February 2022 - U-Boot

[PATCH] dm: pinctrl: Use explicit values for enums
by Michal Simek 07 Mar '22

07 Mar '22

From: Ashok Reddy Soma <ashok.reddy.soma(a)xilinx.com> Based on discussion at https://lore.kernel.org/r/20200318125003.GA2727094@kroah.com we got recommendation to use explicit values for all enums. So, add explicit values to all pinctrl related enums for readability. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma(a)xilinx.com> Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> --- include/dm/pinctrl.h | 48 ++++++++++++++++++++++---------------------- 1 file changed, 24 insertions(+), 24 deletions(-) diff --git a/include/dm/pinctrl.h b/include/dm/pinctrl.h index 8b869c4fbfb7..0c461e56bb48 100644 --- a/include/dm/pinctrl.h +++ b/include/dm/pinctrl.h @@ -453,30 +453,30 @@ struct pinctrl_ops { * presented using the packed format. */ enum pin_config_param { - PIN_CONFIG_BIAS_BUS_HOLD, - PIN_CONFIG_BIAS_DISABLE, - PIN_CONFIG_BIAS_HIGH_IMPEDANCE, - PIN_CONFIG_BIAS_PULL_DOWN, - PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, - PIN_CONFIG_BIAS_PULL_UP, - PIN_CONFIG_DRIVE_OPEN_DRAIN, - PIN_CONFIG_DRIVE_OPEN_SOURCE, - PIN_CONFIG_DRIVE_PUSH_PULL, - PIN_CONFIG_DRIVE_STRENGTH, - PIN_CONFIG_DRIVE_STRENGTH_UA, - PIN_CONFIG_INPUT_DEBOUNCE, - PIN_CONFIG_INPUT_ENABLE, - PIN_CONFIG_INPUT_SCHMITT, - PIN_CONFIG_INPUT_SCHMITT_ENABLE, - PIN_CONFIG_LOW_POWER_MODE, - PIN_CONFIG_OUTPUT_ENABLE, - PIN_CONFIG_OUTPUT, - PIN_CONFIG_POWER_SOURCE, - PIN_CONFIG_SLEEP_HARDWARE_STATE, - PIN_CONFIG_SLEW_RATE, - PIN_CONFIG_SKEW_DELAY, - PIN_CONFIG_END = 0x7F, - PIN_CONFIG_MAX = 0xFF, + PIN_CONFIG_BIAS_BUS_HOLD = 0, + PIN_CONFIG_BIAS_DISABLE = 1, + PIN_CONFIG_BIAS_HIGH_IMPEDANCE = 2, + PIN_CONFIG_BIAS_PULL_DOWN = 3, + PIN_CONFIG_BIAS_PULL_PIN_DEFAULT = 4, + PIN_CONFIG_BIAS_PULL_UP = 5, + PIN_CONFIG_DRIVE_OPEN_DRAIN = 6, + PIN_CONFIG_DRIVE_OPEN_SOURCE = 7, + PIN_CONFIG_DRIVE_PUSH_PULL = 8, + PIN_CONFIG_DRIVE_STRENGTH = 9, + PIN_CONFIG_DRIVE_STRENGTH_UA = 10, + PIN_CONFIG_INPUT_DEBOUNCE = 11, + PIN_CONFIG_INPUT_ENABLE = 12, + PIN_CONFIG_INPUT_SCHMITT = 13, + PIN_CONFIG_INPUT_SCHMITT_ENABLE = 14, + PIN_CONFIG_LOW_POWER_MODE = 15, + PIN_CONFIG_OUTPUT_ENABLE = 16, + PIN_CONFIG_OUTPUT = 17, + PIN_CONFIG_POWER_SOURCE = 18, + PIN_CONFIG_SLEEP_HARDWARE_STATE = 19, + PIN_CONFIG_SLEW_RATE = 20, + PIN_CONFIG_SKEW_DELAY = 21, + PIN_CONFIG_END = 127, /* 0x7F */ + PIN_CONFIG_MAX = 255, /* 0xFF */ }; #if CONFIG_IS_ENABLED(PINCTRL_GENERIC) -- 2.35.1

3 2

[PATCH 00/24] binman: rockchip: Migrate from rockchip SPL_FIT_GENERATOR script
by Simon Glass 06 Mar '22

06 Mar '22

At present rockchip 64-bit boards make use of a FIT-generator script written in Python. The script supports splitting an ELF file into several 'loadable' nodes in the FIT. Binman does not current support this feature. This series adds binman support for ELF splitting. This works by adding a new 'fit,operation' property to the FIT subnodes, allowing this new way of generating nodes. Some other fixes and improvements are needed along the way. A new, common binman description is added for 64-bit boards which includes the required u-boot.itb file. The existing script is removed, so that only a few zynq boards are now using a SPL_FIT_GENERATOR script: avnet_ultrazedev_cc_v1_0_ultrazedev_som_v1_0 xilinx_zynqmp_virt Migration of those is hopefully in progress. Note however that tools/k3_fit_atf.sh remains, used by a few boards that enable CONFIG_TI_SECURE_DEVICE so this series is copied there too: am335x_hs_evm am335x_hs_evm_uart am43xx_hs_evm am57xx_hs_evm am57xx_hs_evm_usb am65x_hs_evm_a53 am65x_hs_evm_r5 dra7xx_hs_evm dra7xx_hs_evm_usb j721e_hs_evm_a72 j721e_hs_evm_r5 k2e_hs_evm k2g_hs_evm k2hk_hs_evm k2l_hs_evm Ivan Mikhaylov has sent a patch to help with these, but I need to take a look at the testing side. In any case they should really be using binman for the image generation. This series also includes some moveconfig improvements that were used to create board lists in this cover letter. Simon Glass (24): moveconfig: Show the config name rather than the defconfig moveconfig: Allow regex matches when finding combinations spl: x86: Correct the binman symbols for SPL spl: Allow disabling binman symbols in SPL rockchip: evb-rk3288: Drop raw-image support dtoc: Support adding a string list to a device tree dtoc: Support deleting a node dtoc: Allow deleting nodes and adding them in the same sync dtoc: Support reading a list of arguments binman: Update docs to indicate mkimage is supported elf: Add a way to read segment information from an ELF file WIP: binman: Add support for OP-TEE binman: Add to the TODO binman: Support a list of strings with the mkimage etype binman: Add a ELF test file with disjoint text sections binman: Move entry-data collection into a Entry method binman: fit: Refactor to reduce function size binman: Tidy up the docs a little with fit binman: Allow different operations in FIT generator nodes binman: Support splitting an ELF file into multiple nodes rockchip: Include binman script in 64-bit boards rockchip: Support building the all output files in binman rockchip: Convert all boards to use binman rockchip: Drop the FIT generator script Makefile | 43 +- arch/arm/dts/px30-u-boot.dtsi | 2 + arch/arm/dts/rk3308-u-boot.dtsi | 2 + arch/arm/dts/rk3326-odroid-go2-u-boot.dtsi | 2 + arch/arm/dts/rk3328-u-boot.dtsi | 2 + arch/arm/dts/rk3368-u-boot.dtsi | 1 + arch/arm/dts/rk3399-u-boot.dtsi | 5 +- arch/arm/dts/rk3568-u-boot.dtsi | 2 + arch/arm/dts/rockchip-u-boot.dtsi | 84 +++- arch/arm/mach-rockchip/Kconfig | 6 + arch/arm/mach-rockchip/make_fit_atf.py | 240 --------- arch/x86/dts/u-boot.dtsi | 2 +- boot/Kconfig | 3 +- common/spl/Kconfig | 24 + common/spl/spl.c | 12 +- configs/evb-rk3288_defconfig | 1 + include/spl.h | 4 +- tools/binman/binman.rst | 98 +++- tools/binman/elf.py | 37 ++ tools/binman/elf_test.py | 31 +- tools/binman/entries.rst | 260 +++++++++- tools/binman/entry.py | 28 ++ tools/binman/etype/fit.py | 490 ++++++++++++++++--- tools/binman/etype/mkimage.py | 27 +- tools/binman/etype/op_tee.py | 23 + tools/binman/ftest.py | 123 +++++ tools/binman/missing-blob-help | 4 + tools/binman/test/220_fit_bad_oper.dts | 27 + tools/binman/test/221_fit_split_elf.dts | 67 +++ tools/binman/test/222_fit_bad_dir.dts | 9 + tools/binman/test/223_fit_bad_dir_config.dts | 9 + tools/binman/test/Makefile | 6 +- tools/binman/test/elf_sections.c | 20 + tools/binman/test/elf_sections.lds | 31 ++ tools/dtoc/fdt.py | 37 ++ tools/dtoc/fdt_util.py | 12 + tools/dtoc/test/dtoc_test_simple.dts | 1 + tools/dtoc/test_fdt.py | 43 ++ tools/moveconfig.py | 39 +- 39 files changed, 1450 insertions(+), 407 deletions(-) delete mode 100755 arch/arm/mach-rockchip/make_fit_atf.py create mode 100644 tools/binman/etype/op_tee.py create mode 100644 tools/binman/test/220_fit_bad_oper.dts create mode 100644 tools/binman/test/221_fit_split_elf.dts create mode 100644 tools/binman/test/222_fit_bad_dir.dts create mode 100644 tools/binman/test/223_fit_bad_dir_config.dts create mode 100644 tools/binman/test/elf_sections.c create mode 100644 tools/binman/test/elf_sections.lds -- 2.35.0.263.gb82422642f-goog

3 68

[PATCH 1/1] cmd: pwm: fix typo 'eisable' -> 'disable'
by Sébastien Szymanski 05 Mar '22

05 Mar '22

Fixed misspelled 'disable' in help text. Signed-off-by: Sébastien Szymanski <sebastien.szymanski(a)armadeus.com> --- cmd/pwm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/cmd/pwm.c b/cmd/pwm.c index 7947e61aee..7e82955239 100644 --- a/cmd/pwm.c +++ b/cmd/pwm.c @@ -111,5 +111,5 @@ U_BOOT_CMD(pwm, 6, 0, do_pwm, "invert <pwm_dev_num> <channel> <polarity> - invert polarity\n" "pwm config <pwm_dev_num> <channel> <period_ns> <duty_ns> - config PWM\n" "pwm enable <pwm_dev_num> <channel> - enable PWM output\n" - "pwm disable <pwm_dev_num> <channel> - eisable PWM output\n" + "pwm disable <pwm_dev_num> <channel> - disable PWM output\n" "Note: All input values are in decimal"); -- 2.34.1

3 2

[PATCH] arm: dts: iot2050: Add cfg register space for ringacc and udmap
by Jan Kiszka 05 Mar '22

05 Mar '22

From: Jan Kiszka <jan.kiszka(a)siemens.com> Recent unrelated fixes (9876ae7db6da) revealed that we were missing bits from 2af181b53e28 in the IOT2050 dt. Add them, but only for main U-Boot. SPL loads from QSPI only, thus cannot use DMA. Signed-off-by: Jan Kiszka <jan.kiszka(a)siemens.com> --- .../dts/k3-am65-iot2050-common-u-boot.dtsi | 25 ++++++++++++++++++- 1 file changed, 24 insertions(+), 1 deletion(-) diff --git a/arch/arm/dts/k3-am65-iot2050-common-u-boot.dtsi b/arch/arm/dts/k3-am65-iot2050-common-u-boot.dtsi index 286e25f3794..d80c5501d2f 100644 --- a/arch/arm/dts/k3-am65-iot2050-common-u-boot.dtsi +++ b/arch/arm/dts/k3-am65-iot2050-common-u-boot.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 /* - * Copyright (c) Siemens AG, 2018-2021 + * Copyright (c) Siemens AG, 2018-2022 * * Authors: * Le Jin <le.jin(a)siemens.com> @@ -27,6 +27,29 @@ &cbass_mcu { u-boot,dm-spl; + + mcu_navss: bus@28380000 { + ringacc@2b800000 { + reg = <0x0 0x2b800000 0x0 0x400000>, + <0x0 0x2b000000 0x0 0x400000>, + <0x0 0x28590000 0x0 0x100>, + <0x0 0x2a500000 0x0 0x40000>, + <0x0 0x28440000 0x0 0x40000>; + reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target", "cfg"; + ti,dma-ring-reset-quirk; + }; + + dma-controller@285c0000 { + reg = <0x0 0x285c0000 0x0 0x100>, + <0x0 0x284c0000 0x0 0x4000>, + <0x0 0x2a800000 0x0 0x40000>, + <0x0 0x284a0000 0x0 0x4000>, + <0x0 0x2aa00000 0x0 0x40000>, + <0x0 0x28400000 0x0 0x2000>; + reg-names = "gcfg", "rchan", "rchanrt", "tchan", + "tchanrt", "rflow"; + }; + }; }; &cbass_wakeup { -- 2.34.1

2 1

[PATCH] configs: j721e_*_evm_a72_defconfig: Enable config for setting mmc speed mode
by Aswath Govindraju 05 Mar '22

05 Mar '22

Enable config for setting mmc speed mode from U-Boot command line. Signed-off-by: Aswath Govindraju <a-govindraju(a)ti.com> --- configs/j721e_evm_a72_defconfig | 1 + configs/j721e_hs_evm_a72_defconfig | 1 + 2 files changed, 2 insertions(+) diff --git a/configs/j721e_evm_a72_defconfig b/configs/j721e_evm_a72_defconfig index 8f412d65a8ac..c7a3f52762ec 100644 --- a/configs/j721e_evm_a72_defconfig +++ b/configs/j721e_evm_a72_defconfig @@ -190,3 +190,4 @@ CONFIG_UFS=y CONFIG_CADENCE_UFS=y CONFIG_TI_J721E_UFS=y CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_MMC_SPEED_MODE_SET=y diff --git a/configs/j721e_hs_evm_a72_defconfig b/configs/j721e_hs_evm_a72_defconfig index ae184b035878..6479f9baff0c 100644 --- a/configs/j721e_hs_evm_a72_defconfig +++ b/configs/j721e_hs_evm_a72_defconfig @@ -162,3 +162,4 @@ CONFIG_UFS=y CONFIG_CADENCE_UFS=y CONFIG_TI_J721E_UFS=y CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_MMC_SPEED_MODE_SET=y -- 2.17.1

2 1

[PATCH v2] arm: mach-k3: am6_init: Use CONFIG_TI_I2C_BOARD_DETECT
by Christian Gmeiner 05 Mar '22

