Introduce pinctrl for i.MX6
1. pinctrl-imx.c is for common usage. It's used by i.MX6/7.
2. Add PINCTRL_IMX PINCTRL_IMX6 Kconfig entry.
3. To the pinctrl_ops implementation, only set_state is implemented.
To i.MX6/7, the pinctrl dts entry is as following:
&iomuxc {
pinctrl-names = "default";
pinctrl_csi1: csi1grp {
fsl,pins = <
MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
>;
};
[.....]
};
there is no property named function or groups. So pinctrl_generic_set_state
can not be used here.
5. This driver is a simple implementation for i.mx iomux controller,
only parse the fsl,pins property and write value to registers.
6. With DEBUG enabled, we can see log when "i2c bus 0":
"
set_state_simple op missing
imx_pinctrl_set_state: i2c1grp
mux_reg 0x14c, conf_reg 0x3bc, input_reg 0x5d8, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x14c val 0x10
select_input: offset 0x5d8 val 0x1
write config: offset 0x3bc val 0x7f
mux_reg 0x148, conf_reg 0x3b8, input_reg 0x5d4, mux_mode 0x0, input_val 0x1, config_val 0x4000007f
write mux: offset 0x148 val 0x10
select_input: offset 0x5d4 val 0x1
write config: offset 0x3b8 val 0x7f
"
this means imx6 pinctrl driver works as expected.
Signed-off-by: Peng Fan <van.freenix(a)gmail.com>
Reviewed-by: Simon Glass <sjg(a)chromium.org>
---
V2:
Add more details in Kconfig entry
Use fdt_getprop and fdtdec_get_int_array as suggested by Simon
Add reviewed-by Simon
Refer linux binding doc in code.
drivers/pinctrl/Kconfig | 1 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/nxp/Kconfig | 16 +++
drivers/pinctrl/nxp/Makefile | 2 +
drivers/pinctrl/nxp/pinctrl-imx.c | 241 +++++++++++++++++++++++++++++++++++++
drivers/pinctrl/nxp/pinctrl-imx.h | 50 ++++++++
drivers/pinctrl/nxp/pinctrl-imx6.c | 41 +++++++
7 files changed, 352 insertions(+)
create mode 100644 drivers/pinctrl/nxp/Kconfig
create mode 100644 drivers/pinctrl/nxp/Makefile
create mode 100644 drivers/pinctrl/nxp/pinctrl-imx.c
create mode 100644 drivers/pinctrl/nxp/pinctrl-imx.h
create mode 100644 drivers/pinctrl/nxp/pinctrl-imx6.c
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 57e6142..9fd8f62 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -133,6 +133,7 @@ config PINCTRL_SANDBOX
endif
+source "drivers/pinctrl/nxp/Kconfig"
source "drivers/pinctrl/uniphier/Kconfig"
endmenu
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 70d25dc..dcd20bf 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -5,6 +5,7 @@
obj-y += pinctrl-uclass.o
obj-$(CONFIG_$(SPL_)PINCTRL_GENERIC) += pinctrl-generic.o
+obj-y += nxp/
obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/
obj-$(CONFIG_PINCTRL_SANDBOX) += pinctrl-sandbox.o
diff --git a/drivers/pinctrl/nxp/Kconfig b/drivers/pinctrl/nxp/Kconfig
new file mode 100644
index 0000000..f1c9b92
--- /dev/null
+++ b/drivers/pinctrl/nxp/Kconfig
@@ -0,0 +1,16 @@
+config PINCTRL_IMX
+ bool
+
+config PINCTRL_IMX6
+ bool "IMX6 pinctrl driver"
+ depends on ARCH_MX6 && PINCTRL_FULL
+ select DEVRES
+ select PINCTRL_IMX
+ help
+ Say Y here to enable the imx6 pinctrl driver
+
+ This provides a simple pinctrl driver for i.MX6 SoC familiy,
+ i.MX6DQ/SL/SX/UL/DQP. This feature depends on device tree
+ configuration. This driver is different from the linux one,
+ this is a simple implementation, only parses the 'fsl,pins'
+ property and configure related registers.
