March 2022 - U-Boot

[PATCH] include: configs: *imx8*: remove IMX_FEC_BASE
by Heiko Thiery 12 Apr '22

12 Apr '22

The IMX_FEC_BASE value is not used when CONFIG_DM_ETH is configured. So this value can be removed. Signed-off-by: Heiko Thiery <heiko.thiery(a)gmail.com> --- include/configs/imx8mm-cl-iot-gate.h | 2 -- include/configs/imx8mm_beacon.h | 1 - include/configs/imx8mm_evk.h | 2 -- include/configs/imx8mm_venice.h | 1 - include/configs/imx8mn_beacon.h | 1 - include/configs/imx8mq_evk.h | 2 -- include/configs/imx8mq_phanbell.h | 2 -- include/configs/imx8ulp_evk.h | 2 -- include/configs/kontron_pitx_imx8m.h | 1 - include/configs/pico-imx8mq.h | 2 -- include/configs/verdin-imx8mm.h | 1 - 11 files changed, 17 deletions(-) diff --git a/include/configs/imx8mm-cl-iot-gate.h b/include/configs/imx8mm-cl-iot-gate.h index 7e6be6050c..4413bdcc58 100644 --- a/include/configs/imx8mm-cl-iot-gate.h +++ b/include/configs/imx8mm-cl-iot-gate.h @@ -157,8 +157,6 @@ #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 - /* USB Configs */ #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) diff --git a/include/configs/imx8mm_beacon.h b/include/configs/imx8mm_beacon.h index 77f062474d..029e8c4c7f 100644 --- a/include/configs/imx8mm_beacon.h +++ b/include/configs/imx8mm_beacon.h @@ -109,6 +109,5 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 #endif diff --git a/include/configs/imx8mm_evk.h b/include/configs/imx8mm_evk.h index c7022ef0f7..771eaf80d5 100644 --- a/include/configs/imx8mm_evk.h +++ b/include/configs/imx8mm_evk.h @@ -89,6 +89,4 @@ #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 - #endif diff --git a/include/configs/imx8mm_venice.h b/include/configs/imx8mm_venice.h index 7ab11cc8fb..a828f48d2e 100644 --- a/include/configs/imx8mm_venice.h +++ b/include/configs/imx8mm_venice.h @@ -109,6 +109,5 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 #endif diff --git a/include/configs/imx8mn_beacon.h b/include/configs/imx8mn_beacon.h index e2e322bb4d..e54b87c76a 100644 --- a/include/configs/imx8mn_beacon.h +++ b/include/configs/imx8mn_beacon.h @@ -126,7 +126,6 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 #endif /* CONFIG_FEC_MXC */ #endif diff --git a/include/configs/imx8mq_evk.h b/include/configs/imx8mq_evk.h index 4aaed3ae7d..1a472588ac 100644 --- a/include/configs/imx8mq_evk.h +++ b/include/configs/imx8mq_evk.h @@ -43,8 +43,6 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC - -#define IMX_FEC_BASE 0x30BE0000 #endif #ifndef CONFIG_SPL_BUILD diff --git a/include/configs/imx8mq_phanbell.h b/include/configs/imx8mq_phanbell.h index 16a2c2cf9d..1e1c186aed 100644 --- a/include/configs/imx8mq_phanbell.h +++ b/include/configs/imx8mq_phanbell.h @@ -37,8 +37,6 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC - -#define IMX_FEC_BASE 0x30BE0000 #endif #define CONFIG_MFG_ENV_SETTINGS \ diff --git a/include/configs/imx8ulp_evk.h b/include/configs/imx8ulp_evk.h index 7da6802aa5..666306c028 100644 --- a/include/configs/imx8ulp_evk.h +++ b/include/configs/imx8ulp_evk.h @@ -34,8 +34,6 @@ #define CONFIG_FEC_XCV_TYPE RMII #define CONFIG_FEC_MXC_PHYADDR 1 - -#define IMX_FEC_BASE 0x29950000 #endif #ifdef CONFIG_DISTRO_DEFAULTS diff --git a/include/configs/kontron_pitx_imx8m.h b/include/configs/kontron_pitx_imx8m.h index 0f96b905ab..6f426cb08c 100644 --- a/include/configs/kontron_pitx_imx8m.h +++ b/include/configs/kontron_pitx_imx8m.h @@ -43,7 +43,6 @@ #define CONFIG_FEC_MXC_PHYADDR 0 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 #define PHY_ANEG_TIMEOUT 20000 #endif diff --git a/include/configs/pico-imx8mq.h b/include/configs/pico-imx8mq.h index 7bfa79059a..08204779d8 100644 --- a/include/configs/pico-imx8mq.h +++ b/include/configs/pico-imx8mq.h @@ -37,8 +37,6 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 1 #define FEC_QUIRK_ENET_MAC - -#define IMX_FEC_BASE 0x30BE0000 #endif /* Initial environment variables */ diff --git a/include/configs/verdin-imx8mm.h b/include/configs/verdin-imx8mm.h index 17583c0a6a..859b62d6f7 100644 --- a/include/configs/verdin-imx8mm.h +++ b/include/configs/verdin-imx8mm.h @@ -107,7 +107,6 @@ #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 7 #define FEC_QUIRK_ENET_MAC -#define IMX_FEC_BASE 0x30BE0000 /* USB Configs */ #define CONFIG_EHCI_HCD_INIT_AFTER_RESET -- 2.20.1

