March 2022 - U-Boot

[PATCH] ARM: mach-omap2: omap3: Make clock functions static
by Adam Ford 14 Mar '22

14 Mar '22

get_osc_clk_speed and get_sys_clkin_sel are only used in one file. Make them static. Tested on OMAP3530, DM3730, AM3517. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/mach-omap2/omap3/clock.c b/arch/arm/mach-omap2/omap3/clock.c index 71f73492c6..13685e0567 100644 --- a/arch/arm/mach-omap2/omap3/clock.c +++ b/arch/arm/mach-omap2/omap3/clock.c @@ -23,7 +23,7 @@ * get_sys_clk_speed() - determine reference oscillator speed * based on known 32kHz clock and gptimer. *****************************************************************************/ -u32 get_osc_clk_speed(void) +static u32 get_osc_clk_speed(void) { u32 start, cstart, cend, cdiff, cdiv, val; struct prcm *prcm_base = (struct prcm *)PRCM_BASE; @@ -90,7 +90,7 @@ u32 get_osc_clk_speed(void) * get_sys_clkin_sel() - returns the sys_clkin_sel field value based on * input oscillator clock frequency. *****************************************************************************/ -void get_sys_clkin_sel(u32 osc_clk, u32 *sys_clkin_sel) +static void get_sys_clkin_sel(u32 osc_clk, u32 *sys_clkin_sel) { switch(osc_clk) { case S38_4M: -- 2.34.1

2 1

[PATCH v<9>] arm: add initial support for the Phytium Pomelo Board
by nicholas_zheng＠outlook.com 14 Mar '22

