Add PSGTR driver for Xilinx ZynqMP.
The most of configurations are taken from Linux kernel psgtr driver.
USB3.0 and SGMII configurations are tested on SOM. In SGMII case also
IOU_SLCR reg is updated to get proper clock setup and signal detection
configuration.
Signed-off-by: Michal Simek <michal.simek(a)xilinx.com>
---
MAINTAINERS | 1 +
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-zynqmp.c | 690 +++++++++++++++++++++++++++++++++++++++
4 files changed, 699 insertions(+)
create mode 100644 drivers/phy/phy-zynqmp.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 1eb71cbdad12..d1e9fbd4a279 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -611,6 +611,7 @@ F: drivers/mmc/zynq_sdhci.c
F: drivers/mtd/nand/raw/zynq_nand.c
F: drivers/net/phy/xilinx_phy.c
F: drivers/net/zynq_gem.c
+F: drivers/phy/phy-zynqmp.c
F: drivers/serial/serial_zynq.c
F: drivers/reset/reset-zynqmp.c
F: drivers/rtc/zynqmp_rtc.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 4767d215f337..d79798429b18 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -281,6 +281,13 @@ config PHY_IMX8MQ_USB
help
Support the USB3.0 PHY in NXP i.MX8MQ SoC
+config PHY_XILINX_ZYNQMP
+ tristate "Xilinx ZynqMP PHY driver"
+ depends on PHY && ARCH_ZYNQMP
+ help
+ Enable this to support ZynqMP High Speed Gigabit Transceiver
+ that is part of ZynqMP SoC.
+
source "drivers/phy/rockchip/Kconfig"
source "drivers/phy/cadence/Kconfig"
source "drivers/phy/ti/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 13a8ade8919f..bf9b40932fe3 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -38,5 +38,6 @@ obj-$(CONFIG_MT76X8_USB_PHY) += mt76x8-usb-phy.o
obj-$(CONFIG_PHY_DA8XX_USB) += phy-da8xx-usb.o
obj-$(CONFIG_PHY_MTK_TPHY) += phy-mtk-tphy.o
obj-$(CONFIG_PHY_IMX8MQ_USB) += phy-imx8mq-usb.o
+obj-$(CONFIG_PHY_XILINX_ZYNQMP) += phy-zynqmp.o
obj-y += cadence/
obj-y += ti/
diff --git a/drivers/phy/phy-zynqmp.c b/drivers/phy/phy-zynqmp.c
new file mode 100644
index 000000000000..d6fe8dcef74e
--- /dev/null
+++ b/drivers/phy/phy-zynqmp.c
@@ -0,0 +1,690 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * phy-zynqmp.c - PHY driver for Xilinx ZynqMP GT.
+ *
+ * Copyright (C) 2018-2021 Xilinx Inc.