5 4

[PATCH] ARM: imx: romapi: Repair FlexSPI NOR boot offset
by Marek Vasut 12 Apr '22

12 Apr '22

The FlexSPI NOR boot offset does not require any special handling, the image_offset is correct in either case (0x1000 for FlexSPI NOR and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the case on MX8MN/MX8MP. The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in case of the MX8MN/MX8MP, but fixing that needs additional plumbing. Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Fabio Estevam <festevam(a)denx.de> Cc: Peng Fan <peng.fan(a)nxp.com> Cc: Stefano Babic <sbabic(a)denx.de> --- arch/arm/mach-imx/spl_imx_romapi.c | 10 ++-------- 1 file changed, 2 insertions(+), 8 deletions(-) diff --git a/arch/arm/mach-imx/spl_imx_romapi.c b/arch/arm/mach-imx/spl_imx_romapi.c index d827de375a6..c47f5a6bdb4 100644 --- a/arch/arm/mach-imx/spl_imx_romapi.c +++ b/arch/arm/mach-imx/spl_imx_romapi.c @@ -38,14 +38,8 @@ ulong spl_romapi_raw_seekable_read(u32 offset, u32 size, void *buf) ulong __weak spl_romapi_get_uboot_base(u32 image_offset, u32 rom_bt_dev) { - u32 offset; - - if (((rom_bt_dev >> 16) & 0xff) == BT_DEV_TYPE_FLEXSPINOR) - offset = CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512; - else - offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000; - - return offset; + return image_offset + + (CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000); } static int is_boot_from_stream_device(u32 boot) -- 2.34.1

5 19

[PATCH] spi: nxp_fspi: Add i.MX8MP compatible string
by Marek Vasut 12 Apr '22

12 Apr '22

The i.MX8M Mini and i.MX8M Plus flexspi IPs are compatible with one another, however the linux kernel DT uses separate compatible string for each SoC. Add the missing i.MX8MP compatible into this driver. Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Fabio Estevam <festevam(a)denx.de> Cc: Peng Fan <peng.fan(a)nxp.com> Cc: Stefano Babic <sbabic(a)denx.de> --- drivers/spi/nxp_fspi.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/spi/nxp_fspi.c b/drivers/spi/nxp_fspi.c index b7c922b1dfd..607c953987b 100644 --- a/drivers/spi/nxp_fspi.c +++ b/drivers/spi/nxp_fspi.c @@ -1053,6 +1053,7 @@ static const struct dm_spi_ops nxp_fspi_ops = { static const struct udevice_id nxp_fspi_ids[] = { { .compatible = "nxp,lx2160a-fspi", .data = (ulong)&lx2160a_data, }, { .compatible = "nxp,imx8mm-fspi", .data = (ulong)&imx8mm_data, }, + { .compatible = "nxp,imx8mp-fspi", .data = (ulong)&imx8mm_data, }, { } }; -- 2.34.1

3 2

[PATCH] mmc: fsl_esdhc_imx: Add i.MX8MP compatible string
by Marek Vasut 12 Apr '22