05 Mar '22

We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT is set. Same as done for am64. This makes it possible to add a custom am65 based board design to U-Boot that does not use this board detection mechanism. Signed-off-by: Christian Gmeiner <christian.gmeiner(a)gmail.com> --- arch/arm/mach-k3/am6_init.c | 3 ++- board/ti/am65x/evm.c | 26 +++++++++++++++----------- 2 files changed, 17 insertions(+), 12 deletions(-) diff --git a/arch/arm/mach-k3/am6_init.c b/arch/arm/mach-k3/am6_init.c index ffb7aaded2..8a6b1de764 100644 --- a/arch/arm/mach-k3/am6_init.c +++ b/arch/arm/mach-k3/am6_init.c @@ -251,7 +251,8 @@ void board_init_f(ulong dummy) k3_sysfw_print_ver(); /* Perform EEPROM-based board detection */ - do_board_detect(); + if (IS_ENABLED(CONFIG_TI_I2C_BOARD_DETECT)) + do_board_detect(); #if defined(CONFIG_CPU_V7R) && defined(CONFIG_K3_AVS0) ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(k3_avs), diff --git a/board/ti/am65x/evm.c b/board/ti/am65x/evm.c index fbe33cbea5..7182a8cad1 100644 --- a/board/ti/am65x/evm.c +++ b/board/ti/am65x/evm.c @@ -129,6 +129,7 @@ int ft_board_setup(void *blob, struct bd_info *bd) } #endif +#ifdef CONFIG_TI_I2C_BOARD_DETECT int do_board_detect(void) { int ret; @@ -353,23 +354,26 @@ static int probe_daughtercards(void) return 0; } +#endif int board_late_init(void) { - struct ti_am6_eeprom *ep = TI_AM6_EEPROM_DATA; + if (IS_ENABLED(CONFIG_TI_I2C_BOARD_DETECT)) { + struct ti_am6_eeprom *ep = TI_AM6_EEPROM_DATA; - setup_board_eeprom_env(); + setup_board_eeprom_env(); - /* - * The first MAC address for ethernet a.k.a. ethernet0 comes from - * efuse populated via the am654 gigabit eth switch subsystem driver. - * All the other ones are populated via EEPROM, hence continue with - * an index of 1. - */ - board_ti_am6_set_ethaddr(1, ep->mac_addr_cnt); + /* + * The first MAC address for ethernet a.k.a. ethernet0 comes from + * efuse populated via the am654 gigabit eth switch subsystem driver. + * All the other ones are populated via EEPROM, hence continue with + * an index of 1. + */ + board_ti_am6_set_ethaddr(1, ep->mac_addr_cnt); - /* Check for and probe any plugged-in daughtercards */ - probe_daughtercards(); + /* Check for and probe any plugged-in daughtercards */ + probe_daughtercards(); + } return 0; } -- 2.34.1

2 3

[PATCH] configs: ti: use standard configuration nodes naming
by Romain Naour 05 Mar '22

05 Mar '22

Currently, any u-boot bootloader for ti armv7 platforms using DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1) doesn't boot when built with Yocto Poky (openembedded-core). ## Loading kernel from FIT Image at 90000000 ... Could not find configuration node ERROR: can't get kernel image! Arago forked the kernel-fitimage class [1] and altered the configuration nodes naming while adding the OPTEE support by using FITIMAGE_CONF_BY_NAME by default [2]. The "upstream" kernel-fitimage class from openembedded-core still add the "conf-" prefix for each configuration nodes [3]. The ITS file format (from doc/uImage.FIT/source_file_format.txt) is not really accurate with the expected naming of these nodes. But in practice the "conf-" prefix is widely used. When the FIT image support has been added for ti armv7 platforms the naming from Arago has been used [3]. Fix this issue by adding the prefix expected by the ITS file generated by kernel-fitimage class from openembedded-core. [1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h… [2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h… [3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fit… [3] 1e93cc8473e4fe018aececc8ed3bf8fc2b3ff561 Signed-off-by: Romain Naour <romain.naour(a)smile.fr> Cc: Tom Rini <trini(a)konsulko.com> --- include/configs/ti_armv7_common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h index 9733707009..7483bc821d 100644 --- a/include/configs/ti_armv7_common.h +++ b/include/configs/ti_armv7_common.h @@ -55,7 +55,7 @@ "do;" \ "setenv overlaystring ${overlaystring}'#'${overlay};" \ "done;\0" \ - "run_fit=bootm ${addr_fit}#${fdtfile}${overlaystring}\0" \ + "run_fit=bootm ${addr_fit}#conf-${fdtfile}${overlaystring}\0" \ /* * DDR information. If the CONFIG_NR_DRAM_BANKS is not defined, -- 2.34.1

3 3

[PATCH 1/9] Convert CONFIG_BIOSEMU to Kconfig
by Tom Rini 04 Mar '22

04 Mar '22

This converts the following to Kconfig: CONFIG_BIOSEMU Cc: Simon Glass <sjg(a)chromium.org> Signed-off-by: Tom Rini <trini(a)konsulko.com> --- board/google/Kconfig | 7 +++++++ include/configs/chromebook_samus.h | 3 --- include/configs/x86-chromebook.h | 1 - 3 files changed, 7 insertions(+), 4 deletions(-) diff --git a/board/google/Kconfig b/board/google/Kconfig index 22c4be392f7e..c57e518c33fe 100644 --- a/board/google/Kconfig +++ b/board/google/Kconfig @@ -4,12 +4,16 @@ if VENDOR_GOOGLE +config BIOSEMU + bool + choice prompt "Mainboard model" optional config TARGET_CHROMEBOOK_CORAL bool "Chromebook coral" + select BIOSEMU help This is a range of Intel-based laptops released in 2018. They use an Intel Apollo Lake SoC. The design supports WiFi, 4GB to 16GB of @@ -24,6 +28,7 @@ config TARGET_CHROMEBOOK_CORAL config TARGET_CHROMEBOOK_LINK bool "Chromebook link" + select BIOSEMU help This is the Chromebook Pixel released in 2013. It uses an Intel i5 Ivybridge which is a die-shrink of Sandybridge, with 4GB of @@ -36,6 +41,7 @@ config TARGET_CHROMEBOOK_LINK config TARGET_CHROMEBOOK_LINK64 bool "Chromebook link 64-bit" + select BIOSEMU help This is the Chromebook Pixel released in 2013. With this config U-Boot is built as a 64-bit binary. This allows testing while this @@ -43,6 +49,7 @@ config TARGET_CHROMEBOOK_LINK64 config TARGET_CHROMEBOX_PANTHER bool "Chromebox panther (not available)" + select BIOSEMU help Note: At present this must be used with coreboot. See README.x86 for instructions. diff --git a/include/configs/chromebook_samus.h b/include/configs/chromebook_samus.h index 9d5a63cabaab..e29be3fda4ac 100644 --- a/include/configs/chromebook_samus.h +++ b/include/configs/chromebook_samus.h @@ -15,9 +15,6 @@ #include <configs/x86-common.h> #include <configs/x86-chromebook.h> -/* We can rely on running natively, and this saves code size */ -#undef CONFIG_BIOSEMU - #undef CONFIG_STD_DEVICES_SETTINGS #define CONFIG_STD_DEVICES_SETTINGS "stdin=usbkbd,i8042-kbd,serial\0" \ "stdout=vidconsole,serial\0" \ diff --git a/include/configs/x86-chromebook.h b/include/configs/x86-chromebook.h index 0efc7156a6dd..b45d2bbd6266 100644 --- a/include/configs/x86-chromebook.h +++ b/include/configs/x86-chromebook.h @@ -24,7 +24,6 @@ #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS #define CONFIG_PCI_IO_SIZE 0xefff -#define CONFIG_BIOSEMU #define VIDEO_IO_OFFSET 0 #define CONFIG_X86EMU_RAW_IO -- 2.25.1