diff --git a/drivers/pinctrl/nxp/Makefile b/drivers/pinctrl/nxp/Makefile
new file mode 100644
index 0000000..7fd9850
--- /dev/null
+++ b/drivers/pinctrl/nxp/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o
+obj-$(CONFIG_PINCTRL_IMX6) += pinctrl-imx6.o
diff --git a/drivers/pinctrl/nxp/pinctrl-imx.c b/drivers/pinctrl/nxp/pinctrl-imx.c
new file mode 100644
index 0000000..40b0616
--- /dev/null
+++ b/drivers/pinctrl/nxp/pinctrl-imx.c
@@ -0,0 +1,241 @@
+/*
+ * Copyright (C) 2016 Peng Fan <van.freenix(a)gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <mapmem.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <dm/device.h>
+#include <dm/pinctrl.h>
+
+#include "pinctrl-imx.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int imx_pinctrl_set_state(struct udevice *dev, struct udevice *config)
+{
+ struct imx_pinctrl_priv *priv = dev_get_priv(dev);
+ struct imx_pinctrl_soc_info *info = priv->info;
+ int node = config->of_offset;
+ const struct fdt_property *prop;
+ u32 *pin_data;
+ int npins, size, pin_size;
+ int mux_reg, conf_reg, input_reg, input_val, mux_mode, config_val;
+ int i, j = 0;
+
+ dev_dbg(dev, "%s: %s\n", __func__, config->name);
+
+ if (info->flags & SHARE_MUX_CONF_REG)
+ pin_size = SHARE_FSL_PIN_SIZE;
+ else
+ pin_size = FSL_PIN_SIZE;
+
+ prop = fdt_getprop(gd->fdt_blob, node, "fsl,pins", &size);
+ if (!prop) {
+ dev_err(dev, "No fsl,pins property in node %s\n", config->name);
+ return -EINVAL;
+ }
+
+ if (!size || size % pin_size) {
+ dev_err(dev, "Invalid fsl,pins property in node %s\n",
+ config->name);
+ return -EINVAL;
+ }
+
+ pin_data = devm_kzalloc(dev, size, 0);
+ if (!pin_data)
+ return -ENOMEM;
+
+ if (fdtdec_get_int_array(gd->fdt_blob, node, "fsl,pins",
+ pin_data, size >> 2)) {
+ dev_err(dev, "Error reading pin data.\n");
+ return -EINVAL;
+ }
+
+ npins = size / pin_size;
+
+ /*
+ * Refer to linux documentation for details:
+ * Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
+ */
+ for (i = 0; i < npins; i++) {
+ mux_reg = pin_data[j++];
+
+ if (!(info->flags & ZERO_OFFSET_VALID) && !mux_reg)
+ mux_reg = -1;
+
+ if (info->flags & SHARE_MUX_CONF_REG) {
+ conf_reg = mux_reg;
+ } else {
+ conf_reg = pin_data[j++];
+ if (!(info->flags & ZERO_OFFSET_VALID) && !conf_reg)
+ conf_reg = -1;
+ }
+
+ if ((mux_reg == -1) || (conf_reg == -1)) {
+ dev_err(dev, "Error mux_reg or conf_reg\n");
+ return -EINVAL;
+ }
+
+ input_reg = pin_data[j++];
+ mux_mode = pin_data[j++];
+ input_val = pin_data[j++];
+ config_val = pin_data[j++];
+
+ dev_dbg(dev, "mux_reg 0x%x, conf_reg 0x%x, input_reg 0x%x, "
+ "mux_mode 0x%x, input_val 0x%x, config_val 0x%x\n",
+ mux_reg, conf_reg, input_reg, mux_mode, input_val,
+ config_val);
+
+ if (config_val & IMX_PAD_SION)
+ mux_mode |= IOMUXC_CONFIG_SION;
+
+ config_val &= ~IMX_PAD_SION;
+
+ /* Set Mux */
+ if (info->flags & SHARE_MUX_CONF_REG) {
+ clrsetbits_le32(info->base + mux_reg, 0x7 << 20,
+ mux_mode << 20);
+ } else {
+ writel(mux_mode, info->base + mux_reg);
+ }
+
+ dev_dbg(dev, "write mux: offset 0x%x val 0x%x\n", mux_reg,
+ mux_mode);
+
+ /*
+ * Set select input
+ *
+ * If the select input value begins with 0xff, it's a quirky
+ * select input and the value should be interpreted as below.
