August 2021 - U-Boot

status="ok" treated as disabled by DM
by Roger Quadros 20 Aug '21

20 Aug '21

Hi, If the device tree node has status="ok" then the u-boot DM will treat the device as disabled. There are still quite many devices using "ok" instead of "okay" or no status and those devices will not be bound. What is the right fix? 1) make u-boot DM to treat satus="ok" as enabled. 2) fix device tree by changing "ok" to "okay". cheers, -roger

2 2

[PATCH 1/2] imx8mm-cl-iot-gate: Do not build fip.bin by default
by Fabio Estevam 20 Aug '21

20 Aug '21

When trying to build the imx8mm-cl-iot-gate_defconfig target there is a build error due to the missing 'fip.bin'. To make the build process more consistent with other i.MX8M boards, do not build fip.bin by default. Signed-off-by: Fabio Estevam <festevam(a)denx.de> --- arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi | 14 +------------- 1 file changed, 1 insertion(+), 13 deletions(-) diff --git a/arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi b/arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi index 3226a244a97e..00927c157449 100644 --- a/arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi +++ b/arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi @@ -217,18 +217,6 @@ }; }; - fip { - description = "Trusted Firmware FIP"; - type = "firmware"; - arch = "arm64"; - compression = "none"; - load = <0x40310000>; - - fip_blob: blob-ext{ - filename = "fip.bin"; - }; - }; - fdt { description = "NAME"; type = "flat_dt"; @@ -246,7 +234,7 @@ conf { description = "NAME"; firmware = "uboot"; - loadables = "atf", "fip"; + loadables = "atf"; fdt = "fdt"; }; }; -- 2.25.1

5 18

[PATCH] imx8mm-evk: Generate a single bootable flash.bin again
by Fabio Estevam 19 Aug '21

19 Aug '21

After the conversion to binman in commit 8996e6b7c6a1 ("imx8mm_evk: switch to use binman to pack images"), it is necessary to flash both flash.bin and u-boot.itb to get a bootable system. Prior to this commit, only flash.bin was needed. Such new requirement breaks existing distro mechanisms to generate the final binary because the extra u-boot.itb is now required. Generate a final flash.bin that can be used again as a single bootable binary to keep the original behavior. After this change the SPL binary is called spl.bin, which is a more descriptive name for its purpose, and can still be used standalone (for example, for secure boot purposes). Signed-off-by: Fabio Estevam <festevam(a)denx.de> --- arch/arm/dts/imx8mm-evk-u-boot.dtsi | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) diff --git a/arch/arm/dts/imx8mm-evk-u-boot.dtsi b/arch/arm/dts/imx8mm-evk-u-boot.dtsi index f200afac9f..453fe1d259 100644 --- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi +++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi @@ -150,7 +150,7 @@ }; - flash { + spl { mkimage { args = "-n spl/u-boot-spl.cfgout -T imx8mimage -e 0x7e1000"; @@ -217,4 +217,19 @@ }; }; }; + + imx-boot { + filename = "flash.bin"; + pad-byte = <0x00>; + + spl: blob-ext@1 { + offset = <0x0>; + filename = "spl.bin"; + }; + + uboot: blob-ext@2 { + offset = <0x57c00>; + filename = "u-boot.itb"; + }; + }; }; -- 2.25.1

6 8

[PATCH 00/10] xilinx: Add support for DTB reselection
by Michal Simek 19 Aug '21

19 Aug '21

Hi, this series add support for board or board+cc runtime DT selection. EEPROM memory is read and based on that decoded if this is legacy/fru based format and proper DTB is used. There is a need to have all DTBs 64bit aligned. If you don't have it you will end up in exception. But one patch in this series is trying to detect it and panic before you reach it to let you know what's wrong. Enforcing mkimage/dtb alignment is done based on CONFIG_PHYS_64BIT and affects all 64bit systems but it is also not wrong for them to be properly aligned. Thanks, Michal Michal Simek (10): xilinx: fru: Replace spaces with \0 in detected name xilinx: Use variable for passing board_name xilinx: common: Change board_info[] handling xilinx: common: Free allocated structure xilinx: Add support for generic board detection xilinx: zynqmp: Check that DT is 64bit aligned Makefile: Align fit-dtb.blob and u-boot.itb by 64bits for 64bit systems arm64: dts: Make sure that all DTBs are 64bit aligned for 64bit systems xilinx: zynqmp: Generate different u-boot.itb for MULTI_DTB_FIT xilinx: common: Enabling generic function for DT reselection Makefile | 7 ++ arch/arm/dts/Makefile | 4 + arch/arm/dts/zynqmp-sm-k26-revA.dts | 3 + arch/arm/mach-zynqmp/mkimage_fit_atf.sh | 47 +++++++ board/xilinx/common/board.c | 160 +++++++++++++++++++----- board/xilinx/zynqmp/zynqmp.c | 3 + 6 files changed, 194 insertions(+), 30 deletions(-) -- 2.32.0

3 17

A mea culpa undefined reference in v2021.10-rc2, padding_algos, linker lists
by Alex G. 19 Aug '21

19 Aug '21

Hi Simon, I'm seeing an undefined reference to padding_pkcs_15_verify with v2021.10-rc2. It happens when enabling FIT_SIGNATURE. I've tracked it down to the following two commits: commit 92c960bc1d ("lib: rsa: Remove #ifdefs from rsa.h") commit 61416fe9df ("Kconfig: FIT_SIGNATURE should not select RSA_VERIFY") Individually, each commit is fine, but when put together, they cause the issue, as the static inline padding_pkcs_15_verify() implementation is removed from rsa.h. My hypothesis is that moving padding_algos to a linker list will solve this specific problem. I realize you might be working on the same part of the code. Should I address this issue, or should I wait for your series? Alex

2 1

[PATCH 1/2] armv8: Disable pointer authentication traps for EL1
by Peter Hoyes 19 Aug '21

