers/mmc/zynq_sdhci.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/mmc/zynq_sdhci.c b/drivers/mmc/zynq_sdhci.c index e978b67988..8f4071c8c2 100644 --- a/drivers/mmc/zynq_sdhci.c +++ b/drivers/mmc/zynq_sdhci.c @@ -101,8 +101,8 @@ static const u8 mode2timing[] = { [MMC_LEGACY] = MMC_TIMING_LEGACY, [MMC_HS] = MMC_TIMING_MMC_HS, [SD_HS] = MMC_TIMING_SD_HS, - [MMC_HS_52] = MMC_TIMING_UHS_SDR50, - [MMC_DDR_52] = MMC_TIMING_UHS_DDR50, + [MMC_HS_52] = MMC_TIMING_MMC_HS, + [MMC_DDR_52] = MMC_TIMING_MMC_DDR52, [UHS_SDR12] = MMC_TIMING_UHS_SDR12, [UHS_SDR25] = MMC_TIMING_UHS_SDR25, [UHS_SDR50] = MMC_TIMING_UHS_SDR50, -- 2.17.1

2 1

[PATCH] board/BuR/*: replace maintainer of BuR board
by Hannes Schmelzer 29 Jun '22

29 Jun '22

Since i'm leaving the company with end of june, the maintainership will be transferred to Wolfgang Wallner. Signed-off-by: Hannes Schmelzer <hannes.schmelzer(a)br-automation.com> Seriec-cc: trini(a)konsulko.com --- board/BuR/brppt1/MAINTAINERS | 2 +- board/BuR/brppt2/MAINTAINERS | 2 +- board/BuR/brsmarc1/MAINTAINERS | 2 +- board/BuR/brxre1/MAINTAINERS | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/board/BuR/brppt1/MAINTAINERS b/board/BuR/brppt1/MAINTAINERS index 9eddab4..b49b008 100644 --- a/board/BuR/brppt1/MAINTAINERS +++ b/board/BuR/brppt1/MAINTAINERS @@ -1,5 +1,5 @@ BRPPT1 BOARD -M: Hannes Schmelzer <hannes.schmelzer(a)br-automation.com> +M: Wolfgang Wallner <wolgang.wallner(a)br-automation.com> S: Maintained F: board/BuR/brppt1/ F: include/configs/brppt1.h diff --git a/board/BuR/brppt2/MAINTAINERS b/board/BuR/brppt2/MAINTAINERS index a1b5bd4..3b81953 100644 --- a/board/BuR/brppt2/MAINTAINERS +++ b/board/BuR/brppt2/MAINTAINERS @@ -1,5 +1,5 @@ BUR_PPT2 BOARD -M: Hannes Schmelzer <hannes.schmelzer(a)br-automation.com> +M: Wolfgang Wallner <wolgang.wallner(a)br-automation.com> S: Maintained F: board/BuR/brppt2/ F: include/configs/brppt2.h diff --git a/board/BuR/brsmarc1/MAINTAINERS b/board/BuR/brsmarc1/MAINTAINERS index c6dfc20..f1d4232 100644 --- a/board/BuR/brsmarc1/MAINTAINERS +++ b/board/BuR/brsmarc1/MAINTAINERS @@ -1,5 +1,5 @@ BRSMARC1 BOARD -M: Hannes Schmelzer <hannes.schmelzer(a)br-automation.com> +M: Wolfgang Wallner <wolgang.wallner(a)br-automation.com> S: Maintained F: board/BuR/brsmarc1/ F: include/configs/brsmarc1.h diff --git a/board/BuR/brxre1/MAINTAINERS b/board/BuR/brxre1/MAINTAINERS index eb0fe8b..c7f7b81 100644 --- a/board/BuR/brxre1/MAINTAINERS +++ b/board/BuR/brxre1/MAINTAINERS @@ -1,5 +1,5 @@ BRXRE1 BOARD -M: Hannes Schmelzer <hannes.schmelzer(a)br-automation.com> +M: Wolfgang Wallner <wolgang.wallner(a)br-automation.com> S: Maintained F: board/BuR/brxre1/ F: include/configs/brxre1.h -- 2.7.4