2 18

[PATCH 1/4] powerpc: Remove unused MPC8540/60ADS code
by Tom Rini 04 Mar '22

04 Mar '22

Remove some code, primarily CPM2 related, that is now unused since the removal of MPC8540/60ADS. Fixes 3913191c8a6b ("powerpc: mpc8540ads: mpc8560ads: Drop support for MPC8540/60ADS") Signed-off-by: Tom Rini <trini(a)konsulko.com> --- arch/powerpc/cpu/mpc85xx/Makefile | 2 - arch/powerpc/cpu/mpc85xx/commproc.c | 188 ------ arch/powerpc/cpu/mpc85xx/cpu.c | 4 - arch/powerpc/cpu/mpc85xx/cpu_init.c | 72 --- arch/powerpc/cpu/mpc85xx/fdt.c | 8 - arch/powerpc/cpu/mpc85xx/serial_scc.c | 262 -------- arch/powerpc/cpu/mpc85xx/speed.c | 16 - arch/powerpc/include/asm/cpm_85xx.h | 824 ------------------------- arch/powerpc/include/asm/global_data.h | 11 - arch/powerpc/include/asm/immap_85xx.h | 327 ---------- arch/powerpc/lib/bdinfo.c | 13 - arch/powerpc/lib/bootm.c | 6 - drivers/pci/pci_mpc85xx.c | 1 - include/asm-generic/u-boot.h | 6 - include/configs/MPC8540ADS.h | 303 --------- include/configs/MPC8560ADS.h | 292 --------- 16 files changed, 2335 deletions(-) delete mode 100644 arch/powerpc/cpu/mpc85xx/commproc.c delete mode 100644 arch/powerpc/cpu/mpc85xx/serial_scc.c delete mode 100644 arch/powerpc/include/asm/cpm_85xx.h delete mode 100644 include/configs/MPC8540ADS.h delete mode 100644 include/configs/MPC8560ADS.h diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile index 6f4ad1f9b762..c32cde04e16a 100644 --- a/arch/powerpc/cpu/mpc85xx/Makefile +++ b/arch/powerpc/cpu/mpc85xx/Makefile @@ -27,7 +27,6 @@ obj-$(CONFIG_MP) += release.o ifndef CONFIG_SPL_BUILD obj-$(CONFIG_CMD_ERRATA) += cmd_errata.o endif -obj-$(CONFIG_CPM2) += commproc.o obj-$(CONFIG_OF_LIBFDT) += fdt.o obj-$(CONFIG_FSL_CORENET) += liodn.o @@ -49,7 +48,6 @@ obj-$(CONFIG_ARCH_T2080) += t2080_ids.o obj-$(CONFIG_QE) += qe_io.o -obj-$(CONFIG_CPM2) += serial_scc.o obj-$(CONFIG_SYS_FSL_QORIQ_CHASSIS1) += fsl_corenet_serdes.o obj-$(CONFIG_SYS_FSL_QORIQ_CHASSIS2) += fsl_corenet2_serdes.o diff --git a/arch/powerpc/cpu/mpc85xx/commproc.c b/arch/powerpc/cpu/mpc85xx/commproc.c deleted file mode 100644 index 8e8427a08bbe..000000000000 --- a/arch/powerpc/cpu/mpc85xx/commproc.c +++ /dev/null @@ -1,188 +0,0 @@ -/* - * Adapted for Motorola MPC8560 chips - * Xianghua Xiao <x.xiao(a)motorola.com> - * - * This file is based on "arch/powerpc/8260_io/commproc.c" - here is it's - * copyright notice: - * - * General Purpose functions for the global management of the - * 8220 Communication Processor Module. - * Copyright (c) 1999 Dan Malek (dmalek(a)jlc.net) - * Copyright (c) 2000 MontaVista Software, Inc (source(a)mvista.com) - * 2.3.99 Updates - * Copyright (c) 2003 Motorola,Inc. - * - * In addition to the individual control of the communication - * channels, there are a few functions that globally affect the - * communication processor. - * - * Buffer descriptors must be allocated from the dual ported memory - * space. The allocator for that is here. When the communication - * process is reset, we reclaim the memory available. There is - * currently no deallocator for this memory. - */ -#include <common.h> -#include <asm-offsets.h> -#include <asm/cpm_85xx.h> -#include <asm/global_data.h> - -DECLARE_GLOBAL_DATA_PTR; - -/* - * because we have stack and init data in dual port ram - * we must reduce the size - */ -#undef CPM_DATAONLY_SIZE -#define CPM_DATAONLY_SIZE ((uint)(8 * 1024) - CPM_DATAONLY_BASE) - -void -m8560_cpm_reset(void) -{ - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - volatile ulong count; - - gd = (gd_t *) (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET); - - /* Reclaim the DP memory for our use. - */ - gd->arch.dp_alloc_base = CPM_DATAONLY_BASE; - gd->arch.dp_alloc_top = gd->arch.dp_alloc_base + CPM_DATAONLY_SIZE; - - /* - * Reset CPM - */ - cpm->im_cpm_cp.cpcr = CPM_CR_RST; - count = 0; - do { /* Spin until command processed */ - __asm__ __volatile__ ("eieio"); - } while ((cpm->im_cpm_cp.cpcr & CPM_CR_FLG) && ++count < 1000000); -} - -/* Allocate some memory from the dual ported ram. - * To help protocols with object alignment restrictions, we do that - * if they ask. - */ -uint -m8560_cpm_dpalloc(uint size, uint align) -{ - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - uint retloc; - uint align_mask, off; - uint savebase; - - align_mask = align - 1; - savebase = gd->arch.dp_alloc_base; - - off = gd->arch.dp_alloc_base & align_mask; - if (off != 0) - gd->arch.dp_alloc_base += (align - off); - - if ((off = size & align_mask) != 0) - size += align - off; - - if ((gd->arch.dp_alloc_base + size) >= gd->arch.dp_alloc_top) { - gd->arch.dp_alloc_base = savebase; - panic("m8560_cpm_dpalloc: ran out of dual port ram!"); - } - - retloc = gd->arch.dp_alloc_base; - gd->arch.dp_alloc_base += size; - - memset((void *)&(cpm->im_dprambase[retloc]), 0, size); - - return(retloc); -} - -/* We also own one page of host buffer space for the allocation of - * UART "fifos" and the like. - */ -uint -m8560_cpm_hostalloc(uint size, uint align) -{ - /* the host might not even have RAM yet - just use dual port RAM */ - return (m8560_cpm_dpalloc(size, align)); -} - -/* Set a baud rate generator. This needs lots of work. There are - * eight BRGs, which can be connected to the CPM channels or output - * as clocks. The BRGs are in two different block of internal - * memory mapped space. - * The baud rate clock is the system clock divided by something. - * It was set up long ago during the initial boot phase and is - * is given to us. - * Baud rate clocks are zero-based in the driver code (as that maps - * to port numbers). Documentation uses 1-based numbering. - */ -#define BRG_INT_CLK gd->arch.brg_clk -#define BRG_UART_CLK ((BRG_INT_CLK + 15) / 16) - -/* This function is used by UARTS, or anything else that uses a 16x - * oversampled clock. - */ -void -m8560_cpm_setbrg(uint brg, uint rate) -{ - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - volatile uint *bp; - - /* This is good enough to get SMCs running..... - */ - if (brg < 4) { - bp = (uint *)&(cpm->im_cpm_brg1.brgc1); - } - else { - bp = (uint *)&(cpm->im_cpm_brg2.brgc5); - brg -= 4; - } - bp += brg; - *bp = (((((BRG_UART_CLK+rate-1)/rate)-1)&0xfff)<<1)|CPM_BRG_EN; -} - -/* This function is used to set high speed synchronous baud rate - * clocks. - */ -void -m8560_cpm_fastbrg(uint brg, uint rate, int div16) -{ - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - volatile uint *bp; - - /* This is good enough to get SMCs running..... - */ - if (brg < 4) { - bp = (uint *)&(cpm->im_cpm_brg1.brgc1); - } - else { - bp = (uint *)&(cpm->im_cpm_brg2.brgc5); - brg -= 4; - } - bp += brg; - *bp = (((((BRG_INT_CLK+rate-1)/rate)-1)&0xfff)<<1)|CPM_BRG_EN; - if (div16) - *bp |= CPM_BRG_DIV16; -} - -/* This function is used to set baud rate generators using an external - * clock source and 16x oversampling. - */ - -void -m8560_cpm_extcbrg(uint brg, uint rate, uint extclk, int pinsel) -{ - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - volatile uint *bp; - - if (brg < 4) { - bp = (uint *)&(cpm->im_cpm_brg1.brgc1); - } - else { - bp = (uint *)&(cpm->im_cpm_brg2.brgc5); - brg -= 4; - } - bp += brg; - *bp = ((((((extclk/16)+rate-1)/rate)-1)&0xfff)<<1)|CPM_BRG_EN; - if (pinsel == 0) - *bp |= CPM_BRG_EXTC_CLK3_9; - else - *bp |= CPM_BRG_EXTC_CLK5_15; -} diff --git a/arch/powerpc/cpu/mpc85xx/cpu.c b/arch/powerpc/cpu/mpc85xx/cpu.c index cd32290410f6..cc1d02df8115 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu.c +++ b/arch/powerpc/cpu/mpc85xx/cpu.c @@ -241,10 +241,6 @@ int checkcpu (void) printf("IFC:%-4s MHz\n", strmhz(buf1, sysinfo.freq_localbus)); #endif -#ifdef CONFIG_CPM2 - printf("CPM: %s MHz\n", strmhz(buf1, sysinfo.freq_systembus)); -#endif - #ifdef CONFIG_QE printf(" QE:%-4s MHz\n", strmhz(buf1, sysinfo.freq_qe)); #endif diff --git a/arch/powerpc/cpu/mpc85xx/cpu_init.c b/arch/powerpc/cpu/mpc85xx/cpu_init.c index e920e01b254f..e9e133baf070 100644 --- a/arch/powerpc/cpu/mpc85xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc85xx/cpu_init.c @@ -152,70 +152,6 @@ static void config_qe_ioports(void) } #endif -#ifdef CONFIG_CPM2 -void config_8560_ioports (volatile ccsr_cpm_t * cpm) -{ - int portnum; - - for (portnum = 0; portnum < 4; portnum++) { - uint pmsk = 0, - ppar = 0, - psor = 0, - pdir = 0, - podr = 0, - pdat = 0; - iop_conf_t *iopc = (iop_conf_t *) & iop_conf_tab[portnum][0]; - iop_conf_t *eiopc = iopc + 32; - uint msk = 1; - - /* - * NOTE: - * index 0 refers to pin 31, - * index 31 refers to pin 0 - */ - while (iopc < eiopc) { - if (iopc->conf) { - pmsk |= msk; - if (iopc->ppar) - ppar |= msk; - if (iopc->psor) - psor |= msk; - if (iopc->pdir) - pdir |= msk; - if (iopc->podr) - podr |= msk; - if (iopc->pdat) - pdat |= msk; - } - - msk <<= 1; - iopc++; - } - - if (pmsk != 0) { - volatile ioport_t *iop = ioport_addr (cpm, portnum); - uint tpmsk = ~pmsk; - - /* - * the (somewhat confused) paragraph at the - * bottom of page 35-5 warns that there might - * be "unknown behaviour" when programming - * PSORx and PDIRx, if PPARx = 1, so I - * decided this meant I had to disable the - * dedicated function first, and enable it - * last. - */ - iop->ppar &= tpmsk; - iop->psor = (iop->psor & tpmsk) | psor; - iop->podr = (iop->podr & tpmsk) | podr; - iop->pdat = (iop->pdat & tpmsk) | pdat; - iop->pdir = (iop->pdir & tpmsk) | pdir; - iop->ppar |= ppar; - } - } -} -#endif - #ifdef CONFIG_SYS_FSL_CPC #if defined(CONFIG_RAMBOOT_PBL) || defined(CONFIG_SYS_CPC_REINIT_F) void disable_cpc_sram(void) @@ -474,16 +410,8 @@ ulong cpu_init_f(void) #endif #endif -#ifdef CONFIG_CPM2 - config_8560_ioports((ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR); -#endif - init_early_memctl_regs(); -#if defined(CONFIG_CPM2) - m8560_cpm_reset(); -#endif - #if defined(CONFIG_QE) && !defined(CONFIG_U_QE) /* Config QE ioports */ config_qe_ioports(); diff --git a/arch/powerpc/cpu/mpc85xx/fdt.c b/arch/powerpc/cpu/mpc85xx/fdt.c index d4b828e3824c..c8ad6a1b01ce 100644 --- a/arch/powerpc/cpu/mpc85xx/fdt.c +++ b/arch/powerpc/cpu/mpc85xx/fdt.c @@ -652,14 +652,6 @@ void ft_cpu_setup(void *blob, struct bd_info *bd) "clock-frequency", CONFIG_SYS_NS16550_CLK, 1); #endif -#ifdef CONFIG_CPM2 - do_fixup_by_compat_u32(blob, "fsl,cpm2-scc-uart", - "current-speed", gd->baudrate, 1); - - do_fixup_by_compat_u32(blob, "fsl,cpm2-brg", - "clock-frequency", bd->bi_brgfreq, 1); -#endif - #ifdef CONFIG_FSL_CORENET do_fixup_by_compat_u32(blob, "fsl,qoriq-clockgen-1.0", "clock-frequency", get_board_sys_clk(), 1); diff --git a/arch/powerpc/cpu/mpc85xx/serial_scc.c b/arch/powerpc/cpu/mpc85xx/serial_scc.c deleted file mode 100644 index a2505d1ffc1d..000000000000 --- a/arch/powerpc/cpu/mpc85xx/serial_scc.c +++ /dev/null @@ -1,262 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * (C) Copyright 2003 Motorola Inc. - * Xianghua Xiao (X.Xiao(a)motorola.com) - * Modified based on 8260 for 8560. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd(a)denx.de. - * - * Hacked for MPC8260 by Murray.Jensen(a)cmst.csiro.au, 19-Oct-00. - */ - -/* - * Minimal serial functions needed to use one of the SCC ports - * as serial console interface. - */ - -#include <common.h> -#include <asm/cpm_85xx.h> -#include <serial.h> -#include <asm/global_data.h> -#include <linux/compiler.h> - -DECLARE_GLOBAL_DATA_PTR; - -#if defined(CONFIG_CONS_ON_SCC) - -#if CONFIG_CONS_INDEX == 1 /* Console on SCC1 */ - -#define SCC_INDEX 0 -#define PROFF_SCC PROFF_SCC1 -#define CMXSCR_MASK (CMXSCR_GR1|CMXSCR_SC1|\ - CMXSCR_RS1CS_MSK|CMXSCR_TS1CS_MSK) -#define CMXSCR_VALUE (CMXSCR_RS1CS_BRG1|CMXSCR_TS1CS_BRG1) -#define CPM_CR_SCC_PAGE CPM_CR_SCC1_PAGE -#define CPM_CR_SCC_SBLOCK CPM_CR_SCC1_SBLOCK - -#elif CONFIG_CONS_INDEX == 2 /* Console on SCC2 */ - -#define SCC_INDEX 1 -#define PROFF_SCC PROFF_SCC2 -#define CMXSCR_MASK (CMXSCR_GR2|CMXSCR_SC2|\ - CMXSCR_RS2CS_MSK|CMXSCR_TS2CS_MSK) -#define CMXSCR_VALUE (CMXSCR_RS2CS_BRG2|CMXSCR_TS2CS_BRG2) -#define CPM_CR_SCC_PAGE CPM_CR_SCC2_PAGE -#define CPM_CR_SCC_SBLOCK CPM_CR_SCC2_SBLOCK - -#elif CONFIG_CONS_INDEX == 3 /* Console on SCC3 */ - -#define SCC_INDEX 2 -#define PROFF_SCC PROFF_SCC3 -#define CMXSCR_MASK (CMXSCR_GR3|CMXSCR_SC3|\ - CMXSCR_RS3CS_MSK|CMXSCR_TS3CS_MSK) -#define CMXSCR_VALUE (CMXSCR_RS3CS_BRG3|CMXSCR_TS3CS_BRG3) -#define CPM_CR_SCC_PAGE CPM_CR_SCC3_PAGE -#define CPM_CR_SCC_SBLOCK CPM_CR_SCC3_SBLOCK - -#elif CONFIG_CONS_INDEX == 4 /* Console on SCC4 */ - -#define SCC_INDEX 3 -#define PROFF_SCC PROFF_SCC4 -#define CMXSCR_MASK (CMXSCR_GR4|CMXSCR_SC4|\ - CMXSCR_RS4CS_MSK|CMXSCR_TS4CS_MSK) -#define CMXSCR_VALUE (CMXSCR_RS4CS_BRG4|CMXSCR_TS4CS_BRG4) -#define CPM_CR_SCC_PAGE CPM_CR_SCC4_PAGE -#define CPM_CR_SCC_SBLOCK CPM_CR_SCC4_SBLOCK - -#else - -#error "console not correctly defined" - -#endif - -static int mpc85xx_serial_init(void) -{ - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - volatile ccsr_cpm_scc_t *sp; - volatile scc_uart_t *up; - volatile cbd_t *tbdf, *rbdf; - volatile ccsr_cpm_cp_t *cp = &(cpm->im_cpm_cp); - uint dpaddr; - - /* initialize pointers to SCC */ - - sp = (ccsr_cpm_scc_t *) &(cpm->im_cpm_scc[SCC_INDEX]); - up = (scc_uart_t *)&(cpm->im_dprambase[PROFF_SCC]); - - /* Disable transmitter/receiver. - */ - sp->gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT); - - /* put the SCC channel into NMSI (non multiplexd serial interface) - * mode and wire the selected SCC Tx and Rx clocks to BRGx (15-15). - */ - cpm->im_cpm_mux.cmxscr = \ - (cpm->im_cpm_mux.cmxscr&~CMXSCR_MASK)|CMXSCR_VALUE; - - /* Set up the baud rate generator. - */ - serial_setbrg (); - - /* Allocate space for two buffer descriptors in the DP ram. - * damm: allocating space after the two buffers for rx/tx data - */ - - dpaddr = m8560_cpm_dpalloc((2 * sizeof (cbd_t)) + 2, 16); - - /* Set the physical address of the host memory buffers in - * the buffer descriptors. - */ - rbdf = (cbd_t *)&(cpm->im_dprambase[dpaddr]); - rbdf->cbd_bufaddr = (uint) (rbdf+2); - rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP; - tbdf = rbdf + 1; - tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1; - tbdf->cbd_sc = BD_SC_WRAP; - - /* Set up the uart parameters in the parameter ram. - */ - up->scc_genscc.scc_rbase = dpaddr; - up->scc_genscc.scc_tbase = dpaddr+sizeof(cbd_t); - up->scc_genscc.scc_rfcr = CPMFCR_EB; - up->scc_genscc.scc_tfcr = CPMFCR_EB; - up->scc_genscc.scc_mrblr = 1; - up->scc_maxidl = 0; - up->scc_brkcr = 1; - up->scc_parec = 0; - up->scc_frmec = 0; - up->scc_nosec = 0; - up->scc_brkec = 0; - up->scc_uaddr1 = 0; - up->scc_uaddr2 = 0; - up->scc_toseq = 0; - up->scc_char1 = up->scc_char2 = up->scc_char3 = up->scc_char4 = 0x8000; - up->scc_char5 = up->scc_char6 = up->scc_char7 = up->scc_char8 = 0x8000; - up->scc_rccm = 