14 Mar '22

From: weichangzheng <nicholas_zheng(a)outlook.com> This adds platform code and the device tree for the Phytium Pomelo Board. The initial support comprises the UART and the PCIE. Signed-off-by: weichangzheng <nicholas_zheng(a)outlook.com> Changes since v1: updated to DT Changes since v2: Modify some explicit types and macro Changes since v3: Modify some SDRAM related macro definitions and distro_bootcmd Changes since v4: Modify distro_bootcmd Changes since v5: Modify the CPU node description of the DT Changes since v6: Modify DT Changes since v7: Modify DT Changes since v8: Temporarily remove the CPU node description of the DT --- arch/arm/Kconfig | 20 ++++ arch/arm/dts/Makefile | 1 + arch/arm/dts/phytium-pomelo.dts | 50 ++++++++++ board/phytium/pomelo/Kconfig | 12 +++ board/phytium/pomelo/MAINTAINERS | 8 ++ board/phytium/pomelo/Makefile | 14 +++ board/phytium/pomelo/cpu.h | 73 ++++++++++++++ board/phytium/pomelo/ddr.c | 161 +++++++++++++++++++++++++++++++ board/phytium/pomelo/pcie.c | 60 ++++++++++++ board/phytium/pomelo/pll.c | 73 ++++++++++++++ board/phytium/pomelo/pomelo.c | 118 ++++++++++++++++++++++ board/phytium/pomelo/sec.c | 37 +++++++ configs/pomelo_defconfig | 18 ++++ include/configs/pomelo.h | 44 +++++++++ 14 files changed, 689 insertions(+) create mode 100644 arch/arm/dts/phytium-pomelo.dts create mode 100644 board/phytium/pomelo/Kconfig create mode 100644 board/phytium/pomelo/MAINTAINERS create mode 100644 board/phytium/pomelo/Makefile create mode 100644 board/phytium/pomelo/cpu.h create mode 100644 board/phytium/pomelo/ddr.c create mode 100644 board/phytium/pomelo/pcie.c create mode 100644 board/phytium/pomelo/pll.c create mode 100644 board/phytium/pomelo/pomelo.c create mode 100644 board/phytium/pomelo/sec.c create mode 100644 configs/pomelo_defconfig create mode 100644 include/configs/pomelo.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 0448787b8b..029af85fcb 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1818,6 +1818,25 @@ config TARGET_DURIAN Support for durian platform. It has 2GB Sdram, uart and pcie. +config TARGET_POMELO + bool "Support Phytium Pomelo Platform" + select ARM64 + select DM + select AHCI + select SCSI_AHCI + select AHCI_PCI + select BLK + select PCI + select DM_PCI + select SCSI + select DM_SCSI + select DM_SERIAL + select DM_ETH if NET + imply CMD_PCI + help + Support for pomelo platform. + It has 8GB Sdram, uart and pcie. + config TARGET_PRESIDIO_ASIC bool "Support Cortina Presidio ASIC Platform" select ARM64 @@ -2038,6 +2057,7 @@ source "board/toradex/colibri_pxa270/Kconfig" source "board/variscite/dart_6ul/Kconfig" source "board/vscom/baltos/Kconfig" source "board/phytium/durian/Kconfig" +source "board/phytium/pomelo/Kconfig" source "board/xen/xenguest_arm64/Kconfig" source "board/keymile/Kconfig" diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 9fb38682e6..45d0340bd3 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1107,6 +1107,7 @@ dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb dtb-$(CONFIG_TARGET_TOTAL_COMPUTE) += total_compute.dtb dtb-$(CONFIG_TARGET_DURIAN) += phytium-durian.dtb +dtb-$(CONFIG_TARGET_POMELO) += phytium-pomelo.dtb dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb diff --git a/arch/arm/dts/phytium-pomelo.dts b/arch/arm/dts/phytium-pomelo.dts new file mode 100644 index 0000000000..3f809c0dbb --- /dev/null +++ b/arch/arm/dts/phytium-pomelo.dts @@ -0,0 +1,50 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * dts file for Phytium Pomelo board + * Copyright (C) 2021, Phytium Ltd. + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ +/dts-v1/; + +/ { + model = "Phytium Pomelo Board"; + compatible = "phytium,d2000-pomelo", "phytium,d2000"; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &uart0; + }; + + sysclk_48mhz: clk48mhz { + compatible = "fixed-clock"; + #clock-cells = <0x0>; + clock-frequency = <48000000>; + clock-output-names = "sysclk_48mhz"; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + uart0: serial@28001000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0x28001000 0x0 0x1000>; + clocks = <&sysclk_48mhz>; + }; + + pcie@40000000 { + compatible = "pci-host-ecam-generic"; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + reg = <0x0 0x40000000 0x0 0x10000000>; + ranges = <0x01000000 0x00 0x00000000 0x0 0x50000000 0x0 0x00F00000>, + <0x02000000 0x00 0x58000000 0x0 0x58000000 0x0 0x28000000>, + <0x43000000 0x10 0x00000000 0x10 0x00000000 0x10 0x00000000>; + }; + }; +}; diff --git a/board/phytium/pomelo/Kconfig b/board/phytium/pomelo/Kconfig new file mode 100644 index 0000000000..281aa8feff --- /dev/null +++ b/board/phytium/pomelo/Kconfig @@ -0,0 +1,12 @@ +if TARGET_POMELO + +config SYS_BOARD + default "pomelo" + +config SYS_VENDOR + default "phytium" + +config SYS_CONFIG_NAME + default "pomelo" + +endif diff --git a/board/phytium/pomelo/MAINTAINERS b/board/phytium/pomelo/MAINTAINERS new file mode 100644 index 0000000000..d76a4a026e --- /dev/null +++ b/board/phytium/pomelo/MAINTAINERS @@ -0,0 +1,8 @@ +POMELO BOARD +M: lixinde <lixinde(a)phytium.com.cn> +M: weichangzheng <weichangzheng(a)phytium.com.cn> +S: Maintained +F: board/phytium/pomelo/* +F: include/configs/pomelo.h +F: configs/pomelo_defconfig +F: arch/arm/dts/phytium-pomelo.dts diff --git a/board/phytium/pomelo/Makefile b/board/phytium/pomelo/Makefile new file mode 100644 index 0000000000..b9cb3609bd --- /dev/null +++ b/board/phytium/pomelo/Makefile @@ -0,0 +1,14 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2021 +# lixinde <lixinde(a)phytium.com.cn> +# weichangzheng <weichangzheng(a)phytium.com.cn> +# + +obj-y += pomelo.o +obj-y += pll.o +obj-y += pcie.o +obj-y += ddr.o +obj-y += sec.o + + diff --git a/board/phytium/pomelo/cpu.h b/board/phytium/pomelo/cpu.h new file mode 100644 index 0000000000..005ea5982b --- /dev/null +++ b/board/phytium/pomelo/cpu.h @@ -0,0 +1,73 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2021 + * Phytium Technology Ltd <www.phytium.com> + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#ifndef _FT_POMELO_H +#define _FT_POMELO_H + +/* SMCCC ID */ +#define CPU_SVC_VERSION 0xC2000F00 +#define CPU_GET_RST_SOURCE 0xC2000F01 +#define CPU_INIT_PLL 0xC2000F02 +#define CPU_INIT_PCIE 0xC2000F03 +#define CPU_INIT_MEM 0xC2000F04 +#define CPU_INIT_SEC_SVC 0xC2000F05 + +/*CPU RESET*/ +#define CPU_RESET_POWER_ON 0x1 +#define CPU_RESET_PLL 0x4 +#define CPU_RESET_WATCH_DOG 0x8 + +/* PLL */ +#define PARAMETER_PLL_MAGIC 0x54460010 + +/* PCIE */ +#define PARAMETER_PCIE_MAGIC 0x54460011 +#define CFG_INDEPENDENT_TREE 0x0 +#define PCI_PEU0 0x1 +#define PCI_PEU1 0x1 +#define PEU1_OFFSET 