19 Aug '21

From: Peter Hoyes <Peter.Hoyes(a)arm.com> The use of ARMv8.3 pointer authentication (PAuth) is governed by fields in HCR_EL2, which trigger a 'trap to EL2' if not enabled. The reset value of these fields is 'architecturally unknown' so we must ensure that the fields are enabled (to disable the traps) if we are entering the kernel at EL1. The APK field disables PAuth instruction traps and the API field disables PAuth register traps Add code to disable the traps in armv8_switch_to_el1_m. Prior to doing so, it checks fields in the ID_AA64ISAR1_EL1 register to ensure pointer authentication is supported by the hardware. The runtime checks require a second temporary register, so add this to the EL1 transition macro signature and update 2 call sites. Signed-off-by: Peter Hoyes <Peter.Hoyes(a)arm.com> --- arch/arm/cpu/armv8/fsl-layerscape/spintable.S | 2 +- arch/arm/cpu/armv8/transition.S | 2 +- arch/arm/include/asm/macro.h | 11 +++++++++-- arch/arm/include/asm/system.h | 15 +++++++++++++++ 4 files changed, 26 insertions(+), 4 deletions(-) diff --git a/arch/arm/cpu/armv8/fsl-layerscape/spintable.S b/arch/arm/cpu/armv8/fsl-layerscape/spintable.S index 363ded03e6..d6bd188459 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/spintable.S +++ b/arch/arm/cpu/armv8/fsl-layerscape/spintable.S @@ -93,7 +93,7 @@ __secondary_boot_func: 4: #ifdef CONFIG_ARMV8_SWITCH_TO_EL1 switch_el x7, _dead_loop, 0f, _dead_loop -0: armv8_switch_to_el1_m x4, x6, x7 +0: armv8_switch_to_el1_m x4, x6, x7, x9 #else switch_el x7, 0f, _dead_loop, _dead_loop 0: armv8_switch_to_el2_m x4, x6, x7 diff --git a/arch/arm/cpu/armv8/transition.S b/arch/arm/cpu/armv8/transition.S index a31af4ffc8..9dbdff3a4f 100644 --- a/arch/arm/cpu/armv8/transition.S +++ b/arch/arm/cpu/armv8/transition.S @@ -40,7 +40,7 @@ ENTRY(armv8_switch_to_el1) * now, jump to the address saved in x4. */ br x4 -1: armv8_switch_to_el1_m x4, x5, x6 +1: armv8_switch_to_el1_m x4, x5, x6, x7 ENDPROC(armv8_switch_to_el1) .popsection diff --git a/arch/arm/include/asm/macro.h b/arch/arm/include/asm/macro.h index 485310d660..e1eefc283f 100644 --- a/arch/arm/include/asm/macro.h +++ b/arch/arm/include/asm/macro.h @@ -256,7 +256,7 @@ lr .req x30 * For loading 64-bit OS, x0 is physical address to the FDT blob. * They will be passed to the guest. */ -.macro armv8_switch_to_el1_m, ep, flag, tmp +.macro armv8_switch_to_el1_m, ep, flag, tmp, tmp2 /* Initialize Generic Timers */ mrs \tmp, cnthctl_el2 /* Enable EL1 access to timers */ @@ -306,7 +306,14 @@ lr .req x30 b.eq 1f /* Initialize HCR_EL2 */ - ldr \tmp, =(HCR_EL2_RW_AARCH64 | HCR_EL2_HCD_DIS) + /* Only disable PAuth traps if PAuth is supported */ + mrs \tmp, id_aa64isar1_el1 + ldr \tmp2, =(ID_AA64ISAR1_EL1_GPI | ID_AA64ISAR1_EL1_GPA | \ + ID_AA64ISAR1_EL1_API | ID_AA64ISAR1_EL1_APA) + tst \tmp, \tmp2 + mov \tmp2, #(HCR_EL2_RW_AARCH64 | HCR_EL2_HCD_DIS) + orr \tmp, \tmp2, #(HCR_EL2_APK | HCR_EL2_API) + csel \tmp, \tmp2, \tmp, eq msr hcr_el2, \tmp /* Return to the EL1_SP1 mode from EL2 */ diff --git a/arch/arm/include/asm/system.h b/arch/arm/include/asm/system.h index 8b3a54e64c..77aa18909e 100644 --- a/arch/arm/include/asm/system.h +++ b/arch/arm/include/asm/system.h @@ -75,10 +75,25 @@ /* * HCR_EL2 bits definitions */ +#define HCR_EL2_API (1 << 41) /* Trap pointer authentication + instructions */ +#define HCR_EL2_APK (1 << 40) /* Trap pointer authentication + key access */ #define HCR_EL2_RW_AARCH64 (1 << 31) /* EL1 is AArch64 */ #define HCR_EL2_RW_AARCH32 (0 << 31) /* Lower levels are AArch32 */ #define HCR_EL2_HCD_DIS (1 << 29) /* Hypervisor Call disabled */ +/* + * ID_AA64ISAR1_EL1 bits definitions + */ +#define ID_AA64ISAR1_EL1_GPI (0xF << 28) /* Implementation-defined generic + code auth algorithm */ +#define ID_AA64ISAR1_EL1_GPA (0xF << 24) /* QARMA generic code auth + algorithm */ +#define ID_AA64ISAR1_EL1_API (0xF << 8) /* Implementation-defined address + auth algorithm */ +#define ID_AA64ISAR1_EL1_APA (0xF << 4) /* QARMA address auth algorithm */ + /* * ID_AA64PFR0_EL1 bits definitions */ -- 2.25.1

2 1

[PULL] u-boot-riscv/master
by Leo Liang 19 Aug '21

19 Aug '21

Hi Tom, The following changes since commit a0da2dda4ed9d0aee5265e9cd8876734f9f80e09: Prepare v2021.10-rc2 (2021-08-16 14:18:45 -0400) are available in the Git repository at: git@source.denx.de:u-boot/custodians/u-boot-riscv.git for you to fetch changes up to 47d73ba4f4a40f17622d93f96b48e285b73c3061: board: sifive: overwrite board_fdt_blob_setup in u-boot proper (2021-08-17 19:28:37 +0800) CI result shows no issue: https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/8749 ---------------------------------------------------------------- Dimitri John Ledkov (1): qemu-riscv64_smode: fix extlinux (define preboot) Zong Li (3): riscv: cpu: fu740: Fix typo of date board: sifive: compile stuff only related to SPL in SPL build board: sifive: overwrite board_fdt_blob_setup in u-boot proper arch/riscv/cpu/fu740/spl.c | 2 +- board/sifive/unleashed/Makefile | 4 ++-- board/sifive/unleashed/unleashed.c | 11 +++++++++++ board/sifive/unmatched/Makefile | 3 ++- board/sifive/unmatched/unmatched.c | 11 +++++++++++ configs/qemu-riscv64_smode_defconfig | 2 ++ 6 files changed, 29 insertions(+), 4 deletions(-)

2 1

[PATCH v5 00/12] handling all DM watchdogs in watchdog_reset()
by Rasmus Villemoes 19 Aug '21