+ * 31 23 15 7 0
+ * | 0xff | shift | width | select |
+ * It's used to work around the problem that the select
+ * input for some pin is not implemented in the select
+ * input register but in some general purpose register.
+ * We encode the select input value, width and shift of
+ * the bit field into input_val cell of pin function ID
+ * in device tree, and then decode them here for setting
+ * up the select input bits in general purpose register.
+ */
+
+ if (input_val >> 24 == 0xff) {
+ u32 val = input_val;
+ u8 select = val & 0xff;
+ u8 width = (val >> 8) & 0xff;
+ u8 shift = (val >> 16) & 0xff;
+ u32 mask = ((1 << width) - 1) << shift;
+ /*
+ * The input_reg[i] here is actually some IOMUXC general
+ * purpose register, not regular select input register.
+ */
+ val = readl(info->base + input_reg);
+ val &= ~mask;
+ val |= select << shift;
+ writel(val, info->base + input_reg);
+ } else if (input_reg) {
+ /*
+ * Regular select input register can never be at offset
+ * 0, and we only print register value for regular case.
+ */
+ if (info->input_sel_base)
+ writel(input_val, info->input_sel_base +
+ input_reg);
+ else
+ writel(input_val, info->base + input_reg);
+
+ dev_dbg(dev, "select_input: offset 0x%x val 0x%x\n",
+ input_reg, input_val);
+ }
+
+ /* Set config */
+ if (!(config_val & IMX_NO_PAD_CTL)) {
+ if (info->flags & SHARE_MUX_CONF_REG) {
+ clrsetbits_le32(info->base + conf_reg, 0xffff,
+ config_val);
+ } else {
+ writel(config_val, info->base + conf_reg);
+ }
+
+ dev_dbg(dev, "write config: offset 0x%x val 0x%x\n",
+ conf_reg, config_val);
+ }
+ }
+
+ return 0;
+}
+
+const struct pinctrl_ops imx_pinctrl_ops = {
+ .set_state = imx_pinctrl_set_state,
+};
+
+int imx_pinctrl_probe(struct udevice *dev,
+ struct imx_pinctrl_soc_info *info)
+{
+ struct imx_pinctrl_priv *priv = dev_get_priv(dev);
+ int node = dev->of_offset, ret;
+ struct fdtdec_phandle_args arg;
+ fdt_addr_t addr;
+ fdt_size_t size;
+
+ if (!info) {
+ dev_err(dev, "wrong pinctrl info\n");
+ return -EINVAL;
+ }
+
+ priv->dev = dev;
+ priv->info = info;
+
+ addr = fdtdec_get_addr_size(gd->fdt_blob, dev->of_offset, "reg", &size);
+
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ info->base = map_sysmem(addr, size);
+ if (!info->base)
+ return -ENOMEM;
+ priv->info = info;
+
+ /*
+ * Refer to linux documentation for details:
+ * Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
+ */
+ if (fdtdec_get_bool(gd->fdt_blob, node, "fsl,input-sel")) {
+ ret = fdtdec_parse_phandle_with_args(gd->fdt_blob,
+ node, "fsl,input-sel",
+ NULL, 0, 0, &arg);
+ if (ret) {
+ dev_err(dev, "iomuxc fsl,input-sel property not found\n");
+ return -EINVAL;
+ }
+
+ addr = fdtdec_get_addr_size(gd->fdt_blob, arg.node, "reg",
+ &size);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ info->input_sel_base = map_sysmem(addr, size);
+ if (!info->input_sel_base)
+ return -ENOMEM;
+ }
+
+ dev_info(dev, "initialized IMX pinctrl driver\n");
+
+ return 0;
+}
+
+int imx_pinctrl_remove(struct udevice *dev)
+{
+ struct imx_pinctrl_priv *priv = dev_get_priv(dev);
+ struct imx_pinctrl_soc_info *info = priv->info;
+
+ if (info->input_sel_base)
+ unmap_sysmem(info->input_sel_base);
+ if (info->base)
+ unmap_sysmem(info->base);
+
+ return 0;
+}
diff --git a/drivers/pinctrl/nxp/pinctrl-imx.h b/drivers/pinctrl/nxp/pinctrl-imx.h
new file mode 100644
index 0000000..037c491
--- /dev/null
+++ b/drivers/pinctrl/nxp/pinctrl-imx.h
@@ -0,0 +1,50 @@
+/*
+ * Copyright (C) 2016 Peng Fan <van.freenix(a)gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DRIVERS_PINCTRL_IMX_H
+#define __DRIVERS_PINCTRL_IMX_H
+
+/**
+ * @base: the address to the controller in virtual memory
+ * @input_sel_base: the address of the select input in virtual memory.