+ *
+ * Author: Anurag Kumar Vulisha <anuragku(a)xilinx.com>
+ * Author: Subbaraya Sundeep <sundeep.lkml(a)gmail.com>
+ * Author: Laurent Pinchart <laurent.pinchart(a)ideasonboard.com>
+ */
+
+#include <common.h>
+#include <clk-uclass.h>
+#include <dm.h>
+#include <log.h>
+#include <dm/device.h>
+#include <dm/device_compat.h>
+#include <dm/lists.h>
+#include <dt-bindings/phy/phy.h>
+#include <generic-phy.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <power-domain.h>
+#include <regmap.h>
+#include <syscon.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+
+#include <dt-bindings/phy/phy.h>
+
+#include <asm/arch/hardware.h>
+
+/*
+ * Lane Registers
+ */
+
+/* TX De-emphasis parameters */
+#define L0_TX_ANA_TM_18 0x0048
+#define L0_TX_ANA_TM_118 0x01d8
+#define L0_TX_ANA_TM_118_FORCE_17_0 BIT(0)
+
+/* DN Resistor calibration code parameters */
+#define L0_TXPMA_ST_3 0x0b0c
+#define L0_DN_CALIB_CODE 0x3f
+
+/* PMA control parameters */
+#define L0_TXPMD_TM_45 0x0cb4
+#define L0_TXPMD_TM_48 0x0cc0
+#define L0_TXPMD_TM_45_OVER_DP_MAIN BIT(0)
+#define L0_TXPMD_TM_45_ENABLE_DP_MAIN BIT(1)
+#define L0_TXPMD_TM_45_OVER_DP_POST1 BIT(2)
+#define L0_TXPMD_TM_45_ENABLE_DP_POST1 BIT(3)
+#define L0_TXPMD_TM_45_OVER_DP_POST2 BIT(4)
+#define L0_TXPMD_TM_45_ENABLE_DP_POST2 BIT(5)
+
+/* PCS control parameters */
+#define L0_TM_DIG_6 0x106c
+#define L0_TM_DIS_DESCRAMBLE_DECODER 0x0f
+#define L0_TX_DIG_61 0x00f4
+#define L0_TM_DISABLE_SCRAMBLE_ENCODER 0x0f
+
+/* PLL Test Mode register parameters */
+#define L0_TM_PLL_DIG_37 0x2094
+#define L0_TM_COARSE_CODE_LIMIT 0x10
+
+/* PLL SSC step size offsets */
+#define L0_PLL_SS_STEPS_0_LSB 0x2368
+#define L0_PLL_SS_STEPS_1_MSB 0x236c
+#define L0_PLL_SS_STEP_SIZE_0_LSB 0x2370
+#define L0_PLL_SS_STEP_SIZE_1 0x2374
+#define L0_PLL_SS_STEP_SIZE_2 0x2378
+#define L0_PLL_SS_STEP_SIZE_3_MSB 0x237c
+#define L0_PLL_STATUS_READ_1 0x23e4
+
+/* SSC step size parameters */
+#define STEP_SIZE_0_MASK 0xff
+#define STEP_SIZE_1_MASK 0xff
+#define STEP_SIZE_2_MASK 0xff
+#define STEP_SIZE_3_MASK 0x3
+#define STEP_SIZE_SHIFT 8
+#define FORCE_STEP_SIZE 0x10
+#define FORCE_STEPS 0x20
+#define STEPS_0_MASK 0xff
+#define STEPS_1_MASK 0x07
+
+/* Reference clock selection parameters */
+#define L0_Ln_REF_CLK_SEL(n) (0x2860 + (n) * 4)
+#define L0_REF_CLK_SEL_MASK 0x8f
+
+/* Calibration digital logic parameters */
+#define L3_TM_CALIB_DIG19 0xec4c
+#define L3_CALIB_DONE_STATUS 0xef14
+#define L3_TM_CALIB_DIG18 0xec48
+#define L3_TM_CALIB_DIG19_NSW 0x07
+#define L3_TM_CALIB_DIG18_NSW 0xe0
+#define L3_TM_OVERRIDE_NSW_CODE 0x20
+#define L3_CALIB_DONE 0x02
+#define L3_NSW_SHIFT 5
+#define L3_NSW_PIPE_SHIFT 4
+#define L3_NSW_CALIB_SHIFT 3
+
+#define PHY_REG_OFFSET 0x4000
+
+/*
+ * Global Registers
+ */
+
+/* Refclk selection parameters */
+#define PLL_REF_SEL(n) (0x10000 + (n) * 4)