16 +#define PEU_C_OFFSET_MODE 16 +#define PEU_C_OFFSET_SPEED 0 +#define RC_MODE 0x1 +#define X8X8 0x1 +#define GEN3 3 + +/* DDR */ +#define PARAMETER_MCU_MAGIC 0x54460014 +#define PARAM_MCU_VERSION 0x1 +#define PARAM_MCU_SIZE 0x100 +#define PARAM_CH_ENABLE 0x3 +#define PARAM_ECC_ENABLE 0x3 +#define PARAM_FORCE_SPD_DISABLE 0x0 +#define PARAM_MCU_MISC_ENABLE 0x0 + +#define UDIMM_TYPE 0x2 +#define DIMM_X8 0x1 +#define NO_MIRROR 0x0 +#define NO_ECC_TYPE 0 +#define DDR4_TYPE 0xC + +/* SEC */ +#define PARAMETER_COMMON_MAGIC 0x54460013 + +/* FLUSH L3 CASHE */ +#define HNF_COUNT 0x8 +#define HNF_PSTATE_REQ (HNF_BASE + 0x10) +#define HNF_PSTATE_STAT (HNF_BASE + 0x18) +#define HNF_PSTATE_OFF 0x0 +#define HNF_PSTATE_SFONLY 0x1 +#define HNF_PSTATE_HALF 0x2 +#define HNF_PSTATE_FULL 0x3 +#define HNF_STRIDE 0x10000 +#define HNF_BASE (unsigned long)(0x3A200000) +void ddr_init(void); +void sec_init(void); +void check_reset(void); +void pcie_init(void); + +#endif /* _FT_POMELO_H */ diff --git a/board/phytium/pomelo/ddr.c b/board/phytium/pomelo/ddr.c new file mode 100644 index 0000000000..c6dbed9639 --- /dev/null +++ b/board/phytium/pomelo/ddr.c @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#include <stdio.h> +#include <linux/arm-smccc.h> +#include <init.h> +#include "cpu.h" + +struct ddr_spd { + /******************* read from spd *****************/ + u8 dimm_type; /* 1: RDIMM;2: UDIMM;3: SODIMM;4: LRDIMM */ + u8 data_width; /* 0: x4; 1: x8; 2: x16 */ + u8 mirror_type;/* 0: stardard; 1: mirror */ + u8 ecc_type; /* 0: no-ecc; 1:ecc */ + u8 dram_type; /* 0xB: DDR3; 0xC: DDR4 */ + u8 rank_num; + u8 row_num; + u8 col_num; + + u8 bg_num; /*only DDR4*/ + u8 bank_num; + u16 module_manufacturer_id; + u16 taamin; + u16 trcdmin; + + u16 trpmin; + u16 trasmin; + u16 trcmin; + u16 tfawmin; + + u16 trrd_smin; /*only DDR4*/ + u16 trrd_lmin; /*only DDR4*/ + u16 tccd_lmin; /*only DDR4*/ + u16 twrmin; + + u16 twtr_smin; /*only DDR4*/ + u16 twtr_lmin; /*only DDR4*/ + u16 twtrmin; /*only DDR3*/ + u16 trrdmin; /*only DDR3*/ + + /******************* RCD control words *****************/ + u8 f0rc03; /*bit[3:2]:CS bit[1:0]:CA */ + u8 f0rc04; /*bit[3:2]:ODT bit[1:0]:CKE */ + u8 f0rc05; /*bit[3:2]:CLK-A side bit[1:0]:CLK-B side */ + u8 bc00; + u8 bc01; + u8 bc02; + u8 bc03; + u8 bc04; + + u8 bc05; + u8 f5bc5x; + u8 f5bc6x; + /******************* LRDIMM special *****************/ + u8 vrefdq_pr0; + u8 vrefdq_mdram; + u8 rtt_mdram_1866; + u8 rtt_mdram_2400; + u8 rtt_mdram_3200; + + u8 drive_dram; + u8 odt_dram_1866; + u8 odt_dram_2400; + u8 odt_dram_3200; + u8 park_dram_1866; + u8 park_dram_2400; + u8 park_dram_3200; + u8 rcd_num; +} __attribute((aligned(4))); + +struct mcu_config { + u32 magic; + u32 version; + u32 size; + u8 rev1[4]; + + u8 ch_enable; + u8 misc1_enable; + u8 misc2_enable; + u8 force_spd_enable; + u8 misc3_enable; + u8 train_debug; + u8 train_recover; + u8 rev2[9]; + + struct ddr_spd ddr_spd_info[2]; +} __attribute((aligned(4))); + +static void get_mcu_up_info_default(struct mcu_config *pm) +{ + pm->magic = PARAMETER_MCU_MAGIC; + pm->version = PARAM_MCU_VERSION; + pm->size = PARAM_MCU_SIZE; + pm->ch_enable = PARAM_CH_ENABLE; + pm->misc1_enable = PARAM_ECC_ENABLE; + pm->force_spd_enable = PARAM_FORCE_SPD_DISABLE; + pm->misc3_enable = PARAM_MCU_MISC_ENABLE; + pm->train_recover = 0x0; +} + +static u8 init_dimm_param(u8 ch, struct mcu_config *pm) +{ + debug("manual config dimm info...\n"); + pm->ddr_spd_info[ch].dimm_type = UDIMM_TYPE; + pm->ddr_spd_info[ch].data_width = DIMM_X8; + pm->ddr_spd_info[ch].mirror_type = NO_MIRROR; + pm->ddr_spd_info[ch].ecc_type = NO_ECC_TYPE; + pm->ddr_spd_info[ch].dram_type = DDR4_TYPE; + pm->ddr_spd_info[ch].rank_num = 1; + pm->ddr_spd_info[ch].row_num = 16; + pm->ddr_spd_info[ch].col_num = 10; + pm->ddr_spd_info[ch].bg_num = 4; + pm->ddr_spd_info[ch].bank_num = 4; + pm->ddr_spd_info[ch].taamin = 13750; + pm->ddr_spd_info[ch].trcdmin = 13750; + + pm->ddr_spd_info[ch].trpmin = 13750; + pm->ddr_spd_info[ch].trasmin = 32000; + pm->ddr_spd_info[ch].trcmin = 45750; + pm->ddr_spd_info[ch].tfawmin = 21000; + + pm->ddr_spd_info[ch].trrd_smin = 3000; + pm->ddr_spd_info[ch].trrd_lmin = 4900; + pm->ddr_spd_info[ch].tccd_lmin = 5000; + pm->ddr_spd_info[ch].twrmin = 15000; + + pm->ddr_spd_info[ch].twtr_smin = 2500; + pm->ddr_spd_info[ch].twtr_lmin = 7500; + + return 0; +} + +void get_default_mcu_info(u8 *data) +{ + get_mcu_up_info_default((struct mcu_config *)data); +} + +void fix_mcu_info(u8 *data) +{ + struct mcu_config *mcu_info = (struct mcu_config *)data; + + for (int ch = 0; ch < 2; ch++) + init_dimm_param(ch, mcu_info); +} + +void ddr_init(void) +{ + u8 buffer[0x100]; + struct arm_smccc_res res; + + get_default_mcu_info(buffer); + fix_mcu_info(buffer); + + arm_smccc_smc(CPU_INIT_MEM, 0, (u64)buffer, 0, 0, 0, 0, 0, &res); + if (res.a0 != 0) + panic("DRAM init failed :0x%lx\n", res.a0); +} diff --git a/board/phytium/pomelo/pcie.c b/board/phytium/pomelo/pcie.c new file mode 100644 index 0000000000..698d82fd8d --- /dev/null +++ b/board/phytium/pomelo/pcie.c @@ -0,0 +1,60 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#include <stdio.h> +#include <string.h> +#include <linux/arm-smccc.h> +#include <init.h> +#include "cpu.h" + +struct pcu_ctr { + u32 base_config[3]; + u32 equalization[3]; + u8 rev[80]; +} __attribute((aligned(4))); + +struct pcu_config { + u32 magic; + u32 version; + u32 size; + u8 rev1[4]; + u32 independent_tree; + u32 base_cfg; + u8 rev2[16]; + struct pcu_ctr ctr_cfg[2]; +} __attribute((aligned(4))); + +struct pcu_config const peu_base_info = { + .magic = PARAMETER_PCIE_MAGIC, + .version = 0x2, + .size = 0x100, + .independent_tree = CFG_INDEPENDENT_TREE, + .base_cfg = ((PCI_PEU1 | (X8X8 << 1)) << PEU1_OFFSET | (PCI_PEU0 | (X8X8 << 1))), + .ctr_cfg[0].base_config[0] = (RC_MODE << PEU_C_OFFSET_MODE) | (GEN3 << PEU_C_OFFSET_SPEED), + .ctr_cfg[0].base_config[1] = (RC_MODE << PEU_C_OFFSET_MODE) | (GEN3 << PEU_C_OFFSET_SPEED), + .ctr_cfg[0].base_config[2] = (RC_MODE << PEU_C_OFFSET_MODE) | (GEN3 << PEU_C_OFFSET_SPEED), + .ctr_cfg[1].base_config[0] = (RC_MODE << PEU_C_OFFSET_MODE) | (GEN3 << PEU_C_OFFSET_SPEED), + .ctr_cfg[1].base_config[1] = (RC_MODE << PEU_C_OFFSET_MODE) | (GEN3 << PEU_C_OFFSET_SPEED), + .ctr_cfg[1].base_config[2] = (RC_MODE << PEU_C_OFFSET_MODE) | (GEN3 << PEU_C_OFFSET_SPEED), + .ctr_cfg[0].equalization[0] = 0x7, + .ctr_cfg[0].equalization[1] = 0x7, + .ctr_cfg[0].equalization[2] = 0x7, + .ctr_cfg[1].equalization[0] = 0x7, + .ctr_cfg[1].equalization[1] = 0x7, + .ctr_cfg[1].equalization[2] = 0x7, +}; + +void pcie_init(void) +{ + u8 buffer[0x100]; + struct