12 Apr '22

Add compatible string for i.MX8MP, which permits i.MX8MP to use HS400ES mode, just like all the other i.MX8M. Signed-off-by: Marek Vasut <marex(a)denx.de> Cc: Fabio Estevam <festevam(a)denx.de> Cc: Haibo Chen <haibo.chen(a)nxp.com> Cc: Peng Fan <peng.fan(a)nxp.com> Cc: Stefano Babic <sbabic(a)denx.de> --- drivers/mmc/fsl_esdhc_imx.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c index a38bc13a1e6..6ab2f1bbe76 100644 --- a/drivers/mmc/fsl_esdhc_imx.c +++ b/drivers/mmc/fsl_esdhc_imx.c @@ -1638,6 +1638,7 @@ static const struct udevice_id fsl_esdhc_ids[] = { { .compatible = "fsl,imx8qm-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, { .compatible = "fsl,imx8mm-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, { .compatible = "fsl,imx8mn-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, + { .compatible = "fsl,imx8mp-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, { .compatible = "fsl,imx8mq-usdhc", .data = (ulong)&usdhc_imx8qm_data,}, { .compatible = "fsl,imxrt-usdhc", }, { .compatible = "fsl,esdhc", }, -- 2.34.1

4 3

[PATCH] board: gateworks venice: add support for GPY111 phy
by Tim Harvey 12 Apr '22

12 Apr '22

The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy due to part availability. Add support for it by adding LED config and dt-prop based internal delay config tx-delay/rx-delay per PHY ID. Signed-off-by: Tim Harvey <tharvey(a)gateworks.com> --- board/gateworks/venice/venice.c | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/board/gateworks/venice/venice.c b/board/gateworks/venice/venice.c index 5334500ef6a7..425c69056da5 100644 --- a/board/gateworks/venice/venice.c +++ b/board/gateworks/venice/venice.c @@ -63,6 +63,7 @@ static int setup_fec(void) int board_phy_config(struct phy_device *phydev) { unsigned short val; + ofnode node; switch (phydev->phy_id) { case 0x2000a231: /* TI DP83867 GbE PHY */ @@ -73,6 +74,21 @@ int board_phy_config(struct phy_device *phydev) val |= 0xb << 8; /* LED2(Green;Link/Act): blink for TX/RX act */ phy_write(phydev, MDIO_DEVAD_NONE, 24, val); break; + case 0xd565a401: /* MaxLinear GPY111 */ + puts("GPY111 "); + node = phy_get_ofnode(phydev); + if (ofnode_valid(node)) { + u32 rx_delay, tx_delay; + + rx_delay = ofnode_read_u32_default(node, "rx-internal-delay-ps", 2000); + tx_delay = ofnode_read_u32_default(node, "tx-internal-delay-ps", 2000); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0x17); + val &= ~((0x7 << 12) | (0x7 << 8)); + val |= (rx_delay / 500) << 12; + val |= (tx_delay / 500) << 8; + phy_write(phydev, MDIO_DEVAD_NONE, 0x17, val); + } + break; } if (phydev->drv->config) -- 2.17.1

3 2

[PATCH] imx8m{m,n}-venice-gw7902: add GSC ADC rail for VDD_5P0
by Tim Harvey 12 Apr '22

12 Apr '22

The GW7902-C revision adds an ADC for the VDD_5P0 voltage rail. Add register definitions for it. Signed-off-by: Tim Harvey <tharvey(a)gateworks.com> --- arch/arm/dts/imx8mm-venice-gw7902.dts | 7 +++++++ arch/arm/dts/imx8mn-venice-gw7902.dts | 7 +++++++ 2 files changed, 14 insertions(+) diff --git a/arch/arm/dts/imx8mm-venice-gw7902.dts b/arch/arm/dts/imx8mm-venice-gw7902.dts index d37ffc050da2..adf521632d63 100644 --- a/arch/arm/dts/imx8mm-venice-gw7902.dts +++ b/arch/arm/dts/imx8mm-venice-gw7902.dts @@ -348,6 +348,13 @@ gw,voltage-divider-ohms = <10000 10000>; }; + channel@9c { + gw,mode = <2>; + reg = <0x9c>; + label = "vdd_5p0"; + gw,voltage-divider-ohms = <10000 10000>; + }; + channel@a2 { gw,mode = <2>; reg = <0xa2>; diff --git a/arch/arm/dts/imx8mn-venice-gw7902.dts b/arch/arm/dts/imx8mn-venice-gw7902.dts index d3c08e59c542..29897c161b96 100644 --- a/arch/arm/dts/imx8mn-venice-gw7902.dts +++ b/arch/arm/dts/imx8mn-venice-gw7902.dts @@ -347,6 +347,13 @@ gw,voltage-divider-ohms = <10000 10000>; }; + channel@9c { + gw,mode = <2>; + reg = <0x9c>; + label = "vdd_5p0"; + gw,voltage-divider-ohms = <10000 10000>; + }; + channel@a2 { gw,mode = <2>; reg = <0xa2>; -- 2.17.1