+#define PLL_FREQ_MASK 0x1f
+#define PLL_STATUS_LOCKED 0x10
+
+/* Inter Connect Matrix parameters */
+#define ICM_CFG0 0x10010
+#define ICM_CFG1 0x10014
+#define ICM_CFG0_L0_MASK 0x07
+#define ICM_CFG0_L1_MASK 0x70
+#define ICM_CFG1_L2_MASK 0x07
+#define ICM_CFG2_L3_MASK 0x70
+#define ICM_CFG_SHIFT 4
+
+/* Inter Connect Matrix allowed protocols */
+#define ICM_PROTOCOL_PD 0x0
+#define ICM_PROTOCOL_PCIE 0x1
+#define ICM_PROTOCOL_SATA 0x2
+#define ICM_PROTOCOL_USB 0x3
+#define ICM_PROTOCOL_DP 0x4
+#define ICM_PROTOCOL_SGMII 0x5
+
+/* Test Mode common reset control parameters */
+#define TM_CMN_RST 0x10018
+#define TM_CMN_RST_EN 0x1
+#define TM_CMN_RST_SET 0x2
+#define TM_CMN_RST_MASK 0x3
+
+/* Bus width parameters */
+#define TX_PROT_BUS_WIDTH 0x10040
+#define RX_PROT_BUS_WIDTH 0x10044
+#define PROT_BUS_WIDTH_10 0x0
+#define PROT_BUS_WIDTH_20 0x1
+#define PROT_BUS_WIDTH_40 0x2
+#define PROT_BUS_WIDTH_MASK 0x3
+#define PROT_BUS_WIDTH_SHIFT 2
+
+/* Number of GT lanes */
+#define NUM_LANES 4
+
+/* SIOU SATA control register */
+#define SATA_CONTROL_OFFSET 0x0100
+
+/* Total number of controllers */
+#define CONTROLLERS_PER_LANE 5
+
+/* Protocol Type parameters */
+#define XPSGTR_TYPE_USB0 0 /* USB controller 0 */
+#define XPSGTR_TYPE_USB1 1 /* USB controller 1 */
+#define XPSGTR_TYPE_SATA_0 2 /* SATA controller lane 0 */
+#define XPSGTR_TYPE_SATA_1 3 /* SATA controller lane 1 */
+#define XPSGTR_TYPE_PCIE_0 4 /* PCIe controller lane 0 */
+#define XPSGTR_TYPE_PCIE_1 5 /* PCIe controller lane 1 */
+#define XPSGTR_TYPE_PCIE_2 6 /* PCIe controller lane 2 */
+#define XPSGTR_TYPE_PCIE_3 7 /* PCIe controller lane 3 */
+#define XPSGTR_TYPE_DP_0 8 /* Display Port controller lane 0 */
+#define XPSGTR_TYPE_DP_1 9 /* Display Port controller lane 1 */
+#define XPSGTR_TYPE_SGMII0 10 /* Ethernet SGMII controller 0 */
+#define XPSGTR_TYPE_SGMII1 11 /* Ethernet SGMII controller 1 */
+#define XPSGTR_TYPE_SGMII2 12 /* Ethernet SGMII controller 2 */
+#define XPSGTR_TYPE_SGMII3 13 /* Ethernet SGMII controller 3 */
+
+/* Timeout values */
+#define TIMEOUT_US 1000
+
+#define IOU_SLCR_GEM_CLK_CTRL 0x308
+#define GEM_CTRL_GEM_SGMII_MODE BIT(2)
+#define GEM_CTRL_GEM_REF_SRC_SEL BIT(1)
+
+#define IOU_SLCR_GEM_CTRL 0x360
+#define GEM_CTRL_GEM_SGMII_SD BIT(0)
+
+/**
+ * struct xpsgtr_ssc - structure to hold SSC settings for a lane
+ * @refclk_rate: PLL reference clock frequency
+ * @pll_ref_clk: value to be written to register for corresponding ref clk rate
+ * @steps: number of steps of SSC (Spread Spectrum Clock)
+ * @step_size: step size of each step
+ */
+struct xpsgtr_ssc {
+ u32 refclk_rate;
+ u8 pll_ref_clk;
+ u32 steps;
+ u32 step_size;
+};
+
+/**
+ * struct xpsgtr_phy - representation of a lane
+ * @dev: pointer to the xpsgtr_dev instance
+ * @refclk: reference clock index
+ * @type: controller which uses this lane