arm_smccc_res res; + + memcpy(buffer, &peu_base_info, sizeof(peu_base_info)); + arm_smccc_smc(CPU_INIT_PCIE, 0, (u64)buffer, 0, 0, 0, 0, 0, &res); + if (res.a0 != 0) + panic("PCIE init failed :0x%lx\n", res.a0); +} diff --git a/board/phytium/pomelo/pll.c b/board/phytium/pomelo/pll.c new file mode 100644 index 0000000000..a66ffddf09 --- /dev/null +++ b/board/phytium/pomelo/pll.c @@ -0,0 +1,73 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#include <stdio.h> +#include <string.h> +#include <asm/io.h> +#include <linux/arm-smccc.h> +#include <init.h> +#include "cpu.h" + +struct pll_config { + u32 magic; + u32 version; + u32 size; + u8 rev1[4]; + u32 core_pll; + u32 res1; + u32 lmu_pll; + u32 res2; + u32 res3; + u32 res4; + u32 res5; +} __attribute((aligned(4))); + +struct pll_config const pll_base_info = { + .magic = PARAMETER_PLL_MAGIC, + .version = 0x1, + .size = 0x30, + .core_pll = 2300, /*MHz*/ + .lmu_pll = 667, /*MHz*/ +}; + +u32 get_reset_source(void) +{ + struct arm_smccc_res res; + + arm_smccc_smc(CPU_GET_RST_SOURCE, 0, 0, 0, 0, 0, 0, 0, &res); + return res.a0; +} + +void pll_init(void) +{ + u8 buffer[0x100]; + struct arm_smccc_res res; + + memcpy(buffer, &pll_base_info, sizeof(pll_base_info)); + arm_smccc_smc(CPU_INIT_PLL, 0, (u64)buffer, 0, 0, 0, 0, 0, &res); + if (res.a0 != 0) + panic("PLL init failed :0x%lx\n", res.a0); +} + +void check_reset(void) +{ + u32 rst; + + rst = get_reset_source(); + + switch (rst) { + case CPU_RESET_POWER_ON: + pll_init(); + break; + case CPU_RESET_PLL: + break; + case CPU_RESET_WATCH_DOG: + break; + default: + panic("other reset source\n"); + } +} diff --git a/board/phytium/pomelo/pomelo.c b/board/phytium/pomelo/pomelo.c new file mode 100644 index 0000000000..4fbe1e5835 --- /dev/null +++ b/board/phytium/pomelo/pomelo.c @@ -0,0 +1,118 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#include <stdio.h> +#include <command.h> +#include <init.h> +#include <asm/armv8/mmu.h> +#include <asm/io.h> +#include <linux/arm-smccc.h> +#include <scsi.h> +#include <init.h> +#include <asm/u-boot.h> +#include "cpu.h" + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + debug("Phytium ddr init\n"); + ddr_init(); + + gd->mem_clk = 0; + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, 0x7b000000); + + sec_init(); + debug("PBF relocate done\n"); + + return 0; +} + +int board_init(void) +{ + return 0; +} + +void reset_cpu(void) +{ + struct arm_smccc_res res; + + debug("run in reset cpu\n"); + arm_smccc_smc(0x84000009, 0, 0, 0, 0, 0, 0, 0, &res); + if (res.a0 != 0) + panic("reset cpu error, %lx\n", res.a0); +} + +int mach_cpu_init(void) +{ + check_reset(); + return 0; +} + +int board_early_init_f(void) +{ + pcie_init(); + return 0; +} + +static struct mm_region pomelo_mem_map[] = { + { + .virt = 0x0UL, + .phys = 0x0UL, + .size = 0x80000000UL, + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | + PTE_BLOCK_NON_SHARE | + PTE_BLOCK_PXN | + PTE_BLOCK_UXN + }, + { + .virt = 0x80000000UL, + .phys = 0x80000000UL, + .size = 0x7b000000UL, + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | + PTE_BLOCK_NS | + PTE_BLOCK_INNER_SHARE + }, + { + 0, + } +}; + +struct mm_region *mem_map = pomelo_mem_map; + +int __asm_flush_l3_dcache(void) +{ + int i, pstate; + + for (i = 0; i < HNF_COUNT; i++) + writeq(HNF_PSTATE_SFONLY, HNF_PSTATE_REQ + i * HNF_STRIDE); + for (i = 0; i < HNF_COUNT; i++) { + do { + pstate = readq(HNF_PSTATE_STAT + i * HNF_STRIDE); + } while ((pstate & 0xf) != (HNF_PSTATE_SFONLY << 2)); + } + + for (i = 0; i < HNF_COUNT; i++) + writeq(HNF_PSTATE_FULL, HNF_PSTATE_REQ + i * HNF_STRIDE); + + return 0; +} + +int last_stage_init(void) +{ + int ret; + + /* pci e */ + pci_init(); + /* scsi scan */ + ret = scsi_scan(true); + if (ret) { + printf("scsi scan failed\n"); + return CMD_RET_FAILURE; + } + return ret; +} diff --git a/board/phytium/pomelo/sec.c b/board/phytium/pomelo/sec.c new file mode 100644 index 0000000000..aeb3983f01 --- /dev/null +++ b/board/phytium/pomelo/sec.c @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#include <stdio.h> +#include <string.h> +#include <linux/arm-smccc.h> +#include <init.h> +#include "cpu.h" + +struct common_config { + u32 magic; + u32 version; + u32 size; + u8 rev1[4]; + u64 core_bit_map; +} __attribute((aligned(4))); + +struct common_config const common_base_info = { + .magic = PARAMETER_COMMON_MAGIC, + .version = 0x1, + .core_bit_map = 0x3333, +}; + +void sec_init(void) +{ + u8 buffer[0x100]; + struct arm_smccc_res res; + + memcpy(buffer, &common_base_info, sizeof(common_base_info)); + arm_smccc_smc(CPU_INIT_SEC_SVC, 0, (u64)buffer, 0, 0, 0, 0, 0, &res); + if (res.a0 != 0) + panic("SEC init failed :0x%lx\n", res.a0); +} diff --git a/configs/pomelo_defconfig b/configs/pomelo_defconfig new file mode 100644 index 0000000000..a963d85fbb --- /dev/null +++ b/configs/pomelo_defconfig @@ -0,0 +1,18 @@ +CONFIG_ARM=y +CONFIG_ARM_SMCCC=y +CONFIG_TARGET_POMELO=y +CONFIG_SYS_TEXT_BASE=0x180000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_DEFAULT_DEVICE_TREE="phytium-pomelo" +CONFIG_DISTRO_DEFAULTS=y +CONFIG_USE_BOOTARGS=y +CONFIG_BOOTARGS="console=ttyAMA0,115200 earlycon=pl011,0x28001000 root=/dev/sda2 rw" +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_LAST_STAGE_INIT=y +CONFIG_SYS_PROMPT="pomelo#" +CONFIG_OF_CONTROL=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_DM_PCI_COMPAT=y +CONFIG_PCI_PHYTIUM=y +CONFIG_PCIE_ECAM_GENERIC=y +CONFIG_PL01X_SERIAL=y diff --git a/include/configs/pomelo.h b/include/configs/pomelo.h new file mode 100644 index 0000000000..d9fc03ada7 --- /dev/null +++ b/include/configs/pomelo.h @@ -0,0 +1,44 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2021 + * lixinde <lixinde(a)phytium.com.cn> + * weichangzheng <weichangzheng(a)phytium.com.cn> + */ + +#ifndef __POMELO_CONFIG_H__ +#define __POMELO_CONFIG_H__ + +/* SDRAM Bank #1 start address */ +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_LOAD_ADDR (0x80000000 + 0x10000000) + +/* SIZE of malloc pool */ +#define CONFIG_SYS_MALLOC_LEN (0x100000 + 0x1000) +#define CONFIG_SYS_INIT_SP_ADDR (0x29800000 + 0x1a000) + +/* PCI CONFIG */ +#define CONFIG_SYS_PCI_64BIT 1 + +/*BOOT*/ +#define CONFIG_SYS_BOOTM_LEN 0x3c00000 +#define CONFIG_BOARD_EARLY_INIT_F + +#ifndef CONFIG_SPL_BUILD +#define BOOT_TARGET_DEVICES(func) \ + func(SCSI, scsi, 0) \ + +#include <config_distro_bootcmd.h> +#endif + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "image=Image\0" \ + BOOTENV \ + "scriptaddr=0x90100000\0" \ + "kernel_addr_r=0x90200000\0" \ + "fdt_addr_r=0x95000000\0" \ + "boot_fit=no\0" \ + "fdtfile=phytium-pomelo.dtb\0" \ + +#endif + -- 2.17.1