1 0

[PATCH v5 0/3] usb: add isp1760 hcd support
by Rui Miguel Silva 29 Jun '22

29 Jun '22

Add support for the usb isp1760 host controller family, which for example is present in MPS3 FPGA board from Arm (isp1763). First we move some helper functions and defines to a more common place to be shared by several urb users. (patch 1/3) Then add the driver itself, is a ported version of the kernel actual driver, which I am also the maintainer. (patch 2/3) And last, enable it for the corstone1000 platform that uses that MPS3 board for its implementation (patch 3/3). Cheers, Rui v4[4] -> v5: Marek: - fix makefile to include the common urb code for the musb_host, musb_gadget and r8a66597 drivers v3 -> v4: - rebase on top of next and resend with Marek in --to v2[3] -> v3: - when you think you have amend commit and fix stay uncommitted. s/[HC_FIELD_MAX] = {};/[HC_FIELD_MAX] = {},/ v1[0] -> v2: - gentle ping - merge fix from kernel upstream [1] PS: This should go on top of the corstone1000 platform enable series [2] 0: https://lore.kernel.org/u-boot/20220512142016.2025129-1-rui.silva@linaro.or… 1: https://lore.kernel.org/linux-usb/20220516091424.391209-1-linus.walleij@lin… 2: https://lore.kernel.org/u-boot/20220511095541.1461937-1-rui.silva@linaro.or… 3: https://lore.kernel.org/u-boot/20220523090119.1212016-1-rui.silva@linaro.or… 4: https://lore.kernel.org/u-boot/20220628174214.2496-1-rui.silva@linaro.org/T… Rui Miguel Silva (3): usb: common: move urb code to common usb: add isp1760 family driver corstone1000: enable isp1763 usb controller and mmc Makefile | 1 + configs/corstone1000_defconfig | 3 + drivers/usb/Kconfig | 2 + drivers/usb/common/Makefile | 4 + drivers/usb/common/usb_urb.c | 160 ++ drivers/usb/host/r8a66597-hcd.c | 30 +- drivers/usb/isp1760/Kconfig | 12 + drivers/usb/isp1760/Makefile | 6 + drivers/usb/isp1760/isp1760-core.c | 380 +++ drivers/usb/isp1760/isp1760-core.h | 96 + drivers/usb/isp1760/isp1760-hcd.c | 2477 +++++++++++++++++ drivers/usb/isp1760/isp1760-hcd.h | 81 + drivers/usb/isp1760/isp1760-if.c | 125 + drivers/usb/isp1760/isp1760-regs.h | 292 ++ drivers/usb/isp1760/isp1760-uboot.c | 75 + drivers/usb/isp1760/isp1760-uboot.h | 27 + drivers/usb/musb-new/musb_core.c | 2 +- drivers/usb/musb-new/musb_host.c | 2 +- drivers/usb/musb-new/musb_host.h | 2 +- drivers/usb/musb-new/musb_uboot.c | 38 +- drivers/usb/musb-new/musb_uboot.h | 2 +- include/configs/corstone1000.h | 6 + .../linux/usb/usb_urb_compat.h | 47 +- include/usb_defs.h | 32 + 24 files changed, 3826 insertions(+), 76 deletions(-) create mode 100644 drivers/usb/common/usb_urb.c create mode 100644 drivers/usb/isp1760/Kconfig create mode 100644 drivers/usb/isp1760/Makefile create mode 100644 drivers/usb/isp1760/isp1760-core.c create mode 100644 drivers/usb/isp1760/isp1760-core.h create mode 100644 drivers/usb/isp1760/isp1760-hcd.c create mode 100644 drivers/usb/isp1760/isp1760-hcd.h create mode 100644 drivers/usb/isp1760/isp1760-if.c create mode 100644 drivers/usb/isp1760/isp1760-regs.h create mode 100644 drivers/usb/isp1760/isp1760-uboot.c create mode 100644 drivers/usb/isp1760/isp1760-uboot.h rename drivers/usb/musb-new/usb-compat.h => include/linux/usb/usb_urb_compat.h (59%) -- 2.37.0