+ * @lane: lane number
+ * @protocol: protocol in which the lane operates
+ */
+struct xpsgtr_phy {
+ struct xpsgtr_dev *dev;
+ unsigned int refclk;
+ u8 type;
+ u8 lane;
+ u8 protocol;
+};
+
+/**
+ * struct xpsgtr_dev - representation of a ZynMP GT device
+ * @dev: pointer to device
+ * @serdes: serdes base address
+ * @siou: siou base address
+ * @phys: PHY lanes
+ * @refclk_sscs: spread spectrum settings for the reference clocks
+ * @clk: reference clocks
+ */
+struct xpsgtr_dev {
+ struct udevice *dev;
+ u8 *serdes;
+ u8 *siou;
+ struct xpsgtr_phy phys[NUM_LANES];
+ const struct xpsgtr_ssc *refclk_sscs[NUM_LANES];
+ struct clk clk[NUM_LANES];
+};
+
+/*
+ * Configuration Data
+ */
+/* lookup table to hold all settings needed for a ref clock frequency */
+static const struct xpsgtr_ssc ssc_lookup[] = {
+ { 19200000, 0x05, 608, 264020 },
+ { 20000000, 0x06, 634, 243454 },
+ { 24000000, 0x07, 760, 168973 },
+ { 26000000, 0x08, 824, 143860 },
+ { 27000000, 0x09, 856, 86551 },
+ { 38400000, 0x0a, 1218, 65896 },
+ { 40000000, 0x0b, 634, 243454 },
+ { 52000000, 0x0c, 824, 143860 },
+ { 100000000, 0x0d, 1058, 87533 },
+ { 108000000, 0x0e, 856, 86551 },
+ { 125000000, 0x0f, 992, 119497 },
+ { 135000000, 0x10, 1070, 55393 },
+ { 150000000, 0x11, 792, 187091 }
+};
+
+/*
+ * I/O Accessors
+ */
+
+static inline u32 xpsgtr_read(struct xpsgtr_dev *gtr_dev, u32 reg)
+{
+ return readl(gtr_dev->serdes + reg);
+}
+
+static inline void xpsgtr_write(struct xpsgtr_dev *gtr_dev, u32 reg, u32 value)
+{
+ writel(value, gtr_dev->serdes + reg);
+}
+
+static inline void xpsgtr_clr_set(struct xpsgtr_dev *gtr_dev, u32 reg,
+ u32 clr, u32 set)
+{
+ u32 value = xpsgtr_read(gtr_dev, reg);
+
+ value &= ~clr;
+ value |= set;
+ xpsgtr_write(gtr_dev, reg, value);
+}
+
+static inline u32 xpsgtr_read_phy(struct xpsgtr_phy *gtr_phy, u32 reg)
+{
+ void __iomem *addr = gtr_phy->dev->serdes
+ + gtr_phy->lane * PHY_REG_OFFSET + reg;
+
+ return readl(addr);
+}
+
+static inline void xpsgtr_write_phy(struct xpsgtr_phy *gtr_phy,
+ u32 reg, u32 value)
+{
+ void __iomem *addr = gtr_phy->dev->serdes
+ + gtr_phy->lane * PHY_REG_OFFSET + reg;
+
+ writel(value, addr);
+}
+
+static inline void xpsgtr_clr_set_phy(struct xpsgtr_phy *gtr_phy,
+ u32 reg, u32 clr, u32 set)
+{
+ void __iomem *addr = gtr_phy->dev->serdes
+ + gtr_phy->lane * PHY_REG_OFFSET + reg;
+
+ writel((readl(addr) & ~clr) | set, addr);
+}
+
+/* Configure PLL and spread-sprectrum clock. */
+static void xpsgtr_configure_pll(struct xpsgtr_phy *gtr_phy)
+{
+ const struct xpsgtr_ssc *ssc;
+ u32 step_size;
+
+ ssc = gtr_phy->dev->refclk_sscs[gtr_phy->refclk];
+ step_size = ssc->step_size;
+
+ xpsgtr_clr_set(gtr_phy->dev, PLL_REF_SEL(gtr_phy->lane),
+ PLL_FREQ_MASK, ssc->pll_ref_clk);
+
+ /* Enable lane clock sharing, if required */
+ if (gtr_phy->refclk != gtr_phy->lane) {