2 1

[PATCH 1/2] ARM: dts: am3517-evm: Sync DTS with Linux 5.17-rc5
by Adam Ford 14 Mar '22

14 Mar '22

Sync the am3517-evm device tree files with those from Linux 5.17-rc5 with some additional fixes for pinmuxing Ethernet and moving the pinmux references to the respective peripherals. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/am3517-evm-u-boot.dtsi b/arch/arm/dts/am3517-evm-u-boot.dtsi index d5a4ce97d1..1a70630322 100644 --- a/arch/arm/dts/am3517-evm-u-boot.dtsi +++ b/arch/arm/dts/am3517-evm-u-boot.dtsi @@ -37,7 +37,18 @@ /delete-property/ u-boot,dm-spl; }; -/delete-node/ &uart1; -/delete-node/ &uart2; -/delete-node/ &mmc2; -/delete-node/ &mmc3; +&mmc2 { + /delete-property/ u-boot,dm-spl; +}; + +&mmc3 { + /delete-property/ u-boot,dm-spl; +}; + +&uart1 { + /delete-property/ u-boot,dm-spl; +}; + +&uart2 { + /delete-property/ u-boot,dm-spl; +}; diff --git a/arch/arm/dts/am3517-evm-ui.dtsi b/arch/arm/dts/am3517-evm-ui.dtsi index 54aa2522aa..7d8f32bf70 100644 --- a/arch/arm/dts/am3517-evm-ui.dtsi +++ b/arch/arm/dts/am3517-evm-ui.dtsi @@ -1,9 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* - * Copyright (C) 2018 Logic PD, Inc - http://www.logicpd.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. + * Copyright (C) 2018 Logic PD, Inc - https://www.logicpd.com/ */ #include <dt-bindings/input/input.h> diff --git a/arch/arm/dts/am3517-evm.dts b/arch/arm/dts/am3517-evm.dts index 935c471c97..a01f9cf047 100644 --- a/arch/arm/dts/am3517-evm.dts +++ b/arch/arm/dts/am3517-evm.dts @@ -1,9 +1,6 @@ +// SPDX-License-Identifier: GPL-2.0-only /* - * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. + * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/ */ /dts-v1/; @@ -127,10 +124,11 @@ }; lcd0: display@0 { - compatible = "panel-dpi"; + /* This isn't the exact LCD, but the timings meet spec */ + /* To make it work, set CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 */ + compatible = "newhaven,nhd-4.3-480272ef-atxl"; label = "15"; - status = "okay"; - pinctrl-names = "default"; + backlight = <&bl>; enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* gpio176, lcd INI */ vcc-supply = <&vdd_io_reg>; @@ -139,22 +137,6 @@ remote-endpoint = <&dpi_out>; }; }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <4>; - vsync-len = <11>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <1>; - }; }; bl: backlight { @@ -174,10 +156,13 @@ pinctrl-0 = <&pwm_pins>; ti,timers = <&timer11>; #pwm-cells = <3>; + ti,clock-source = <0x01>; }; /* HS USB Host PHY on PORT 1 */ hsusb1_phy: hsusb1_phy { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1_rst_pins>; compatible = "usb-nop-xceiv"; reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; /* gpio_57 */ #phy-cells = <0>; @@ -185,7 +170,9 @@ }; &davinci_emac { - status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ethernet_pins>; + status = "okay"; }; &davinci_mdio { @@ -240,6 +227,8 @@ }; &usbhshost { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1_pins>; port1-mode = "ehci-phy"; }; @@ -248,8 +237,21 @@ }; &omap3_pmx_core { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb1_rst_pins>; + + ethernet_pins: pinmux_ethernet_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21fe, PIN_INPUT | MUX_MODE0) /* rmii_mdio_data */ + OMAP3_CORE1_IOPAD(0x2200, MUX_MODE0) /* rmii_mdio_clk */ + OMAP3_CORE1_IOPAD(0x2202, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd0 */ + OMAP3_CORE1_IOPAD(0x2204, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd1 */ + OMAP3_CORE1_IOPAD(0x2206, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_crs_dv */ + OMAP3_CORE1_IOPAD(0x2208, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_rxer */ + OMAP3_CORE1_IOPAD(0x220a, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd0 */ + OMAP3_CORE1_IOPAD(0x220c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd1 */ + OMAP3_CORE1_IOPAD(0x220e, PIN_OUTPUT_PULLDOWN |MUX_MODE0) /* rmii_txen */ + OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */ + >; + }; leds_pins: pinmux_leds_pins { pinctrl-single,pins = < @@ -317,8 +319,6 @@ }; &omap3_pmx_core2 { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb1_pins>; hsusb1_pins: pinmux_hsusb1_pins { pinctrl-single,pins = < diff --git a/arch/arm/dts/am3517-som.dtsi b/arch/arm/dts/am3517-som.dtsi index b1c988eed8..8b669e2eaf 100644 --- a/arch/arm/dts/am3517-som.dtsi +++ b/arch/arm/dts/am3517-som.dtsi @@ -1,11 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * Copyright (C) 2016 Derald D. Woods <woods.technical(a)gmail.com> * * Based on am3517-evm.dts - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. */ / { -- 2.34.1

3 5

[PATCH] ARM: dts: logicpd-torpedo: Resyc DTS files with Linux 5.17-rc5
by Adam Ford 14 Mar '22