0xc0ff; - - /* Mask all interrupts and remove anything pending. - */ - sp->sccm = 0; - sp->scce = 0xffff; - - /* Set 8 bit FIFO, 16 bit oversampling and UART mode. - */ - sp->gsmrh = SCC_GSMRH_RFW; /* 8 bit FIFO */ - sp->gsmrl = \ - SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16 | SCC_GSMRL_MODE_UART; - - /* Set CTS no flow control, 1 stop bit, 8 bit character length, - * normal async UART mode, no parity - */ - sp->psmr = SCU_PSMR_CL; - - /* execute the "Init Rx and Tx params" CP command. - */ - - while (cp->cpcr & CPM_CR_FLG) /* wait if cp is busy */ - ; - - cp->cpcr = mk_cr_cmd(CPM_CR_SCC_PAGE, CPM_CR_SCC_SBLOCK, - 0, CPM_CR_INIT_TRX) | CPM_CR_FLG; - - while (cp->cpcr & CPM_CR_FLG) /* wait if cp is busy */ - ; - - /* Enable transmitter/receiver. - */ - sp->gsmrl |= SCC_GSMRL_ENR | SCC_GSMRL_ENT; - - return (0); -} - -static void mpc85xx_serial_setbrg(void) -{ -#if defined(CONFIG_CONS_USE_EXTC) - m8560_cpm_extcbrg(SCC_INDEX, gd->baudrate, - CONFIG_CONS_EXTC_RATE, CONFIG_CONS_EXTC_PINSEL); -#else - m8560_cpm_setbrg(SCC_INDEX, gd->baudrate); -#endif -} - -static void mpc85xx_serial_putc(const char c) -{ - volatile scc_uart_t *up; - volatile cbd_t *tbdf; - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - - if (c == '\n') - serial_putc ('\r'); - - up = (scc_uart_t *)&(cpm->im_dprambase[PROFF_SCC]); - tbdf = (cbd_t *)&(cpm->im_dprambase[up->scc_genscc.scc_tbase]); - - /* Wait for last character to go. - */ - while (tbdf->cbd_sc & BD_SC_READY) - ; - - /* Load the character into the transmit buffer. - */ - *(volatile char *)tbdf->cbd_bufaddr = c; - tbdf->cbd_datlen = 1; - tbdf->cbd_sc |= BD_SC_READY; -} - -static int mpc85xx_serial_getc(void) -{ - volatile cbd_t *rbdf; - volatile scc_uart_t *up; - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - unsigned char c; - - up = (scc_uart_t *)&(cpm->im_dprambase[PROFF_SCC]); - rbdf = (cbd_t *)&(cpm->im_dprambase[up->scc_genscc.scc_rbase]); - - /* Wait for character to show up. - */ - while (rbdf->cbd_sc & BD_SC_EMPTY) - ; - - /* Grab the char and clear the buffer again. - */ - c = *(volatile unsigned char *)rbdf->cbd_bufaddr; - rbdf->cbd_sc |= BD_SC_EMPTY; - - return (c); -} - -static int mpc85xx_serial_tstc(void) -{ - volatile cbd_t *rbdf; - volatile scc_uart_t *up; - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - - up = (scc_uart_t *)&(cpm->im_dprambase[PROFF_SCC]); - rbdf = (cbd_t *)&(cpm->im_dprambase[up->scc_genscc.scc_rbase]); - - return ((rbdf->cbd_sc & BD_SC_EMPTY) == 0); -} - -static struct serial_device mpc85xx_serial_drv = { - .name = "mpc85xx_serial", - .start = mpc85xx_serial_init, - .stop = NULL, - .setbrg = mpc85xx_serial_setbrg, - .putc = mpc85xx_serial_putc, - .puts = default_serial_puts, - .getc = mpc85xx_serial_getc, - .tstc = mpc85xx_serial_tstc, -}; - -void mpc85xx_serial_initialize(void) -{ - serial_register(&mpc85xx_serial_drv); -} - -__weak struct serial_device *default_serial_console(void) -{ - return &mpc85xx_serial_drv; -} -#endif /* CONFIG_CONS_ON_SCC */ diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c index 5a9cd281617b..4b6f3d28baa6 100644 --- a/arch/powerpc/cpu/mpc85xx/speed.c +++ b/arch/powerpc/cpu/mpc85xx/speed.c @@ -580,15 +580,6 @@ int get_clocks(void) sys_info_t sys_info; #ifdef CONFIG_ARCH_MPC8544 volatile ccsr_gur_t *gur = (void *) CONFIG_SYS_MPC85xx_GUTS_ADDR; -#endif -#if defined(CONFIG_CPM2) - volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR; - uint sccr, dfbrg; - - /* set VCO = 4 * BRG */ - cpm->im_cpm_intctl.sccr &= 0xfffffffc; - sccr = cpm->im_cpm_intctl.sccr; - dfbrg = (sccr & SCCR_DFBRG_MSK) >> SCCR_DFBRG_SHIFT; #endif get_sys_info (&sys_info); gd->cpu_clk = sys_info.freq_processor[0]; @@ -635,13 +626,6 @@ int get_clocks(void) #endif #endif /* defined(CONFIG_FSL_ESDHC) */ -#if defined(CONFIG_CPM2) - gd->arch.vco_out = 2*sys_info.freq_systembus; - gd->arch.cpm_clk = gd->arch.vco_out / 2; - gd->arch.scc_clk = gd->arch.vco_out / 4; - gd->arch.brg_clk = gd->arch.vco_out / (1 << (2 * (dfbrg + 1))); -#endif - if(gd->cpu_clk != 0) return (0); else return (1); } diff --git a/arch/powerpc/include/asm/cpm_85xx.h b/arch/powerpc/include/asm/cpm_85xx.h deleted file mode 100644 index d42469c6e056..000000000000 --- a/arch/powerpc/include/asm/cpm_85xx.h +++ /dev/null @@ -1,824 +0,0 @@ -/* - * MPC85xx Communication Processor Module - * Copyright (c) 2003,Motorola Inc. - * Xianghua Xiao (X.Xiao(a)motorola.com) - * - * MPC8260 Communication Processor Module. - * Copyright (c) 1999 Dan Malek (dmalek(a)jlc.net) - * - * This file contains structures and information for the communication - * processor channels found in the dual port RAM or parameter RAM. - * All CPM control and status is available through the MPC8260 internal - * memory map. See immap.h for details. - */ -#ifndef __CPM_85XX__ -#define __CPM_85XX__ - -#include <asm/immap_85xx.h> - -/* CPM Command register. -*/ -#define CPM_CR_RST ((uint)0x80000000) -#define CPM_CR_PAGE ((uint)0x7c000000) -#define CPM_CR_SBLOCK ((uint)0x03e00000) -#define CPM_CR_FLG ((uint)0x00010000) -#define CPM_CR_MCN ((uint)0x00003fc0) -#define CPM_CR_OPCODE ((uint)0x0000000f) - -/* Device sub-block and page codes. -*/ -#define CPM_CR_SCC1_SBLOCK (0x04) -#define CPM_CR_SCC2_SBLOCK (0x05) -#define CPM_CR_SCC3_SBLOCK (0x06) -#define CPM_CR_SCC4_SBLOCK (0x07) -#define CPM_CR_SMC1_SBLOCK (0x08) -#define CPM_CR_SMC2_SBLOCK (0x09) -#define CPM_CR_SPI_SBLOCK (0x0a) -#define CPM_CR_I2C_SBLOCK (0x0b) -#define CPM_CR_TIMER_SBLOCK (0x0f) -#define CPM_CR_RAND_SBLOCK (0x0e) -#define CPM_CR_FCC1_SBLOCK (0x10) -#define CPM_CR_FCC2_SBLOCK (0x11) -#define CPM_CR_FCC3_SBLOCK (0x12) -#define CPM_CR_MCC1_SBLOCK (0x1c) - -#define CPM_CR_SCC1_PAGE (0x00) -#define CPM_CR_SCC2_PAGE (0x01) -#define CPM_CR_SCC3_PAGE (0x02) -#define CPM_CR_SCC4_PAGE (0x03) -#define CPM_CR_SPI_PAGE (0x09) -#define CPM_CR_I2C_PAGE (0x0a) -#define CPM_CR_TIMER_PAGE (0x0a) -#define CPM_CR_RAND_PAGE (0x0a) -#define CPM_CR_FCC1_PAGE (0x04) -#define CPM_CR_FCC2_PAGE (0x05) -#define CPM_CR_FCC3_PAGE (0x06) -#define CPM_CR_MCC1_PAGE (0x07) -#define CPM_CR_MCC2_PAGE (0x08) - -/* Some opcodes (there are more...later) -*/ -#define CPM_CR_INIT_TRX ((ushort)0x0000) -#define CPM_CR_INIT_RX ((ushort)0x0001) -#define CPM_CR_INIT_TX ((ushort)0x0002) -#define CPM_CR_HUNT_MODE ((ushort)0x0003) -#define CPM_CR_STOP_TX ((ushort)0x0004) -#define CPM_CR_RESTART_TX ((ushort)0x0006) -#define CPM_CR_SET_GADDR ((ushort)0x0008) - -#define mk_cr_cmd(PG, SBC, MCN, OP) \ - ((PG << 26) | (SBC << 21) | (MCN << 6) | OP) - -/* Dual Port RAM addresses. The first 16K is available for almost - * any CPM use, so we put the BDs there. The first 128 bytes are - * used for SMC1 and SMC2 parameter RAM, so we start allocating - * BDs above that. All of this must change when we start - * downloading RAM microcode. - */ -#define CPM_DATAONLY_BASE ((uint)128) -#define CPM_DP_NOSPACE ((uint)0x7FFFFFFF) -#define CPM_FCC_SPECIAL_BASE ((uint)0x0000B000) -#define CPM_DATAONLY_SIZE ((uint)(16 * 1024) - CPM_DATAONLY_BASE) - -/* The number of pages of host memory we allocate for CPM. This is - * done early in kernel initialization to get physically contiguous - * pages. - */ -#define NUM_CPM_HOST_PAGES 2 - -/* Export the base address of the communication processor registers - * and dual port ram. - */ -/*extern cpm8560_t *cpmp; Pointer to comm processor */ -uint m8560_cpm_dpalloc(uint size, uint align); -uint m8560_cpm_hostalloc(uint size, uint align); -void m8560_cpm_setbrg(uint brg, uint rate); -void m8560_cpm_fastbrg(uint brg, uint rate, int div16); -void m8560_cpm_extcbrg(uint brg, uint rate, uint extclk, int pinsel); - -/* Buffer descriptors used by many of the CPM protocols. -*/ -typedef struct cpm_buf_desc { - ushort cbd_sc; /* Status and Control */ - ushort cbd_datlen; /* Data length in buffer */ - uint cbd_bufaddr; /* Buffer address in host memory */ -} cbd_t; - -#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */ -#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */ -#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */ -#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */ -#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */ -#define BD_SC_CM ((ushort)0x0200) /* Continous mode */ -#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */ -#define BD_SC_P ((ushort)0x0100) /* xmt preamble */ -#define BD_SC_BR ((ushort)0x0020) /* Break received */ -#define BD_SC_FR ((ushort)0x0010) /* Framing error */ -#define BD_SC_PR ((ushort)0x0008) /* Parity error */ -#define BD_SC_OV ((ushort)0x0002) /* Overrun */ -#define BD_SC_CD ((ushort)0x0001) /* ?? */ - -/* Function code bits, usually generic to devices. -*/ -#define CPMFCR_GBL ((u_char)0x20) /* Set memory snooping */ -#define CPMFCR_EB ((u_char)0x10) /* Set big endian byte order */ -#define CPMFCR_TC2 ((u_char)0x04) /* Transfer code 2 value */ -#define CPMFCR_DTB ((u_char)0x02) /* Use local bus for data when set */ -#define CPMFCR_BDB ((u_char)0x01) /* Use local bus for BD when set */ - -/* Parameter RAM offsets from the base. -*/ -#define CPM_POST_WORD_ADDR 0x80FC /* steal a long at the end of SCC1 */ -#define PROFF_SCC1 ((uint)0x8000) -#define PROFF_SCC2 ((uint)0x8100) -#define PROFF_SCC3 ((uint)0x8200) -#define PROFF_SCC4 ((uint)0x8300) -#define PROFF_FCC1 ((uint)0x8400) -#define PROFF_FCC2 ((uint)0x8500) -#define PROFF_FCC3 ((uint)0x8600) -#define PROFF_MCC1 ((uint)0x8700) -#define PROFF_MCC2 ((uint)0x8800) -#define PROFF_SPI_BASE ((uint)0x89fc) -#define PROFF_TIMERS ((uint)0x8ae0) -#define PROFF_REVNUM ((uint)0x8af0) -#define PROFF_RAND ((uint)0x8af8) -#define PROFF_I2C_BASE ((uint)0x8afc) - -/* Baud rate generators. -*/ -#define CPM_BRG_RST ((uint)0x00020000) -#define CPM_BRG_EN ((uint)0x00010000) -#define CPM_BRG_EXTC_INT ((uint)0x00000000) -#define CPM_BRG_EXTC_CLK3_9 ((uint)0x00004000) -#define CPM_BRG_EXTC_CLK5_15 ((uint)0x00008000) -#define CPM_BRG_ATB ((uint)0x00002000) -#define CPM_BRG_CD_MASK ((uint)0x00001ffe) -#define CPM_BRG_DIV16 ((uint)0x00000001) - -/* SCCs. -*/ -#define SCC_GSMRH_IRP ((uint)0x00040000) -#define SCC_GSMRH_GDE ((uint)0x00010000) -#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000) -#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000) -#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000) -#define SCC_GSMRH_REVD ((uint)0x00002000) -#define SCC_GSMRH_TRX ((uint)0x00001000) -#define SCC_GSMRH_TTX ((uint)0x00000800) -#define SCC_GSMRH_CDP ((uint)0x00000400) -#define SCC_GSMRH_CTSP ((uint)0x00000200) -#define SCC_GSMRH_CDS ((uint)0x00000100) -#define SCC_GSMRH_CTSS ((uint)0x00000080) -#define SCC_GSMRH_TFL ((uint)0x00000040) -#define SCC_GSMRH_RFW ((uint)0x00000020) -#define SCC_GSMRH_TXSY ((uint)0x00000010) -#define SCC_GSMRH_SYNL16 ((uint)0x0000000c) -#define SCC_GSMRH_SYNL8 ((uint)0x00000008) -#define SCC_GSMRH_SYNL4 ((uint)0x00000004) -#define SCC_GSMRH_RTSM ((uint)0x00000002) -#define SCC_GSMRH_RSYN ((uint)0x00000001) - -#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */ -#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000) -#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000) -#define SCC_GSMRL_EDGE_POS ((uint)0x20000000) -#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000) -#define SCC_GSMRL_TCI ((uint)0x10000000) -#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000) -#define SCC_GSMRL_TSNC_4 ((uint)0x08000000) -#define SCC_GSMRL_TSNC_14 ((uint)0x04000000) -#define SCC_GSMRL_TSNC_INF ((uint)0x00000000) -#define SCC_GSMRL_RINV ((uint)0x02000000) -#define SCC_GSMRL_TINV ((uint)0x01000000) -#define SCC_GSMRL_TPL_128 ((uint)0x00c00000) -#define SCC_GSMRL_TPL_64 ((uint)0x00a00000) -#define SCC_GSMRL_TPL_48 ((uint)0x00800000) -#define SCC_GSMRL_TPL_32 ((uint)0x00600000) -#define SCC_GSMRL_TPL_16 ((uint)0x00400000) -#define SCC_GSMRL_TPL_8 ((uint)0x00200000) -#define SCC_GSMRL_TPL_NONE ((uint)0x00000000) -#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000) -#define SCC_GSMRL_TPP_01 ((uint)0x00100000) -#define SCC_GSMRL_TPP_10 ((uint)0x00080000) -#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000) -#define SCC_GSMRL_TEND ((uint)0x00040000) -#define SCC_GSMRL_TDCR_32 ((uint)0x00030000) -#define SCC_GSMRL_TDCR_16 ((uint)0x00020000) -#define SCC_GSMRL_TDCR_8 ((uint)0x00010000) -#define SCC_GSMRL_TDCR_1 ((uint)0x00000000) -#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000) -#define SCC_GSMRL_RDCR_16 ((uint)0x00008000) -#define SCC_GSMRL_RDCR_8 ((uint)0x00004000) -#define SCC_GSMRL_RDCR_1 ((uint)0x00000000) -#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000) -#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000) -#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000) -#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800) -#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000) -#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600) -#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400) -#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200) -#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100) -#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000) -#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */ -#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080) -#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040) -#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000) -#define SCC_GSMRL_ENR ((uint)0x00000020) -#define SCC_GSMRL_ENT ((uint)0x00000010) -#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c) -#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009) -#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008) -#define SCC_GSMRL_MODE_V14 ((uint)0x00000007) -#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006) -#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005) -#define SCC_GSMRL_MODE_UART ((uint)0x00000004) -#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003) -#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002) -#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000) - -#define SCC_TODR_TOD ((ushort)0x8000) - -/* SCC Event and Mask register. -*/ -#define SCCM_TXE ((unsigned char)0x10) -#define SCCM_BSY ((unsigned char)0x04) -#define SCCM_TX ((unsigned char)0x02) -#define SCCM_RX ((unsigned char)0x01) - -typedef struct scc_param { - ushort scc_rbase; /* Rx Buffer descriptor base address */ - ushort scc_tbase; /* Tx Buffer descriptor base address */ - u_char scc_rfcr; /* Rx function code */ - u_char scc_tfcr; /* Tx function code */ - ushort scc_mrblr; /* Max receive buffer length */ - uint scc_rstate; /* Internal */ - uint scc_idp; /* Internal */ - ushort scc_rbptr; /* Internal */ - ushort scc_ibc; /* Internal */ - uint scc_rxtmp; /* Internal */ - uint scc_tstate; /* Internal */ - uint scc_tdp; /* Internal */ - ushort scc_tbptr; /* Internal */ - ushort scc_tbc; /* Internal */ - uint scc_txtmp; /* Internal */ - uint scc_rcrc; /* Internal */ - uint scc_tcrc; /* Internal */ -} sccp_t; - -/* CPM Ethernet through SCC1. - */ -typedef struct scc_enet { - sccp_t sen_genscc; - uint sen_cpres; /* Preset CRC */ - uint sen_cmask; /* Constant mask for CRC */ - uint sen_crcec; /* CRC Error counter */ - uint sen_alec; /* alignment error counter */ - uint sen_disfc; /* discard frame counter */ - ushort sen_pads; /* Tx short frame pad character */ - ushort sen_retlim; /* Retry limit threshold */ - ushort sen_retcnt; /* Retry limit counter */ - ushort sen_maxflr; /* maximum frame length register */ - ushort sen_minflr; /* minimum frame length register */ - ushort sen_maxd1; /* maximum DMA1 length */ - ushort sen_maxd2; /* maximum DMA2 length */ - ushort sen_maxd; /* Rx max DMA */ - ushort sen_dmacnt; /* Rx DMA counter */ - ushort sen_maxb; /* Max BD byte count */ - ushort sen_gaddr1; /* Group address filter */ - ushort sen_gaddr2; - ushort sen_gaddr3; - ushort sen_gaddr4; - uint sen_tbuf0data0; /* Save area 0 - current frame */ - uint sen_tbuf0data1; /* Save area 1 - current frame */ - uint sen_tbuf0rba; /* Internal */ - uint sen_tbuf0crc; /* Internal */ - ushort sen_tbuf0bcnt; /* Internal */ - ushort sen_paddrh; /* physical address (MSB) */ - ushort sen_paddrm; - ushort sen_paddrl; /* physical address (LSB) */ - ushort sen_pper; /* persistence */ - ushort sen_rfbdptr; /* Rx first BD pointer */ - ushort sen_tfbdptr; /* Tx first BD pointer */ - ushort sen_tlbdptr; /* Tx last BD pointer */ - uint sen_tbuf1data0; /* Save area 0 - current frame */ - uint sen_tbuf1data1; /* Save area 1 - current frame */ - uint sen_tbuf1rba; /* Internal */ - uint sen_tbuf1crc; /* Internal */ - ushort sen_tbuf1bcnt; /* Internal */ - ushort sen_txlen; /* Tx Frame length counter */ - ushort sen_iaddr1; /* Individual address filter */ - ushort sen_iaddr2; - ushort sen_iaddr3; - ushort sen_iaddr4; - ushort sen_boffcnt; /* Backoff counter */ - - /* NOTE: Some versions of the manual have the following items - * incorrectly documented. Below is the proper order. - */ - ushort sen_taddrh; /* temp address (MSB) */ - ushort sen_taddrm; - ushort sen_taddrl; /* temp address (LSB) */ -} scc_enet_t; - - -/* SCC Event register as used by Ethernet. -*/ -#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ -#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */ -#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */ -#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */ -#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ -#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */ - -/* SCC Mode Register (PSMR) as used by Ethernet. -*/ -#define SCC_PSMR_HBC ((ushort)0x8000) /* Enable heartbeat */ -#define SCC_PSMR_FC ((ushort)0x4000) /* Force collision */ -#define SCC_PSMR_RSH ((ushort)0x2000) /* Receive short frames */ -#define SCC_PSMR_IAM ((ushort)0x1000) /* Check individual hash */ -#define SCC_PSMR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */ -#define SCC_PSMR_PRO ((ushort)0x0200) /* Promiscuous mode */ -#define SCC_PSMR_BRO ((ushort)0x0100) /* Catch broadcast pkts */ -#define SCC_PSMR_SBT ((ushort)0x0080) /* Special backoff timer */ -#define SCC_PSMR_LPB ((ushort)0x0040) /* Set Loopback mode */ -#define SCC_PSMR_SIP ((ushort)0x0020) /* Sample Input Pins */ -#define SCC_PSMR_LCW ((ushort)0x0010) /* Late collision window */ -#define SCC_PSMR_NIB22 ((ushort)0x000a) /* Start frame search */ -#define SCC_PSMR_FDE ((ushort)0x0001) /* Full duplex enable */ - -/* Buffer descriptor control/status used by Ethernet receive. - * Common to SCC and FCC. - */ -#define BD_ENET_RX_EMPTY ((ushort)0x8000) -#define BD_ENET_RX_WRAP ((ushort)0x2000) -#define BD_ENET_RX_INTR ((ushort)0x1000) -#define BD_ENET_RX_LAST ((ushort)0x0800) -#define BD_ENET_RX_FIRST ((ushort)0x0400) -#define BD_ENET_RX_MISS ((ushort)0x0100) -#define BD_ENET_RX_BC ((ushort)0x0080) /* FCC Only */ -#define BD_ENET_RX_MC ((ushort)0x0040) /* FCC Only */ -#define BD_ENET_RX_LG ((ushort)0x0020) -#define BD_ENET_RX_NO ((ushort)0x0010) -#define BD_ENET_RX_SH ((ushort)0x0008) -#define BD_ENET_RX_CR ((ushort)0x0004) -#define BD_ENET_RX_OV ((ushort)0x0002) -#define BD_ENET_RX_CL ((ushort)0x0001) -#define BD_ENET_RX_STATS ((ushort)0x01ff) /* All status bits */ - -/* Buffer descriptor control/status used by Ethernet transmit. - * Common to SCC and FCC. - */ -#define BD_ENET_TX_READY ((ushort)0x8000) -#define BD_ENET_TX_PAD ((ushort)0x4000) -#define BD_ENET_TX_WRAP ((ushort)0x2000) -#define BD_ENET_TX_INTR ((ushort)0x1000) -#define BD_ENET_TX_LAST ((ushort)0x0800) -#define BD_ENET_TX_TC ((ushort)0x0400) -#define BD_ENET_TX_DEF ((ushort)0x0200) -#define BD_ENET_TX_HB ((ushort)0x0100) -#define BD_ENET_TX_LC ((ushort)0x0080) -#define BD_ENET_TX_RL ((ushort)0x0040) -#define BD_ENET_TX_RCMASK ((ushort)0x003c) -#define BD_ENET_TX_UN ((ushort)0x0002) -#define BD_ENET_TX_CSL ((ushort)0x0001) -#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */ - -/* SCC as UART -*/ -typedef struct scc_uart { - sccp_t scc_genscc; - uint scc_res1; /* Reserved */ - uint scc_res2; /* Reserved */ - ushort scc_maxidl; /* Maximum idle chars */ - ushort scc_idlc; /* temp idle counter */ - ushort scc_brkcr; /* Break count register */ - ushort scc_parec; /* receive parity error counter */ - ushort scc_frmec; /* receive framing error counter */ - ushort scc_nosec; /* receive noise counter */ - ushort scc_brkec; /* receive break condition counter */ - ushort scc_brkln; /* last received break length */ - ushort scc_uaddr1; /* UART address character 1 */ - ushort scc_uaddr2; /* UART address character 2 */ - ushort scc_rtemp; /* Temp storage */ - ushort scc_toseq; /* Transmit out of sequence char */ - ushort scc_char1; /* control character 1 */ - ushort scc_char2; /* control character 2 */ - ushort scc_char3; /* control character 3 */ - ushort scc_char4; /* control character 4 */ - ushort scc_char5; /* control character 5 */ - ushort scc_char6; /* control character 6 */ - ushort scc_char7; /* control character 7 */ - ushort scc_char8; /* control character 8 */ - ushort scc_rccm; /* receive control character mask */ - ushort scc_rccr; /* receive control character register */ - ushort scc_rlbc; /* receive last break character */ -} scc_uart_t; - -/* SCC Event and Mask registers when it is used as a UART. -*/ -#define UART_SCCM_GLR ((ushort)0x1000) -#define UART_SCCM_GLT ((ushort)0x0800) -#define UART_SCCM_AB ((ushort)0x0200) -#define UART_SCCM_IDL ((ushort)0x0100) -#define UART_SCCM_GRA ((ushort)0x0080) -#define UART_SCCM_BRKE ((ushort)0x0040) -#define UART_SCCM_BRKS ((ushort)0x0020) -#define UART_SCCM_CCR ((ushort)0x0008) -#define UART_SCCM_BSY ((ushort)0x0004) -#define UART_SCCM_TX ((ushort)0x0002) -#define UART_SCCM_RX ((ushort)0x0001) - -/* The SCC PSMR when used as a UART. -*/ -#define SCU_PSMR_FLC ((ushort)0x8000) -#define SCU_PSMR_SL ((ushort)0x4000) -#define SCU_PSMR_CL ((ushort)0x3000) -#define SCU_PSMR_UM ((ushort)0x0c00) -#define SCU_PSMR_FRZ ((ushort)0x0200) -#define SCU_PSMR_RZS ((ushort)0x0100) -#define SCU_PSMR_SYN ((ushort)0x0080) -#define SCU_PSMR_DRT ((ushort)0x0040) -#define SCU_PSMR_PEN ((ushort)0x0010) -#define SCU_PSMR_RPM ((ushort)0x000c) -#define SCU_PSMR_REVP ((ushort)0x0008) -#define SCU_PSMR_TPM ((ushort)0x0003) -#define SCU_PSMR_TEVP ((ushort)0x0003) - -/* CPM Transparent mode SCC. - */ -typedef struct scc_trans { - sccp_t st_genscc; - uint st_cpres; /* Preset CRC */ - uint st_cmask; /* Constant mask for CRC */ -} scc_trans_t; - -#define BD_SCC_TX_LAST ((ushort)0x0800) - -/* How about some FCCs..... -*/ -#define FCC_GFMR_DIAG_NORM ((uint)0x00000000) -#define FCC_GFMR_DIAG_LE ((uint)0x40000000) -#define FCC_GFMR_DIAG_AE ((uint)0x80000000) -#define FCC_GFMR_DIAG_ALE ((uint)0xc0000000) -#define FCC_GFMR_TCI ((uint)0x20000000) -#define FCC_GFMR_TRX ((uint)0x10000000) -#define FCC_GFMR_TTX ((uint)0x08000000) -#define FCC_GFMR_TTX ((uint)0x08000000) -#define FCC_GFMR_CDP ((uint)0x04000000) -#define FCC_GFMR_CTSP ((uint)0x02000000) -#define FCC_GFMR_CDS ((uint)0x01000000) -#define FCC_GFMR_CTSS ((uint)0x00800000) -#define FCC_GFMR_SYNL_NONE ((uint)0x00000000) -#define FCC_GFMR_SYNL_AUTO ((uint)0x00004000) -#define FCC_GFMR_SYNL_8 ((uint)0x00008000) -#define FCC_GFMR_SYNL_16 ((uint)0x0000c000) -#define FCC_GFMR_RTSM ((uint)0x00002000) -#define FCC_GFMR_RENC_NRZ ((uint)0x00000000) -#define FCC_GFMR_RENC_NRZI ((uint)0x00000800) -#define FCC_GFMR_REVD ((uint)0x00000400) -#define FCC_GFMR_TENC_NRZ ((uint)0x00000000) -#define FCC_GFMR_TENC_NRZI ((uint)0x00000100) -#define FCC_GFMR_TCRC_16 ((uint)0x00000000) -#define FCC_GFMR_TCRC_32 ((uint)0x00000080) -#define FCC_GFMR_ENR ((uint)0x00000020) -#define FCC_GFMR_ENT ((uint)0x00000010) -#define FCC_GFMR_MODE_ENET ((uint)0x0000000c) -#define FCC_GFMR_MODE_ATM ((uint)0x0000000a) -#define FCC_GFMR_MODE_HDLC ((uint)0x00000000) - -/* Generic FCC parameter ram. -*/ -typedef struct fcc_param { - ushort fcc_riptr; /* Rx Internal temp pointer */ - ushort fcc_tiptr; /* Tx Internal temp pointer */ - ushort fcc_res1; - ushort fcc_mrblr; /* Max receive buffer length, mod 32 bytes */ - uint fcc_rstate; /* Upper byte is Func code, must be set */ - uint fcc_rbase; /* Receive BD base */ - ushort fcc_rbdstat; /* RxBD status */ - ushort fcc_rbdlen; /* RxBD down counter */ - uint fcc_rdptr; /* RxBD internal data pointer */ - uint fcc_tstate; /* Upper byte is Func code, must be set */ - uint fcc_tbase; /* Transmit BD base */ - ushort fcc_tbdstat; /* TxBD status */ - ushort fcc_tbdlen; /* TxBD down counter */ - uint fcc_tdptr; /* TxBD internal data pointer */ - uint fcc_rbptr; /* Rx BD Internal buf pointer */ - uint fcc_tbptr; /* Tx BD Internal buf pointer */ - uint fcc_rcrc; /* Rx temp CRC */ - uint fcc_res2; - uint fcc_tcrc; /* Tx temp CRC */ -} fccp_t; - - -/* Ethernet controller through FCC. -*/ -typedef struct fcc_enet { - fccp_t fen_genfcc; - uint fen_statbuf; /* Internal status buffer */ - uint fen_camptr; /* CAM address */ - uint fen_cmask; /* Constant mask for CRC */ - uint fen_cpres; /* Preset CRC */ - uint fen_crcec; /* CRC Error counter */ - uint fen_alec; /* alignment error counter */ - uint fen_disfc; /* discard frame counter */ - ushort fen_retlim; /* Retry limit */ - ushort fen_retcnt; /* Retry counter */ - ushort fen_pper; /* Persistence */ - ushort fen_boffcnt; /* backoff counter */ - uint fen_gaddrh; /* Group address filter, high 32-bits */ - uint fen_gaddrl; /* Group address filter, low 32-bits */ - ushort fen_tfcstat; /* out of sequence TxBD */ - ushort fen_tfclen; - uint fen_tfcptr; - ushort fen_mflr; /* Maximum frame length (1518) */ - ushort fen_paddrh; /* MAC address */ - ushort fen_paddrm; - ushort fen_paddrl; - ushort fen_ibdcount; /* Internal BD counter */ - ushort fen_ibdstart; /* Internal BD start pointer */ - ushort fen_ibdend; /* Internal BD end pointer */ - ushort fen_txlen; /* Internal Tx frame length counter */ - uint fen_ibdbase[8]; /* Internal use */ - uint fen_iaddrh; /* Individual address filter */ - uint fen_iaddrl; - ushort fen_minflr; /* Minimum frame length (64) */ - ushort fen_taddrh; /* Filter transfer MAC address */ - ushort fen_taddrm; - ushort fen_taddrl; - ushort fen_padptr; /* Pointer to pad byte buffer */ - ushort fen_cftype; /* control frame type */ - ushort fen_cfrange; /* control frame range */ - ushort fen_maxb; /* maximum BD count */ - ushort fen_maxd1; /* Max DMA1 length (1520) */ - ushort fen_maxd2; /* Max DMA2 length (1520) */ - ushort fen_maxd; /* internal max DMA count */ - ushort fen_dmacnt; /* internal DMA counter */ - uint fen_octc; /* Total octect counter */ - uint fen_colc; /* Total collision counter */ - uint fen_broc; /* Total broadcast packet counter */ - uint fen_mulc; /* Total multicast packet count */ - uint fen_uspc; /* Total packets < 64 bytes */ - uint fen_frgc; /* Total packets < 64 bytes with errors */ - uint fen_ospc; /* Total packets > 1518 */ - uint fen_jbrc; /* Total packets > 1518 with errors */ - uint fen_p64c; /* Total packets == 64 bytes */ - uint fen_p65c; /* Total packets 64 < bytes <= 127 */ - uint fen_p128c; /* Total packets 127 < bytes <= 255 */ - uint fen_p256c; /* Total packets 256 < bytes <= 511 */ - uint fen_p512c; /* Total packets 512 < bytes <= 1023 */ - uint fen_p1024c; /* Total packets 1024 < bytes <= 1518 */ - uint fen_cambuf; /* Internal CAM buffer poiner */ - ushort fen_rfthr; /* Received frames threshold */ - ushort fen_rfcnt; /* Received frames count */ -} fcc_enet_t; - -/* FCC Event/Mask register as used by Ethernet. -*/ -#define FCC_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */ -#define FCC_ENET_RXC ((ushort)0x0040) /* Control Frame Received */ -#define FCC_ENET_TXC ((ushort)0x0020) /* Out of seq. Tx sent */ -#define FCC_ENET_TXE ((ushort)0x0010) /* Transmit Error */ -#define FCC_ENET_RXF ((ushort)0x0008) /* Full frame received */ -#define FCC_ENET_BSY ((ushort)0x0004) /* Busy. Rx Frame dropped */ -#define FCC_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */ -#define FCC_ENET_RXB ((ushort)0x0001) /* A buffer was received */ - -/* FCC Mode Register (FPSMR) as used by Ethernet. -*/ -#define FCC_PSMR_HBC ((uint)0x80000000) /* Enable heartbeat */ -#define FCC_PSMR_FC ((uint)0x40000000) /* Force Collision */ -#define FCC_PSMR_SBT ((uint)0x20000000) /* Stop backoff timer */ -#define FCC_PSMR_LPB ((uint)0x10000000) /* Local protect. 