+ /* Lane3 Ref Clock Selection Register */
+ xpsgtr_clr_set(gtr_phy->dev, L0_Ln_REF_CLK_SEL(gtr_phy->lane),
+ L0_REF_CLK_SEL_MASK, 1 << gtr_phy->refclk);
+ }
+
+ /* SSC step size [7:0] */
+ xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEP_SIZE_0_LSB,
+ STEP_SIZE_0_MASK, step_size & STEP_SIZE_0_MASK);
+
+ /* SSC step size [15:8] */
+ step_size >>= STEP_SIZE_SHIFT;
+ xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEP_SIZE_1,
+ STEP_SIZE_1_MASK, step_size & STEP_SIZE_1_MASK);
+
+ /* SSC step size [23:16] */
+ step_size >>= STEP_SIZE_SHIFT;
+ xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEP_SIZE_2,
+ STEP_SIZE_2_MASK, step_size & STEP_SIZE_2_MASK);
+
+ /* SSC steps [7:0] */
+ xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEPS_0_LSB,
+ STEPS_0_MASK, ssc->steps & STEPS_0_MASK);
+
+ /* SSC steps [10:8] */
+ xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEPS_1_MSB,
+ STEPS_1_MASK,
+ (ssc->steps >> STEP_SIZE_SHIFT) & STEPS_1_MASK);
+
+ /* SSC step size [24:25] */
+ step_size >>= STEP_SIZE_SHIFT;
+ xpsgtr_clr_set_phy(gtr_phy, L0_PLL_SS_STEP_SIZE_3_MSB,
+ STEP_SIZE_3_MASK, (step_size & STEP_SIZE_3_MASK) |
+ FORCE_STEP_SIZE | FORCE_STEPS);
+}
+
+/* Configure the lane protocol. */
+static void xpsgtr_lane_set_protocol(struct xpsgtr_phy *gtr_phy)
+{
+ struct xpsgtr_dev *gtr_dev = gtr_phy->dev;
+ u8 protocol = gtr_phy->protocol;
+
+ switch (gtr_phy->lane) {
+ case 0:
+ xpsgtr_clr_set(gtr_dev, ICM_CFG0, ICM_CFG0_L0_MASK, protocol);
+ break;
+ case 1:
+ xpsgtr_clr_set(gtr_dev, ICM_CFG0, ICM_CFG0_L1_MASK,
+ protocol << ICM_CFG_SHIFT);
+ break;
+ case 2:
+ xpsgtr_clr_set(gtr_dev, ICM_CFG1, ICM_CFG0_L0_MASK, protocol);
+ break;
+ case 3:
+ xpsgtr_clr_set(gtr_dev, ICM_CFG1, ICM_CFG0_L1_MASK,
+ protocol << ICM_CFG_SHIFT);
+ break;
+ default:
+ /* We already checked 0 <= lane <= 3 */
+ break;
+ }
+}
+
+/* Bypass (de)scrambler and 8b/10b decoder and encoder. */
+static void xpsgtr_bypass_scrambler_8b10b(struct xpsgtr_phy *gtr_phy)
+{
+ xpsgtr_write_phy(gtr_phy, L0_TM_DIG_6, L0_TM_DIS_DESCRAMBLE_DECODER);
+ xpsgtr_write_phy(gtr_phy, L0_TX_DIG_61, L0_TM_DISABLE_SCRAMBLE_ENCODER);
+}
+
+/* SGMII-specific initialization. */
+static void xpsgtr_phy_init_sgmii(struct xpsgtr_phy *gtr_phy)
+{
+ struct xpsgtr_dev *gtr_dev = gtr_phy->dev;
+ u32 shift = gtr_phy->lane * PROT_BUS_WIDTH_SHIFT;
+
+ /* Set SGMII protocol TX and RX bus width to 10 bits. */
+ xpsgtr_clr_set(gtr_dev, TX_PROT_BUS_WIDTH, PROT_BUS_WIDTH_MASK << shift,
+ PROT_BUS_WIDTH_10 << shift);
+
+ xpsgtr_clr_set(gtr_dev, RX_PROT_BUS_WIDTH, PROT_BUS_WIDTH_MASK << shift,
+ PROT_BUS_WIDTH_10 << shift);
+
+ xpsgtr_bypass_scrambler_8b10b(gtr_phy);
+
+ /*
+ * Below code is just temporary solution till we have a way how to
+ * do it via firmware interface in sync with Linux. Till that happen
+ * this is the most sensible thing to do here.