14 Mar '22

Resyc DTS files with Linux 5.17-rc5. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts index 7675bc3fa8..cb08aa62d9 100644 --- a/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts +++ b/arch/arm/dts/logicpd-torpedo-35xx-devkit.dts @@ -9,5 +9,13 @@ / { model = "LogicPD Zoom OMAP35xx Torpedo Development Kit"; - compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core { + isp1763_pins: pinmux_isp1763_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE4) /* sdmmc1_dat6.gpio_128 */ + >; + }; }; diff --git a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts index 18c27e8505..07ea822fe4 100644 --- a/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts +++ b/arch/arm/dts/logicpd-torpedo-37xx-devkit.dts @@ -50,6 +50,20 @@ }; }; +&uart2 { + /delete-property/dma-names; + bluetooth { + compatible = "ti,wl1283-st"; + enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */ + max-speed = <3000000>; + }; +}; + +/* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */ +&mt9p031_out { + pixel-clock-frequency = <90000000>; +}; + &omap3_pmx_core { mmc3_pins: pinmux_mm3_pins { pinctrl-single,pins = < @@ -71,3 +85,12 @@ >; }; }; + +/* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */ +&omap3_pmx_wkup { + isp1763_pins: pinmux_isp1763_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4) /* reserved.gpio_128 */ + >; + }; +}; diff --git a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi index 642e809e75..b4664ab002 100644 --- a/arch/arm/dts/logicpd-torpedo-baseboard.dtsi +++ b/arch/arm/dts/logicpd-torpedo-baseboard.dtsi @@ -65,6 +65,7 @@ pinctrl-0 = <&pwm_pins>; ti,timers = <&timer10>; #pwm-cells = <3>; + ti,clock-source = <0x01>; }; }; @@ -80,6 +81,8 @@ }; &mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; status = "okay"; }; @@ -90,7 +93,8 @@ &gpmc { ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */ - 1 0 0x2c000000 0x1000000>; /* CS1: 16MB for LAN9221 */ + 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */ + 6 0 0x28000000 0x1000000>; /* CS6: 16MB for ISP1763 */ ethernet@gpmc { pinctrl-names = "default"; @@ -99,16 +103,60 @@ interrupts = <1 IRQ_TYPE_LEVEL_LOW>; /* gpio129 */ reg = <1 0 0xff>; }; + + usb@6,0 { + pinctrl-names = "default"; + pinctrl-0 = <&isp1763_pins>; + compatible = "nxp,usb-isp1763"; + reg = <0x6 0x0 0xff>; + interrupt-parent = <&gpio5>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host"; + bus-width = <16>; + dr_mode = "host"; + gpmc,mux-add-data = <0>; + gpmc,device-width = <2>; + gpmc,wait-pin = <0>; + gpmc,burst-length = <4>; + gpmc,cycle2cycle-samecsen = <1>; + gpmc,cycle2cycle-diffcsen = <1>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <45>; + gpmc,cs-wr-off-ns = <45>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <0>; + gpmc,adv-wr-off-ns = <0>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <45>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <25>; + gpmc,rd-cycle-ns = <60>; + gpmc,wr-cycle-ns = <45>; + gpmc,access-ns = <35>; + gpmc,page-burst-access-ns = <0>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <60>; + gpmc,wait-monitoring-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wr-data-mux-bus-ns = <5>; + gpmc,wr-access-ns = <20>; + }; }; +&hdqw1w { + pinctrl-names = "default"; + pinctrl-0 = <&hdq_pins>; +}; + + &vpll2 { regulator-always-on; }; &dss { - status = "ok"; + status = "okay"; vdds_dsi-supply = <&vpll2>; - vdda_video-supply = <&video_reg>; + vdda_video-supply = <&vpll2>; pinctrl-names = "default"; pinctrl-0 = <&dss_dpi_pins1>; port { @@ -124,44 +172,19 @@ display0 = &lcd0; }; - video_reg: video_reg { - pinctrl-names = "default"; - pinctrl-0 = <&panel_pwr_pins>; - compatible = "regulator-fixed"; - regulator-name = "fixed-supply"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ - }; - lcd0: display { - compatible = "panel-dpi"; + /* This isn't the exact LCD, but the timings meet spec */ + compatible = "newhaven,nhd-4.3-480272ef-atxl"; label = "15"; - status = "okay"; - /* default-on; */ pinctrl-names = "default"; - + pinctrl-0 = <&panel_pwr_pins>; + backlight = <&bl>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; port { lcd_in: endpoint { remote-endpoint = <&dpi_out>; }; }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <4>; - vsync-len = <11>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <1>; - }; }; bl: backlight { @@ -193,6 +216,12 @@ >; }; + hdq_pins: hdq_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0) /* hdq_sio */ + >; + }; + pwm_pins: pinmux_pwm_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */ diff --git a/arch/arm/dts/logicpd-torpedo-som.dtsi b/arch/arm/dts/logicpd-torpedo-som.dtsi index 3fdd0a72f8..3a5228562b 100644 --- a/arch/arm/dts/logicpd-torpedo-som.dtsi +++ b/arch/arm/dts/logicpd-torpedo-som.dtsi @@ -35,6 +35,11 @@ }; }; +/* The Torpedo doesn't route the USB host pins */ +&usbhshost { + status = "disabled"; +}; + &gpmc { ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ @@ -192,3 +197,7 @@ &twl_gpio { ti,use-leds; }; + +&twl_keypad { + status = "disabled"; +}; -- 2.34.1

2 1

[PATCH 1/2] ARM: dts: logicpd-som-lv: Resync DTS files with Linux 5.17-rc5
by Adam Ford 14 Mar '22