19 Aug '21

This series is an attempt at expanding the wdt-uclass provided watchdog_reset() to handle all DM watchdogs, not just the first one. Some of the ad hoc work done for the first DM watchdog in initr_watchdog() is now moved to a .pre_probe hook so it is automatically done for all devices. It also includes a patch adding a driver for a gpio-petted watchdog device (and a sandbox test of that) - it is included here because that also gives a relatively easy way to have more than one (kind of) watchdog device in the sandbox, which is then used at the end to test that watchdog_reset() behaves as expected. v2 here: https://lore.kernel.org/u-boot/20210527220017.1266765-1-rasmus.villemoes@pr… v3 here: https://lore.kernel.org/u-boot/20210702124510.124401-1-rasmus.villemoes@pre… v4 here: https://lore.kernel.org/u-boot/20210802150016.588750-1-rasmus.villemoes@pre… Changes in v5: - Handle leftover use of gd->watchdog_dev (new patches 7 and 8). Rasmus Villemoes (12): watchdog: wdt-uclass.c: use wdt_start() in wdt_expire_now() watchdog: wdt-uclass.c: introduce struct wdt_priv watchdog: wdt-uclass.c: neaten UCLASS_DRIVER definition watchdog: wdt-uclass.c: refactor initr_watchdog() watchdog: wdt-uclass.c: keep track of each device's running state sandbox: disable CONFIG_WATCHDOG_AUTOSTART watchdog: wdt-uclass.c: add wdt_stop_all() helper board: x530: switch to wdt_stop_all() watchdog: wdt-uclass.c: handle all DM watchdogs in watchdog_reset() watchdog: add gpio watchdog driver sandbox: add test of wdt_gpio driver sandbox: add test of wdt-uclass' watchdog_reset() arch/sandbox/dts/test.dts | 8 + board/alliedtelesis/x530/x530.c | 5 +- configs/sandbox64_defconfig | 2 + configs/sandbox_defconfig | 2 + .../watchdog/gpio-wdt.txt | 19 ++ drivers/watchdog/Kconfig | 9 + drivers/watchdog/Makefile | 1 + drivers/watchdog/gpio_wdt.c | 68 +++++++ drivers/watchdog/wdt-uclass.c | 192 +++++++++++++----- include/asm-generic/global_data.h | 6 - include/wdt.h | 5 + test/dm/wdt.c | 90 +++++++- 12 files changed, 346 insertions(+), 61 deletions(-) create mode 100644 doc/device-tree-bindings/watchdog/gpio-wdt.txt create mode 100644 drivers/watchdog/gpio_wdt.c -- 2.31.1

3 16

[PATCH v4 1/2] imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards (N63xx/N64xx)
by Frieder Schrempf 19 Aug '21