+ */
+ /* GEM I/O Clock Control */
+ clrsetbits_le32(ZYNQMP_IOU_SLCR_BASEADDR + IOU_SLCR_GEM_CLK_CTRL,
+ 0xf << shift,
+ (GEM_CTRL_GEM_SGMII_MODE | GEM_CTRL_GEM_REF_SRC_SEL) <<
+ shift);
+
+ /* Setup signal detect */
+ clrsetbits_le32(ZYNQMP_IOU_SLCR_BASEADDR + IOU_SLCR_GEM_CTRL,
+ PROT_BUS_WIDTH_MASK << shift,
+ GEM_CTRL_GEM_SGMII_SD << shift);
+}
+
+static int xpsgtr_init(struct phy *x)
+{
+ struct xpsgtr_dev *gtr_dev = dev_get_priv(x->dev);
+ struct xpsgtr_phy *gtr_phy;
+ u32 phy_lane = x->id;
+
+ gtr_phy = >r_dev->phys[phy_lane];
+
+ /* Enable coarse code saturation limiting logic. */
+ xpsgtr_write_phy(gtr_phy, L0_TM_PLL_DIG_37, L0_TM_COARSE_CODE_LIMIT);
+
+ /*
+ * Configure the PLL, the lane protocol, and perform protocol-specific
+ * initialization.
+ */
+ xpsgtr_configure_pll(gtr_phy);
+ xpsgtr_lane_set_protocol(gtr_phy);
+
+ switch (gtr_phy->protocol) {
+ case ICM_PROTOCOL_SGMII:
+ xpsgtr_phy_init_sgmii(gtr_phy);
+ break;
+ case ICM_PROTOCOL_DP:
+ case ICM_PROTOCOL_SATA:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+/*
+ * OF Xlate Support
+ */
+
+/* Set the lane type and protocol based on the PHY type and instance number. */
+static int xpsgtr_set_lane_type(struct xpsgtr_phy *gtr_phy, u8 phy_type,
+ unsigned int phy_instance)
+{
+ unsigned int num_phy_types;
+ const int *phy_types;
+
+ switch (phy_type) {
+ case PHY_TYPE_SATA: {
+ static const int types[] = {
+ XPSGTR_TYPE_SATA_0,
+ XPSGTR_TYPE_SATA_1,
+ };
+
+ phy_types = types;
+ num_phy_types = ARRAY_SIZE(types);
+ gtr_phy->protocol = ICM_PROTOCOL_SATA;
+ break;
+ }
+ case PHY_TYPE_USB3: {
+ static const int types[] = {
+ XPSGTR_TYPE_USB0,
+ XPSGTR_TYPE_USB1,
+ };
+
+ phy_types = types;
+ num_phy_types = ARRAY_SIZE(types);
+ gtr_phy->protocol = ICM_PROTOCOL_USB;
+ break;
+ }
+ case PHY_TYPE_DP: {
+ static const int types[] = {
+ XPSGTR_TYPE_DP_0,
+ XPSGTR_TYPE_DP_1,
+ };
+
+ phy_types = types;