1 3

[PATCH v4 0/3] usb: add isp1760 hcd support
by Rui Miguel Silva 29 Jun '22

29 Jun '22

Add support for the usb isp1760 host controller family, which for example is present in MPS3 FPGA board from Arm (isp1763). First we move some helper functions and defines to a more common place to be shared by several urb users. (patch 1/3) Then add the driver itself, is a ported version of the kernel actual driver, which I am also the maintainer. (patch 2/3) And last, enable it for the corstone1000 platform that uses that MPS3 board for its implementation (patch 3/3). Cheers, Rui v3 -> v4: - rebase on top of next and resend with Marek in --to v2[3] -> v3: - when you think you have amend commit and fix stay uncommitted. s/[HC_FIELD_MAX] = {};/[HC_FIELD_MAX] = {},/ v1[0] -> v2: - gentle ping - merge fix from kernel upstream [1] PS: This should go on top of the corstone1000 platform enable series [2] 0: https://lore.kernel.org/u-boot/20220512142016.2025129-1-rui.silva@linaro.or… 1: https://lore.kernel.org/linux-usb/20220516091424.391209-1-linus.walleij@lin… 2: https://lore.kernel.org/u-boot/20220511095541.1461937-1-rui.silva@linaro.or… 3: https://lore.kernel.org/u-boot/20220523090119.1212016-1-rui.silva@linaro.or… Rui Miguel Silva (3): usb: common: move urb code to common usb: add isp1760 family driver corstone1000: enable isp1763 usb controller and mmc Makefile | 1 + configs/corstone1000_defconfig | 3 + drivers/usb/Kconfig | 2 + drivers/usb/common/Makefile | 3 + drivers/usb/common/usb_urb.c | 160 ++ drivers/usb/host/r8a66597-hcd.c | 30 +- drivers/usb/isp1760/Kconfig | 12 + drivers/usb/isp1760/Makefile | 6 + drivers/usb/isp1760/isp1760-core.c | 380 +++ drivers/usb/isp1760/isp1760-core.h | 96 + drivers/usb/isp1760/isp1760-hcd.c | 2477 +++++++++++++++++ drivers/usb/isp1760/isp1760-hcd.h | 81 + drivers/usb/isp1760/isp1760-if.c | 125 + drivers/usb/isp1760/isp1760-regs.h | 292 ++ drivers/usb/isp1760/isp1760-uboot.c | 75 + drivers/usb/isp1760/isp1760-uboot.h | 27 + drivers/usb/musb-new/musb_core.c | 2 +- drivers/usb/musb-new/musb_host.c | 2 +- drivers/usb/musb-new/musb_host.h | 2 +- drivers/usb/musb-new/musb_uboot.c | 38 +- drivers/usb/musb-new/musb_uboot.h | 2 +- include/configs/corstone1000.h | 6 + .../linux/usb/usb_urb_compat.h | 47 +- include/usb_defs.h | 32 + 24 files changed, 3825 insertions(+), 76 deletions(-) create mode 100644 drivers/usb/common/usb_urb.c create mode 100644 drivers/usb/isp1760/Kconfig create mode 100644 drivers/usb/isp1760/Makefile create mode 100644 drivers/usb/isp1760/isp1760-core.c create mode 100644 drivers/usb/isp1760/isp1760-core.h create mode 100644 drivers/usb/isp1760/isp1760-hcd.c create mode 100644 drivers/usb/isp1760/isp1760-hcd.h create mode 100644 drivers/usb/isp1760/isp1760-if.c create mode 100644 drivers/usb/isp1760/isp1760-regs.h create mode 100644 drivers/usb/isp1760/isp1760-uboot.c create mode 100644 drivers/usb/isp1760/isp1760-uboot.h rename drivers/usb/musb-new/usb-compat.h => include/linux/usb/usb_urb_compat.h (59%) -- 2.36.1

2 7