19 Aug '21

From: Frieder Schrempf <frieder.schrempf(a)kontron.de> This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by Kontron Electronics GmbH. Currently there are the following SoM flavors (SoM-Line): * N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND * N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND * N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND And the according evaluation boards (Board-Line): * N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ... * N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ... * N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ... Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config options at compile-time. Though the differences are so minor, that for the scope of these SoMs we just use a single defconfig that is compatible with both SoCs. Signed-off-by: Frieder Schrempf <frieder.schrempf(a)kontron.de> Reviewed-by: Stefano Babic <sbabic(a)denx.de> --- Fixes in v4: * Fix checkpatch errors/warnings * Stop disabling initrd/fdt relocation Fixes in v3: * Guard binman nodes to fix build of other UL boards Fixes in v2: * Add MAINTAINERS file * Rename board directory * Use binman to generate FIT * Support legacy images * Add Stefano's R-b tag --- arch/arm/dts/Makefile | 4 +- .../dts/imx6ul-kontron-n631x-s-u-boot.dtsi | 7 + arch/arm/dts/imx6ul-kontron-n631x-s.dts | 17 + arch/arm/dts/imx6ul-kontron-n631x-som.dtsi | 14 + .../dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi | 98 ++++ arch/arm/dts/imx6ul-kontron-n6x1x-s.dts | 423 ++++++++++++++++++ arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi | 420 +++++++++++++++++ .../dts/imx6ul-kontron-n6x1x-som-common.dtsi | 124 +++++ .../dts/imx6ull-kontron-n641x-s-u-boot.dtsi | 7 + arch/arm/dts/imx6ull-kontron-n641x-s.dts | 16 + arch/arm/dts/imx6ull-kontron-n641x-som.dtsi | 13 + arch/arm/mach-imx/mx6/Kconfig | 9 + board/kontron/sl-mx6ul/Kconfig | 15 + board/kontron/sl-mx6ul/MAINTAINERS | 9 + board/kontron/sl-mx6ul/Makefile | 8 + board/kontron/sl-mx6ul/kontron_mx6ul.c | 85 ++++ board/kontron/sl-mx6ul/spl.c | 377 ++++++++++++++++ configs/kontron_mx6ul_defconfig | 109 +++++ include/configs/kontron_common.h | 84 ++++ include/configs/kontron_mx6ul.h | 52 +++ 20 files changed, 1890 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi create mode 100644 arch/arm/dts/imx6ul-kontron-n631x-s.dts create mode 100644 arch/arm/dts/imx6ul-kontron-n631x-som.dtsi create mode 100644 arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi create mode 100644 arch/arm/dts/imx6ul-kontron-n6x1x-s.dts create mode 100644 arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi create mode 100644 arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi create mode 100644 arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi create mode 100644 arch/arm/dts/imx6ull-kontron-n641x-s.dts create mode 100644 arch/arm/dts/imx6ull-kontron-n641x-som.dtsi create mode 100644 board/kontron/sl-mx6ul/Kconfig create mode 100644 board/kontron/sl-mx6ul/MAINTAINERS create mode 100644 board/kontron/sl-mx6ul/Makefile create mode 100644 board/kontron/sl-mx6ul/kontron_mx6ul.c create mode 100644 board/kontron/sl-mx6ul/spl.c create mode 100644 configs/kontron_mx6ul_defconfig create mode 100644 include/configs/kontron_common.h create mode 100644 include/configs/kontron_mx6ul.h diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 91228b7032..b2b0e50dc5 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -811,7 +811,9 @@ dtb-$(CONFIG_MX6UL) += \ imx6ul-liteboard.dtb \ imx6ul-phytec-segin-ff-rdk-nand.dtb \ imx6ul-pico-hobbit.dtb \ - imx6ul-pico-pi.dtb + imx6ul-pico-pi.dtb \ + imx6ul-kontron-n631x-s.dtb \ + imx6ull-kontron-n641x-s.dtb dtb-$(CONFIG_MX6ULL) += \ imx6ull-14x14-evk.dtb \ diff --git a/arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi b/arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi new file mode 100644 index 0000000000..d3f013c58c --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n631x-s-u-boot.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi" diff --git a/arch/arm/dts/imx6ul-kontron-n631x-s.dts b/arch/arm/dts/imx6ul-kontron-n631x-s.dts new file mode 100644 index 0000000000..407d2b1dab --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n631x-s.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk(a)kernel.org> + */ + +/dts-v1/; + +#include "imx6ul-kontron-n631x-som.dtsi" +#include "imx6ul-kontron-n6x1x-s.dtsi" + +/ { + model = "Kontron N631X S"; + compatible = "kontron,imx6ul-n631x-s", "kontron,imx6ul-n631x-som", + "fsl,imx6ul"; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n631x-som.dtsi b/arch/arm/dts/imx6ul-kontron-n631x-som.dtsi new file mode 100644 index 0000000000..9a1179814b --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n631x-som.dtsi @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk(a)kernel.org> + */ + +#include "imx6ul.dtsi" +#include "imx6ul-kontron-n6x1x-som-common.dtsi" + +/ { + model = "Kontron N631X SOM"; + compatible = "kontron,imx6ul-n631x-som", "fsl,imx6ul"; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi b/arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi new file mode 100644 index 0000000000..17880d0dd9 --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-s-u-boot.dtsi @@ -0,0 +1,98 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#if defined(CONFIG_FIT) + +/ { + binman: binman { + multiple-images; + }; +}; + +&binman { + itb { + filename = "u-boot.itb"; + + fit { + description = "Configuration to load U-Boot"; + #address-cells = <1>; + fit,external-offset = <CONFIG_FIT_EXTERNAL_OFFSET>; + + images { + uboot { + description = "U-Boot"; + type = "standalone"; + arch = "arm"; + compression = "none"; + load = <CONFIG_SYS_TEXT_BASE>; + + uboot_blob: blob-ext { + filename = "u-boot-nodtb.bin"; + }; + }; + + fdt { + description = "NAME"; + type = "flat_dt"; + compression = "none"; + + uboot_fdt_blob: blob-ext { + filename = "u-boot.dtb"; + }; + }; + }; + + configurations { + default = "conf"; + + conf { + description = "NAME"; + firmware = "uboot"; + fdt = "fdt"; + }; + }; + }; + }; +}; + +#endif /* CONFIG_FIT */ + +/* + * To make the PHYs work, we need to set the reset pin once. Afterwards + * in Linux we can't assign the shared reset GPIO to the PHYs, as this + * would cause Linux to reset both PHYs every time one of them gets + * reinitialized. + * + * Also we disable the second ethernet as it currently doesn't work with + * the devicetree setup in U-Boot. + */ + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>; + phy-mode = "rmii"; + phy-handle = <&ethphy1>; + phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&fec2 { + status = "disabled"; + /delete-property/ phy-handle; + /delete-node/ mdio; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-s.dts b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dts new file mode 100644 index 0000000000..84d8a717ab --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dts @@ -0,0 +1,423 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk(a)kernel.org> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include "imx6ul-kontron-n6x1x-som.dtsi" + +/ { + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led1 { + label = "debug-led1"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led2 { + label = "debug-led2"; + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led3 { + label = "debug-led3"; + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&pwm8 0 5000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vref_adc: regulator-vref-adc { + compatible = "regulator-fixed"; + regulator-name = "vref-adc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + num-channels = <3>; + vref-supply = <&reg_vref_adc>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + eeprom@0 { + compatible = "anvo,anv32e61w", "atmel,at25"; + reg = <0>; + spi-max-frequency = <20000000>; + spi-cpha; + spi-cpol; + pagesize = <1>; + size = <8192>; + address-width = <16>; + }; +}; + +&fec1 { + pinctrl-0 = <&pinctrl_enet1>; + /delete-node/ mdio; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>; + phy-mode = "rmii"; + phy-handle = <&ethphy2>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; +}; + +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm8>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + rs485-rx-during-tx; + rs485-rts-active-low; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + over-current-active-low; + vbus-supply = <&reg_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + vbus-supply = <&reg_5v>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <&reg_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + non-removable; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <&reg_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; + + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1 + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */ + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009 + >; + }; + + pinctrl_enet2_mdio: enet2mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_gpio: gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */ + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */ + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */ + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */ + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0 + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0 + >; + }; + + pinctrl_pwm8: pwm8grp { + fsl,pins = < + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1 + /* + * mux unused RTS to make sure it doesn't cause + * any interrupts when it is undefined + */ + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1 + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1 + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usbotg1: usbotg1 { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi new file mode 100644 index 0000000000..4682a79f5b --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-s.dtsi @@ -0,0 +1,420 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk(a)kernel.org> + */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led1 { + label = "debug-led1"; + gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "heartbeat"; + }; + + led2 { + label = "debug-led2"; + gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led3 { + label = "debug-led3"; + gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + pwm-beeper { + compatible = "pwm-beeper"; + pwms = <&pwm8 0 5000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vref_adc: regulator-vref-adc { + compatible = "regulator-fixed"; + regulator-name = "vref-adc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&adc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc1>; + num-channels = <3>; + vref-supply = <&reg_vref_adc>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + eeprom@0 { + compatible = "anvo,anv32e61w", "atmel,at25"; + reg = <0>; + spi-max-frequency = <20000000>; + spi-cpha; + spi-cpol; + pagesize = <1>; + size = <8192>; + address-width = <16>; + }; +}; + +&fec1 { + pinctrl-0 = <&pinctrl_enet1>; + /delete-node/ mdio; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>; + phy-mode = "rmii"; + phy-handle = <&ethphy2>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET2_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; +}; + +&pwm8 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm8>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + linux,rs485-enabled-at-boot-time; + rs485-rx-during-tx; + rs485-rts-active-low; + uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + dr_mode = "otg"; + srp-disable; + hnp-disable; + adp-disable; + over-current-active-low; + vbus-supply = <&reg_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + disable-over-current; + vbus-supply = <&reg_5v>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <&reg_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + non-removable; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <&reg_3v3>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + no-1-8-v; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>; + + pinctrl_adc1: adc1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0 + MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0 + MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1 + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */ + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0 + MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0 + MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0 + MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0 + MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009 + >; + }; + + pinctrl_enet2_mdio: enet2mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp{ + fsl,pins = < + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020 + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020 + >; + }; + + pinctrl_gpio: gpiogrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */ + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */ + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */ + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */ + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0 + MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0 + >; + }; + + pinctrl_pwm8: pwm8grp { + fsl,pins = < + MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1 + MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1 + MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1 + /* + * mux unused RTS to make sure it doesn't cause + * any interrupts when it is undefined + */ + MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1 + MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1 + MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1 + MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1 + MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usbotg1: usbotg1 { + fsl,pins = < + MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059 + MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */ + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi new file mode 100644 index 0000000000..e9ec6b7891 --- /dev/null +++ b/arch/arm/dts/imx6ul-kontron-n6x1x-som-common.dtsi @@ -0,0 +1,124 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + * Copyright (c) 2019 Krzysztof Kozlowski <krzk(a)kernel.org> + */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + chosen { + stdout-path = &uart4; + }; + + memory@80000000 { + reg = <0x80000000 0x10000000>; + device_type = "memory"; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + spi-flash@0 { + compatible = "mxicy,mx25v8035f", "jedec,spi-nor"; + spi-max-frequency = <50000000>; + reg = <0>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>; + phy-mode = "rmii"; + phy-handle = <&ethphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + reg = <1>; + micrel,led-mode = <0>; + clocks = <&clks IMX6UL_CLK_ENET_REF>; + clock-names = "rmii-ref"; + }; + }; +}; + +&fec2 { + phy-mode = "rmii"; + status = "disabled"; +}; + +&qspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_qspi>; + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + spi-max-frequency = <104000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + reg = <0>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reset_out>; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1 + MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1 + MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1 + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009 + >; + }; + + pinctrl_enet1_mdio: enet1mdiogrp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0 + >; + }; + + pinctrl_qspi: qspigrp { + fsl,pins = < + MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1 + MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1 + MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1 + MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1 + MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1 + MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1 + >; + }; + + pinctrl_reset_out: rstoutgrp { + fsl,pins = < + MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0 + >; + }; +}; diff --git a/arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi b/arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi new file mode 100644 index 0000000000..d3f013c58c --- /dev/null +++ b/arch/arm/dts/imx6ull-kontron-n641x-s-u-boot.dtsi @@ -0,0 +1,7 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi" diff --git a/arch/arm/dts/imx6ull-kontron-n641x-s.dts b/arch/arm/dts/imx6ull-kontron-n641x-s.dts new file mode 100644 index 0000000000..01aeea4085 --- /dev/null +++ b/arch/arm/dts/imx6ull-kontron-n641x-s.dts @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2019 Kontron Electronics GmbH + */ + +/dts-v1/; + +#include "imx6ull-kontron-n641x-som.dtsi" +#include "imx6ul-kontron-n6x1x-s.dtsi" + +/ { + model = "Kontron N641X S"; + compatible = "kontron,imx6ull-n641x-s", "kontron,imx6ull-n641x-som", + "fsl,imx6ull"; +}; diff --git a/arch/arm/dts/imx6ull-kontron-n641x-som.dtsi b/arch/arm/dts/imx6ull-kontron-n641x-som.dtsi new file mode 100644 index 0000000000..8a64aa9a27 --- /dev/null +++ b/arch/arm/dts/imx6ull-kontron-n641x-som.dtsi @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2017 exceet electronics GmbH + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include "imx6ull.dtsi" +#include "imx6ul-kontron-n6x1x-som-common.dtsi" + +/ { + model = "Kontron N641X SOM"; + compatible = "kontron,imx6ull-n641x-som", "fsl,imx6ull"; +}; diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig index 23cab3932b..abf28915f8 100644 --- a/arch/arm/mach-imx/mx6/Kconfig +++ b/arch/arm/mach-imx/mx6/Kconfig @@ -231,6 +231,14 @@ config TARGET_GW_VENTANA imply CMD_SATA imply CMD_SPL +config TARGET_KONTRON_MX6UL + bool "Kontron Electronics SL/BL i.MX6UL/ULL (N63xx/N64xx)" + depends on MX6UL + select DM + select DM_THERMAL + select SUPPORT_SPL + imply CMD_DM + config TARGET_KOSAGI_NOVENA bool "Kosagi Novena" select BOARD_LATE_INIT @@ -671,6 +679,7 @@ source "board/grinn/liteboard/Kconfig" source "board/phytec/pcm058/Kconfig" source "board/phytec/pcl063/Kconfig" source "board/gateworks/gw_ventana/Kconfig" +source "board/kontron/sl-mx6ul/Kconfig" source "board/kosagi/novena/Kconfig" source "board/softing/vining_2000/Kconfig" source "board/liebherr/display5/Kconfig" diff --git a/board/kontron/sl-mx6ul/Kconfig b/board/kontron/sl-mx6ul/Kconfig new file mode 100644 index 0000000000..fd3a8936f0 --- /dev/null +++ b/board/kontron/sl-mx6ul/Kconfig @@ -0,0 +1,15 @@ +if TARGET_KONTRON_MX6UL + +config SYS_BOARD + string + default "sl-mx6ul" + +config SYS_VENDOR + string + default "kontron" + +config SYS_CONFIG_NAME + string + default "kontron_mx6ul" + +endif diff --git a/board/kontron/sl-mx6ul/MAINTAINERS b/board/kontron/sl-mx6ul/MAINTAINERS new file mode 100644 index 0000000000..d5b1d402cc --- /dev/null +++ b/board/kontron/sl-mx6ul/MAINTAINERS @@ -0,0 +1,9 @@ +Kontron SL/BL i.MX6UL/ULL Boards (N63xx/N64xx) +M: Frieder Schrempf <frieder.schrempf(a)kontron.de> +S: Maintained +F: arch/arm/dts/imx6ul-kontron-n631x- +F: arch/arm/dts/imx6ul-kontron-n6x1x- +F: arch/arm/dts/imx6ull-kontron-n641x- +F: board/kontron/sl-mx6ul +F: configs/kontron_mx6ul_defconfig +F: include/configs/kontron_mx6ul.h diff --git a/board/kontron/sl-mx6ul/Makefile b/board/kontron/sl-mx6ul/Makefile new file mode 100644 index 0000000000..f90eb11f76 --- /dev/null +++ b/board/kontron/sl-mx6ul/Makefile @@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0+ +# (C) Copyright 2018 Kontron Electronics GmbH + +ifdef CONFIG_SPL_BUILD +obj-y := spl.o +else +obj-y := kontron_mx6ul.o +endif diff --git a/board/kontron/sl-mx6ul/kontron_mx6ul.c b/board/kontron/sl-mx6ul/kontron_mx6ul.c new file mode 100644 index 0000000000..79d4d8753b --- /dev/null +++ b/board/kontron/sl-mx6ul/kontron_mx6ul.c @@ -0,0 +1,85 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include <asm/arch/clock.h> +#include <asm/arch/sys_proto.h> +#include <asm/global_data.h> +#include <fdt_support.h> +#include <phy.h> + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + gd->ram_size = imx_ddr_size(); + + return 0; +} + +int ft_board_setup(void *blob, struct bd_info *bd) +{ + /* + * Overwrite the memory size in the devicetree that is + * passed to the kernel with the actual size detected. + */ + return fdt_fixup_memory(blob, PHYS_SDRAM, gd->ram_size); +} + +static int setup_fec(void) +{ + struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; + int ret; + + /* + * Use 50M anatop loopback REF_CLK1 for ENET1, + * clear gpr1[13], set gpr1[17]. + */ + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, + IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK); + + /* + * Use 50M anatop loopback REF_CLK2 for ENET2, + * clear gpr1[14], set gpr1[18]. + */ + clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK, + IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK); + + ret = enable_fec_anatop_clock(0, ENET_50MHZ); + if (ret) + return ret; + + ret = enable_fec_anatop_clock(1, ENET_50MHZ); + if (ret) + return ret; + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +int board_early_init_f(void) +{ + enable_qspi_clk(0); + + return 0; +} + +int board_init(void) +{ + /* Address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + setup_fec(); + + return 0; +} diff --git a/board/kontron/sl-mx6ul/spl.c b/board/kontron/sl-mx6ul/spl.c new file mode 100644 index 0000000000..57760981c5 --- /dev/null +++ b/board/kontron/sl-mx6ul/spl.c @@ -0,0 +1,377 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + */ + +#include <asm/arch/clock.h> +#include <asm/arch/crm_regs.