1 = FDX */ -#define FCC_PSMR_LCW ((uint)0x08000000) /* Late collision select */ -#define FCC_PSMR_FDE ((uint)0x04000000) /* Full Duplex Enable */ -#define FCC_PSMR_MON ((uint)0x02000000) /* RMON Enable */ -#define FCC_PSMR_PRO ((uint)0x00400000) /* Promiscuous Enable */ -#define FCC_PSMR_FCE ((uint)0x00200000) /* Flow Control Enable */ -#define FCC_PSMR_RSH ((uint)0x00100000) /* Receive Short Frames */ -#define FCC_PSMR_CAM ((uint)0x00000400) /* CAM enable */ -#define FCC_PSMR_BRO ((uint)0x00000200) /* Broadcast pkt discard */ -#define FCC_PSMR_ENCRC ((uint)0x00000080) /* Use 32-bit CRC */ - -/* IIC parameter RAM. -*/ -typedef struct iic { - ushort iic_rbase; /* Rx Buffer descriptor base address */ - ushort iic_tbase; /* Tx Buffer descriptor base address */ - u_char iic_rfcr; /* Rx function code */ - u_char iic_tfcr; /* Tx function code */ - ushort iic_mrblr; /* Max receive buffer length */ - uint iic_rstate; /* Internal */ - uint iic_rdp; /* Internal */ - ushort iic_rbptr; /* Internal */ - ushort iic_rbc; /* Internal */ - uint iic_rxtmp; /* Internal */ - uint iic_tstate; /* Internal */ - uint iic_tdp; /* Internal */ - ushort iic_tbptr; /* Internal */ - ushort iic_tbc; /* Internal */ - uint iic_txtmp; /* Internal */ -} iic_t; - -/* SPI parameter RAM. -*/ -typedef struct spi { - ushort spi_rbase; /* Rx Buffer descriptor base address */ - ushort spi_tbase; /* Tx Buffer descriptor base address */ - u_char spi_rfcr; /* Rx function code */ - u_char spi_tfcr; /* Tx function code */ - ushort spi_mrblr; /* Max receive buffer length */ - uint spi_rstate; /* Internal */ - uint spi_rdp; /* Internal */ - ushort spi_rbptr; /* Internal */ - ushort spi_rbc; /* Internal */ - uint spi_rxtmp; /* Internal */ - uint spi_tstate; /* Internal */ - uint spi_tdp; /* Internal */ - ushort spi_tbptr; /* Internal */ - ushort spi_tbc; /* Internal */ - uint spi_txtmp; /* Internal */ - uint spi_res; /* Tx temp. */ - uint spi_res1[4]; /* SDMA temp. */ -} spi_t; - -/* SPI Mode register. -*/ -#define SPMODE_LOOP ((ushort)0x4000) /* Loopback */ -#define SPMODE_CI ((ushort)0x2000) /* Clock Invert */ -#define SPMODE_CP ((ushort)0x1000) /* Clock Phase */ -#define SPMODE_DIV16 ((ushort)0x0800) /* BRG/16 mode */ -#define SPMODE_REV ((ushort)0x0400) /* Reversed Data */ -#define SPMODE_MSTR ((ushort)0x0200) /* SPI Master */ -#define SPMODE_EN ((ushort)0x0100) /* Enable */ -#define SPMODE_LENMSK ((ushort)0x00f0) /* character length */ -#define SPMODE_PMMSK ((ushort)0x000f) /* prescale modulus */ - -#define SPMODE_LEN(x) ((((x)-1)&0xF)<<4) -#define SPMODE_PM(x) ((x) &0xF) - -#define SPI_EB ((u_char)0x10) /* big endian byte order */ - -#define BD_IIC_START ((ushort)0x0400) - -/*----------------------------------------------------------------------- - * CMXFCR - CMX FCC Clock Route Register 15-12 - */ -#define CMXFCR_FC1 0x40000000 /* FCC1 connection */ -#define CMXFCR_RF1CS_MSK 0x38000000 /* Receive FCC1 Clock Source Mask */ -#define CMXFCR_TF1CS_MSK 0x07000000 /* Transmit FCC1 Clock Source Mask */ -#define CMXFCR_FC2 0x00400000 /* FCC2 connection */ -#define CMXFCR_RF2CS_MSK 0x00380000 /* Receive FCC2 Clock Source Mask */ -#define CMXFCR_TF2CS_MSK 0x00070000 /* Transmit FCC2 Clock Source Mask */ -#define CMXFCR_FC3 0x00004000 /* FCC3 connection */ -#define CMXFCR_RF3CS_MSK 0x00003800 /* Receive FCC3 Clock Source Mask */ -#define CMXFCR_TF3CS_MSK 0x00000700 /* Transmit FCC3 Clock Source Mask */ - -#define CMXFCR_RF1CS_BRG5 0x00000000 /* Receive FCC1 Clock Source is BRG5 */ -#define CMXFCR_RF1CS_BRG6 0x08000000 /* Receive FCC1 Clock Source is BRG6 */ -#define CMXFCR_RF1CS_BRG7 0x10000000 /* Receive FCC1 Clock Source is BRG7 */ -#define CMXFCR_RF1CS_BRG8 0x18000000 /* Receive FCC1 Clock Source is BRG8 */ -#define CMXFCR_RF1CS_CLK9 0x20000000 /* Receive FCC1 Clock Source is CLK9 */ -#define CMXFCR_RF1CS_CLK10 0x28000000 /* Receive FCC1 Clock Source is CLK10 */ -#define CMXFCR_RF1CS_CLK11 0x30000000 /* Receive FCC1 Clock Source is CLK11 */ -#define CMXFCR_RF1CS_CLK12 0x38000000 /* Receive FCC1 Clock Source is CLK12 */ - -#define CMXFCR_TF1CS_BRG5 0x00000000 /* Transmit FCC1 Clock Source is BRG5 */ -#define CMXFCR_TF1CS_BRG6 0x01000000 /* Transmit FCC1 Clock Source is BRG6 */ -#define CMXFCR_TF1CS_BRG7 0x02000000 /* Transmit FCC1 Clock Source is BRG7 */ -#define CMXFCR_TF1CS_BRG8 0x03000000 /* Transmit FCC1 Clock Source is BRG8 */ -#define CMXFCR_TF1CS_CLK9 0x04000000 /* Transmit FCC1 Clock Source is CLK9 */ -#define CMXFCR_TF1CS_CLK10 0x05000000 /* Transmit FCC1 Clock Source is CLK10 */ -#define CMXFCR_TF1CS_CLK11 0x06000000 /* Transmit FCC1 Clock Source is CLK11 */ -#define CMXFCR_TF1CS_CLK12 0x07000000 /* Transmit FCC1 Clock Source is CLK12 */ - -#define CMXFCR_RF2CS_BRG5 0x00000000 /* Receive FCC2 Clock Source is BRG5 */ -#define CMXFCR_RF2CS_BRG6 0x00080000 /* Receive FCC2 Clock Source is BRG6 */ -#define CMXFCR_RF2CS_BRG7 0x00100000 /* Receive FCC2 Clock Source is BRG7 */ -#define CMXFCR_RF2CS_BRG8 0x00180000 /* Receive FCC2 Clock Source is BRG8 */ -#define CMXFCR_RF2CS_CLK13 0x00200000 /* Receive FCC2 Clock Source is CLK13 */ -#define CMXFCR_RF2CS_CLK14 0x00280000 /* Receive FCC2 Clock Source is CLK14 */ -#define CMXFCR_RF2CS_CLK15 0x00300000 /* Receive FCC2 Clock Source is CLK15 */ -#define CMXFCR_RF2CS_CLK16 0x00380000 /* Receive FCC2 Clock Source is CLK16 */ - -#define CMXFCR_TF2CS_BRG5 0x00000000 /* Transmit FCC2 Clock Source is BRG5 */ -#define CMXFCR_TF2CS_BRG6 0x00010000 /* Transmit FCC2 Clock Source is BRG6 */ -#define CMXFCR_TF2CS_BRG7 0x00020000 /* Transmit FCC2 Clock Source is BRG7 */ -#define CMXFCR_TF2CS_BRG8 0x00030000 /* Transmit FCC2 Clock Source is BRG8 */ -#define CMXFCR_TF2CS_CLK13 0x00040000 /* Transmit FCC2 Clock Source is CLK13 */ -#define CMXFCR_TF2CS_CLK14 0x00050000 /* Transmit FCC2 Clock Source is CLK14 */ -#define CMXFCR_TF2CS_CLK15 0x00060000 /* Transmit FCC2 Clock Source is CLK15 */ -#define CMXFCR_TF2CS_CLK16 0x00070000 /* Transmit FCC2 Clock Source is CLK16 */ - -#define CMXFCR_RF3CS_BRG5 0x00000000 /* Receive FCC3 Clock Source is BRG5 */ -#define CMXFCR_RF3CS_BRG6 0x00000800 /* Receive FCC3 Clock Source is BRG6 */ -#define CMXFCR_RF3CS_BRG7 0x00001000 /* Receive FCC3 Clock Source is BRG7 */ -#define CMXFCR_RF3CS_BRG8 0x00001800 /* Receive FCC3 Clock Source is BRG8 */ -#define CMXFCR_RF3CS_CLK13 0x00002000 /* Receive FCC3 Clock Source is CLK13 */ -#define CMXFCR_RF3CS_CLK14 0x00002800 /* Receive FCC3 Clock Source is CLK14 */ -#define CMXFCR_RF3CS_CLK15 0x00003000 /* Receive FCC3 Clock Source is CLK15 */ -#define CMXFCR_RF3CS_CLK16 0x00003800 /* Receive FCC3 Clock Source is CLK16 */ - -#define CMXFCR_TF3CS_BRG5 0x00000000 /* Transmit FCC3 Clock Source is BRG5 */ -#define CMXFCR_TF3CS_BRG6 0x00000100 /* Transmit FCC3 Clock Source is BRG6 */ -#define CMXFCR_TF3CS_BRG7 0x00000200 /* Transmit FCC3 Clock Source is BRG7 */ -#define CMXFCR_TF3CS_BRG8 0x00000300 /* Transmit FCC3 Clock Source is BRG8 */ -#define CMXFCR_TF3CS_CLK13 0x00000400 /* Transmit FCC3 Clock Source is CLK13 */ -#define CMXFCR_TF3CS_CLK14 0x00000500 /* Transmit FCC3 Clock Source is CLK14 */ -#define CMXFCR_TF3CS_CLK15 0x00000600 /* Transmit FCC3 Clock Source is CLK15 */ -#define CMXFCR_TF3CS_CLK16 0x00000700 /* Transmit FCC3 Clock Source is CLK16 */ - -/*----------------------------------------------------------------------- - * CMXSCR - CMX SCC Clock Route Register 15-14 - */ -#define CMXSCR_GR1 0x80000000 /* Grant Support of SCC1 */ -#define CMXSCR_SC1 0x40000000 /* SCC1 connection */ -#define CMXSCR_RS1CS_MSK 0x38000000 /* Receive SCC1 Clock Source Mask */ -#define CMXSCR_TS1CS_MSK 0x07000000 /* Transmit SCC1 Clock Source Mask */ -#define CMXSCR_GR2 0x00800000 /* Grant Support of SCC2 */ -#define CMXSCR_SC2 0x00400000 /* SCC2 connection */ -#define CMXSCR_RS2CS_MSK 0x00380000 /* Receive SCC2 Clock Source Mask */ -#define CMXSCR_TS2CS_MSK 0x00070000 /* Transmit SCC2 Clock Source Mask */ -#define CMXSCR_GR3 0x00008000 /* Grant Support of SCC3 */ -#define CMXSCR_SC3 0x00004000 /* SCC3 connection */ -#define CMXSCR_RS3CS_MSK 0x00003800 /* Receive SCC3 Clock Source Mask */ -#define CMXSCR_TS3CS_MSK 0x00000700 /* Transmit SCC3 Clock Source Mask */ -#define CMXSCR_GR4 0x00000080 /* Grant Support of SCC4 */ -#define CMXSCR_SC4 0x00000040 /* SCC4 connection */ -#define CMXSCR_RS4CS_MSK 0x00000038 /* Receive SCC4 Clock Source Mask */ -#define CMXSCR_TS4CS_MSK 0x00000007 /* Transmit SCC4 Clock Source Mask */ - -#define CMXSCR_RS1CS_BRG1 0x00000000 /* SCC1 Rx Clock Source is BRG1 */ -#define CMXSCR_RS1CS_BRG2 0x08000000 /* SCC1 Rx Clock Source is BRG2 */ -#define CMXSCR_RS1CS_BRG3 0x10000000 /* SCC1 Rx Clock Source is BRG3 */ -#define CMXSCR_RS1CS_BRG4 0x18000000 /* SCC1 Rx Clock Source is BRG4 */ -#define CMXSCR_RS1CS_CLK11 0x20000000 /* SCC1 Rx Clock Source is CLK11 */ -#define CMXSCR_RS1CS_CLK12 0x28000000 /* SCC1 Rx Clock Source is CLK12 */ -#define CMXSCR_RS1CS_CLK3 0x30000000 /* SCC1 Rx Clock Source is CLK3 */ -#define CMXSCR_RS1CS_CLK4 0x38000000 /* SCC1 Rx Clock Source is CLK4 */ - -#define CMXSCR_TS1CS_BRG1 0x00000000 /* SCC1 Tx Clock Source is BRG1 */ -#define CMXSCR_TS1CS_BRG2 0x01000000 /* SCC1 Tx Clock Source is BRG2 */ -#define CMXSCR_TS1CS_BRG3 0x02000000 /* SCC1 Tx Clock Source is BRG3 */ -#define CMXSCR_TS1CS_BRG4 0x03000000 /* SCC1 Tx Clock Source is BRG4 */ -#define CMXSCR_TS1CS_CLK11 0x04000000 /* SCC1 Tx Clock Source is CLK11 */ -#define CMXSCR_TS1CS_CLK12 0x05000000 /* SCC1 Tx Clock Source is CLK12 */ -#define CMXSCR_TS1CS_CLK3 0x06000000 /* SCC1 Tx Clock Source is CLK3 */ -#define CMXSCR_TS1CS_CLK4 0x07000000 /* SCC1 Tx Clock Source is CLK4 */ - -#define CMXSCR_RS2CS_BRG1 0x00000000 /* SCC2 Rx Clock Source is BRG1 */ -#define CMXSCR_RS2CS_BRG2 0x00080000 /* SCC2 Rx Clock Source is BRG2 */ -#define CMXSCR_RS2CS_BRG3 0x00100000 /* SCC2 Rx Clock Source is BRG3 */ -#define CMXSCR_RS2CS_BRG4 0x00180000 /* SCC2 Rx Clock Source is BRG4 */ -#define CMXSCR_RS2CS_CLK11 0x00200000 /* SCC2 Rx Clock Source is CLK11 */ -#define CMXSCR_RS2CS_CLK12 0x00280000 /* SCC2 Rx Clock Source is CLK12 */ -#define CMXSCR_RS2CS_CLK3 0x00300000 /* SCC2 Rx Clock Source is CLK3 */ -#define CMXSCR_RS2CS_CLK4 0x00380000 /* SCC2 Rx Clock Source is CLK4 */ - -#define CMXSCR_TS2CS_BRG1 0x00000000 /* SCC2 Tx Clock Source is BRG1 */ -#define CMXSCR_TS2CS_BRG2 0x00010000 /* SCC2 Tx Clock Source is BRG2 */ -#define CMXSCR_TS2CS_BRG3 0x00020000 /* SCC2 Tx Clock Source is BRG3 */ -#define CMXSCR_TS2CS_BRG4 0x00030000 /* SCC2 Tx Clock Source is BRG4 */ -#define CMXSCR_TS2CS_CLK11 0x00040000 /* SCC2 Tx Clock Source is CLK11 */ -#define CMXSCR_TS2CS_CLK12 0x00050000 /* SCC2 Tx Clock Source is CLK12 */ -#define CMXSCR_TS2CS_CLK3 0x00060000 /* SCC2 Tx Clock Source is CLK3 */ -#define CMXSCR_TS2CS_CLK4 0x00070000 /* SCC2 Tx Clock Source is CLK4 */ - -#define CMXSCR_RS3CS_BRG1 0x00000000 /* SCC3 Rx Clock Source is BRG1 */ -#define CMXSCR_RS3CS_BRG2 0x00000800 /* SCC3 Rx Clock Source is BRG2 */ -#define CMXSCR_RS3CS_BRG3 0x00001000 /* SCC3 Rx Clock Source is BRG3 */ -#define CMXSCR_RS3CS_BRG4 0x00001800 /* SCC3 Rx Clock Source is BRG4 */ -#define CMXSCR_RS3CS_CLK5 0x00002000 /* SCC3 Rx Clock Source is CLK5 */ -#define CMXSCR_RS3CS_CLK6 0x00002800 /* SCC3 Rx Clock Source is CLK6 */ -#define CMXSCR_RS3CS_CLK7 0x00003000 /* SCC3 Rx Clock Source is CLK7 */ -#define CMXSCR_RS3CS_CLK8 0x00003800 /* SCC3 Rx Clock Source is CLK8 */ - -#define CMXSCR_TS3CS_BRG1 0x00000000 /* SCC3 Tx Clock Source is BRG1 */ -#define CMXSCR_TS3CS_BRG2 0x00000100 /* SCC3 Tx Clock Source is BRG2 */ -#define CMXSCR_TS3CS_BRG3 0x00000200 /* SCC3 Tx Clock Source is BRG3 */ -#define CMXSCR_TS3CS_BRG4 0x00000300 /* SCC3 Tx Clock Source is BRG4 */ -#define CMXSCR_TS3CS_CLK5 0x00000400 /* SCC3 Tx Clock Source is CLK5 */ -#define CMXSCR_TS3CS_CLK6 0x00000500 /* SCC3 Tx Clock Source is CLK6 */ -#define CMXSCR_TS3CS_CLK7 0x00000600 /* SCC3 Tx Clock Source is CLK7 */ -#define CMXSCR_TS3CS_CLK8 0x00000700 /* SCC3 Tx Clock Source is CLK8 */ - -#define CMXSCR_RS4CS_BRG1 0x00000000 /* SCC4 Rx Clock Source is BRG1 */ -#define CMXSCR_RS4CS_BRG2 0x00000008 /* SCC4 Rx Clock Source is BRG2 */ -#define CMXSCR_RS4CS_BRG3 0x00000010 /* SCC4 Rx Clock Source is BRG3 */ -#define CMXSCR_RS4CS_BRG4 0x00000018 /* SCC4 Rx Clock Source is BRG4 */ -#define CMXSCR_RS4CS_CLK5 0x00000020 /* SCC4 Rx Clock Source is CLK5 */ -#define CMXSCR_RS4CS_CLK6 0x00000028 /* SCC4 Rx Clock Source is CLK6 */ -#define CMXSCR_RS4CS_CLK7 0x00000030 /* SCC4 Rx Clock Source is CLK7 */ -#define CMXSCR_RS4CS_CLK8 0x00000038 /* SCC4 Rx Clock Source is CLK8 */ - -#define CMXSCR_TS4CS_BRG1 0x00000000 /* SCC4 Tx Clock Source is BRG1 */ -#define CMXSCR_TS4CS_BRG2 0x00000001 /* SCC4 Tx Clock Source is BRG2 */ -#define CMXSCR_TS4CS_BRG3 0x00000002 /* SCC4 Tx Clock Source is BRG3 */ -#define CMXSCR_TS4CS_BRG4 0x00000003 /* SCC4 Tx Clock Source is BRG4 */ -#define CMXSCR_TS4CS_CLK5 0x00000004 /* SCC4 Tx Clock Source is CLK5 */ -#define CMXSCR_TS4CS_CLK6 0x00000005 /* SCC4 Tx Clock Source is CLK6 */ -#define CMXSCR_TS4CS_CLK7 0x00000006 /* SCC4 Tx Clock Source is CLK7 */ -#define CMXSCR_TS4CS_CLK8 0x00000007 /* SCC4 Tx Clock Source is CLK8 */ - -#endif /* __CPM_85XX__ */ diff --git a/arch/powerpc/include/asm/global_data.h b/arch/powerpc/include/asm/global_data.h index 2975255bfe23..770adcd30f29 100644 --- a/arch/powerpc/include/asm/global_data.h +++ b/arch/powerpc/include/asm/global_data.h @@ -19,13 +19,6 @@ struct arch_global_data { #endif #if defined(CONFIG_MPC8xx) unsigned long brg_clk; -#endif -#if defined(CONFIG_CPM2) - /* There are many clocks on the MPC8260 - see page 9-5 */ - unsigned long vco_out; - unsigned long cpm_clk; - unsigned long scc_clk; - unsigned long brg_clk; #endif /* TODO: sjg(a)chromium.org: Should these be unslgned long? */ #if defined(CONFIG_MPC83xx) @@ -88,10 +81,6 @@ struct arch_global_data { unsigned long arbiter_event_attributes; unsigned long arbiter_event_address; #endif -#if defined(CONFIG_CPM2) - unsigned int dp_alloc_base; - unsigned int dp_alloc_top; -#endif #ifdef CONFIG_SYS_FPGA_COUNT unsigned fpga_state[CONFIG_SYS_FPGA_COUNT]; #endif diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h index 770705a8794b..b8bc58448217 100644 --- a/arch/powerpc/include/asm/immap_85xx.h +++ b/arch/powerpc/include/asm/immap_85xx.h @@ -921,330 +921,6 @@ typedef struct ccsr_pic { u8 res150[130892]; } ccsr_pic_t; -/* CPM Block */ -#ifndef CONFIG_CPM2 -typedef struct ccsr_cpm { - u8 res[262144]; -} ccsr_cpm_t; -#else -/* - * DPARM - * General SIU - */ -typedef struct ccsr_cpm_siu { - u8 res1[80]; - u32 smaer; - u32 smser; - u32 smevr; - u8 res2[4]; - u32 lmaer; - u32 lmser; - u32 lmevr; - u8 res3[2964]; -} ccsr_cpm_siu_t; - -/* IRQ Controller */ -typedef struct ccsr_cpm_intctl { - u16 sicr; - u8 res1[2]; - u32 sivec; - u32 sipnrh; - u32 sipnrl; - u32 siprr; - u32 scprrh; - u32 scprrl; - u32 simrh; - u32 simrl; - u32 siexr; - u8 res2[88]; - u32 sccr; - u8 res3[124]; -} ccsr_cpm_intctl_t; - -/* input/output port */ -typedef struct ccsr_cpm_iop { - u32 pdira; - u32 ppara; - u32 psora; - u32 podra; - u32 pdata; - u8 res1[12]; - u32 pdirb; - u32 pparb; - u32 psorb; - u32 podrb; - u32 pdatb; - u8 res2[12]; - u32 pdirc; - u32 pparc; - u32 psorc; - u32 podrc; - u32 pdatc; - u8 res3[12]; - u32 pdird; - u32 ppard; - u32 psord; - u32 podrd; - u32 pdatd; - u8 res4[12]; -} ccsr_cpm_iop_t; - -/* CPM timers */ -typedef struct ccsr_cpm_timer { - u8 tgcr1; - u8 res1[3]; - u8 tgcr2; - u8 res2[11]; - u16 tmr1; - u16 tmr2; - u16 trr1; - u16 trr2; - u16 tcr1; - u16 tcr2; - u16 tcn1; - u16 tcn2; - u16 tmr3; - u16 tmr4; - u16 trr3; - u16 trr4; - u16 tcr3; - u16 tcr4; - u16 tcn3; - u16 tcn4; - u16 ter1; - u16 ter2; - u16 ter3; - u16 ter4; - u8 res3[608]; -} ccsr_cpm_timer_t; - -/* SDMA */ -typedef struct ccsr_cpm_sdma { - u8 sdsr; - u8 res1[3]; - u8 sdmr; - u8 res2[739]; -} ccsr_cpm_sdma_t; - -/* FCC1 */ -typedef struct ccsr_cpm_fcc1 { - u32 gfmr; - u32 