14 Mar '22

Resync the DTS files for the Logic PD SOM-LV with Linux 5.17-rc5 with some additional pending changes to address issues with wrong pin-muxing on the OMAP35. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts index f7a841a288..f690bc83bf 100644 --- a/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts +++ b/arch/arm/dts/logicpd-som-lv-35xx-devkit.dts @@ -9,5 +9,19 @@ / { model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit"; - compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3"; + compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core2 { + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; }; diff --git a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts index a604d92221..e28e9625be 100644 --- a/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts +++ b/arch/arm/dts/logicpd-som-lv-37xx-devkit.dts @@ -11,3 +11,17 @@ model = "LogicPD Zoom DM3730 SOM-LV Development Kit"; compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3"; }; + +&omap3_pmx_core2 { + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; +}; diff --git a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi index 100396f6c2..7d0468a237 100644 --- a/arch/arm/dts/logicpd-som-lv-baseboard.dtsi +++ b/arch/arm/dts/logicpd-som-lv-baseboard.dtsi @@ -51,6 +51,8 @@ &mcbsp2 { status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; }; &charger { @@ -77,7 +79,7 @@ }; &dss { - status = "ok"; + status = "okay"; vdds_dsi-supply = <&vpll2>; vdda_video-supply = <&video_reg>; pinctrl-names = "default"; @@ -102,35 +104,18 @@ regulator-max-microvolt = <3300000>; }; - lcd0: display@0 { - compatible = "panel-dpi"; - label = "28"; - status = "okay"; - /* default-on; */ + lcd0: display { + /* This isn't the exact LCD, but the timings meet spec */ + compatible = "logicpd,type28"; pinctrl-names = "default"; pinctrl-0 = <&lcd_enable_pin>; - enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */ + backlight = <&bl>; + enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; port { lcd_in: endpoint { remote-endpoint = <&dpi_out>; }; }; - - panel-timing { - clock-frequency = <9000000>; - hactive = <480>; - vactive = <272>; - hfront-porch = <3>; - hback-porch = <2>; - hsync-len = <42>; - vback-porch = <3>; - vfront-porch = <2>; - vsync-len = <11>; - hsync-active = <1>; - vsync-active = <1>; - de-active = <1>; - pixelclk-active = <0>; - }; }; bl: backlight { diff --git a/arch/arm/dts/logicpd-som-lv.dtsi b/arch/arm/dts/logicpd-som-lv.dtsi index b56524cc7f..385bc8d793 100644 --- a/arch/arm/dts/logicpd-som-lv.dtsi +++ b/arch/arm/dts/logicpd-som-lv.dtsi @@ -27,6 +27,8 @@ /* HS USB Host PHY on PORT 1 */ hsusb2_phy: hsusb2_phy { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_reset_pin>; compatible = "usb-nop-xceiv"; reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */ #phy-cells = <0>; @@ -144,6 +146,8 @@ }; &usbhshost { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb2_pins>, <&hsusb2_2_pins>; port2-mode = "ehci-phy"; }; @@ -153,8 +157,6 @@ &omap3_pmx_core { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb2_pins>; mmc3_pins: pinmux_mm3_pins { pinctrl-single,pins = < @@ -166,6 +168,7 @@ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */ >; }; + mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */ @@ -183,6 +186,7 @@ OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */ >; }; + mcspi1_pins: pinmux_mcspi1_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ @@ -250,13 +254,13 @@ }; &omap3_pmx_wkup { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb2_reset_pin>; + hsusb2_reset_pin: pinmux_hsusb1_reset_pin { pinctrl-single,pins = < OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ >; }; + wl127x_gpio: pinmux_wl127x_gpio_pin { pinctrl-single,pins = < OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */ @@ -265,21 +269,6 @@ }; }; -&omap3_pmx_core2 { - pinctrl-names = "default"; - pinctrl-0 = <&hsusb2_2_pins>; - hsusb2_2_pins: pinmux_hsusb2_2_pins { - pinctrl-single,pins = < - OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ - OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ - OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ - OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ - OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ - OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ - >; - }; -}; - &uart2 { interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>; pinctrl-names = "default"; -- 2.34.1

2 3

[PATCH] ARM: am3517-evm: Remove more non-DM legacy ethernet reset code
by Adam Ford 14 Mar '22

14 Mar '22

The ethernet controller is DM compliant, and the device tree defines it. There is no need to manually handle pulling the ethernet out of reset. Signed-off-by: Adam Ford <aford173(a)gmail.com> diff --git a/board/logicpd/am3517evm/am3517evm.c b/board/logicpd/am3517evm/am3517evm.c index f014165928..e787441c74 100644 --- a/board/logicpd/am3517evm/am3517evm.c +++ b/board/logicpd/am3517evm/am3517evm.c @@ -117,17 +117,10 @@ static void am3517_evm_musb_init(void) */ int misc_init_r(void) { - u32 reset; - omap_die_id_display(); am3517_evm_musb_init(); - /* ensure that the Ethernet module is out of reset */ - reset = readl(AM3517_IP_SW_RESET); - reset &= (~CPGMACSS_SW_RST); - writel(reset, AM3517_IP_SW_RESET); - return 0; } @@ -142,7 +135,6 @@ void set_muxconf_regs(void) MUX_AM3517EVM(); } - #if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET) int board_eth_init(struct bd_info *bis) { -- 2.34.1

3 2

[PATCH 1/4] ARM: omap3_beagle: Remove non-DM initialization
by Romain Naour 14 Mar '22

14 Mar '22

With DM_MMC working for both SPL and U-Boot, this patch removes the legacy style of initializing the MMC driver. Based on omap3_logic: 42140dd0962bc134c0aad27524d0f4cc3955f255. Signed-off-by: Romain Naour <romain.naour(a)gmail.com> --- board/ti/beagle/beagle.c | 7 ------- 1 file changed, 7 deletions(-) diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c index 888a958491..d5a122af2b 100644 --- a/board/ti/beagle/beagle.c +++ b/board/ti/beagle/beagle.c @@ -500,13 +500,6 @@ void set_muxconf_regs(void) MUX_BEAGLE(); } -#if defined(CONFIG_MMC) -int board_mmc_init(struct bd_info *bis) -{ - return omap_mmc_init(0, 0, 0, -1, -1); -} -#endif - #if defined(CONFIG_MMC) void board_mmc_power_init(void) { -- 2.35.1

2 7

[PATCH v2 0/3] J721E: Fix initialization of QSGMII PHY
by Aswath Govindraju 14 Mar '22

14 Mar '22

The following series of patches, - Fix the initialization of QSGMII PHY such that it is only applicable to J721E EVM - Remove the default setting of dorprocboot - Add boot_rprocs command in the GP bootcmd - Add phy initialization command in hs bootcmd Changes since v1: - Add checks such that the QSGMII PHY initialization is only applicable for J721E EVM - Rearranged the order of PHY initialization and boot_rpocs in the bootcmd - Added reported-bys - Split the fix into two patches. Aswath Govindraju (3): include: configs: j721e_evm.h: Fix the env variable corresponding to QSGMII PHY init configs: j721e_evm_a72_defconfig: Fix the bootcmd configs: j721e_hs_evm_a72_defconfig: Add command for initializing QSGMII PHY configs/j721e_evm_a72_defconfig | 2 +- configs/j721e_hs_evm_a72_defconfig | 2 +- include/configs/j721e_evm.h | 19 +++++++++++++++++-- 3 files changed, 19 insertions(+), 4 deletions(-) -- 2.17.1