+ * @flags: flags specific for each soc
+ */
+struct imx_pinctrl_soc_info {
+ void __iomem *base;
+ void __iomem *input_sel_base;
+ unsigned int flags;
+};
+
+/**
+ * @dev: a pointer back to containing device
+ * @info: the soc info
+ */
+struct imx_pinctrl_priv {
+ struct udevice *dev;
+ struct imx_pinctrl_soc_info *info;
+};
+
+extern const struct pinctrl_ops imx_pinctrl_ops;
+
+#define IMX_NO_PAD_CTL 0x80000000 /* no pin config need */
+#define IMX_PAD_SION 0x40000000 /* set SION */
+
+/*
+ * Each pin represented in fsl,pins consists of 5 u32 PIN_FUNC_ID and
+ * 1 u32 CONFIG, so 24 types in total for each pin.
+ */
+#define FSL_PIN_SIZE 24
+#define SHARE_FSL_PIN_SIZE 20
+
+#define SHARE_MUX_CONF_REG 0x1
+#define ZERO_OFFSET_VALID 0x2
+
+#define IOMUXC_CONFIG_SION (0x1 << 4)
+
+int imx_pinctrl_probe(struct udevice *dev, struct imx_pinctrl_soc_info *info);
+
+int imx_pinctrl_remove(struct udevice *dev);
+#endif /* __DRIVERS_PINCTRL_IMX_H */
diff --git a/drivers/pinctrl/nxp/pinctrl-imx6.c b/drivers/pinctrl/nxp/pinctrl-imx6.c
new file mode 100644
index 0000000..24f139e
--- /dev/null
+++ b/drivers/pinctrl/nxp/pinctrl-imx6.c
@@ -0,0 +1,41 @@
+
+/*
+ * Copyright (C) 2016 Peng Fan <van.freenix(a)gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <dm/device.h>
+#include <dm/pinctrl.h>
+
+#include "pinctrl-imx.h"
+
+static struct imx_pinctrl_soc_info imx6_pinctrl_soc_info;
+
+static int imx6_pinctrl_probe(struct udevice *dev)
+{
+ struct imx_pinctrl_soc_info *info =
+ (struct imx_pinctrl_soc_info *)dev_get_driver_data(dev);
+
+ return imx_pinctrl_probe(dev, info);
+}
+
+static const struct udevice_id imx6_pinctrl_match[] = {
+ { .compatible = "fsl,imx6q-iomuxc", .data = (ulong)&imx6_pinctrl_soc_info },
+ { .compatible = "fsl,imx6dl-iomuxc", .data = (ulong)&imx6_pinctrl_soc_info },
+ { .compatible = "fsl,imx6sl-iomuxc", .data = (ulong)&imx6_pinctrl_soc_info },
+ { .compatible = "fsl,imx6sx-iomuxc", .data = (ulong)&imx6_pinctrl_soc_info },
+ { .compatible = "fsl,imx6ul-iomuxc", .data = (ulong)&imx6_pinctrl_soc_info },
+ { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(imx6_pinctrl) = {
+ .name = "imx6-pinctrl",
+ .id = UCLASS_PINCTRL,
+ .of_match = of_match_ptr(imx6_pinctrl_match),
+ .probe = imx6_pinctrl_probe,
+ .remove = imx_pinctrl_remove,
+ .priv_auto_alloc_size = sizeof(struct imx_pinctrl_priv),
+ .ops = &imx_pinctrl_ops,
+ .flags = DM_FLAG_PRE_RELOC,
+};
--
2.6.2