3 2

[PATCH] imx8m{m,n}_venice: update boot_net script to load fdt
by Tim Harvey 12 Apr '22

12 Apr '22

Update the 'boot_net' script to load the fdt with the kernel. Signed-off-by: Tim Harvey <tharvey(a)gateworks.com> --- include/configs/imx8mm_venice.h | 17 +++++++++++++++-- include/configs/imx8mn_venice.h | 17 +++++++++++++++-- 2 files changed, 30 insertions(+), 4 deletions(-) diff --git a/include/configs/imx8mm_venice.h b/include/configs/imx8mm_venice.h index cbb138229f67..fad304b22bdd 100644 --- a/include/configs/imx8mm_venice.h +++ b/include/configs/imx8mm_venice.h @@ -62,9 +62,22 @@ "setexpr blkcnt $blkcnt / 0x200 && " \ "mmc dev $dev && " \ "mmc write $loadaddr 0x42 $blkcnt\0" \ + "loadfdt=" \ + "if $fsload $fdt_addr_r $dir/$fdt_file1; " \ + "then echo loaded $fdt_file1; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file2; " \ + "then echo loaded $fdt_file2; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file3; " \ + "then echo loaded $fdt_file3; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file4; " \ + "then echo loaded $fdt_file4; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file5; " \ + "then echo loaded $fdt_file5; " \ + "fi\0" \ "boot_net=" \ - "tftpboot $kernel_addr_r $image && " \ - "booti $kernel_addr_r - $fdtcontroladdr\0" \ + "setenv fsload tftpboot; " \ + "run loadfdt && tftpboot $kernel_addr_r $dir/Image && " \ + "booti $kernel_addr_r - $fdt_addr_r\0" \ "update_rootfs=" \ "tftpboot $loadaddr $image && " \ "gzwrite mmc $dev $loadaddr $filesize 100000 1000000\0" \ diff --git a/include/configs/imx8mn_venice.h b/include/configs/imx8mn_venice.h index 4c95893be4fc..85a96537b066 100644 --- a/include/configs/imx8mn_venice.h +++ b/include/configs/imx8mn_venice.h @@ -59,9 +59,22 @@ "setexpr blkcnt $blkcnt / 0x200 && " \ "mmc dev $dev && " \ "mmc write $loadaddr 0x40 $blkcnt\0" \ + "loadfdt=" \ + "if $fsload $fdt_addr_r $dir/$fdt_file1; " \ + "then echo loaded $fdt_file1; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file2; " \ + "then echo loaded $fdt_file2; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file3; " \ + "then echo loaded $fdt_file3; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file4; " \ + "then echo loaded $fdt_file4; " \ + "elif $fsload $fdt_addr_r $dir/$fdt_file5; " \ + "then echo loaded $fdt_file5; " \ + "fi\0" \ "boot_net=" \ - "tftpboot $kernel_addr_r $image && " \ - "booti $kernel_addr_r - $fdtcontroladdr\0" \ + "setenv fsload tftpboot; " \ + "run loadfdt && tftpboot $kernel_addr_r $dir/Image && " \ + "booti $kernel_addr_r - $fdt_addr_r\0" \ "update_rootfs=" \ "tftpboot $loadaddr $image && " \ "gzwrite mmc $dev $loadaddr $filesize 100000 1000000\0" \ -- 2.17.1

3 2

[PATCH v2] kontron-sl-mx8mm: change environment address variables
by Heiko Thiery 12 Apr '22