+ num_phy_types = ARRAY_SIZE(types);
+ gtr_phy->protocol = ICM_PROTOCOL_DP;
+ break;
+ }
+ case PHY_TYPE_PCIE: {
+ static const int types[] = {
+ XPSGTR_TYPE_PCIE_0,
+ XPSGTR_TYPE_PCIE_1,
+ XPSGTR_TYPE_PCIE_2,
+ XPSGTR_TYPE_PCIE_3,
+ };
+
+ phy_types = types;
+ num_phy_types = ARRAY_SIZE(types);
+ gtr_phy->protocol = ICM_PROTOCOL_PCIE;
+ break;
+ }
+ case PHY_TYPE_SGMII: {
+ static const int types[] = {
+ XPSGTR_TYPE_SGMII0,
+ XPSGTR_TYPE_SGMII1,
+ XPSGTR_TYPE_SGMII2,
+ XPSGTR_TYPE_SGMII3,
+ };
+
+ phy_types = types;
+ num_phy_types = ARRAY_SIZE(types);
+ gtr_phy->protocol = ICM_PROTOCOL_SGMII;
+ break;
+ }
+ default:
+ return -EINVAL;
+ }
+
+ if (phy_instance >= num_phy_types)
+ return -EINVAL;
+
+ gtr_phy->type = phy_types[phy_instance];
+ return 0;
+}
+
+/*
+ * Valid combinations of controllers and lanes (Interconnect Matrix).
+ */
+static const unsigned int icm_matrix[NUM_LANES][CONTROLLERS_PER_LANE] = {
+ { XPSGTR_TYPE_PCIE_0, XPSGTR_TYPE_SATA_0, XPSGTR_TYPE_USB0,
+ XPSGTR_TYPE_DP_1, XPSGTR_TYPE_SGMII0 },
+ { XPSGTR_TYPE_PCIE_1, XPSGTR_TYPE_SATA_1, XPSGTR_TYPE_USB0,
+ XPSGTR_TYPE_DP_0, XPSGTR_TYPE_SGMII1 },
+ { XPSGTR_TYPE_PCIE_2, XPSGTR_TYPE_SATA_0, XPSGTR_TYPE_USB0,
+ XPSGTR_TYPE_DP_1, XPSGTR_TYPE_SGMII2 },
+ { XPSGTR_TYPE_PCIE_3, XPSGTR_TYPE_SATA_1, XPSGTR_TYPE_USB1,
+ XPSGTR_TYPE_DP_0, XPSGTR_TYPE_SGMII3 }
+};
+
+/* Translate OF phandle and args to PHY instance. */
+static int xpsgtr_of_xlate(struct phy *x,
+ struct ofnode_phandle_args *args)
+{
+ struct xpsgtr_dev *gtr_dev = dev_get_priv(x->dev);
+ struct xpsgtr_phy *gtr_phy;
+ struct udevice *dev = x->dev;
+ unsigned int phy_instance;
+ unsigned int phy_lane;
+ unsigned int phy_type;
+ unsigned int refclk;
+ unsigned int i;
+ int ret;
+
+ if (args->args_count != 4) {
+ dev_err(dev, "Invalid number of cells in 'phy' property\n");
+ return -EINVAL;
+ }
+
+ /*
+ * Get the PHY parameters from the OF arguments and derive the lane
+ * type.