fpsmr; - u16 ftodr; - u8 res1[2]; - u16 fdsr; - u8 res2[2]; - u16 fcce; - u8 res3[2]; - u16 fccm; - u8 res4[2]; - u8 fccs; - u8 res5[3]; - u8 ftirr_phy[4]; -} ccsr_cpm_fcc1_t; - -/* FCC2 */ -typedef struct ccsr_cpm_fcc2 { - u32 gfmr; - u32 fpsmr; - u16 ftodr; - u8 res1[2]; - u16 fdsr; - u8 res2[2]; - u16 fcce; - u8 res3[2]; - u16 fccm; - u8 res4[2]; - u8 fccs; - u8 res5[3]; - u8 ftirr_phy[4]; -} ccsr_cpm_fcc2_t; - -/* FCC3 */ -typedef struct ccsr_cpm_fcc3 { - u32 gfmr; - u32 fpsmr; - u16 ftodr; - u8 res1[2]; - u16 fdsr; - u8 res2[2]; - u16 fcce; - u8 res3[2]; - u16 fccm; - u8 res4[2]; - u8 fccs; - u8 res5[3]; - u8 res[36]; -} ccsr_cpm_fcc3_t; - -/* FCC1 extended */ -typedef struct ccsr_cpm_fcc1_ext { - u32 firper; - u32 firer; - u32 firsr_h; - u32 firsr_l; - u8 gfemr; - u8 res[15]; - -} ccsr_cpm_fcc1_ext_t; - -/* FCC2 extended */ -typedef struct ccsr_cpm_fcc2_ext { - u32 firper; - u32 firer; - u32 firsr_h; - u32 firsr_l; - u8 gfemr; - u8 res[31]; -} ccsr_cpm_fcc2_ext_t; - -/* FCC3 extended */ -typedef struct ccsr_cpm_fcc3_ext { - u8 gfemr; - u8 res[47]; -} ccsr_cpm_fcc3_ext_t; - -/* TC layers */ -typedef struct ccsr_cpm_tmp1 { - u8 res[496]; -} ccsr_cpm_tmp1_t; - -/* BRGs:5,6,7,8 */ -typedef struct ccsr_cpm_brg2 { - u32 brgc5; - u32 brgc6; - u32 brgc7; - u32 brgc8; - u8 res[608]; -} ccsr_cpm_brg2_t; - -/* I2C */ -typedef struct ccsr_cpm_i2c { - u8 i2mod; - u8 res1[3]; - u8 i2add; - u8 res2[3]; - u8 i2brg; - u8 res3[3]; - u8 i2com; - u8 res4[3]; - u8 i2cer; - u8 res5[3]; - u8 i2cmr; - u8 res6[331]; -} ccsr_cpm_i2c_t; - -/* CPM core */ -typedef struct ccsr_cpm_cp { - u32 cpcr; - u32 rccr; - u8 res1[14]; - u16 rter; - u8 res2[2]; - u16 rtmr; - u16 rtscr; - u8 res3[2]; - u32 rtsr; - u8 res4[12]; -} ccsr_cpm_cp_t; - -/* BRGs:1,2,3,4 */ -typedef struct ccsr_cpm_brg1 { - u32 brgc1; - u32 brgc2; - u32 brgc3; - u32 brgc4; -} ccsr_cpm_brg1_t; - -/* SCC1-SCC4 */ -typedef struct ccsr_cpm_scc { - u32 gsmrl; - u32 gsmrh; - u16 psmr; - u8 res1[2]; - u16 todr; - u16 dsr; - u16 scce; - u8 res2[2]; - u16 sccm; - u8 res3; - u8 sccs; - u8 res4[8]; -} ccsr_cpm_scc_t; - -typedef struct ccsr_cpm_tmp2 { - u8 res[32]; -} ccsr_cpm_tmp2_t; - -/* SPI */ -typedef struct ccsr_cpm_spi { - u16 spmode; - u8 res1[4]; - u8 spie; - u8 res2[3]; - u8 spim; - u8 res3[2]; - u8 spcom; - u8 res4[82]; -} ccsr_cpm_spi_t; - -/* CPM MUX */ -typedef struct ccsr_cpm_mux { - u8 cmxsi1cr; - u8 res1; - u8 cmxsi2cr; - u8 res2; - u32 cmxfcr; - u32 cmxscr; - u8 res3[2]; - u16 cmxuar; - u8 res4[16]; -} ccsr_cpm_mux_t; - -/* SI,MCC,etc */ -typedef struct ccsr_cpm_tmp3 { - u8 res[58592]; -} ccsr_cpm_tmp3_t; - -typedef struct ccsr_cpm_iram { - u32 iram[8192]; - u8 res[98304]; -} ccsr_cpm_iram_t; - -typedef struct ccsr_cpm { - /* Some references are into the unique & known dpram spaces, - * others are from the generic base. - */ -#define im_dprambase im_dpram1 - u8 im_dpram1[16*1024]; - u8 res1[16*1024]; - u8 im_dpram2[16*1024]; - u8 res2[16*1024]; - ccsr_cpm_siu_t im_cpm_siu; /* SIU Configuration */ - ccsr_cpm_intctl_t im_cpm_intctl; /* IRQ Controller */ - ccsr_cpm_iop_t im_cpm_iop; /* IO Port control/status */ - ccsr_cpm_timer_t im_cpm_timer; /* CPM timers */ - ccsr_cpm_sdma_t im_cpm_sdma; /* SDMA control/status */ - ccsr_cpm_fcc1_t im_cpm_fcc1; - ccsr_cpm_fcc2_t im_cpm_fcc2; - ccsr_cpm_fcc3_t im_cpm_fcc3; - ccsr_cpm_fcc1_ext_t im_cpm_fcc1_ext; - ccsr_cpm_fcc2_ext_t im_cpm_fcc2_ext; - ccsr_cpm_fcc3_ext_t im_cpm_fcc3_ext; - ccsr_cpm_tmp1_t im_cpm_tmp1; - ccsr_cpm_brg2_t im_cpm_brg2; - ccsr_cpm_i2c_t im_cpm_i2c; - ccsr_cpm_cp_t im_cpm_cp; - ccsr_cpm_brg1_t im_cpm_brg1; - ccsr_cpm_scc_t im_cpm_scc[4]; - ccsr_cpm_tmp2_t im_cpm_tmp2; - ccsr_cpm_spi_t im_cpm_spi; - ccsr_cpm_mux_t im_cpm_mux; - ccsr_cpm_tmp3_t im_cpm_tmp3; - ccsr_cpm_iram_t im_cpm_iram; -} ccsr_cpm_t; -#endif - #ifdef CONFIG_SYS_SRIO /* Architectural regsiters */ struct rio_arch { @@ -2888,7 +2564,6 @@ struct ccsr_pman { #define CONFIG_SYS_MPC85xx_SERDES1_OFFSET 0xE3000 #define CONFIG_SYS_SEC_MON_OFFSET 0xE6000 #define CONFIG_SYS_SFP_OFFSET 0xE7000 -#define CONFIG_SYS_MPC85xx_CPM_OFFSET 0x80000 #define CONFIG_SYS_FSL_QMAN_OFFSET 0x88000 #define CONFIG_SYS_FSL_BMAN_OFFSET 0x8a000 #define CONFIG_SYS_FSL_FM1_OFFSET 0x100000 @@ -2965,8 +2640,6 @@ struct ccsr_pman { (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_ESDHC_OFFSET) #define CONFIG_SYS_MPC8xxx_PIC_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_PIC_OFFSET) -#define CONFIG_SYS_MPC85xx_CPM_ADDR \ - (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_CPM_OFFSET) #define CONFIG_SYS_MPC85xx_SERDES1_ADDR \ (CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES1_OFFSET) #define CONFIG_SYS_MPC85xx_SERDES2_ADDR \ diff --git a/arch/powerpc/lib/bdinfo.c b/arch/powerpc/lib/bdinfo.c index d2e5e6057b34..55dcad5df8e9 100644 --- a/arch/powerpc/lib/bdinfo.c +++ b/arch/powerpc/lib/bdinfo.c @@ -27,13 +27,6 @@ int arch_setup_bdinfo(void) bd->bi_intfreq = gd->cpu_clk; /* Internal Freq, in Hz */ bd->bi_busfreq = gd->bus_clk; /* Bus Freq, in Hz */ -#if defined(CONFIG_CPM2) - bd->bi_cpmfreq = gd->arch.cpm_clk; - bd->bi_brgfreq = gd->arch.brg_clk; - bd->bi_sccfreq = gd->arch.scc_clk; - bd->bi_vco = gd->arch.vco_out; -#endif /* CONFIG_CPM2 */ - return 0; } @@ -59,10 +52,4 @@ void arch_print_bdinfo(void) puts("addressing = 32-bit\n"); #endif board_detail(); -#if defined(CONFIG_CPM2) - bdinfo_print_mhz("cpmfreq", bd->bi_cpmfreq); - bdinfo_print_mhz("vco", bd->bi_vco); - bdinfo_print_mhz("sccfreq", bd->bi_sccfreq); - bdinfo_print_mhz("brgfreq", bd->bi_brgfreq); -#endif } diff --git a/arch/powerpc/lib/bootm.c b/arch/powerpc/lib/bootm.c index 8d65047aa4d4..3b43066bb4f2 100644 --- a/arch/powerpc/lib/bootm.c +++ b/arch/powerpc/lib/bootm.c @@ -266,12 +266,6 @@ static void set_clocks_in_mhz (struct bd_info *kbd) /* convert all clock information to MHz */ kbd->bi_intfreq /= 1000000L; kbd->bi_busfreq /= 1000000L; -#if defined(CONFIG_CPM2) - kbd->bi_cpmfreq /= 1000000L; - kbd->bi_brgfreq /= 1000000L; - kbd->bi_sccfreq /= 1000000L; - kbd->bi_vco /= 1000000L; -#endif } } diff --git a/drivers/pci/pci_mpc85xx.c b/drivers/pci/pci_mpc85xx.c index 1e180ee289b0..8a81a74067e9 100644 --- a/drivers/pci/pci_mpc85xx.c +++ b/drivers/pci/pci_mpc85xx.c @@ -6,7 +6,6 @@ */ #include <common.h> #include <asm/bitops.h> -#include <asm/cpm_85xx.h> #include <pci.h> #include <dm.h> #include <asm/fsl_law.h> diff --git a/include/asm-generic/u-boot.h b/include/asm-generic/u-boot.h index 637de0c4558a..1becc669aee9 100644 --- a/include/asm-generic/u-boot.h +++ b/include/asm-generic/u-boot.h @@ -52,12 +52,6 @@ struct bd_info { unsigned short bi_ethspeed; /* Ethernet speed in Mbps */ unsigned long bi_intfreq; /* Internal Freq, in MHz */ unsigned long bi_busfreq; /* Bus Freq, in MHz */ -#if defined(CONFIG_CPM2) - unsigned long bi_cpmfreq; /* CPM_CLK Freq, in MHz */ - unsigned long bi_brgfreq; /* BRG_CLK Freq, in MHz */ - unsigned long bi_sccfreq; /* SCC_CLK Freq, in MHz */ - unsigned long bi_vco; /* VCO Out from PLL, in MHz */ -#endif #if defined(CONFIG_M68K) unsigned long bi_pcifreq; /* PCI Bus Freq, in MHz */ #endif diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h deleted file mode 100644 index 57097b17eb16..000000000000 --- a/include/configs/MPC8540ADS.h +++ /dev/null @@ -1,303 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2004, 2011 Freescale Semiconductor. - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao <X.Xiao(a)motorola.com> - */ - -/* - * mpc8540ads board configuration file - * - * Please refer to doc/README.mpc85xx for more info. - * - * Make sure you change the MAC address and other network params first, - * search for CONFIG_SERVERIP, etc in this file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * default CCARBAR is at 0xff700000 - * assume U-Boot is less than 0.5MB - */ - -#ifndef CONFIG_HAS_FEC -#define CONFIG_HAS_FEC 1 /* 8540 has FEC */ -#endif - -/* - * sysclk for MPC85xx - * - * Two valid values are: - * 33000000 - * 66000000 - * - * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz - * is likely the desired value here, so that is now the default. - * The board, however, can run at 66MHz. In any event, this value - * must match the settings of some switches. Details can be found - * in the README.mpc85xxads. - * - * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to - * 33MHz to accommodate, based on a PCI pin. - * Note that PCI-X won't work at 33MHz. - */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* These are used when DDR doesn't use SPD. */ -#define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 -#define CONFIG_SYS_DDR_TIMING_1 0x37344321 -#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ -#define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ -#define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ - -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* - * Local Bus Definitions - */ - -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. - * - * For BR2, need: - * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 - * port-size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 - * - * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into - * FIXME: the top 17 bits of BR2. - */ - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 - */ - -#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ -#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ - -#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \ - | LSDMR_RFCR5 \ - | LSDMR_PRETOACT3 \ - | LSDMR_ACTTORW3 \ - | LSDMR_BL8 \ - | LSDMR_WRC2 \ - | LSDMR_CL3 \ - | LSDMR_RFEN \ - ) - -/* - * SDRAM Controller configuration sequence. - */ -#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) -#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) -#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) - -/* - * 32KB, 8-bit wide for ADS config reg - */ -#define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ - -/* Serial Port */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* - * I2C - */ -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* RapidIO MMU */ -#define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ -#define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */ -#define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000 -#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -#if CONFIG_HAS_FEC -#define CONFIG_MPC85XX_FEC 1 -#define CONFIG_MPC85XX_FEC_NAME "FEC" -#define FEC_PHY_ADDR 3 -#define FEC_PHYIDX 0 -#define FEC_FLAGS 0 -#endif - -/* Options are: TSEC[0-1], FEC */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Miscellaneous configurable options - */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#endif - -#define CONFIG_IPADDR 192.168.1.253 - -#define CONFIG_HOSTNAME "unknown" -#define CONFIG_ROOTPATH "/nfsroot" -#define CONFIG_BOOTFILE "your.uImage" - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=400000\0" \ - "fdtfile=your.fdt.dtb\0" - -#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h deleted file mode 100644 index d23cf0e41aa1..000000000000 --- a/include/configs/MPC8560ADS.h +++ /dev/null @@ -1,292 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright 2004, 2011 Freescale Semiconductor. - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao <X.Xiao(a)motorola.com> - */ - -/* - * mpc8560ads board configuration file - * - * Please refer to doc/README.mpc85xx for more info. - * - * Make sure you change the MAC address and other network params first, - * search for CONFIG_SERVERIP, etc. in this file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <linux/delay.h> - -/* High Level Configuration Options */ -#define CONFIG_CPM2 1 /* has CPM2 */ - -/* - * default CCARBAR is at 0xff700000 - * assume U-Boot is less than 0.5MB - */ - -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -/* - * sysclk for MPC85xx - * - * Two valid values are: - * 33000000 - * 66000000 - * - * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz - * is likely the desired value here, so that is now the default. - * The board, however, can run at 66MHz. In any event, this value - * must match the settings of some switches. Details can be found - * in the README.mpc85xxads. - */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* These are used when DDR doesn't use SPD. */ -#define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 -#define CONFIG_SYS_DDR_TIMING_1 0x37344321 -#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ -#define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ -#define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ - -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* - * Local Bus Definitions - */ - -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. - * - * For BR2, need: - * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 - * port-size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 - * - * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into - * FIXME: the top 17 bits of BR2. - */ - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 - */ - -#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ -#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ - -#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \ - | LSDMR_RFCR5 \ - | LSDMR_PRETOACT3 \ - | LSDMR_ACTTORW3 \ - | LSDMR_BL8 \ - | LSDMR_WRC2 \ - | LSDMR_CL3 \ - | LSDMR_RFEN \ - ) - -/* - * SDRAM Controller configuration sequence. - */ -#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) -#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) -#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) - -/* - * 32KB, 8-bit wide for ADS config reg - */ -#define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ - -/* Serial Port */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -/* - * I2C - */ -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* RapidIO MMU */ -#define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ -#define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */ -#define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000 -#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#if defined(CONFIG_PCI) - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#endif /* CONFIG_PCI */ - -#ifdef CONFIG_TSEC_ENET - -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -/* - * Environment Configuration - */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#define CONFIG_HAS_ETH3 -#endif - -#define CONFIG_IPADDR 192.168.1.253 - -#define CONFIG_HOSTNAME "unknown" -#define CONFIG_ROOTPATH "/nfsroot" -#define CONFIG_BOOTFILE "your.uImage" - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyCPM\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=400000\0" \ - "fdtfile=mpc8560ads.dtb\0" - -#endif /* __CONFIG_H */ -- 2.25.1