12 Apr '22

Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB. To have enought space to load kernel images bigger than 32MB change the variables to a feasible value. The new environment variables layout is based on the scheme from "include/configs/ti_armv7_common.h". The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have the same value as for the kernel_addr_r. Signed-off-by: Heiko Thiery <heiko.thiery(a)gmail.com> Reviewed-by: Michael Walle <michael(a)walle.cc> --- configs/kontron-sl-mx8mm_defconfig | 2 +- include/configs/kontron-sl-mx8mm.h | 15 ++++++++++----- 2 files changed, 11 insertions(+), 6 deletions(-) diff --git a/configs/kontron-sl-mx8mm_defconfig b/configs/kontron-sl-mx8mm_defconfig index 940bf07a92..030e2251e7 100644 --- a/configs/kontron-sl-mx8mm_defconfig +++ b/configs/kontron-sl-mx8mm_defconfig @@ -20,7 +20,7 @@ CONFIG_SPL_SERIAL=y CONFIG_BOOTCOUNT_BOOTLIMIT=3 CONFIG_SPL=y CONFIG_DISTRO_DEFAULTS=y -CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_SYS_LOAD_ADDR=0x42000000 CONFIG_FIT=y CONFIG_FIT_EXTERNAL_OFFSET=0x3000 CONFIG_SPL_LOAD_FIT=y diff --git a/include/configs/kontron-sl-mx8mm.h b/include/configs/kontron-sl-mx8mm.h index d1e87f97d6..788ae77cd3 100644 --- a/include/configs/kontron-sl-mx8mm.h +++ b/include/configs/kontron-sl-mx8mm.h @@ -67,15 +67,20 @@ #define FEC_QUIRK_ENET_MAC -#define CONFIG_EXTRA_ENV_SETTINGS \ +#define ENV_MEM_LAYOUT_SETTINGS \ + "loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ "kernel_addr_r=0x42000000\0" \ - "fdt_addr_r=0x44000000\0" \ - "ramdisk_addr_r=0x46400000\0" \ - "pxefile_addr_r=0x46000000\0" \ - "scriptaddr=0x46000000\0" \ + "fdt_addr_r=0x48000000\0" \ + "fdtoverlay_addr_r=0x49000000\0" \ + "ramdisk_addr_r=0x48080000\0" \ + "scriptaddr=0x40000000\0"\ + "pxefile_addr_r=0x40100000\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ "dfu_alt_info=sf 0:0=flash-bin raw 0x400 0x1f0000\0" \ "bootdelay=3\0" \ "hostname=" CONFIG_HOSTNAME "\0" \ + ENV_MEM_LAYOUT_SETTINGS \ BOOTENV #endif /* __KONTRON_MX8MM_CONFIG_H */ -- 2.30.2

2 3

[PATCH] rpi: always set fdt_addr to the correct value
by Marek Szyprowski 12 Apr '22

12 Apr '22

The fdt_addr env have meaning only for the current runtime and it depends on the dtb size or firmware version. If one save the environment to disk and the loads it on the latter boot, the fdt_addr might change, what result in passing incorrect dtb address to the kernel. Fix this by always setting the fdt_addr env. This fixes system operation after saving the env to disk and updating i.e. dtb files or firmware. Signed-off-by: Marek Szyprowski <m.szyprowski(a)samsung.com> --- board/raspberrypi/rpi/rpi.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c index bc3cc597adb..6d6d2e69234 100644 --- a/board/raspberrypi/rpi/rpi.c +++ b/board/raspberrypi/rpi/rpi.c @@ -347,9 +347,6 @@ static void set_fdtfile(void) */ static void set_fdt_addr(void) { - if (env_get("fdt_addr")) - return; - if (fdt_magic(fw_dtb_pointer) != FDT_MAGIC) return; -- 2.17.1

4 5

[PATCH] net: tftp: fix tftp server initialization
by Arjan Minzinga Zijlstra 12 Apr '22

12 Apr '22

Some globals where not properly initialized causing timeouts as data packets where not immediately acknowledged. Signed-off-by: Arjan Minzinga Zijlstra <arjan.minzingazijlstra(a)fox-it.com> --- net/tftp.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/tftp.c b/net/tftp.c index 62a9648474..9d5fe2f2d9 100644 --- a/net/tftp.c +++ b/net/tftp.c @@ -912,6 +912,8 @@ void tftp_start_server(void) tftp_block_size = TFTP_BLOCK_SIZE; tftp_cur_block = 0; tftp_our_port = WELL_KNOWN_PORT; + tftp_windowsize = 1; + tftp_next_ack = tftp_windowsize; #ifdef CONFIG_TFTP_TSIZE tftp_tsize = 0; -- 2.25.1

2 2