+ */
+ phy_lane = args->args[0];
+ if (phy_lane >= NUM_LANES) {
+ dev_err(dev, "Invalid lane number %u\n", phy_lane);
+ return -ENODEV;
+ }
+
+ gtr_phy = >r_dev->phys[phy_lane];
+ phy_type = args->args[1];
+ phy_instance = args->args[2];
+
+ ret = xpsgtr_set_lane_type(gtr_phy, phy_type, phy_instance);
+ if (ret < 0) {
+ dev_err(dev, "Invalid PHY type and/or instance\n");
+ return ret;
+ }
+
+ refclk = args->args[3];
+ if (refclk >= ARRAY_SIZE(gtr_dev->refclk_sscs) ||
+ !gtr_dev->refclk_sscs[refclk]) {
+ dev_err(dev, "Invalid reference clock number %u\n", refclk);
+ return -EINVAL;
+ }
+
+ gtr_phy->refclk = refclk;
+
+ /* This is difference compare to Linux */
+ gtr_phy->dev = gtr_dev;
+ gtr_phy->lane = phy_lane;
+
+ /*
+ * Ensure that the Interconnect Matrix is obeyed, i.e a given lane type
+ * is allowed to operate on the lane.
+ */
+ for (i = 0; i < CONTROLLERS_PER_LANE; i++) {
+ if (icm_matrix[phy_lane][i] == gtr_phy->type) {
+ x->id = phy_lane;
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+/*
+ * Probe & Platform Driver
+ */
+static int xpsgtr_get_ref_clocks(struct udevice *dev)
+{
+ unsigned int refclk;
+ struct xpsgtr_dev *gtr_dev = dev_get_priv(dev);
+ int ret;
+
+ for (refclk = 0; refclk < 4; ++refclk) {
+ int i;
+ u32 rate;
+ char name[8];
+ struct clk *clk = >r_dev->clk[refclk];
+
+ snprintf(name, sizeof(name), "ref%u", refclk);
+ dev_dbg(dev, "Checking name: %s\n", name);
+ ret = clk_get_by_name(dev, name, clk);
+ if (ret)
+ continue;
+
+ rate = clk_get_rate(clk);
+
+ dev_dbg(dev, "clk rate %d\n", rate);
+
+ ret = clk_enable(clk);
+ if (ret) {
+ dev_err(dev, "failed to enable refclk %d clock\n",
+ refclk);
+ return ret;
+ }
+
+ for (i = 0 ; i < ARRAY_SIZE(ssc_lookup); i++) {
+ if (rate == ssc_lookup[i].refclk_rate) {
+ gtr_dev->refclk_sscs[refclk] = &ssc_lookup[i];
+ dev_dbg(dev, "Found rate %d\n", i);
+ break;
+ }
+ }
+
+ if (i == ARRAY_SIZE(ssc_lookup)) {
+ dev_err(dev,
+ "Invalid rate %u for reference clock %u\n",
+ rate, refclk);
+ return -EINVAL;
+ }
+ }
+
+ return 0;
+}
+
+static int xpsgtr_probe(struct udevice *dev)
+{
+ struct xpsgtr_dev *gtr_dev = dev_get_priv(dev);
+
+ gtr_dev->serdes = (u8 *)dev_read_addr_name(dev, "serdes");
+ if (!gtr_dev->serdes)
+ return -ENODEV;
+
+ gtr_dev->siou = (u8 *)dev_read_addr_name(dev, "siou");
+ if (!gtr_dev->siou)
+ return -ENODEV;
+
+ gtr_dev->dev = dev;
+
+ return xpsgtr_get_ref_clocks(dev);
+}
+
+static const struct udevice_id xpsgtr_phy_ids[] = {
+ { .compatible = "xlnx,zynqmp-psgtr-v1.1", },
+ { }
+};
+
+static const struct phy_ops xpsgtr_phy_ops = {
+ .init = xpsgtr_init,
+ .of_xlate = xpsgtr_of_xlate,
+};
+
+U_BOOT_DRIVER(psgtr_phy) = {
+ .name = "psgtr_phy",
+ .id = UCLASS_PHY,
+ .of_match = xpsgtr_phy_ids,
+ .ops = &xpsgtr_phy_ops,
+ .probe = xpsgtr_probe,
+ .priv_auto = sizeof(struct xpsgtr_dev),
+};
--
2.33.1