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/global_data.h> +#include <asm/gpio.h> +#include <asm/io.h> +#include <asm/mach-imx/iomux-v3.h> +#include <fsl_esdhc_imx.h> +#include <init.h> +#include <linux/delay.h> +#include <linux/sizes.h> +#include <linux/errno.h> +#include <mmc.h> + +DECLARE_GLOBAL_DATA_PTR; + +enum { + BOARD_TYPE_KTN_N631X = 1, + BOARD_TYPE_KTN_N641X, + BOARD_TYPE_MAX +}; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_CD_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) + +#include <spl.h> +#include <asm/arch/mx6-ddr.h> + +static iomux_v3_cfg_t const usdhc1_pads[] = { + MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + + /* CD */ + MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(USDHC_CD_PAD_CTRL), +}; + +#define USDHC1_CD_GPIO IMX_GPIO_NR(1, 19) + +static iomux_v3_cfg_t const usdhc2_pads[] = { + MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + /* RST */ + MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +#define USDHC2_PWR_GPIO IMX_GPIO_NR(4, 10) + +static struct fsl_esdhc_cfg usdhc_cfg[2] = { + {USDHC1_BASE_ADDR, 0, 4}, + {USDHC2_BASE_ADDR, 0, 4}, +}; + +int board_mmc_getcd(struct mmc *mmc) +{ + struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; + + switch (cfg->esdhc_base) { + case USDHC1_BASE_ADDR: + ret = !gpio_get_value(USDHC1_CD_GPIO); + break; + case USDHC2_BASE_ADDR: + // This SDHC interface does not use a CD pin + ret = 1; + break; + } + + return ret; +} + +int board_mmc_init(struct bd_info *bis) +{ + int i, ret; + + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * mmc0 USDHC1 + * mmc1 USDHC2 + */ + for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { + switch (i) { + case 0: + imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); + gpio_direction_input(USDHC1_CD_GPIO); + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); + break; + case 1: + imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + gpio_direction_output(USDHC2_PWR_GPIO, 0); + udelay(500); + gpio_direction_output(USDHC2_PWR_GPIO, 1); + usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + break; + default: + printf("Warning: you configured more USDHC controllers (%d) than supported by the board\n", + i + 1); + return -EINVAL; + } + + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize mmc dev %d\n", i); + return ret; + } + } + return 0; +} + +iomux_v3_cfg_t const ecspi2_pads[] = { + MX6_PAD_CSI_DATA00__ECSPI2_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_CSI_DATA02__ECSPI2_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_CSI_DATA03__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), + MX6_PAD_CSI_DATA01__GPIO4_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +int board_spi_cs_gpio(unsigned int bus, unsigned int cs) +{ + return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS) + ? (IMX_GPIO_NR(4, 22)) : -1; +} + +static void setup_spi(void) +{ + gpio_request(IMX_GPIO_NR(4, 22), "spi2_cs0"); + gpio_direction_output(IMX_GPIO_NR(4, 22), 1); + imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads)); + + enable_spi_clk(true, 1); +} + +static iomux_v3_cfg_t const uart4_pads[] = { + MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); +} + +// DDR 256MB (Hynix H5TQ2G63DFR) +static struct mx6_ddr3_cfg mem_256M_ddr = { + .mem_speed = 800, + .density = 2, + .width = 16, + .banks = 8, + .rowaddr = 14, + .coladdr = 10, + .pagesz = 2, + .trcd = 1350, + .trcmin = 4950, + .trasmin = 3600, +}; + +static struct mx6_mmdc_calibration mx6_mmcd_256M_calib = { + .p0_mpwldectrl0 = 0x00000000, + .p0_mpdgctrl0 = 0x01340134, + .p0_mprddlctl = 0x40405052, + .p0_mpwrdlctl = 0x40404E48, +}; + +// DDR 512MB (Hynix H5TQ4G63DFR) +static struct mx6_ddr3_cfg mem_512M_ddr = { + .mem_speed = 800, + .density = 4, + .width = 16, + .banks = 8, + .rowaddr = 15, + .coladdr = 10, + .pagesz = 2, + .trcd = 1350, + .trcmin = 4950, + .trasmin = 3600, +}; + +static struct mx6_mmdc_calibration mx6_mmcd_512M_calib = { + .p0_mpwldectrl0 = 0x00000000, + .p0_mpdgctrl0 = 0X01440144, + .p0_mprddlctl = 0x40405454, + .p0_mpwrdlctl = 0x40404E4C, +}; + +// Common DDR parameters (256MB and 512MB) +static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = { + .grp_addds = 0x00000028, + .grp_ddrmode_ctl = 0x00020000, + .grp_b0ds = 0x00000028, + .grp_ctlds = 0x00000028, + .grp_b1ds = 0x00000028, + .grp_ddrpke = 0x00000000, + .grp_ddrmode = 0x00020000, + .grp_ddr_type = 0x000c0000, +}; + +static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = { + .dram_dqm0 = 0x00000028, + .dram_dqm1 = 0x00000028, + .dram_ras = 0x00000028, + .dram_cas = 0x00000028, + .dram_odt0 = 0x00000028, + .dram_odt1 = 0x00000028, + .dram_sdba2 = 0x00000000, + .dram_sdclk_0 = 0x00000028, + .dram_sdqs0 = 0x00000028, + .dram_sdqs1 = 0x00000028, + .dram_reset = 0x00000028, +}; + +struct mx6_ddr_sysinfo ddr_sysinfo = { + .dsize = 0, + .cs_density = 20, + .ncs = 1, + .cs1_mirror = 0, + .rtt_wr = 2, + .rtt_nom = 1, /* RTT_Nom = RZQ/2 */ + .walat = 1, /* Write additional latency */ + .ralat = 5, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ + .ddr_type = DDR_TYPE_DDR3, + .refsel = 0, /* Refresh cycles at 64KHz */ + .refr = 1, /* 2 refresh commands per refresh cycle */ +}; + +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0xFFFFFFFF, &ccm->CCGR0); + writel(0xFFFFFFFF, &ccm->CCGR1); + writel(0xFFFFFFFF, &ccm->CCGR2); + writel(0xFFFFFFFF, &ccm->CCGR3); + writel(0xFFFFFFFF, &ccm->CCGR4); + writel(0xFFFFFFFF, &ccm->CCGR5); + writel(0xFFFFFFFF, &ccm->CCGR6); + writel(0xFFFFFFFF, &ccm->CCGR7); +} + +static void spl_dram_init(void) +{ + unsigned int size; + + // DDR RAM connection is always 16 bit wide. Init IOs. + mx6ul_dram_iocfg(16, &mx6_ddr_ioregs, &mx6_grp_ioregs); + + // Try to detect the 512MB RAM chip first. + mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_512M_calib, &mem_512M_ddr); + + // Get the available RAM size + size = get_ram_size((void *)PHYS_SDRAM, SZ_512M); + + gd->ram_size = size; + + if (size == SZ_512M) { + // 512MB RAM was detected + return; + } else if (size == SZ_256M) { + // 256MB RAM was detected, use correct config and calibration + mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_256M_calib, &mem_256M_ddr); + } else { + printf("Invalid DDR RAM size detected: %x\n", size); + } +} + +int do_board_detect(void) +{ + if (is_mx6ul()) + gd->board_type = BOARD_TYPE_KTN_N631X; + else if (is_mx6ull()) + gd->board_type = BOARD_TYPE_KTN_N641X; + + printf("Kontron SL i.MX6UL%s (N6%s1x) module, %lu MB RAM detected\n", + is_mx6ull() ? "L" : "", is_mx6ull() ? "4" : "3", gd->ram_size / SZ_1M); + + return 0; +} + +void board_init_f(ulong dummy) +{ + ccgr_init(); + + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + /* iomux and setup of UART and SPI */ + board_early_init_f(); + + /* setup GP timer */ + timer_init(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + /* DDR initialization */ + spl_dram_init(); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + /* Detect the board type */ + do_board_detect(); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} + +void board_boot_order(u32 *spl_boot_list) +{ + u32 bootdev = spl_boot_device(); + + /* + * The default boot fuse settings use the SD card (MMC1) as primary + * boot device, but allow SPI NOR as a fallback boot device. + * We can't detect the fallback case and spl_boot_device() will return + * BOOT_DEVICE_MMC1 despite the actual boot device being SPI NOR. + * Therefore we try to load U-Boot proper vom SPI NOR after loading + * from MMC has failed. + */ + spl_boot_list[0] = bootdev; + + switch (bootdev) { + case BOOT_DEVICE_MMC1: + case BOOT_DEVICE_MMC2: + spl_boot_list[1] = BOOT_DEVICE_SPI; + break; + } +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + setup_spi(); + + return 0; +} + +int board_fit_config_name_match(const char *name) +{ + if (gd->board_type == BOARD_TYPE_KTN_N631X && is_mx6ul() && + !strcmp(name, "imx6ul-kontron-n631x-s")) + return 0; + + if (gd->board_type == BOARD_TYPE_KTN_N641X && is_mx6ull() && + !strcmp(name, "imx6ull-kontron-n641x-s")) + return 0; + + return -1; +} diff --git a/configs/kontron_mx6ul_defconfig b/configs/kontron_mx6ul_defconfig new file mode 100644 index 0000000000..5a9a211d32 --- /dev/null +++ b/configs/kontron_mx6ul_defconfig @@ -0,0 +1,109 @@ +CONFIG_ARM=y +CONFIG_ARCH_MX6=y +CONFIG_SYS_TEXT_BASE=0x87800000 +CONFIG_SPL_GPIO_SUPPORT=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=1 +CONFIG_SYS_MEMTEST_START=0x80000000 +CONFIG_SYS_MEMTEST_END=0x90000000 +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0xF0000 +CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_SYS_SPI_U_BOOT_OFFS=0x20000 +CONFIG_MX6UL=y +CONFIG_TARGET_KONTRON_MX6UL=y +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx6ul-kontron-n631x-s" +CONFIG_SPL_TEXT_BASE=0x00908000 +CONFIG_SPL_MMC_SUPPORT=y +CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_BOOTCOUNT_BOOTLIMIT=3 +CONFIG_SPL=y +CONFIG_SPL_SPI_FLASH_SUPPORT=y +CONFIG_SPL_SPI_SUPPORT=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_FIT=y +CONFIG_SPL_LOAD_FIT=y +# CONFIG_USE_SPL_FIT_GENERATOR is not set +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg" +CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_BOARD_TYPES=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_SPL_RAW_IMAGE_SUPPORT=y +CONFIG_SPL_LEGACY_IMAGE_SUPPORT=y +CONFIG_SPL_LEGACY_IMAGE_CRC_CHECK=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8A +CONFIG_SPL_SPI_LOAD=y +CONFIG_SPL_USB_HOST_SUPPORT=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_MTD=y +CONFIG_CMD_SF_TEST=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_CMD_FS_UUID=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nor0=spi1.0,spi-nand0=spi4.0" +CONFIG_MTDPARTS_DEFAULT="mtdparts=spi1.0:128k(spl),832k(u-boot),64k(env);spi4.0:-(UBI)" +CONFIG_CMD_UBI=y +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_OF_LIST="imx6ul-kontron-n631x-s imx6ull-kontron-n641x-s" +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_USE_ENV_SPI_BUS=y +CONFIG_ENV_SPI_BUS=2 +CONFIG_BOOTCOUNT_LIMIT=y +CONFIG_BOOTCOUNT_ENV=y +CONFIG_DM_I2C=y +CONFIG_FSL_USDHC=y +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_MTD_SPI_NAND=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SF_DEFAULT_BUS=1 +CONFIG_SF_DEFAULT_MODE=0 +CONFIG_SF_DEFAULT_SPEED=10000000 +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_SPI_FLASH_MTD=y +CONFIG_PHYLIB=y +CONFIG_PHY_MICREL=y +CONFIG_PHY_MICREL_KSZ8XXX=y +CONFIG_DM_ETH=y +CONFIG_DM_ETH_PHY=y +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX6=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_CONS_INDEX=4 +CONFIG_MXC_UART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_FSL_QSPI=y +CONFIG_MXC_SPI=y +CONFIG_IMX_THERMAL=y +CONFIG_USB=y +CONFIG_DM_USB=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_FDT_FIXUP_PARTITIONS=y diff --git a/include/configs/kontron_common.h b/include/configs/kontron_common.h new file mode 100644 index 0000000000..d549e9f07c --- /dev/null +++ b/include/configs/kontron_common.h @@ -0,0 +1,84 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + * + * Common configuration settings for the Kontron Electronics boards. + * + */ + +#ifndef __KONTRON_COMMON_CONFIG_H +#define __KONTRON_COMMON_CONFIG_H + +#include <asm/arch/imx-regs.h> +#include <asm/mach-imx/gpio.h> +#include <linux/sizes.h> + +#ifdef CONFIG_MX6 +#include "mx6_common.h" +#ifdef CONFIG_SPL_BUILD +#include "imx6_spl.h" +#endif +#endif + +/* + * ####################################### + * ### MISC ### + * ####################################### + */ +#define CONFIG_SYS_MALLOC_LEN SZ_64M +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* + * ####################################### + * ### Ethernet ### + * ####################################### + */ +#ifdef CONFIG_FEC_MXC +#define CONFIG_ETHPRIME "eth0" +#else +#define CONFIG_ETHPRIME +#endif + +/* + * ####################################### + * ### USB ### + * ####################################### + */ +#ifdef CONFIG_USB_EHCI_HCD +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 +#endif + +/* + * ####################################### + * ### ENVIRONMENT ### + * ####################################### + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootargs_base=" KONTRON_ENV_KERNEL_MTDPARTS "\0" \ + "script=boot.scr\0" \ + "kernel_addr_r=" KONTRON_ENV_KERNEL_ADDR "\0" \ + "fdt_addr_r=" KONTRON_ENV_FDT_ADDR "\0" \ + "ramdisk_addr_r=" KONTRON_ENV_RAMDISK_ADDR "\0" \ + "pxefile_addr_r=" KONTRON_ENV_PXE_ADDR "\0" \ + "scriptaddr=" KONTRON_ENV_PXE_ADDR "\0" \ + "bootdir=\0" \ + "bootdelay=3\0" \ + "ipaddr=192.168.1.11\0" \ + "serverip=192.168.1.10\0" \ + "gatewayip=192.168.1.10\0" \ + "netmask=255.255.255.0\0" \ + "ethact=" CONFIG_ETHPRIME "\0" \ + "hostname=" CONFIG_HOSTNAME "\0" \ + "bootubipart=spi-nand0\0" \ + "bootubivol=boot\0" \ + BOOTENV + +#endif /* __KONTRON_COMMON_CONFIG_H */ diff --git a/include/configs/kontron_mx6ul.h b/include/configs/kontron_mx6ul.h new file mode 100644 index 0000000000..1295511747 --- /dev/null +++ b/include/configs/kontron_mx6ul.h @@ -0,0 +1,52 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2018 Kontron Electronics GmbH + * + * Configuration settings for the Kontron i.MX6UL boards/SoMs. + */ +#ifndef __KONTRON_MX6UL_CONFIG_H +#define __KONTRON_MX6UL_CONFIG_H + +/* DDR RAM */ +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM + +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +/* Board and environment settings */ +#define CONFIG_MXC_UART_BASE UART4_BASE +#define CONFIG_HOSTNAME "kontron-mx6ul" + +#define KONTRON_ENV_KERNEL_MTDPARTS "mtdparts=spi1.0:128k(spl),832k(u-boot),64k(env);spi4.0:192m(rootfs),-(user)" + +#define KONTRON_ENV_KERNEL_ADDR "0x82000000" +#define KONTRON_ENV_FDT_ADDR "0x83000000" +#define KONTRON_ENV_PXE_ADDR "0x83100000" +#define KONTRON_ENV_RAMDISK_ADDR "0x83200000" + +/* Common options for Kontron Electronics boards */ +#include "kontron_common.h" + +/* Boot order for distro boot */ +#ifndef CONFIG_SPL_BUILD +#define BOOT_TARGET_DEVICES(func) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 0) \ + func(UBIFS, ubifs, 0) \ + func(USB, usb, 0) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) +#include <config_distro_bootcmd.h> +#else +#define BOOTENV +#endif + +/* MMC Configs */ +#ifdef CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC1_BASE_ADDR +#define CONFIG_SYS_FSL_USDHC_NUM 2 +#define CONFIG_SYS_MMC_IMG_LOAD_PART 1 +#endif + +#endif /* __KONTRON_MX6UL_CONFIG_H */ -- 2.25.1

4 7

[PATCH v2 1/1] board: freescale: t104xrdb: Set popts->cpo_sample to 0x54 for DDR3
by Priyanka Singh 19 Aug '21

19 Aug '21

Set popts->cpo_sample to 0x54 in t104xrdb/ddr.c to optimize cpo Signed-off-by: Priyanka Singh <priyanka.singh(a)nxp.com> --- Changes for v2: -Added NXP Copyright to file updated --- board/freescale/t104xrdb/ddr.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c index 8351f7ce9d..539a36d2a9 100644 --- a/board/freescale/t104xrdb/ddr.c +++ b/board/freescale/t104xrdb/ddr.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2013 Freescale Semiconductor, Inc. + * Copyright 2021 NXP */ #include <common.h> @@ -83,6 +84,7 @@ found: /* optimize cpo for erratum A-009942 */ popts->cpo_sample = 0x59; #else + popts->cpo_sample = 0x54; popts->half_strength_driver_enable = 0; #endif /* -- 2.17.1

1 0