2 6

[PATCH] ram: aspeed: Rework kconfig options
by Joel Stanley 14 Mar '22

14 Mar '22

Ensure the ASPEED related options are grouped together under the RAM option when enabling support. This also makes some minor grammar corrections and renames options so they present cleanly in menuconfig. There should be no functional change to the configuration or binary. Signed-off-by: Joel Stanley <joel(a)jms.id.au> --- drivers/ram/aspeed/Kconfig | 91 +++++++++++++++++++++----------------- 1 file changed, 51 insertions(+), 40 deletions(-) diff --git a/drivers/ram/aspeed/Kconfig b/drivers/ram/aspeed/Kconfig index 576d5af8688e..0deab8649b64 100644 --- a/drivers/ram/aspeed/Kconfig +++ b/drivers/ram/aspeed/Kconfig @@ -1,66 +1,77 @@ -if RAM || SPL_RAM +menuconfig ASPEED_RAM + bool "ASPEED SDRAM configuration" + depends on RAM && ARCH_ASPEED + default ARCH_ASPEED + help + Configuration options for DDR SDRAM on ASPEED systems. + + RAM initialisation is always built in for the platform. This menu + allows customisation of the configuration used. + +if ASPEED_RAM config ASPEED_DDR4_DUALX8 bool "Enable Dual X8 DDR4 die" - depends on DM && OF_CONTROL && ARCH_ASPEED + depends on ASPEED_RAM + help + Say Y if dual X8 DDR4 die is used on the board. The ASPEED DDRM + SRAM controller needs to know if the memory chip mounted on the + board is dual x8 die or not, otherwise it may get the wrong + size of the memory space. + +config ASPEED_BYPASS_SELFTEST + depends on ASPEED_RAM + depends on ASPEED_AST2600 + bool "Bypass self test during initialization" + help + Say Y here to bypass DRAM self test to speed up the boot time. + +config ASPEED_ECC + bool "ASPEED SDRAM ECC" + depends on ASPEED_RAM + depends on ASPEED_AST2600 help - Say Y if dual X8 DDR4 die is used on the board. The aspeed ddr sdram - controller needs to know if the memory chip mounted on the board is dual - x8 die or not. Or it may get the wrong size of the memory space. + Enable SDRAM ECC function. This configures the SDRAM controller to + perform error detection and correction, sacrificing 1/9th of the + installed RAM to do so. -if ASPEED_AST2600 + +config ASPEED_ECC_SIZE + int "ECC size: 0=driver auto-caluated" + depends on ASPEED_ECC + default 0 + help + SDRAM size with the error correcting code enabled. The unit is + in Megabytes. Noted that only the 8/9 of the configured size + can be used by the system. The remaining 1/9 will be used by + the ECC engine. If the size is set to 0, the sdram driver will + calculate the SDRAM size and set the whole range be ECC enabled. choice - prompt "DDR4 target date rate" + prompt "AST2600 DDR4 target date rate" default ASPEED_DDR4_1600 + depends on ASPEED_RAM + depends on ASPEED_AST2600 config ASPEED_DDR4_400 - bool "DDR4 targets at 400Mbps" - depends on DM && OF_CONTROL && ARCH_ASPEED + bool "400Mbps" help select DDR4 target data rate at 400M config ASPEED_DDR4_800 - bool "DDR4 targets at 800Mbps" - depends on DM && OF_CONTROL && ARCH_ASPEED + bool "800Mbps" help select DDR4 target data rate at 800M config ASPEED_DDR4_1333 - bool "DDR4 targets at 1333Mbps" - depends on DM && OF_CONTROL && ARCH_ASPEED + bool "1333Mbps" help select DDR4 target data rate at 1333M config ASPEED_DDR4_1600 - bool "DDR4 targets at 1600Mbps" - depends on DM && OF_CONTROL && ARCH_ASPEED + bool "1600Mbps" help select DDR4 target data rate at 1600M endchoice -config ASPEED_BYPASS_SELFTEST - bool "bypass self test during DRAM initialization" - help - Say Y here to bypass DRAM self test to speed up the boot time - -config ASPEED_ECC - bool "aspeed SDRAM error correcting code" - depends on DM && OF_CONTROL && ARCH_ASPEED - help - enable SDRAM ECC function - -if ASPEED_ECC -config ASPEED_ECC_SIZE - int "ECC size: 0=driver auto-caluated" - depends on ASPEED_ECC - default 0 - help - SDRAM size with the error correcting code enabled. The unit is - in Megabytes. Noted that only the 8/9 of the configured size - can be used by the system. The remaining 1/9 will be used by - the ECC engine. If the size is set to 0, the sdram driver will - calculate the SDRAM size and set the whole range be ECC enabled. -endif # end of ASPEED_ECC -endif # end of ASPEED_AST2600 -endif # end of RAM || SPL_RAM +endif # End of ASPEED_RAM -- 2.34.1

3 2

ARM: socfpga: gen5: release reset before using USB as device with ums
by Wolfgang Grandegger 14 Mar '22

14 Mar '22

The command "ums 0 mmc 0" does not work because the USB port is still in reset. Releasing it in board_usb_init() fixes the problem. This issue has been observed and fixed on the Aries MCVEVP board. Signed-off-by: Wolfgang Grandegger <wg(a)aries-embedded.de> --- arch/arm/dts/socfpga_cyclone5_mcvevk.dts | 1 + arch/arm/mach-socfpga/board.c | 8 ++++++++ arch/arm/mach-socfpga/include/mach/reset_manager_gen5.h | 2 ++ 3 files changed, 11 insertions(+) diff --git a/arch/arm/dts/socfpga_cyclone5_mcvevk.dts b/arch/arm/dts/socfpga_cyclone5_mcvevk.dts index ceaec29770..a673837f25 100644 --- a/arch/arm/dts/socfpga_cyclone5_mcvevk.dts +++ b/arch/arm/dts/socfpga_cyclone5_mcvevk.dts @@ -12,6 +12,7 @@ aliases { ethernet0 = &gmac0; stmpe-i2c0 = &stmpe1; + udc0 = &usb1; }; chosen { diff --git a/arch/arm/mach-socfpga/board.c b/arch/arm/mach-socfpga/board.c index 7267163222..a2eed73fe9 100644 --- a/arch/arm/mach-socfpga/board.c +++ b/arch/arm/mach-socfpga/board.c @@ -83,6 +83,14 @@ int board_usb_init(int index, enum usb_init_type init) /* Patch the address from OF into the controller pdata. */ socfpga_otg_data.regs_otg = addr; +#ifdef CONFIG_TARGET_SOCFPGA_GEN5 + /* First release reset of the USB port */ + if (addr == SOCFPGA_USB0_ADDRESS) + socfpga_per_reset(SOCFPGA_RESET(USB0), 0); + else if (addr == SOCFPGA_USB1_ADDRESS) + socfpga_per_reset(SOCFPGA_RESET(USB1), 0); +#endif + return dwc2_udc_probe(&socfpga_otg_data); } diff --git a/arch/arm/mach-socfpga/include/mach/reset_manager_gen5.h b/arch/arm/mach-socfpga/include/mach/reset_manager_gen5.h index d108eac1e2..611403cf00 100644 --- a/arch/arm/mach-socfpga/include/mach/reset_manager_gen5.h +++ b/arch/arm/mach-socfpga/include/mach/reset_manager_gen5.h @@ -31,6 +31,8 @@ void socfpga_bridges_reset(int enable); */ #define RSTMGR_EMAC0 RSTMGR_DEFINE(1, 0) #define RSTMGR_EMAC1 RSTMGR_DEFINE(1, 1) +#define RSTMGR_USB0 RSTMGR_DEFINE(1, 2) +#define RSTMGR_USB1 RSTMGR_DEFINE(1, 3) #define RSTMGR_NAND RSTMGR_DEFINE(1, 4) #define RSTMGR_QSPI RSTMGR_DEFINE(1, 5) #define RSTMGR_L4WD0 RSTMGR_DEFINE(1, 6) -- 2.25.1

2 5