4 10

[PATCH] usb: dwc3: Add support to reset usb ULPI phy
by Michal Simek 04 Mar '22

04 Mar '22

From: T Karthik Reddy <t.karthik.reddy(a)xilinx.com> When usb PHY initialization is done, the PHY need to be reset. Signed-off-by: T Karthik Reddy <t.karthik.reddy(a)xilinx.com> Signed-off-by: Michal Simek <michal.simek(a)xilinx.com> --- drivers/usb/dwc3/Kconfig | 2 +- drivers/usb/dwc3/dwc3-generic.c | 28 ++++++++++++++++++++++++++++ 2 files changed, 29 insertions(+), 1 deletion(-) diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig index 62aa65bf0cd2..685bda3729e5 100644 --- a/drivers/usb/dwc3/Kconfig +++ b/drivers/usb/dwc3/Kconfig @@ -25,7 +25,7 @@ config USB_DWC3_OMAP config USB_DWC3_GENERIC bool "Generic implementation of a DWC3 wrapper (aka dwc3 glue)" - depends on DM_USB && USB_DWC3 && MISC + depends on DM_USB && USB_DWC3 && MISC && DM_GPIO help Select this for Xilinx ZynqMP and similar Platforms. This wrapper supports Host and Peripheral operation modes. diff --git a/drivers/usb/dwc3/dwc3-generic.c b/drivers/usb/dwc3/dwc3-generic.c index b1e019b5b91a..17d35a6dc60c 100644 --- a/drivers/usb/dwc3/dwc3-generic.c +++ b/drivers/usb/dwc3/dwc3-generic.c @@ -25,6 +25,7 @@ #include <reset.h> #include <clk.h> #include <usb/xhci.h> +#include <asm/gpio.h> struct dwc3_glue_data { struct clk_bulk clks; @@ -42,6 +43,7 @@ struct dwc3_generic_priv { void *base; struct dwc3 dwc3; struct phy_bulk phys; + struct gpio_desc ulpi_reset; }; struct dwc3_generic_host_priv { @@ -77,6 +79,26 @@ static int dwc3_generic_probe(struct udevice *dev, if (rc && rc != -ENOTSUPP) return rc; + if (device_is_compatible(dev->parent, "xlnx,zynqmp-dwc3")) { + rc = gpio_request_by_name(dev->parent, "reset-gpios", 0, + &priv->ulpi_reset, GPIOD_ACTIVE_LOW); + if (rc != -EBUSY && rc) + return rc; + + /* Toggle ulpi to reset the phy. */ + rc = dm_gpio_set_value(&priv->ulpi_reset, 1); + if (rc) + return rc; + + mdelay(5); + + rc = dm_gpio_set_value(&priv->ulpi_reset, 0); + if (rc) + return rc; + + mdelay(5); + } + if (device_is_compatible(dev->parent, "rockchip,rk3399-dwc3")) reset_deassert_bulk(&glue->resets); @@ -98,6 +120,12 @@ static int dwc3_generic_remove(struct udevice *dev, { struct dwc3 *dwc3 = &priv->dwc3; + if (device_is_compatible(dev->parent, "xlnx,zynqmp-dwc3")) { + struct gpio_desc *ulpi_reset = &priv->ulpi_reset; + + dm_gpio_free(ulpi_reset->dev, ulpi_reset); + } + dwc3_remove(dwc3); dwc3_shutdown_phy(dev, &priv->phys); unmap_physmem(dwc3->regs, MAP_NOCACHE); -- 2.35.1

4 5